Packaging (5) Protection (3) Isolation Voltage (4)

Transcription

1 Features Regulated Converters Regulated output with internal linear regulator Isolated.5W power in SMD package Up to 2kVDC isolation Industry standard pinout -4 C to + C operating temperature IEC/EN/UL certified, CB report Description The is similar to the R1SX but with the addition of an internal linear regulator to give a precise, load-independent and low noise output. The output is also continuously short circuit protected. In the event of a continuous overload or over-temperature condition, the output will shut down thus protecting the converter from damage. The output will automatically restart once the fault condition has been lifted. Typical applications include isolated 5V supplies for sensor, bus-interface and test and measurement circuits..5 Watt SMD Single Output Selection Guide Part nom. Input Output Output Efficiency max. Capacitive Number Voltage Voltage Current typ. (1) Load (2) [VDC] [VDC] [ma] [%] [µf] -55/P (3) Note1: Efficiency is tested at nominal input and full load at +25 C ambient Note2: Max Cap Load is tested at nominal input and full resistive load Model Numbering Output Power nom. Input Voltage nom. Output Voltage - /_ P-R Packaging (5) Protection (3) Isolation Voltage (4) E UL certified CAN/CSA-C22.2 No certified UL695-1 certified CAN/CSA-C22.2 No certified IEC/EN certified IEC/EN695-1 certified CB report EN5532 compliant EN5524 compliant Note3: standard part is with continuous short circuit protection Note4: without suffix, standard isolation voltage (1kVDC/1 second) with suffix /H, high isolation voltage (2kVDC/1 second) Note5: with suffix -R, standard packaging tape and reel with suffix -Tray for optional tray packaging Ordering Examples: -55/P-R 5Vin 5Vout Single Output 1kVDC/ 1 minute isolation with SCP function tape and reel packaging -55/HP-R 5Vin 5Vout Single Output 2kVDC/1 minute isolation with SCP function tape and reel packaging -55/P-Tray 5Vin 5Vout Single Output 1kVDC/ 1 minute isolation with SCP function tray packaging -55/HP-Tray 5Vin 5Vout Single Output 2kVDC/1 minute isolation with SCP function tray packaging REV.: /219 ECO-1

2 BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter Input Voltage Range nom. Vin = 5VDC ±5.% Input Current Quiescent Current nom. Vin = 5VDC 2mA Minimum Load % Internal Operating Frequency Output Ripple and Noise (6) 2MHz BW 3mVp-p mvp-p 2kHz Note6: Measurements are made with a.1µf MLCC across output. (low ESR) 2mA capacitor Efficiency vs. Load 9 8 Efficiency [%] REGULATIONS Parameter Condition Value Output Accuracy -.5 typ. / ±2.% max. Line Regulation low line to high line, full load ±1.% max. Load Regulation % to % load.5 typ. / 1.% max. Deviation vs. Load Deviation [%] REV.: /219 ECO-2

3 PROTECTIONS Parameter Type Value Short Circuit Protection (SCP) below mw continuous, automatic recovery Isolation Voltage Isolation Resistance Isolation Capacitance Leakage Current Insulation Grade Note7: Note8: I/P to O/P standard with suffix /H standard with suffix /H tested for 1 second rated for 1 minute (7) tested for 1 second rated for 1 minute (7) For repeat Hi-Pot testing, reduce the time and/or the test voltage Refer to local safety regulations if input over-current protection is also required. Recommended fuse: slow blow type 1kVDC 5VAC 2kVDC 1kVAC GΩ min. pf max. 1µA max. 2µA max. functional ENVIRONMENTAL Parameter Condition Value Operating Temperature Range full natural convection.1m/s (see graph) -4 C to +85 C Operating Altitude Operating Humidity non-condensing 5% - 95% RH max. Pollution Degree Vibration MTBF according to MIL-HDBK-217F, G.B. +25 C +85 C 5m PD2 according to MIL-STD-22G 23 x ³ hours 2 x ³ hours Derating Graph (@ Chamber and natural convection.1m/s) Ambient Temperature [ C] REV.: /219 ECO-3

4 SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Standard requirements Information Technology Equipment, General Requirements for Safety requirements (CB Scheme) requirements E E UL , 2nd Edition, 214 CAN/CSA -C22.2 No , 2nd Edition UL695-1, 2nd Edition, 214 CAN/CSA C-22.2 No , 2nd Edition IEC :214, 2nd Edition EN :214 + A11:217 Information Technology Equipment, General Requirements for Safety (CB Scheme) IEC695-1:25, 2nd Edition + A2:213 E Information Technology Equipment, General Requirements for Safety EN695-1:26 + A2:213 RoHS2+ RoHS 211/65/EU + AM215/863 EMC Compliance Condition Standard / Criterion Electromagnetic Compatibility of Multimedia Equipment - Emission Requirements Information technology equipment - Immunity characteristics - Limits and methods of measurement with external filter (see filter suggestion) EN5532:215 + AC:216, Class B EN5524:2 + A1:215 ESD Electrostatic discharge immunity test Air: ±6kV ; Contact: ±4kV EN6-4-2:29, Criteria A Fast Transient and Burst Immunity ±.5kV EN6-4-4:212, Criteria A Surge Immunity ±1.kV EN6-4-5:217, Criteria A EMC Filtering Suggestions for EN5532 Class B L1 C2 +V in +V in +V out +V out C1 -V in -V in -V out -V out Component List C1 C2 L1 µf MLCC 47pF/3kVDC µh SMD Inductor DIMENSION and PHYSICAL CHARACTERISTICS Parameter Type Value Material Dimension (LxWxH) Weight base PCB black plastic (UL94V-) FR4 (UL94V-) x 11. x 8.5mm 1.6g typ. continued on next page REV.: /219 ECO-4

5 Dimension Drawing (mm) CG max. Pin Connection Pin # Single 1 -Vin 2 +Vin 4,5 -Vout 7 +Vout NC 2.5 4x2.54= Recommended Footprint Details 1.27 CG= center of gravity NC= no connection Tolerance: xx.x= ±.5mm xx.xx= ±.25mm Pin dimension: ±.1mm Bottom View.7 7 Top View PACKAGING INFORMATION Packaging Dimension (LxWxH) Packaging Quantity Tape Width Storage Temperature Range Storage Humidity tape and reel (carton) reel tray tape and reel tray 355. x 34. x 35.mm 33.2 x 33.2 x 3.mm 26. x 25. x 27.mm 25pcs 3pcs 24.mm -55 C to +125 C 5% - 95% RH max. The product information and specifications may be subject to changes even without prior written notice.the product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. REV.: /219 ECO-5