RVCGM-80C Rear View Integration Interface for Select GM Vehicles with CUE, Intellilink and MyLink Systems

Transcription

1 VCGM-80C ear View Integration Interface for Select PODUCT FEATUES: - Automatically switches to rear-view when vehicle is put in reverse gear. - Provides reverse camera input. - Adds 3 Audio/Video inputs. - Plug and play installation. PATS INCLUDED: VCGM-80C Module emote Control Power Harness I Extension Cable LVDS Cable A/V Cable Camera Power Harness Push Button Switch 1 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

2 VCGM-80C ear View Integration Interface for Select INSTALLATION DIAGAM: Plug to HMI Module Connect to Blue Mini USB Plug from HMI Module GM-80C LVDS T-HANESS DIP SWITCHES EA-VIEW INTEGATION LVDS Output VCGM-80C STATUS LED 24-PIN POWE PLUG 24-Pin Audio/Video IN/OUT +12V ACC GOUND PUSH BUTTON SWITCH I EMOTE CABLE Fuse Box AV1 AV2 AV3 AV OUT GB CABLE +12V GOUND CAMEA POWE 2 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

3 VCGM-80C ear View Integration Interface for Select INSTALLATION INSTUCTIONS: Follow these steps to properly install the interface module. Note that this interface connects to the HMI Module. 1. emove the GLOVE BOX to gain access to the factory HMI module. The HMI module is located in different areas depending on the vehicle model. Below is a list of vehicles and where the HMI module can be located: Cadillac ATS/CTS = below the glove box Cadillac SX = below or behind the glove box Corvette = driver side kick panel Once you have located the HMI module, unplug the BLUE LVDS connector. You will need to plug this to the VCGM-80C Main Interface Module. Factory LVDS Connector 2. Using the provided 24-Pin Power Harness, connect the loose wires on the 24-Pin as mentioned below. You can tap Accessory power from the cigarette lighter (+12V switched) position. NOT ALL LOOSE WIES ON THE 24-PIN CONNECTO AE USED ED BLACK BLUE GAY = Accessory = Ground = Parking = everse Input Factory Mini USB (LVDS) connections are mostly located on the MyLink System box. 3. After making the connections on the 24-Pin harness, insert the 24-Pin into the Main Interface module. Make sure that the connector is properly seated into the module. 3 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

4 VCGM-80C ear View Integration Interface for Select After connecting the module, set the proper DIP switches to the ON position. Make sure to set the AV sources being used to the ON position. NOTE: The Video-In-Motion feature does not require activation. This feature is permanently ON and will not disturb the Navigation GPS performance. MAIN INTEFACE MODULE POWE CAN-BU S POWE DATALINK DIP SWITCH DESCIPTION UP = ON DOWN = DIP 1 = ON = GB Enable / OFF= Disable DIP 2 = ON =AV1 Enable / OFF= Disable DIP 3 = ON =AV2 Enable / OFF= Disable DIP 4 = ON =AV3 Enable / OFF= Disable DIP 5 = Not Used DIP 6 = Not Used DIP 7 = ON = A ermarket Camera Enable DIP 8 = Not Used LED INDICATOS DATA LINK STATUS: Blinking = No BUS Detected. Solid= BUS ecognized. OFF = Power Down / Sleep Mode. POWE STATUS: ON = Power On OFF = Power O NOTES: - Before c onnec ng t he m ain modu le, set the proper DIP switch to the ON posi n. - Make sure to set the AV source being used to the ON posi n. - After each change of the DIP switch se ngs, we recommend powering down the module, then restar ng the vehicle. - The Video-In-Mo n feature does not require ac va n. This feature is p ermane ntly O N and will not disturb the GPS performance. CONNECTING THE CAMEA & AV INPUTS: Follow these steps to properly install the CAMEA and other Devices to the interface module. (CAMEA NOT INCLUDED) 1. Connect the 5-Pin Camera Power Cable to the module and use the ED and BLACK wires on this cable to power the rear-view camera. ED = +12V / BLACK = GOUND 2. Connect the 24-Pin AV Input/Output Cable to the Main Interface module. Connect the Camera and other Devices to the inputs on this cable. See labels on the cables for descriptions. The AV outputs can be used to go to an external monitor. Use the included 3.5 to CA cable for the audio out to your factory AUX IN. (Interface requires radio to be on AUX input Mode) 4 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

5 VCGM-80C ear View Integration Interface for Select OTHE CONNECTIONS: These steps will help you with using the additional connectors on the main 24-Pin Power Harness. 1. Plug the factory BLUE Mini USB to the black female USB of the VCGM-80C LVDS T-Harness. Insert the BLUE Mini USB of the VCGM-80C LVDS T-Harness to the factory HMI module. Connect the 6-Pin VCGM-80C LVDS T-Harness to the VCGM-80C Main Interface Module. NOTE ON CUE SYSTEMS: If display does not show video, reverse the ED and WHITE wires on the 6-Pin VCGM-80C LVDS T-Harness. 5 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

6 VCGM-80C ear View Integration Interface for Select 2. Connect the 2-Pin Switch Cable if you are looking to switch the sources using the included switch. Connect the I emote if you would like to extend the I Eye to a different location. POWEING THE MODULE AND OTHE FEATUES These steps will help you with connecting the loose wires. 1. Connect the ED power wire to the ACC +12V on the cigarette lighter. GOUND the black wire to your desired location. 2. Most of the loose wires are not required to be used. The most important wire to use is the GAY (reverse input). Connect the GAY wire to the reverse LAMP. You can also use the BLUE wire on this harness to enable the AV INPUTS. Connect the BLUE wire to GOUND. 6 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

7 VCGM-80C ear View Integration Interface for Select USING THE MENU OPTIONS ON I EMOTE These steps will help you with turning on certain features. Make sure the I receiver is in a clear view for the I emote to contact. 1. In order to access the Menus you must be in the AV source. Use the OK button on the I remote to switch sources (same function as momentary switch included). There are two menus on the interface. Use the arrows to navigate the menu. Press the MENU button on the emote to access the main menu. See options below. 2. To access the second menu set up, press and hold the left arrow for 3 seconds while in the AV source. This will bring you to a custom menu. Use the arrows to navigate the menu. Make sure the safe enable is set to ON. This is in case you are not using the BLUE loose wire on the harness. (Same function as BLUE wire) Use the arrows to navigate the menu. 7 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335

8 VCGM-80C ear View Integration Interface for Select Make sure the EA SELECT is set to LAMP; also make sure to connect the GAY wire to the EVESE LAMP wire. Use the arrows to navigate the menu. VEHICLE APPLICATIONS: BUICK La Crosse CADILLAC ATS CTS Coupe CTS/CTS V 2015 Escalade SX XTS CHEVOLET Avalanche Impala Malibu Silverado Suburban Tahoe GMC 2015 Canyon Sierra Pickup Yukon IntelliLink adio MyLink adio CUE adio 8 of 8 Crux Interfacing Solutions 6860 Canby Ave., Suite 116, eseda, CA 91335