Solution. Installation Manual. Tone & Visual Nurse Call System. N56W24720 N. Corporate Circle Sussex, WI

Transcription

1 Solution Installation Manual Tone & Visual Nurse Call System Made in the USA 3 Year Warranty N56W24720 N. Corporate Circle Sussex, WI RP8500SCNC Ver. 1 05/17

2 Thank you for purchasing Rath s SmartCare Solution. We are the largest Emergency Communication Manufacturer in North America and have been in business for over 35 years. We take great pride in our products, service, and support. Our Emergency Products are of the highest quality. Our experienced customer support teams are available to assist with site preparation, installation, and maintenance. It is our sincere hope that your experience with us has and will continue to surpass your expectations. Thank you for your business, Tom Touchett President Table of Contents Introduction Page 1-2 System Components Page 2-3 Host Controller Installation & Programming.... Pages 3-4 Loading Smart Devices into System Pages 4-5 T-568B Pin-Out Wiring Page 6 Programming Switch Functions Pages 7-9 Test & Turn-Up Page 9 System Messages Pages 9-10 System Descriptions Pages Introduction Rath s SmartCare Solution is an intuitive notification system that meets all requirements for UL 1069 and UL The SmartCare Solution uses proprietary SmartLoop TM Power Technology that simplifies system wiring and programming while delivering a robust feature set not found in any other system of its type. The system scalability makes it a fit for virtually any facility size. Page 1

3 Minimum System Requirements A minimum system will consist of a Nurse Console, a Smart Dome Light (with at least one switch connected), and a Host Controller (with Power Supply). Additional Considerations: When installed in a residence, one call station must be permanently installed in each resident s bathroom. At least one call notification station must be permanently mounted, attached, or tethered to a fixed location. The emergency call system must not share its communication network with any other network or system. All devices connected directly to the wiring of a hardwired system, and all transmitters using the same frequency or channel and that are within range of a receiver of a wireless system, must be compatible with the emergency call system and evaluated for the intended purpose. Supplementary devices not evaluated for the intended purpose are permitted only if their connection to the network utilizes a compatible device evaluated for the purpose. Features & Functionality The SmartCare Solution is a state-of-the-art tone and visual nurse call system. This system is expandable from 1 up to 300 Smart Devices on a system. Smart Devices include Nurse Consoles for nurses stations, Smart Domes for resident rooms, Duty Stations for break rooms, Zone Lights for hallway intersections, or Staff Stations for labs or exam rooms. Switch Stations can be plugged directly into any of the Smart Devices via an RJ45 connection. General System Maintenance All connected components should be tested for proper functionality a minimum of once per year (unless otherwise specified). System Components System Components- A system consists of a Host Controller, +24vdc Power Supply, up to 4 Expansion Boards (optional), Smart Devices, and Switch Stations all properly connected via SmartLoops TM. SmartLoop TM - A 24 gauge, 4 pair wire connection not to exceed 1,000 in total length. A SmartLoop TM originates from the Host Controller and is connected through multiple Smart Devices. For additional SmartLoops TM, a larger quantity of Smart Devices, or when a longer loop length is required, an Expansion Board can be connected to the SmartLoop TM connection on the Host Controller. The T-568B pin-out of the wiring allows the SmartLoop TM to provide all control signals and power to all Smart Devices. The end point of a SmartLoop TM is terminated with a termination plug consisting of a 120ohm resistor connected across pins 1 and 2 on an RJ45 connector. Smart Device- Any of the following items can have switches attached: Smart Dome Light Staff Station Smart Zone Light Nurse Console Duty Station Host Controller- Primary control unit for the SmartCare Solution. All programming is stored on this unit and it provides operating voltage and signaling to all connected Smart Devices. It has a defined port for connection to a sounder that is used for a catastrophic system failure alert and 3 flexible switch ports (two of which must be used for the Remote Sounder and System Power Monitor Board). All 4 SmartLoop TM connections are populated with termination connectors that are to be placed on the Comm Out port at the last device Expansion Board- Used for installations requiring SmartLoop TM lengths over 1,000 from Host Controller or more than 135 Smart Devices. Switch Stations- User stations that, when activated, provide a specifically programmed notification within the system. Wiring from Switch Stations uses the same cable and pin-out as a SmartLoop TM. Lengths from Switch Stations to associated Smart Devices cannot exceed 80. They are: Bedside Station (with call cord) Pull String Station Panic Station Code Blue Station Code Blue Station Check-In Station Remote Sounder Page 2

4 Connecting System Components Wiring is to be completed using 24 gauge, 4 pair, Cat 5 (or higher), solid conductor wire. T-568B wiring pin-out is required (see page 6). Determine the Number of Runs Required from the Host Controller to Smart Devices 1. SmartLoops TM begin at Host Controller and can be a total length of up to 1,000 feet. 2. A loop can contain up to 45 Smart Devices or 1 Nurse Console. 3. Total number of Smart Devices cannot exceed Up to 4 loops can be made directly to the Host Controller. 5. A loop connection to the Host Controller can be connected to an Expansion Board for greater distances and capacity. 6. An Expansion Board has 4 loop connections: One for feed in from Host Controller and three additional that support up to 45 Smart Devices each on loops up to 1,000 feet in length. 7. Smart Devices are connected to a port on the Host Controller, a port on the Expansion Board, or to each other. Note: The last device in a loop must have a termination connector inserted (RJ45 connector with a 120ohm resistor across pins 1 and 2). 8. Switches are connected to Smart Devices (up to 6 per) in switch connector locations using the same wiring parameters as Smart Device connections to system. The only exceptions are to the Smart Zone Light and Duty Station, which have Switch Port 6 reserved for a local sounder, and the Nurse Console which has Switch Port 1 dedicated for a local sounder, and Switch Port 6 dedicated for a primary power failure alarm. Host Controller Installation & Programming Powering Host Controller 1. Knock-out desired metal port on Power Supply case 2. Connect the Hot Wire of the 120vac to the L screw on the Power Supply 3. Connect the Neutral Wire of the 120vac to the N screw 4. Connect the Ground Wire of the 120vac to the Ground screw 5. Adjust voltage to +24vdc 6. Connect + and from Power Supply to appropriate terminals on Host Controller Note: It is recommended that the Power Supplies used with this system are connected to an Uninterruptible Power Source (UPS). Page 3

5 Recommended PC The computer used to access the Host Controller should meet the following requirements: Windows 7 operating system or later Mozilla Firefox version 27 or later, Google Chrome At least 2GB of RAM 10/100 Mbps Ethernet interface card Connecting Host Controller The Host Controller comes from the factory configured with a static IP address of To initially communicate with the Host Controller you will need to directly connect a personal computer or laptop. Configure Network Settings To connect to the Host Controller, you will first need to configure network settings on your laptop or personal computer. 1. From the Control Panel, click Network and Internet 2. Click Network and Sharing Center 3. Click Change Adapter Settings 4. Right click on the local area connection used to connect to the network and select Properties 5. Double click Internet Protocol Version 4 (TCP/IPv4) 6. Select the Use the Following IP Address radio button 7. Set the IP address to Set the subnet mask to Click OK Connect PC to Host Controller 1. Apply power to Host Controller 2. Connect Ethernet port of Host Controller to NIC of laptop 3. Open Command Prompt 4. Run successful Ping Proceed to Loading Smart Devices into System section Loading Smart Devices into System Copy Software to PC 1. Locate the included USB jump drive 2. Insert it into the PC s USB port 3. Copy the System Programming folder to the desktop Load Smart Device Information into Host Controller 1. From copied folder, open Pre-Configurator Executable Page 4

6 2. Scan the barcode labels from the included Control Log (placed on during equipment receipt) 3. Type description/location in field 4. Select board type from pull-down menu 5. Press Next Board button to load information (this must be done for all boards, including final input) 6. Repeat this procedure until all Smart Devices are added to system 7. When completed, click the Save button to write information to the system 8. Remove power from Host Controller. Do not re-apply power until ALL devices have been connected (see Connecting System Components section) and system is ready for turn-up. Page 5

7 T-568B Pin-Out Wiring Page 6

8 Programming Switch Functions Important: Before continuing, all Switch Station and Smart Device connections to system and power to the Host Controller and Expansion Boards (if used) need to be completed. Configurator Software 1. On USB jump drive locate the configurator.exe file 2. Copy file to laptop 3. Connect Ethernet port of Host Controller to NIC of laptop as described in Loading Smart Devices into System section 4. Launch configurator Set System Date & Time 1. Click on date and select date setting 2. Click on time box and input time in 24 hour format Set Check-In Time (If Applicable) 1. Click on Check-In start time box and input desired start time for this feature 2. Click on Check-In end time and input desired end time for this feature 3. Click on any of the Smart Devices listed on left panel under Control list to load changes to Host Controller Initial Screen (See Page 8) Display should have all Smart Devices loaded from pre-configurator listed in left Control column in the order they were entered into the system Date/time is in lower part of screen, but not displayed Check-in start and end times are below the date/time Switch Station Refers to up to 6 switches connected to selected Smart Devices. Connected ports will be colored GREEN. Available ports are RED. Switch Action Defined activity when a switch is activated/de-activated. Specific actions are defined on the right. Defined actions are colored GREEN. Undefined actions are RED. To automatically have actions that activate light/sound, have the inverse programmed to the next switch action. Once an action is fully defined, hit the Undo Action button. Example: Switch Action 1 for Switch Station 1 turns on LED 28 of the Nurse Console. The sequence to turn off the LED is automatically understood by the system. To clear previously programmed Switch Actions, press the Clear Action button To save programmed actions and write them to the Host Controller memory, click on a Smart Device (other than the one being programmed) or exit the Configurator and choose the Save and Exit option Programming Actions Select Smart Device from Control column Select Switch Station number (1-6) to be programmed Note: Station numbers of connected switches are GREEN and Switch Type is populated Set priority level if different from default (1 is highest priority) Page 7

9 State varies depending on Switch Type Check-In Station: Check-In, Cancel, No Show Code Blue, Panic, Pull String Station: Call or No Call Bedside Station: Call, No Call, Cancel, Unplugged Remote Sounder: No programmable actions by selection switch Control: Select the Smart Device (from pull-down menu) which has the connected switch or LED to activate/de-activate Type: swstation or LED (which item is to be affected) ID: If above was swstation, select port to which Switch Station is connected (1-6). If LED, select number of LED to be illuminated (1-3 for Smart Dome/Zone Light, for Nurse Console). LED: If type was swstation, this will be an option. Select to turn LED of local swstation on/off Sound: If type was swstation, this will be an option. Select to turn sounder of local swstation on/off and select sound rate (fast/slow/solid tone) Color: If type is set to LED select the desired color for the LED Blink: Select desired flash rate for LED (none, slow, medium, fast) Page 8

10 Default Switch Actions Switch Type Priority Local Switch LED Smart Device Action Call Cancel Action Bedside Station (Call Button Pressed) Bedside Station (Cord Unplugged) 5 On Steady Center LED On/White/Steady All Off 2 On Steady Center LED On/White/Medium Flash All Off Pull String Station 2 On Steady Center LED On/Red/Medium Flash All Off Panic Station 2 On Steady Center LED On/Red/Medium Flash All Off Code Blue Station 1 On Steady Center LED On/Blue/Fast Flash All Off Check-In (Pressed During Specified Time) Check-In (Not Pressed During Specified Time) 8 On Steady No Visible Action All Off 4 On Slow Flash Center LED On/Green/Slow Flash No Visible Action Staff Station 3 On Steady Top LED On/Amber/Medium Flash All Off Test & Turn-Up Once all devices have been properly connected to their respective wiring, power on the Host Controller and, if necessary, Expansion Boards. Proceed to each Switch Station and test to ensure proper actions are occurring with activation/de-activation of the stations. System Messages Messages Generated by the System An Informational Message is any event that should be indicated, but does not negatively affect system peripheral operations or basic Nurse Call operations (it may be indicating that an operation s functionality has been restored). New Switch Station inserted Switch Station occupied setting has changed (Check-In only) System Failure Switch Station OK System Alert Switch Station OK Communication Port power has been restored Network connection up Network connection down Clock has been set Clock has been auto-adjusted for DST Communication port communications have been restored SD card inserted Page 9

11 System Messages (Continued) Warnings Generated by the System A Warning is an event that prevents a system from functioning properly, but does not affect basic Nurse Call operations. Communication Port near power capacity System primary power loss RTC battery low SD card removed SD card write protected SD card near capacity Faults Detected by the System A Fault is an event that prevents the system from functioning as a Nurse Call device (it is configured by the user or defined by the default configuration). These actions cause the Remote Sounder connected to the Host Controller to activate. Switch Station removed Switch Station shorted Switch Station bad switch Switch Station bad ID System Failure Sounder absent System Alert Sounder absent Communication port over-current Communication lost Trademarks Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Mozilla and Firefox are registered trademarks of the Mozilla Foundation. Celeron, Core, Pentium, and Intel are trademarks of Intel Corporation in the U.S. and/or other countries. All brand other names and product names used in this manual are trademarks, registered trademarks, or trade names of their respective holders. Page 10

12 System Descriptions 2900-HC Host Controller Description The Host Controller is the brains and central hub of the Nurse Call Solution. Communication signaling, data, and power are distributed to every component of the system via SmartLoop TM Power Technology. It is recommended that this controller be powered by a UPS. Technical Specifications 24vdc Programmed using provided software via local Ethernet port Digital display with navigation buttons SD card for logging, storing, and reporting USB used for backup configuration save/load Switch port connection for Primary Power Monitor Board and up to (2) Remote Sounder connections System failure output System failure connector for catastrophic system failure notification via connected sounder (4) RJ45 SmartLoop TM connections for up to (45) Smart Dome Lights, (1) Nurse Console, or (1) Expansion Board connection Dimensions: 8.76 H x W x 2.81 D Weight: 4.15 lbs. (4) Head-End Serial Comm Ports (Locally Pre-Terminated). Connect up to (45) Smart Domes Lights, (1) Nurse Console, or (1) Expansion Board per Connector. System Normal 10:01:31 LCD for System Status Messages Incoming Power 24vdc + - Ethernet Connection for Configuring Serial Port for Connection to Paging System System Alarm Failure for Normal Installations: Connect to Buzzer Board and place on wall of cabinet or remotely where failure can be heard (3) Switch Inputs for Local Switch Panels (if desired) Page 11

13 Primary Power Detection Board (Mounted in Host Controller) Connection to Switch Ports 1-3 on Host Controller 12vdc Input 2900-EB Expansion Board Description The Expansion Board is used when a system is larger than the capability of the Host Controller alone or the distances exceed maximum reach (1000 ). The Expansion Board communicates data back to the Host Controller and distributes power via SmartLoop TM Technology. It is recommended that this controller be powered by a UPS. Technical Specifications 24vdc (3) RJ45 SmartLoop TM connections for up to (45) Smart Dome Lights and (1) Nurse Console (1) connection from Host Controller Dimensions: 8.76 H x W x 2.81 D Weight: 4.15 lbs. (4) Head-End Serial Comm Ports (Locally Pre-Terminated). Connect up to 25 downstream devices including Nurse Consoles and Dome Controllers. + Incoming Power 24vdc - System Alarm Failure for Normal Installations: Connect to Buzzer Board and place on wall of cabinet or remotely where failure can be heard (3) Switch Inputs for Local Switch Panels (if desired) Page 12

14 Nurse Console (28 Zone Pictured) Description The Nurse Console is a Smart Device that communicates back with the Host Controller and requires a direct connection to the Host Controller or an Expansion Board. The SmartCare Solution can have up to four consoles on a single system. Different colors, flash rates, and tones are programmed to identify what type of device has been activated and the labeled LED will indicate where it originated. There are four flash settings (steady, slow, medium, fast) and six colors to choose from. All RBG LEDs are programmed individually. The sounder type can also be customized. The green system status LED indicates that the Nurse Console is connected. The red primary power loss LED and sounder activate upon AC power loss. The sounders can be set to high volume, low volume, or can be muted momentarily with the toggle switch. Operation When a device is activated and registered to annunciate at the Nurse Console, that specific LED will illuminate. Once the call has been cancelled, the light and tone will shut off. During a call, the tone can be muted momentarily or until another station is activated using the left toggle switch. Technical Specifications RJ45 connector (1 IN and 1 OUT) 24 AWG, 8 conductor Material: Powder coated aluminum Dimensions: 7.68 H x W x 1.03 D Weight: 1.87 lbs. 28 Zone Nurse Console Front View o O g B b G br BR T-568B Pin-Out Switch Port 1 for Local Sounder Daisy-Chain Extension Ports: Loop Through Multiple Boards for Larger Systems (28 Zone Shown) (2) Serial Comm Link In/Out Connect to Up/Down Stream Boards OR Terminate Unused 120 Primary Power Fail Alarm Back View Page 13

15 LED Layout When programming Nurse Console LEDs, refer to the following: 28 Zone Programming LED Count LED 1 LED 8 LED 15 LED 22 LED 2 LED 9 LED 16 LED 23 LED 3 LED 10 LED 17 LED 24 LED 4 LED 11 LED 18 LED 25 LED 5 LED 12 LED 19 LED 26 LED 6 LED 13 LED 20 LED 27 LED 7 LED 14 LED 21 LED Zone Programming LED Count LED 1 LED 15 LED 29 LED 43 LED 2 LED 16 LED 30 LED 44 LED 3 LED 17 LED 31 LED 45 LED 4 LED 18 LED 32 LED 46 LED 5 LED 19 LED 33 LED 47 LED 6 LED 20 LED 34 LED 48 LED 7 LED 21 LED 35 LED 49 LED 8 LED 22 LED 36 LED 50 LED 9 LED 23 LED 37 LED 51 LED 10 LED 24 LED 38 LED 52 LED 11 LED 25 LED 39 LED 53 LED 12 LED 26 LED 40 LED 54 LED 13 LED 27 LED 41 LED 55 LED 14 LED 28 LED 42 LED Zone Programming LED Count LED 1 LED 15 LED 29 LED 43 LED 57 LED 71 LED 85 LED 99 LED 2 LED 16 LED 30 LED 44 LED 58 LED 72 LED 86 LED 100 LED 3 LED 17 LED 31 LED 45 LED 59 LED 73 LED 87 LED 101 LED 4 LED 18 LED 32 LED 46 LED 60 LED 74 LED 88 LED 102 LED 5 LED 19 LED 33 LED 47 LED 61 LED 75 LED 89 LED 103 LED 6 LED 20 LED 34 LED 48 LED 62 LED 76 LED 90 LED 104 LED 7 LED 21 LED 35 LED 49 LED 63 LED 77 LED 91 LED 105 LED 8 LED 22 LED 36 LED 50 LED 64 LED 78 LED 92 LED 106 LED 9 LED 23 LED 37 LED 51 LED 65 LED 79 LED 93 LED 107 LED 10 LED 24 LED 38 LED 52 LED 66 LED 80 LED 94 LED 108 LED 11 LED 25 LED 39 LED 53 LED 67 LED 81 LED 95 LED 109 LED 12 LED 26 LED 40 LED 54 LED 68 LED 82 LED 96 LED 110 LED 13 LED 27 LED 41 LED 55 LED 69 LED 83 LED 97 LED 111 LED 14 LED 28 LED 42 LED 56 LED 70 LED 84 LED 98 LED 112 Page 14

16 2900-3SZL Series Smart Zone Light Description The Smart Zone Light is used to locally annunciate calls from associated rooms and/or devices. It is a Smart Device that communicates back with the Host Controller and is daisy-chain wired on a single cable. The high efficiency LEDs give off a bright and clean light and are contained and divided by a white cover. The local sounder will annunciate when an associated device is activated. Operation When an associated Switch Station or zone is activated, the Smart Zone Light can be custom programmed to light up any of the three RBG or white LEDs. There are four flash settings (steady, slow, medium, fast) and six color options. The sounder will annunciate at the same rate as the flash of the light. Technical Specifications SmartLoop TM Power Technology RJ45 connectors: SmartLoop TM IN and OUT Switch Station ports 24 AWG, 8 conductor Dimensions: Face plate: 4-1/2 H x 6-3/8 W (three gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out Comm OUT to Next Smart Device OR Terminator Plug Comm IN from SmartLoop TM Switch Port 1 for Local Sounder Switch Ports 2-6 for Local Switch Connections Back View Page 15

17 2900-2SDL Series Smart Dome Light Description The Smart Dome Light is used to locally annunciate calls from associated rooms. It is a Smart Device that communicates back with the Host Controller and is daisy-chain wired on a single cable. The high efficiency LEDs give off a bright and clean light and are contained and divided by a white cover. Operation When an associated Switch Station is activated, the Smart Dome Light can be custom programmed to light up any of the three RBG or white LEDs. There are four flash settings (steady, slow, medium, fast) and six color options. Technical Specifications SmartLoop TM Power Technology RJ45 connectors: SmartLoop TM IN and OUT Switch Station ports 24 AWG, 8 conductor Dimensions: Face plate: 4-1/2 H x 4-1/2 W (two gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out Comm OUT to Next Smart Device OR Terminator Plug Back View (6) Switch Inputs (may vary by application) Page 16

18 2900-1CI Series Check-In Station Description The Check-In Station comes with a push button and a call placed LED. The station requires a single connection to the nearest Smart Device. Operation The Check-In Station uses proprietary Check-In Software that is loaded into every Host Controller. The device is activated by pressing the momentary push button causing the call placed LED to turn on steady. If the button is pressed within the programmed check-in time range, the device will automatically reset and no further action is required. If the button is not pressed, the software will let the staff know that the device has not checked in. The alert is cleared by pressing the check-in button. Mount As Shown Defaults If unit is not pressed during check-in time: Local switch LED slow flash, center LED on Smart Dome Light green/slow flash If unit checks-in: Local LED on/steady Technical Specifications SmartLoop TM Power Technology RJ45 connector/t-568b pin-out 24 AWG, 8 conductor (maximum 80 to Smart Device connector) Minimum voltage is 0.0vdc if the switch is absent (otherwise maximum is 0.125vdc) Maximum voltage is 1.0vdc if the switch is shorted (otherwise maximum is 0.875vdc) Dimensions: Face plate: 4-1/2 H x 2-3/4 W (single gang) Minimum back box depth: 2-1/8 o O g B b G br BR T-568B Pin-Out RJ45 Connector to Smart Device Back View Page 17

19 2900-1PS Series Pull String Station & PSW Series Water Resistant Pull String Station Description The Pull String Station comes with a 6 polyester cord, a heavy-duty slide switch, and a call placed LED. The station requires a single connection to the nearest Smart Device. Use PSW when mounting in a wet or damp environment. Operation When the heavy-duty slide switch goes from the UP/OFF position to the DOWN/ON position, the call has been placed. This can be done by pulling the 6 polyester cord or sliding the switch down. The call placed LED will turn on steady letting the calling party know that the call has been placed. To cancel the call, slide the switch up to the OFF position. Defaults Center LED of Smart Dome Light: Red color/medium flash Local Switch LED: On-steady, priority 2 Technical Specifications SmartLoop TM Power Technology RJ45 connector/t-568b pin-out 24 AWG, 8 conductor (maximum 80 to Smart Device connector) Minimum voltage is 0.0vdc if the switch is absent (otherwise maximum is 0.125vdc) Maximum voltage is 1.0vdc if the switch is shorted (otherwise maximum is 0.875vdc) Dimensions: Face plate: 4-1/2 H x 2-3/4 W (single gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out RJ45 Connector to Smart Device Back View Page 18

20 2900-1BS Series Bedside Station Description The Bedside Station comes with a cancel button, a call placed LED, and a 1/4 plug for a standard call cord. The station only requires a single connection to the nearest Smart Device. Operation When the button on the call cord is pressed, the call has been placed. The call placed LED will turn on steady letting the calling party know that the call has been placed. If the call cord is unplugged from the socket, it will activate the device as a priority call. To cancel the station, be sure the call cord is plugged in and press the cancel button. Defaults Button Pressed: Smart Dome Light center LED on/white/steady, priority 5 Cord Pulled Out: Smart Dome Light center LED on/white/medium flash, priority 2 Technical Specifications SmartLoop TM Power Technology RJ45 connector/t-568b pin-out 24 AWG, 8 conductor (maximum 80 to Smart Device connector) Minimum voltage is 0.0vdc if the switch is absent (otherwise maximum is 0.125vdc) Maximum voltage is 1.0vdc if the switch is shorted (otherwise maximum is 0.875vdc) 1/4 standard plug-in Dimensions: Face plate: 4-1/2 H x 2-3/4 W (single gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out RJ45 Connector to Smart Device Back View Page 19

21 2900-2DBS Series Dual Bedside Station Description The Dual Bedside Station comes with two cancel buttons, two call placed LEDs, and two 1/4 plugs for standard call cords. The station requires two independent connections to the nearest Smart Device. Operation When the button on either call cord is pressed, the call has been placed. The associated call placed LED will turn on steady letting the calling party know that the call has been placed. If a call cord is unplugged from the socket, it will activate the device as a priority call. To cancel the station, be sure the call cord is plugged in and press the cancel button. Defaults Button Pressed: Smart Dome Light center LED on/white/steady, priority 5 Cord Pulled Out: Smart Dome Light center LED on/white/medium flash, priority 2 Technical Specifications SmartLoop TM Power Technology (2) RJ45 connector/t-568b pin-out (2) 24 AWG, 8 conductor (maximum 80 to Smart Device connector) Minimum voltage is 0.0vdc if the switch is absent (otherwise maximum is 0.125vdc) Maximum voltage is 1.0vdc if the switch is shorted (otherwise maximum is 0.875vdc) (2) 1/4 standard plug-ins Dimensions: Face plate: 4-1/2 H x 4-1/2 W (two gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out RJ45 Connectors to Smart Device Back View Page 20

22 2900-1CB/2900-1PB Series Code Blue/Panic Stations Description The Code Blue and Panic Stations come with a push button and a call placed LED. The devices only require a connection to the nearest Smart Device. Mount As Shown Code Blue Station Operation When the blue button is pressed, the call has been placed. The call placed LED will turn on steady letting the calling party know that the device has been activated. After five seconds, the button can be pressed again to cancel the call. Panic Station Operation When the red button is pushed in, the call has been placed. The call placed LED will turn on steady letting the calling party know that the device has been activated. To cancel the call, twist the button in a clockwise direction. Code Blue Station Defaults Center LED of Smart Dome Light: Red/medium flash Local Switch LED: On steady, priority 2 Technical Specifications SmartLoop TM Power Technology RJ45 connector/t-568b pin-out 24 AWG, 8 conductor (maximum 80 to Smart Device connector) Minimum voltage is 0.0vdc if the switch is absent (otherwise maximum is 0.125vdc) Maximum voltage is 1.0vdc if the switch is shorted (otherwise maximum is 0.875vdc) Dimensions: Face plate: 4-1/2 H x 2-3/4 W (single gang) Minimum back box depth: 2-1/8 Panic Station RJ45 Connector to Smart Device o O g B b G br BR T-568B Pin-Out Back View Page 21

23 2900-3DS Series Duty Station Description The Duty Station is used to audibly and visually annunciate calls. It is a Smart Device that communicates back with the Host Controller and is daisy-chain wired on a single cable. The high efficiency LEDs give off a bright and clean light and are contained and divided by a white cover. Operation When an associated device or zone is activated, the Duty Station can be programmed to light up any of the three RBG or white LEDs. There are four flash settings (steady, slow, medium, fast) and six color options. The sounder will annunciate in high or low volume and can be momentarily muted with the toggle switch. Technical Specifications SmartLoop TM Power Technology RJ45 connectors: SmartLoop TM IN and OUT Switch Station ports 24 AWG, 8 conductor Dimensions: Face plate: 4-1/2 H x 6-3/8 W (three gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out Comm OUT to Next Smart Device OR Terminator Plug Comm IN from SmartLoop TM Switch 6 Used for Local Sounder Back View Switch Ports 1-5 for Local Switch Connections Page 22

24 2900-4SS Series Staff Station Description The Staff Station is used to audibly and visually annunciate calls. It is a Smart Device that communicates back with the Host Controller and is daisy-chain wired on a single cable. The red 1-1/2 push button is used for staff emergency calls and the call placed LED verifies that the call has been placed. The high efficiency LEDs give off a bright and clean light and are contained and divided by a white cover. Operation When an associated device or zone is activated, the Staff Station can be programmed to light up any of the three RBG or white LEDs. There are four flash settings (steady, slow, medium, fast) and six color options. The sounder will annunciate in high or low volume and can be momentarily muted with the toggle switch. The push button can be programmed to annunciate in any location and in any fashion when it is pressed. Technical Specifications SmartLoop TM Power Technology RJ45 connectors: SmartLoop TM IN and OUT Switch Station ports 24 AWG, 8 conductor Dimensions: Face plate: 4-1/2 H x 8-3/16 W (four gang) Minimum back box depth: 2-1/8 Mount As Shown o O g B b G br BR T-568B Pin-Out Comm OUT to Next Smart Device OR Terminator Plug Comm IN from SmartLoop TM Switch Port 1 for Local Push Button Connection Switch 6 Used for Local Sounder Switch Ports 1-5 for Local Switch Connections Back View Page 23

25 2900-1RS Series Remote Sounder Description/Operation The Remote Sounder is activated when a system fault is detected by the Host Controller. The sounder should be mounted in an area where the audible signal can be heard by appropriate personnel. The three position toggle switch can be used to modify the audio level (momentary mute, high, low). Only a single connection to the Host Controller is required. Technical Specifications SmartLoop TM Power Technology RJ45 connector 24 AWG, 8 conductor Dimensions: Face plate: 4-1/2 H x 2-3/4 W Minimum back box depth: 2-1/8 Mount As Shown Connect to any of Switch Ports 1-3 on Host Controller Back View Page 24

26 2900-PWRS2 Power Supply CAUTION: Do not touch exposed metal parts. Shut off branch circuit power before installing or servicing equipment. To reduce the risk of fire or electric shock, do not expose the unit to excessive moisture. This equipment is to be installed by qualified service personnel. Description Dimensions: 8.76 H x W x 2.81 D Weight: 5.2 lbs. 24vdc, 211W, 8.8 Amp, single output Switchable input voltage: 115vac or 230vac LED power indicator Recommended connection to UPS Maximum current draw on a fully populated system is 120vac) Connections Connect the hot wire of the 120vac to the L screw on the Power Supply Connect the neutral wire of the 120vac to the N screw on the Power Supply Connect the ground wire of the 120vac to the ground screw on the Power Supply Connect one lead of the DC power connection to the V screw and the other to the +V screw Maintenance Unit should be tested at least once a year for proper operation as follows: Output Voltage Test: Under normal load conditions the DC output voltage should be checked for proper voltage level ( vdc recommended range). Voltage Adjustment Potentiometer 24v to Host Controller 120vac Page 25

27 RP Uninterruptible Power Supply (UPS) Specifications Dimensions: 3.1 H x 10.6 W x 5.9 D Weight: 4.5 lbs. Output Power Capacity: 350VA / 255W 120vac Sealed, lead acid, maintenance free battery Underwriters Laboratory (UL) recognized RoHS compliant Audible alarm Battery backup and surge protected outlets keep the system running when the power goes out during an emergency Surge only outlet for connection to Power Monitor Board in Host Controller Expected run-time assuming 10% system activity on a fully populated system is 25 minutes Page 26

28 RP BR Uninterruptible Power Supply (UPS) Specifications Dimensions: 9.7 H x 3.9 W x 10.2 D Weight: 15 lbs. Output Power Capacity: 1000VA / 600W 120vac Sealed, lead acid, maintenance free battery Underwriters Laboratory (UL) recognized RoHS compliant Visual and audible alarms LCD screen gives utility and battery backup status Battery backup and surge protected outlets keep the system running when the power goes out during an emergency Surge only outlet for connection to Power Monitor Board in Host Controller Expected run-time assuming 10% system activity on a fully populated system is 78 minutes Page 27

29 RP PF Uninterruptible Power Supply (UPS) Specifications Dimensions: 10.4 H x 14.2 W x 3.9 D Weight: 24.7 lbs. Output Power Capacity: 1500VA / 900W 120vac Sealed, lead acid, maintenance free battery Underwriters Laboratory (UL) recognized RoHS compliant Visual and audible alarms LCD screen gives utility and battery backup status Battery backup and surge protected outlets keep the system running when the power goes out during an emergency Surge only outlet for connection to Power Monitor Board in Host Controller Expected run-time assuming 10% system activity on a fully populated system is 94 minutes Page 28