SERVICE SPECIFICATION SU-4586
|
|
- Madeline Porter
- 5 years ago
- Views:
Transcription
1 SERVCE SPECFCATON SU-4586 STYLE F-70 NVERTER- DRVER UN45l General This service specification covers the testing and maintenance procedures for the Style F-70 nverter-driver The F-70 supplies square wave power at a stable frequency to the F-50 nverter-follower 2 General Equipment Specifications The general equipment specifications are as follows: a nput 16 VDC ±5% at 50 ma b Output "t ' 18 Volts Square Wave (36 volts peak to peak) into 3000 ohms (approximately 100 milliwatts) Frequency 94 8 ± 0 2 HZ* c Temperature Range *HERTZ - Cycles/sec Definition adopted by EEE on Oct 14, 1965 PRNTED N USA Bl UNON SWTCH & SGNAL DVSON Westinghouse Air Brake Company PTSBURGH, PA April, 1967
2 3 Maintenance The following instruments are required for checking the waveform, voltage and frequency outputs of the F-70 nverter-driver Use DC Measurement AC Waveforms AC Voltage (Sine Wave Only) Test nstrument Simpson Model 260 or equivalent Tektronix 515, or any good quality, general purpose oscilloscope Hewlett Packard 400D or equivalent VTVM l The F-70 is adjusted at the factory and does not require field adjustment, However, should a change be made of any component in the oscillator circuit, the amplitude and wave shape at the emitter of Q3 should be checked There should be a sine wave voltage of volts RMS ±25% amplitude Crossover points should have equal time base (refer to figure 4a) Should the proper voltage not be present, R4 will have to be changed as follows: a Connect a decade box in place of R4 and connect a VTVM and an oscilloscope from the emitter of Q3 to -16 R b Vary the decade box until the proper voltage appears The typical value for R4 is 30, 000 ohms so the decade box range necessary should be between 20, 000 and 39, 000 ohms c Note value shown on decade box and replace R4 with a resistor of like value (See note on figure 2 ) d After replacing R4 check for proper voltage on the oscilloscope keeping in mind that because of the cumulative tolerance allowances of the decade box and the resistor being used, R4 may not be quite what is necessary to balance the feedback circuit f clipping and distortion occur with an amplitude greater than 2 5 volts, R4 is too low f the amplitude is less than 5 volts, R4 is too high Make the final substitution as necessary to achieve the desired results Parts locations are shown in figures 1 and 2 Figure 3 is the schematic diagram Figure 4 contains voltage waveshapes and values that will aid in troubleshooting the equipment SU-4586, p 2
3 4 Parts List Reference Designation Part Number Description 1 UM Board, Term Bl UJ Lamp, :/f:1860 Cl, C4 UJ Capacitor, 47 µf - 20V C2 UJ Capacitor, 500µf - 25V C3, C6 UJ Capacitor, 4 7 µf - 35V C5 UJ Capacitor, 33 µf - loov C7 UJ Capacitor, 10 µf - 20V C8 UJ Capacitor, 33 µf - 20V C9 UJ Capacitor, looµf - 20V Dl UJ Diode, 1N34AS D2, 3, 4, 5 UJ Diode, 1N456 D6 UJ Diode, Zener 1N2979B Ql, 2, 3, 4, 5, 6, 7 UJ Transistor, 2N2270 R, Rl2 UJ Resistor, 2 2K R2, 6, 7, 8 UJ Resistor, 1 OK R3 UJ Resistor, 3 9K R4 UJ Resistor, 30K R5 UJ Resistor, 820 R9 UJ Resistor, 6 8K RO UJ Resistor, 150 Rll UJ Resistor, 1 5K R13 UJ Resistor, 620 R14 UJ Resistor, 62 R15, Rl8 UJ Resistor, 3 OK R16 UJ Resistor, 300 Rl7 UJ Resistor, 51K R19 UJ Resistor, 33 REO UJ Reed, Encoder Tl UN Transformer r SU-4586, p 3
4 WABCC 0 0 )----t+ C2 C5 + c, d 6' CJ3 -i "\ '«:! ' -; 7' 0 0 ) 6" ) Figure 1 Component Board, Side A SU-4586, p 4
5 NOTE: f necessary, to provide proper value of R4, remove jumper between R4 and C3 and insert necessary additional resistance "JJ rn - 0 Figure 2 Component Board, Side B SU-4586, p 5/6
6 "
7 ,, TRAN515TOR '2N2210 LEAt> ARR ANG EMEt-11" + f- 1 C 41 'e \"'-_'-><''/ '---+" REOqll RO 150 f{:v J 8 Rl3i!Rl5 <o10 3K \ ' 4J j "- u<;;> 11 A '22K - R\1 5\K D4- l ---r D$!l_ C' C2, 500 td lu9 /\V\,-- + GU 3? "' J'T'\ 81 R Rl4 RG, R8 D < \ SK D2 " \Z Bu '2 z \ -l"r Figure 3 Schematic Diagram SU-4586, p 7 /8
8 WAECC A B c ' ' L - - J '\ 'P'1a' ''14 EMTTER Q3 V /DV VERT BASE Q4 0 5V /DV VERT COLL Q5 0 5V /DV VERT M SEC/DV HOR M SEC/ DV HOR M SEC/ DV HOR D E F fo fo - BASE Q6 0 5V /DV VERT BASE Q7 5V/DV VERT OUTPUT lov /DV VERT 2M SEC/DV HOR 2M SEC/DV HOR 1Z-2Z 2M SEC/DV HOR "' i Note: All voltages are referenced to -16R DC VOLTAGE MEAS ±5% USNG SMPSON MODEL 260 OR EQUVALENT DC V-0-M REED N CRCUT & OSCLLATNG REED NOT N CRCUT - NOT OSCLLATNG BASE EMTTER Q 20 Q2 42 Q3 74 Q4 62 Q5 7 Q6 0 Q7 74 Q O Q2 6 6 Q3 60 Q4 5 Q5 7 Q6 0 Q7 0 COLLECTOR Figure 4 Waveforms and Voltages, Tektronix 515 SU-4586, p 9/10
INSTRUCTION PAMPHLET U-5824
NSTRUCTON PAMPHLET U-5824 WABCO / STYLE SS-1 OVERSPEED DETECTOR * * * * * * * * * NTRODUCTON The SS-1 Overspeed Detector is an electronic device used in conjunction with cab signal equipment to provide
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 5 ZENER DIODE VOLTAGE REGULATOR, DIODE CLIPPERS AND CLAMPERS OBJECTIVES The purpose of this experiment
More informationExperiment #4: Solid State Diodes Applications III
SCHOOL OF ENGINEERING AND APPLIED SCIENCE DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING ECE 2115: ENGINEERING ELECTRONICS LABORATORY Experiment #4: Solid State Diodes Applications III COMPONENTS Type
More informationClick on the SwCAD III shortcut created by the software installation.
LTSpice Guide Click on the SwCAD III shortcut created by the software installation. Select File and New Schematic. Add a component Add a resistor Press R or click the resistor button to insert a resistor.
More informationSupertex inc. HV9922DB2. Offline, Non-Isolated, 23V, 45mA Auxiliary Power Supply. General Description. Specifications
Offline, Non-Isolated, 23V, 45mA Auxiliary Power Supply General Description The is a universal input, offline, non-isolated auxiliary power supply using Supertex s HV9922 constant current switching regulator
More informationCHAPTER 5. Voltage Regulator
CHAPTER 5 Voltage Regulator In your robot, the energy is derived from batteries. Specifically, there are two sets of batteries wired up to act as voltage sources; a 9V battery, and two 1.5V batteries in
More informationCopyright 2014, R. Eckweiler & OCARC, Inc. Page 1 of 6
HOM rev. new Heathkit of the Month: by Bob Eckweiler, AF6C Heathkit of the Month #52 - SK-211 AC Monitor Heathkit SK-211 AC Monitor Introduction: When club president, Nicholas - AF6CF, mentioned he had
More informationModel INSTRUCTION MANUAL DIGITAL MULTIMETER
Model 57040 INSTRUCTION MANUAL DIGITAL MULTIMETER SAFETY INFORMATION This multimeter has been designed according to IEC 1010 concerning electronic measuring instruments with an overvoltage category (CAT
More informationFluke 43B. Power Quality Analyzer. Getting Started. EN June Fluke Corporation, All rights reserved. Printed in The Netherlands.
Power Quality Analyzer EN June 2005 2001-2005 Fluke Corporation, All rights reserved. Printed in The Netherlands. All product names are trademarks of their respective companies. PLACING ORDERS AND GETTING
More informationDiode IV Characteristics
Diode V Characteristics Breakdown region Reverse Bias 1mA Forward Bias Diode Symbol 0.7V V n forward bias operation, the diode will not conduct significant current until the voltage reaches about 0.7V.
More informationMANUAL FOR THE UNIVERSAL MANUAL CONTROLLER UMC - 31
MANUAL FOR THE UNIVERSAL MANUAL CONTROLLER UMC - 31 PPS PART NO. 133550 DRAWING NO. 133550-10 THIS MANUAL ASSIGNED TO THE S/N: THE INFORMATION CONTAINED IN THIS MANUAL IS PROPRIETARY TO PACIFIC POWER SOURCE,
More informationOWNER S MANUAL. Dynasty Maxstar 280 Dynasty Maxstar 210 Modbus Expansion. 1. Software Expansion OM D
OWNER S MANUAL OM-265 415D 2015 07 Dynasty Maxstar 280 Dynasty Maxstar 210 Modbus Expansion Read and follow the power source Owner s Manual and labels carefully before installing, operating, or servicing
More informationDEV-1 HamStack Development Board
Sierra Radio Systems DEV-1 HamStack Development Board Reference Manual Version 1.0 Contents Introduction Hardware Compiler overview Program structure Code examples Sample projects For more information,
More informationInfrared Add-On Module for Line Following Robot
1 Infrared Add-On Module for Line Following Robot January 3, 2015 Jeffrey La Favre The infrared add-on module allows multiple line following robots to operate on the same track by preventing collisions
More informationD115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors
D115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors Ron Boe 5/15/2014 This user guide details the servo drives capabilities and physical interfaces. Users will be able to
More informationElectronic Devices. Special Purpose Diodes. Chapter Three. Dr. Hisham Alrawashdeh
Electronic Devices Chapter Three Special Purpose Diodes Dr. Hisham Alrawashdeh Chapter Three Special Purpose Diodes Introduction Chapter 2 was devoted to general-purpose and rectifier diodes, which are
More informationState of New York. Model 242-NY. DC Isolator Unit Operations Manual THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE MODEL 242-NY DC ISOLATOR UNIT.
State of New York Model 242-NY DC Isolator Unit THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE MODEL 242-NY DC ISOLATOR UNIT. SERIAL NUMBER: 0601XXXXX and up PCB Issue B, 010-0242-001 REVISION: APRIL
More informationCentral-I Family. CiG1-AMP01-1A-01-00
Central-I Family CiG1-AMP01-1A-01-00 Hardware User's Manual Central-ICentral-I - Hardware Manual -Amplifier CiG1-AMP01- Page 1 Revision control table Version Description Date 1.0 Initial (based on Hardware
More informationI UNION SWITCH & SIGNAL I [m] SERVICE MANUAL 6176 A member of the ANSALOO Group 5800 Corporate Drive. Pittsburgh, PA 15237
UNON SWTCH & SGNAL [m] SERVCE MANUAL 6176 A member of the ANSALOO Group 5800 Corporate Drive. Pittsburgh, PA 15237 nstallation, Operation, and Maintenance CAB SGNAL VTAL TME DELAY UNT N451489-9001 N451489-9002
More informationCentral-I Family. CiG1-AMP01-1A-01-00
Date: Sunday, Aug14, 2016 Version: 1.16 Central-I Family CiG1-AMP01-1A-01-00 Hardware User's Manual Page 1 Date: Sunday, Aug14, 2016 Version: 1.16 Revision control table Version Description Date 1.0 Initial
More informationBG1B Universal Gate Drive Prototype Board
BG1B Universal Gate Drive Prototype Board Description: The BG1B is a single channel gate drive circuit board for high power IGBT modules. The BG1B utilizes Powerex hybrid gate drivers and DC-to-DC converters
More informationBasic Electrical Measurements
Page 1 of 11 Introduction Basic Electrical Measurements This Lab introduces the five basic, lumped circuit components or element models Resistor, Capacitor, Inductor, Voltage Source, Current Source. Also
More informationEMCP 4.4 Simulator Manual. Author: Lucas Tolbert CIC Engineering 345 Center Street East Peoria, IL
EMCP 4.4 Simulator Manual Author: Lucas Tolbert CIC Engineering 345 Center Street East Peoria, IL Date of Origin: 11/23/2010 Overview This document will detail the features and operation of the EMCP 4.4
More informationBENCHMARK MEDIA SYSTEMS, INC.
BENCHMARK MEDIA SYSTEMS, INC. RLY-106 Instruction Manual 1.0 Introduction...1 2.0 Input and Output Connections...1 2.1 Connection Alternatives...2 3.0 Relay Ratings...2 4.0 Applications...4 4.1 Audio Signal
More informationANNA UNIVERSITY QB ( )
ANNA UNIVERSITY QB (2003--2008) UNIT I POWER SEMICONDUCTOR DEVICES PART A 1. Draw the V-I characteristics of SCR and mark the holding current and latching current in the characteristics. Nov/Dec04 2. What
More informationELECTRONICS TESTING SOLUTIONS
ELECTRONICS TESTING SOLUTIONS THE BEST TOOLS FOR YOUR BENCH Research & Development Industrial Labs PCB & Circuit Board Analysis CHOOSE YOUR BENCHTOP TESTING SOLUTION If you re trying to find the right
More informationDept. of Computer Science and Engineering
Dept. of Computer Science and Engineering EECS 2210 Electronic Circuits and Devices Project Report Power Supply for a Mobile Charger Submitted by : Linda Chigbo Ariel Laboriante Ege Arslan Date 4/17/2015
More information2. Control Pin Functions and Applications
IMARY CONTROL ( PIN) Module Enable / Disable. The module can be disabled by pulling the below 2.3 V with respect to the Input. This should be done with an open-collector transistor, relay, or optocoupler.
More informationLecture (05) PN Diode. Special Purpose diodes
Lecture (05) PN Diode applications III, Special Purpose diodes By: Dr. Ahmed ElShafee ١ Agenda Diode limiters Diode Clampers Zener Diode Zener Diode Applications ٢ Diode limiters Figure shows a diode positive
More informationMODULES FOR SAFETY AND MONITORING
MODULES FOR SAFETY AND MONITORING Woertz AG Hofackerstrasse 47, P.O. Box 948, CH-43 Muttenz, Switzerland Tel. ++4 6 / 466 33 33, Fax ++4 6 / 46 96 06 http://www.woertz.ch Woertz-USA 5 Discovery Drive,
More informationCheckSum. FUNC-2B Functional Test Module. The FUNC-2B features:
CheckSum FUNC-2B Functional Test Module FUNC-2B Functional Test Module Made in U.S.A. The CheckSum Model FUNC-2B Functional Test System is designed to be used as an extension to a CheckSum ICT System.
More informationSKEE 2742 BASIC ELECTRONICS LAB
Faculty: Subject Subject Code : SKEE 2742 FACULTY OF ELECTRICAL ENGINEERING : 2 ND YEAR ELECTRONIC DESIGN LABORATORY Review Release Date Last Amendment Procedure Number : 1 : 2013 : 2013 : PK-UTM-FKE-(0)-10
More informationModel R5005. Instruction Manual. True RMS Industrial Multimeter. reedinstruments. www. com
Model R5005 True RMS Industrial Multimeter Instruction Manual reedinstruments com Table of Contents Safety... 4 Features... 5 Specifications...5-6 Instrument Description...7-8 Operating Instructions...9-13
More informationAC/DC TRUE RMS CLAMP METER ACM-2036
AC/DC TRUE RMS CLAMP METER ACM-2036 User s Manual Safety International Safety Symbols This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for further information.
More informationSoloist Linear Series
Soloist Linear Series Position Controller and Servo Amplifier Linear Single axis digital servo controller with integral power supply and amplifier Advanced software architecture shortens customer development
More informationTINA-TI Simulation Software. Application Note
TINA-TI Simulation Software Application Note Phil Jaworski Design Team 6 11/16/2012 Abstract TINA-TI is a circuit design and simulation tool created by both Texas Instruments and DesignSoft that has helped
More informationTSXCCY1128 electronic cam module cams - 1 axis - 7 W
Characteristics electronic cam module - 128 cams - 1 axis - 7 W Main Range of product Product or component type Number of cams 128 Number of tracks 32 Function of module I/O modularity Modicon Premium
More informationPSU. User s manual. Rev. 0
PSU User s manual Rev. 0 2010 1 This user manual is for the standard version of the converter. All information in this user manual, including methods, techniques and concepts described herein, are proprietary
More informationOPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER
OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER SAFETY INFORMATION This multimeter has been designed according to IEC 1010 concerning electronic measuring instruments with an overvoltage category (CATⅡ)
More informationSIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR (AUTONOMOUS) Siddharth Nagar, Narayanavanam Road QUESTION BANK (DESCRIPTIVE) UNIT I
QUESTION BANK 2017 SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR (AUTONOMOUS) Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : Basic Electronic Devices (16EC401) Year
More informationac wave 2 supply ( analog device )
ac wave 2 supply ( analog device ) «SPECIFIC PRODUCT SECTION» Instruction and user s manual Release 2.1 00/05 REEL S.r.l. Electronic Power Drives Via Riviera Berica, 42 36024 Ponte di Nanto - Vicenza -
More informationSORDS ELECTRIC ~ MA7200. Sensorless Vector AC Inverter.
www.sordselectric.com MA7200 Sensorless Vector AC Inverter Features and Benefits Sensorless Vector The MA7200 has precise speed and torque control for the most demanding system performance and simple set-up
More informationPSU User s manual Rev. 0 January
PSU User s manual Rev. 0 January 2011 1 This user manual is for the standard version of the converter. All information in this user manual, including methods, techniques and concepts described herein,
More informationPower Supply Transient Protection for MNA and VNA Amplifiers (AN )
Power Supply Transient Protection for MNA and VNA Amplifiers (AN-60-027) Introduction Shorting of the DC voltage terminal of a MMIC amplifier to ground while DC power is connected can cause permanent damage
More informationPIECAL CALIBRATORS. Milliamp Thermocouple RTD Voltage Frequency.
PIECAL CALIBRATORS Milliamp Thermocouple RTD Voltage Frequency www.piecal.com Accurate - Exceeds Expectations Reliable - Three Year Warranty Troubleshoot Loops - Automatic Diagnostics NIST Traceable -
More informationDigital Frequency Divider INSTRUCTION MANUAL CONTENTS. 1. Working Principle Installation Setting Up Technical Data 4.
Digital Frequency Divider INSTRUCTION MANUAL CONTENTS 1. Working Principle 2 2. Installation 2 3. Setting Up 3 4. Technical Data 4 Code: 189/1a 1 WORKING PRINCIPLE The DFD has been designed to generate
More informationType MVTT 14 and MVTT 15: Static Digital Time delay relays
Type MVTT 4 and MVTT 5: Static Digital Time delay relays Features 000/ setting range Time settings easily selected by means of thumbwheel switches Provide time delayed pick-up, or drop-off Compact construction
More informationThe International Power Quality Resource
3-Phase Reactors Line/Load Reactors Increase Drive System Reliability Filter Power Line Disturbances Reduce Harmonics Reduce Surge Currents Reduce dv/dt Extend Transistor Life Reduce Motor Noise and Temperature
More informationExclusive 2.5 GHz Frequency Counter
Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory
More informationModel R5010. Instruction Manual. TRMS Digital Multimeter. reedinstruments www.
Model R5010 TRMS Digital Multimeter Instruction Manual reedinstruments www com Table of Contents Safety...3-4 Features... 5 Specifications...5-8 Instrument Description...8-9 Operating Instructions...10-16
More informationHypot III. Graphic Liquid Crystal Display. 10 Memories with 3 Steps per Memory. Low Limit Detection System. SmartGFI Circuit (Patent Pending)
Hypot III DIELECTRIC WITHSTAND TESTERS For Production Line Safety Agency Compliance Testing Graphic Liquid Crystal Display 10 Memories with 3 Steps per Memory Low Limit Detection System 3605 AC Hipot SmartGFI
More informationECE 2010 Laboratory # 2 J.P.O Rourke
ECE 2010 Laboratory # 2 J.P.O Rourke Prelab: Simulate all the circuits in this Laboratory. Use the simulated results to fill in all the switch control tables in each part. Your Prelab is due at the beginning
More informationIDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-609 The Service Information provides the following information: Precautions
More informationLNX Series Motor and Drives
LNX Series Motor and Drives Operator's Manual PN 04-01808 x PRECISION MOTION CONTROLS 2530 Berryessa Rd. #209 San Jose, CA 95132 1 2 Table of Contents Page Introduction 1. Description 3 2. Warranty 4 Installation
More informationDisplays Transducers. Displays and transducers
JJ Displays JJ Transducers Displays and transducers DS_Displays_and_transducers 06/2016 225 Displays and transducers Our electronic devices for flow and volume measurement are suitable for all SIKA flow
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More informationSEMICONDUCTOR GENERAL DATA
MOTOROLA SEMICONDUCTOR TECHNICAL DATA 0 mw DO-35 Glass Zener Voltage Regulator Diodes GENERAL DATA APPLICABLE TO ALL SERIES IN THIS GROUP 0 Milliwatt Hermetically Sealed Glass Silicon Zener Diodes Specification
More informationPCD M02/MPD 001. Operation Manual
PCD M02/MPD 001 Miniature Multi-Channel Piezoelectric Actuator Driver Card With or without Integrated PolaRITE III Polarization Controller Operation Manual Version 1.3 October 30, 2015 General Photonics
More informationBG2D Solderless Connection Gate Drive Prototype Board
Application NOTES: First Release: May, 2008 BG2D Solderless Connection Gate Drive Prototype Board Description: The BG2D is a two channel gate drive circuit for that the dual NX series modules pins plug
More informationMetal Oxide Varistor (MOV) Data Sheet
Metal Oxide Varistor (MOV) Data Sheet Features Wide operating voltage (V ma ) range from 8V to 800V Fast responding to transient over-voltage Large absorbing transient energy capability Low clamping ratio
More informationDiodes Zener diodes. Electronics Diodes. Terry Sturtevant. Wilfrid Laurier University. September 9, 2015
Electronics Diodes Wilfrid Laurier University September 9, 2015 Diode an electronic device which passes current in one direction only Diode an electronic device which passes current in one direction only
More informationLDD M SERIES INSTRUCTION MANUAL LDD M SERIES
TM LDD M SERIES LDD M SERIES INSTRUCTION MANUAL P O Box Bozeman, MT 9 Phone (0) -90 Fax (0) -9 email sales@wavelengthelectronics.com www.wavelengthelectronics.com TABLE OF CONTENTS Features... Customer
More informationZener diodes have a zener voltage (avalanche or breakdown voltage) in the range of 3 V to 200 V as
Exercise 2: EXERCISE OBJECTIVE When you have completed this exercise, you will be able to demonstrate the operation of a zener diode by using a dc characteristic curve. You will verify your results with
More informationPhysics 120/220 Lab Equipment, Hints & Tips
Physics 120/220 Lab Equipment, Hints & Tips Solderless Breadboard... 2 Power supply... 4 Multimeters... 5 Function generator... 5 Oscilloscope... 6 10X probe... 7 Resistor color code... 7 Components...
More informationIELR Rail-Mount Series Magnetic Circuit Protectors
IELR Rail-Mount IELR Rail-Mount Series Magnetic Circuit Protectors Introduction 92 Single Pole 93 Specifications 94 Operating Characteristics 95 Delay Curves 96 Approvals & Decision Tables 200 IELR Series
More informationProduct Manual Amp Current Sensor AC/DC
Product Manual 1122-30 Amp Current Sensor AC/DC Phidgets 1122 - Product Manual For Board Revision 0 Phidgets Inc. 2009 Contents 4 Product Features 4 Connections 4 Type of Measurement 5 Getting Started
More informationTSXCTY2A 2 channels counter modules - 40 khz - 30 ma at 24 V DC, 280 ma at 5 V DC
Characteristics 2 channels counter modules - 40 khz - 30 ma at 24 V DC, 280 ma at 5 V DC Main Range of product Product or component type I/O modularity Mar 05, 2018 Modicon Premium Automation platform
More informationTEXAS INSTRUMENTS ANALOG UNIVERSITY PROGRAM DESIGN CONTEST MIXED SIGNAL TEST INTERFACE CHRISTOPHER EDMONDS, DANIEL KEESE, RICHARD PRZYBYLA SCHOOL OF
TEXASINSTRUMENTSANALOGUNIVERSITYPROGRAMDESIGNCONTEST MIXED SIGNALTESTINTERFACE CHRISTOPHEREDMONDS,DANIELKEESE,RICHARDPRZYBYLA SCHOOLOFELECTRICALENGINEERINGANDCOMPUTERSCIENCE OREGONSTATEUNIVERSITY I. PROJECT
More informationAUTOMOTIVE MICRO-ISO RELAY FEATURES
AUTOMOTIVE MICRO-ISO RELAY RELAYS...... Compliance with RoHS Directive FEATURES Micro-ISO type terminals Small size: mm(l) mm(w) mm(h). inch(l). inch(l). inch(h) Wide line-up PC board and, Resistor and
More informationNdrive Linear Series. Digital Servo Amplifiers Linear. Output power range of 10 or 20 A peak with ±10 to ±80 VDC bus
Ndrive Linear Amplifiers/Drives Ndrive Linear Series Digital Servo Amplifiers Linear Output power range of 10 or 20 A peak with ±10 to ±80 VDC bus 2- or 3-phase AC line input or DC input CE approved and
More informationDIGITAL PANEL METERS
DIGITAL PANEL METERS 3 1/2 digit,4 1/2 digit - A/C D/C Voltage/Current 3 1/2 digit4 1/2 digit- AC/DCVoltage/Current-TRMS DPM U AC/DC VOLTAGE / CURRENT 3 1/2 DIGIT - MODEL : PE 3000 4 1/2 DIGIT - MODEL
More informationSOUTHERN POLYTECHNIC S. U.
SOUTHERN POLYTECHNIC S. U. ECET 1012 Laboratory Exercise #4 ELECTRICAL & COMPUTER ENGINEERING TECHNOLOGY Introduction to PSpice Name Lab Section Date Overview: This laboratory experiment introduces the
More informationModel Number Structure
Solid State Relays with Failure Detection Function G3PC CSM_G3PC_DS_E_1_1 Refer to Safety Precautions for All Solid State Relays. Detects failures in SSR used for heater temperature control and simultaneously
More informationCompensation Range (pf.):
Pomona s latest design of Passive Oscilloscope probes feature a one piece (monolithic) design for robust probe life. Probe bandwidth ratings are specified as a system bandwidth. System bandwidth includes
More informationADDJOG User Guide 7/30/10. Overview
ADDJOG User Guide 7/30/10 Overview The ADDJOG is a PLC expansion board used to add digital inputs and outputs to a compatible host PLC. The ADDJOG has 64 open collector outputs and 64 non-isolated inputs.
More informationEasy To Use OEMS Take Note
MA7200 Features Sensorless Vector Precise speed and torque control for the most demanding system performance. Simple set-up through autotuning function. The MA7200 can be operated in sensorless vector
More informationMaxim Integrated Products 1
19-3717; Rev 1; 11/05 MAX1179 Evaluation Kit General Description The MAX1179 evaluation kit (EV kit) is an assembled and tested circuit board that demonstrates the MAX1179 analog-to-digital converter.
More informationicex-cmtm General specs and Installation guide
icex-cmtm General specs and Installation guide 1. General view 2. Specifications 2.1. Common specs: Ethernet 1 x 10/100Base/T, RJ45 connector with traffic and link LED Serial Interface 1 x RS232/485 USB
More informationIELR Series
IELR Series Rail-Mount Magnetic Circuit Protectors Introduction Poles Specifications Operating Characteristics Delay Curves Approvals Decision Tables 6 62 63 64 65 69 70 IELR Series Rail-Mount Hydraulic
More informationAG300 Family CTL01-3A-03, AMP01-2A-02
AG300 Family CTL01-3A-03, AMP01-2A-02 Hardware User's Manual Page 1 Revision control table Version Description Date 1.0 Initial (based on Hardware Manual of previous hardware versions) April 27, 2016 1.1
More informationMAINTENANCE MANUAL KG 102 DIRECTIONAL GYRO
MAINTENANCE MANUAL KG 102 DIRECTIONAL GYRO MANUAL NUMBER 006-15622-0007 REVISION 7 MARCH, 2002 WARNING Prior to the export of this document, review for export license requirement is needed. COPYRIGHT NOTICE
More informationPage Housing Plastic Metal Mounting DIN Rail or surface mount Panel or bracket mount Wattage Range 10W to 240W 7.5W to 240W 10W to 300W
Selection Guide Selection Guide PS5R Slim Line PS5R PS3L Operator Interfaces Communication & Networking PLCs NEW Models Appearance Automation Software Page 107 113 118 Housing Plastic Metal Mounting DIN
More informationMODEL 42 PUSHBUTTON DIAL
ITT Practices SECTION 55 042 117 Issue 1, Oct. 1984 MODEL 42 PUSHBUTTON DIAL CONTENTS PAGE 1. INTRODUCTION... 1 2. GENERAL DESCRIPTION............ 1 3. REMOVAL... 3 4. DiSASSEMBLy... 3 5. REPLACEMENT PARTS..............
More informationQUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1350 HIGH TEMP ADC
LTC2246H, LTC2226H DESCRIPTION Demonstration circuit 1350 supports a family of 12 and 14-Bit 25Msps ADC. This assembly features one of the following devices: LTC2226H or LTC2246H high speed, high dynamic
More information14H SERIES. Metal Oxide Varistor (MOV) Data Sheet. Features. Applications. Part Number Code
Metal Oxide Varistor (MOV) Data Sheet Features Wide operating voltage (V 1mA ) range from 18V to 1800V Fast responding to transient over-voltage Large absorbing transient energy capability Low clamping
More informationPERFORMANCE SPECIFICATION SHEET
PERFORMANCE SPECIFICATION SHEET INCH-POUND w/amendment 1 22 September 2005 SUPERSEDING MIL-PRF-39016/19G 1 April 2005 RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, DPDT, LOW LEVEL TO 1 AMPERE WITH
More informationIDEAL INDUSTRIES INC. TECHNICAL MANUAL MODEL:
IDEAL INDUSTRIES INC. TECHNICAL MANUAL MODEL: 61-795 The Service Information provides the following: Precautions and safety information Specifications Performance test procedure Calibration and calibration
More informationTHIS IS A GUIDE LISTING
Tektronix 067-0521-00 Calibration Fixture Tektronix 067-0521-01 Calibration Fixture Tektronix 067-0523-00 Type 84 Plug-In Test Unit Tektronix 067-0540-00 Calibration Fixture Tektronix 10A2 Dual Trace Amplifier
More informationPACSystems RX3i and Series IC694MDL916 and IC693MDL916 Output Module, Isolated Relay, N.O., 4 Amp, 16 Point
January 2010 PACSystems RX3i and Series 90-30 IC694MDL916 and IC693MDL916 Output Module, Isolated Relay, N.O., 4 Amp, 16 Point 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 TB IC694MDL916 Q1 Q2 Q3 Q4 Q5 Q6 Q7
More information3A SERIES MODULAR AC & DC LOADS
3A SERIES MODULAR AC&DC LOADS Key features: Max. Power 300VA per Module Available Voltage Ranges: 60V, 150V and 300 V AC or DC Max. Current Range 20 A AC or DC Choice of Three Modules Up to 4 Load Inputs
More informationIRCS2277S Demo Board
Demo Board Up to 1200V DC-bus capability IR2277S device connected for 3-phase current sensing Open drain PWM output (PO) Open drain Over Current output (OC) Ratiometric analog output for A/D converters
More informationVector Drive - Troubleshooting Guide
Haas Technical Documentation Vector Drive - Troubleshooting Guide Scan code to get the latest version of this document Translation Available The Haas Vector drive is the source of power for the spindle
More informationOperating Instructions. For. Level Control Module. Model SSR 1000
Operating Instructions For Level Control Module Model SSR 1000 SSR Operation Instructions Rev. 1 Jan 01 Page 1/7 1. Note Please read and take note of these operating instructions before unpacking and commissioning.
More informationCompensation Range (pf.):
Pomona s latest design of Passive Oscilloscope probes feature a one piece (monolithic) design for robust probe life. Probe bandwidth ratings are specified as a system bandwidth. System bandwidth includes
More information+Denotes lead-free and RoHS-compliant
19-0997; Rev 0; 9/07 MAX4208 Evaluation Kit General Description The MAX4208 evaluation kit (EV kit) simplifies evaluation of the MAX4208 ultra-low offset/drift, adjustable gain, precision instrumentation
More informationNATIONAL CERTIFICATE (VOCATIONAL) ELECTRONIC CONTROL AND DIGITAL ELECTRONICS NQF LEVEL 3 NOVEMBER 2010
NATIONAL CERTIFICATE (VOCATIONAL) ELECTRONIC CONTROL AND DIGITAL ELECTRONICS NQF LEVEL 3 NOVEMBER 2010 (12041023) 22 October (Y-Paper) 13:00 16:00 This question paper consists of 6 pages. (12041023) -2-
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. TESTING LOW PROFILE 2 FORM C RELAY TQ RELAYS 9.354 26.7 +.4 1.51 5.2 +.16.8
More informationMS2115B Dual Display Digital Clamp Meter Operation Manual ZERO MIN RANGE HOLD
MS2115B Dual Display Digital Clamp Meter Operation Manual REL MAX B.L ZERO MIN RANGE HOLD B CONTENTS 1. Safety Information...1 1.1 Preparation...1 1.2 Usage...2 1.3 Mark...3 1.4 Maintenance...4 2. Description...4
More informationDigital ac/dc (24V) Input Module
Installation Instructions Digital ac/dc (24V) Input Module Catalog Number 1771-IND, Series C Topic Page Important User Information 2 Before You Begin 3 Power Requirements 3 Prevent Electrostatic Discharge
More informationNCP107X, 12 Vout, Off-line Buck Regulator
Design Note DN05058/D NCP107X, 12 Vout, Off-line Buck Regulator Device Application Input Voltage Output Power Topology I/O Isolation NCP1071 NCP1075 NCP1077 Smart Meters Electric Meters, White Goods 85
More information