Wi-Fi AUDIO/ VIDEO INTERFACE FOR SELECT CHRYSLER, DODGE & JEEP VEHICLES

Transcription

1 CHRYSLER /300C Aspen Sebring Town & Country DODGE Avenger Caliber Caravan Challenger Charger Dakota Durango Journey Nitro Ram JEEP Commander Compass Grand Cherokee Liberty Patriot Wrangler WORKS FOR: MyGig Radios Contact Tech Support for more information. VOLKSWAGEN Routan PARTS INCLUDED (1) CH-03M Interface Module (2) CH-03M 22-Pin T-Harness (1) Wi-Fi Interface Module (1) Wi-Fi 10-Pin A/V Harness (1) Wi-Fi Antenna (1) Instruction Sheet SAFETY PRECAUTIS 1. Please read through the entire instruction manual before starting any of the installation procedures. 2. We recommend disconnecting the negative side of the battery until ready to code the vehicle. 3. Do not install any of the main modules near any major components or near the HVAC system, as placing items near the HVAC may cause damage or overheating to the vehicle or interface. 4. We recommend not disconnecting any of the air bag connections behind the dash panels. 5. This product is under Crux s 1 year manufacturer s warranty. Warranty may be voided in the case where the device shows proof of being opened or improper extreme force. TECH SERVICES All our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems or if you have technical questions, contact us directly: Crux Interfacing Solutions Tech Support 1 (855) (Mon - Fri - 9:00 AM - 5:00 PM) Pacific Time Rev

2 INSTALLATI OVERVIEW WHITE 22-PIN 22-PIN (female plug) AUDIO/VIDEO OUTPUTS AUDIO/VIDEO INPUTS GRAY 22-PIN 22-PIN (female plug) GREEN/ VDO UNLOCK WHITE/ 12V OUTPUT RED/ 12V POWER 8-PIN BLACK/ GROUND DISABLE ENABLE OPTIAL/ TOGGLE SWITCH STATUS LED S DIP SWITCHES OVERVIEW Wi-Fi INTERFACE 10-PIN ACTIVATE VIDEO IN-MOTI DIP 1 = 2 3 OFF 4 5 = MAY VARY DIP 6 = MAY VARY Rev

3 CNECTING THE INTERFACE Follow these steps to properly install the interface module. Step 1 - Remove the factory radio to gain access to the factory WHITE and GRAY 22-Pin connectors. Disconnect the factory WHITE & GRAY 22-Pin connectors from the radio. Step 2 - Using the included WHITE and GRAY T-Harnesses, Connect the T-Harnesses to the headunit and to the factory harnesses. If the vehicle is not equipped with the WHITE harness, simply plug our WHITE T-Harness into the haedunit only. Rev

4 USING THE INTERFACE CNECTIS Follow these steps to properly install the interface module. Step 3 - The interface provides you with 1 Audio/Video Input and 1 Audio/Video Output. Use the A/V input on the WHITE 22-Pin T-Harness to input your device. Step 4 - Connect the 8-Pin connector on the provided T-Harness to the main interface module. Make sure all your connections are firmly inserted. Rev

5 CNECTING THE INTERFACE Follow these steps to properly install the interface module. Step 5 - After connecting the module, set the proper dip switches to the position. The interface requires DIP Switch 1 to be. Unless you are using the toggle switch option. The GREEN wire is used for the same function as DIP 1, but the non-permanent method. (See overview for Toggle Switch connection). ACTIVATE VIDEO IN-MOTI DIP 1 = 2 3 OFF 4 5 = MAY VARY DIP 6 = MAY VARY DIPS 5 & 6: These two dip switches control the CAN-Bus configuration. Switches 5 and 6 are defaulted to OFF, test the video in-motion, If there is no display on the screen while the vehicle is in motion, please place switches 5 and 6 to. DIP SWITCH DESCRIPTI Up =, Down = OFF DIP 1 = Video In-Motion (Always On) DIP 2 = Not Used DIP 3 = Not Used DIP 4 = Not Used DIP 5 = May Vary DIP 6 = May Vary LED INDICATORS BLUE LED: Blinking = No BUS Detected. Solid = BUS Recognized. OFF = Power Down/ Sleep mode. RED LED: = Power On OFF = Power OFF After each change of the DIP switch settings, we recommend powering down the module, then restarting the module. Rev

6 CNECTING THE Wi-Fi MODULE Using the included Wi-Fi interface module make the following connections as recommended. Step 1 - Connect the 10-Pin Harness to the Wi-Fi module. This cable will allow you the Audio/Video output for the vehicle. Use the AV inputs on the WHITE 22-Pin T-Harness to connect the Wi-Fi AV outputs. (See page 4 for details) Step 2 - The T-harness provides you a WHITE wire for 12V ACC to be used on the Wi-Fi module. Connect the RED wire from the 10-Pin Wi-Fi harness to the WHITE wire coming off the T-harness. For the best signal we recommend GROUNDING the Wi-Fi module near the module. (Connect the BLACK wire from the Wi-Fi harness to the BLACK wire on the 8-Pin connector) See below. GREEN/ VDO UNLOCK WHITE/ 12V OUTPUT RED/ 12V POWER 8-PIN BLACK/ GROUND DISABLE ENABLE OPTIAL/ TOGGLE SWITCH STATUS LED S Wi-Fi INTERFACE 10-PIN ACTIVATE Rev

7 CNECTING YOUR DEVICE TO THE Wi-Fi MODULE Preliminary: Connect the Wi-Fi Antenna to the Wi-Fi module to power the signal. Step 3 - With the Wi-Fi module powered on, use the MODE button to toggle/select between the ios system setup and the Android system setup. Make sure the radio is on the AUX Source to view the factory AV input. (See below) Note: The USB port can be used as a 5V output/ charger for most devices. To select the A/V Input source: Press the MEDIA button to see new menu, then select VES. HDD DISC AUX VES Make note that the interface is Defaulted to Miracast (Android), make sure the system you have is highlighted. Blue AirPlay Icon = ios (iphone) Green Miracast = Miracast (Android) Rev

8 CNECTING YOUR DEVICE TO THE Wi-Fi MODULE On the new ios 7 you can easily do the following: Swipe your finger from the bottom up on the iphone or ipad. From the Quick Menu turn the Wi-Fi and connect to Hot Spot. After connecting the Wi-Fi, from that same screen select the Air-Play item to connect to the interface. To turn on Mirroring, you will need to be connected to the interface and select the Air-Play item again, and turn on Mirroring option. If your device doesn t support the ios 7: 1. Settings > Wi-Fi > On 2. Choose Network > Hot Spot 3. After connected, double click the Home button to display your recently used apps. 4. Select the Air-Play icon to begin to mirror. (Wi-Fi must be connected). From your the Home screen: Swipe down from the top of the screen to access the Screen Mirroring Scan for the Hot Spot device. This can take up to 20 seconds. Connect and begin streaming. MIRRORING YOUR DEVICE The Mirroring connection uses a direct Wi-Fi connection to transfer the Audio and Video from your device. This does not require a active network. If your Smartphone has the Screen Time Out active on your phone, and your phone display goes to sleep, you will no longer see the image on the screen. Deactivate to avoid. If no Air-Play icon is present, make sure your connected to Hot Spot. When casting MUSIC to the Wi-Fi interface, the Album art will be shown along with song information as: Time - Artist - Album - Track. If there is no album art present the image below is what you will see, along with the song information. Rev

9 COMPATIBLE RADIO: MyGig Radio Rev