MDT Datasheets Contents. Page

Transcription

1 MDT Datasheets 2012 EW EW EW EW EW EW EW EW EW Contents Switch Actuators AKS/AKI Switch Actuators AKS, new series Switch Actuators with current measurement AMI/AMS Switch Actuators compact AKK Universal Actuators AKU Shutter Actuators JAL Heating Actuators AKH Dimming Actuator/Control device AKD DaliControl IP Gateway Binary Inputs BE, floating contacts, 230VAC, 12-24VDC Universal Interface USB Interface, IP Interfaces, Line Coupler Bus Power Supplies Temperature Controller/Sensor Room Temperature Controller 55mm/surface mounted Push Button 55mm/Push Button Plus 55mm with LED Glas Push Buttons/Glas Push Buttons with temperature sensor Presence Detectors ceiling mounted, new series Weather Station/Sun-/Rain Sensor VisuControl Touchpanel KX RF Line Coupler KX RF Glas Push Button with Actuator KX RF Push Button Plus 55mm with/without Actuator KX RF Switch Actuator KX RF Shutter Actuator Page Page 1 -- Zert.r

2 MDT Switch Actuator AKS/AKI MDT Switch Actuator 4/8/12-fold, MDRC Version AKS Switch Actuator 4-fold 4SU MDRC, 230VAC, 16A, C-Load 100uF AKS Switch Actuator 4-fold 4SU MDRC, 230VAC, 10A, C-Load 100uF AKI Switch Actuator 4-fold 4SU MDRC, 230VAC, 16A, C-Load 200uF AKS Switch Actuator 8-fold 8SU MDRC, 230VAC, 16A, C-Load 100uF AKS Switch Actuator 8-fold 8SU MDRC, 230VAC, 10A, C-Load 100uF AKI Switch Actuator 8-fold 8SU MDRC, 230VAC, 16A, C-Load 200uF AKS Switch Actuator 12-fold 12SU MDRC, 230VAC, 16A, C-Load 100uF AKS Switch Actuator 12-fold 12SU MDRC, 230VAC, 10A, C-Load 100uF AKI Switch Actuator 12-fold 12SU MDRC, 230VAC, 16A, C-Load 200uF The MDT Switch Actuator receives KX/EIB telegrams and switches up to 12 independent electrical loads. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator has separate power supply terminals for each channel (AKS 08/12 Two contacts/phase, from Q3 each contact own phase). The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKI/AKS-08xx.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Push Button and LED indicator for each channel O and C contact operation Time functions (swich-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data, 8 scenes per channel Central switching functions and block functions Programmable behavior in case of bus voltage failure or return AKI/AKS-12xx.01 AKI 04/08/12: Each contact has an own supply phase AKS 04: Each contact has an own supply phase AKS 08/12 Two contacts/phase, from Q3 each contact own phase AKI/AKS 04: Power supply via KX bus AKI/AKS 08/12: Power supply 230VAC, from Q3 via KX bus Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page 2 -- Zert.r

3 MDT Switch Actuator AKS/AKI Technical Data AKS AKS AKS AKS AKS AKS AKI AKI AKI umber of outputs Output switching ratings Ohmic load 16A 10A 16A/20A* Capacitive load max. 100uF at 16A max. 100uF at 10A max. 200uF at 16A Voltage 230VAC 230VAC 230VAC Maximum inrush current 400A/150μs 200A/600μs 400A/150μs 200A/600μs 600A/150μs 300A/600μs Maximum load Incandescent lamps 2700W 2000W 3680W Halogen lamps 230V 2500W 1500W 3680W Halogen lamps, electronic transformer** 1000W 700W 2000W Fluorescent lamps, not compensated 1800W 1600W 3680W Fluorescent lamps, parallel comp. 1000W 700W 2500W Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel 16A 10A 20A Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply*** 230VAC/50Hz 230VAC/50Hz 230VAC/50Hz Power consumption <0,3W <0,3W <0,4W <0,3W <0,3W <0,4W <0,3W <0,3W <0,4W Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 4/8/12SU 4/8/12SU 4/8/12SU * total current carrying capacity neighbouring outputs max. 32 A ** low voltage halogen lamps with electronic transformer *** AKI/AKS 08/12: Power supply 230VAC, from Q via KX Bus. AKS/AKI 04: Power supply via KX bus Examplary circuit diagram AKS Examplary circuit diagram AKI ote: AKI/AKS 08/12: Power supply 230VAC, from Q via KX Bus. -- Page 3 -- Zert.r

4 EW MDT Switch Actuator AKS MDT Switch Actuator 4/8/12/20-fold, MDRC Version AKS Switch Actuator 4-fold 4SU MDRC, 230VAC, 16A, C-Load 140uF AKS Switch Actuator 8-fold 6SU MDRC, 230VAC, 16A, C-Load 140uF AKS Switch Actuator 12-fold 8SU MDRC, 230VAC, 16A, C-Load 140uF AKS Switch Actuator 20-fold 12SU MDRC, 230VAC, 16A, C-Load 140uF The new AKS series offers more channels at less space. so lower costs per channel. The MDT Switch Actuator receives KX/EIB telegrams and switches up to 20 independent electrical loads. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator has separate power supply terminals for each channel and are very space saving by ideal form factor. The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKS Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Space saving by ideal form factor Push Button and LED indicator for each channel O and C contact operation Time functions (swich-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel AKS Central switching functions and block functions Programmable behavior in case of bus voltage failure or return Each contact has an own supply phase Power supply via KX bus Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page 4 -- Zert.r

5 EW MDT Switch Actuator AKS AKS AKS Technical Data AKS AKS umber of outputs Output switching ratings Ohmic load Capacitive load Voltage Maximum inrush current Maximum load Incandescent lamps Halogen lamps 230V Halogen lamps, electronic transformer* Fluorescent lamps, not compensated Fluorescent lamps, parallel comp. 16A max. 140uF at 16A 230VAC 600A/150μs 250A/600μs 3000W 3000W 1500W 2500W 1800W Max. number of electronic transformers 20 Output life expectancy (mechanical) Max. fuse per channel 16A Max. total current of the actuator 64A 96A 128A 192A Screw terminal KX busconnection terminal Power supply 0,8mm Ø, solid core via KX bus Power consumption <0,3W <0,3W <0,4W <0,5W Operation temperature range 0 to + 45 C Enclosure IP 20 Dimensions MDRC (Space Units) 4/6/8/12SU * low voltage halogen lamps with electronic transformer Examplary circuit diagram AKS Page 5 -- Zert.r

6 MDT Switch Actuator AMS/AMI MDT Switch Actuator 4/8/12-fold with current measurement, MDRC Version AMS Switch Actuator 4-fold 4SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement AMI Switch Actuator 4-fold 4SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement AMS Switch Actuator 8-fold 8SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement AMI Switch Actuator 8-fold 8SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement AMS Switch Actuator 12-fold 12SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement AMI Switch Actuator 12-fold 12SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement The MDT Switch Actuator receives KX/EIB telegrams and switches up to 12 independent electrical loads. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. The MDT Switch Actuator offers current measurement for each channel and measurement of the total current. In dependence on the parameterization the measured data can be transmit in different data formats (ma/a/kw) onto the KX bus. Additionally the device provides an hour/service interval meter. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. The MDT Switch Actuator has a separate power supply terminals for each channel. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AMS/AMI-04xx.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Push Button and LED indicator for each channel O and C contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Hour meter AMS/AMI-08xx.01 Central switching functions and block functions Programmable behaviour in case of bus voltage failure or return Each contact has an own supply phase Integrated current measurement (current, kwh, limit value) Power supply via KX bus Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page 6 -- Zert.r

7 MDT Switch Actuator AMS/AMI Technical Data AMS AMS AMS AMI AMI AMI umber of outputs Current measurement range 20mA - 16A 20mA - 16A Output switching ratings Ohmic load 16A 16A Capacitive load max. 100uF at 16A max. 200uF at 16A Voltage 230VAC 230VAC Maximum inrush current Maximum load 400A/150μs 200A/600μs 600A/150μs 300A/600μs Incandescent lamps 2700W 3680W Halogen lamps 230V 2500W 3680W Halogen lamps, electronic transformer* 1000W 2000W Fluorescent lamps, not compensated 1800W 3680W Fluorescent lamps, parallel comp. 1000W 2500W Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel 16A 16A Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX bus via KX bus Power consumption <0,3W <0,4W <0,4W <0,3W <0,4W <0,4W Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions MDRC (Space Units) 4/8/12SU 4/8/12SU * low voltage halogen lamps with electronic transformer Examplary circuit diagram AMS/AMI Page 7 -- Zert.r

8 MDT Switch Actuator AKK MDT Switch Actuator compact 2/4/8/16-fold, MDRC MDT Switch Actuator 1/2-fold, flush mounted MDT Switch Actuator 8-fold, surface mounted Version AKK Switch Actuator 2-fold 2SU MDRC, 230VAC, 16A AKK Switch Actuator 4-fold 2SU MDRC, 230VAC, 6A AKK Switch Actuator 8-fold 4SU MDRC, 230VAC, 16A AKK Switch Actuator 8-fold 4SU MDRC, 230VAC, 10A AKK Switch Actuator 16-fold 8SU MDRC, 230VAC, 16A AKK Switch Actuator 16-fold 8SU MDRC, 230VAC, 10A AKK-01UP.01 Switch Actuator 1-fold Flush mounted, 230VAC, 16A AKK-02UP.01 Switch Actuator 2-fold Flush mounted, 230VAC, 6A AKK-0810A.01 Switch Actuator 8-fold Surface mounted, 230VAC, 10A The MDT Switch Actuator AKK receives KX/EIB telegrams and switches up to 16 independent electrical loads. Each output uses a monostable relay. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs were switched off. After mains voltage recovery the relay position will be restored. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MRDC Switch Actuators use a common power supply terminal for four channels. The surface mounted and flush mounted Switch Actuators have a common power supply terminal. This feature simplifies the wiring and increases clarity of the circuit. The MDT Switch Actuator AKK is available as modular installation device, surface mounted device and flush mounted device for fixed installation in dry rooms. For project design and commissioning of the MDT Switch Actuator AKK it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKK AKK-0810A.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices O and C contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Central switching functions and block functions AKK-01UP.01 AKK-02UP.01 Programmable behavior in case of bus voltage failure or return Four contacts share one supply phase (MDRC device) Common supply phase (UP and AP device) Power supply 230VAC Integrated bus coupling unit -- Page 8 -- Zert.r

9 MDT Switch Actuator AKK Technical Data AKK-01UP.01 AKK-02/08/ AKK-08/ AKK-0810A.01 AKK-02UP.01 AKK umber of outputs Output switching ratings Ohmic load 16A 10A** 6A** Capacitive load 21uF at 10A 21uF 7uF at 3A Voltage 230VAC 230VAC 230VAC Maximum inrush current 80A/150μs 40A/600μs 80A/150μs 40A/600μs 30A/150μs 15A/600μs Maximum load* Incandescent lamps 2300W 1900W 1000W Halogen lamps 230V 2000W 1400W 800W Halogen lamps, electronic transformer 800W 500W 300W Fluorescent lamps, not compensated 800W 500W 300W Fluorescent lamps, parallel comp. 180W 120W 60W Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel 16A 10A 6A Screw terminal*** KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core AKK 01/02: via KX bus Power supply 230VAC/50Hz via KX bus AKK 08/16: 230VAC/50Hz Power consumption <0,5W <0,5W 0,5-2W 0,5-4W 0,5-2W 0,5-4W <0,5W <0,5W Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 2/4/8SU 4/8SU 4SU Dimensions UP/AP (W x H x D) 41mm x 41mm x 24mm 100mm x 40mm x 88mm 41mm x 41mm x 24mm * the total current of each supply terminal should not exceed maximum output switching current. ** not suitable to switch AC outlets *** UP device with cable connections **** depends on the switching position of the output relays Examplary circuit diagram AKK Examplary circuit diagram AKK-0810A Page 9 -- Zert.r

10 EW MDT Universal Actuator MDT Universal Actuator 8/16-fold, MDRC Version AKU Universalaktor 8-fold 4SU MDRC, 230VAC, 16A AKU Universalaktor 16-fold 4SU MDRC, 230VAC, 16A The MDT Universal Actuator receives KX/EIB telegrams and can be used as Switch Actuator or Shutter Actuator. Mixed applications from Switch- and Shutter Actuator are possible. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. Functions as Switch Actuator: The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. Functions as Shutter Actuator: The outputs are parameterized individually via ETS3/4. The device provides extensive functions like status response, block functions, central function and positioning shutters, blinds and other hangings. Additionally the device provides up to 8 scenes per channel. If the mains voltage fails, all outputs are switched off. After bus voltage failure or recovery the position of the shutter is selected in dependence on the parameterization. The MDT Universal Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Universal Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKU Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Can be used as Switch Actuator or Shutter Actuator Mixed applications from Switch- and Shutter Actuator possible Push Button and LED indicator for each channel O and C contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data, 8 scenes per channel AKU Central switching functions and block functions Operation mode blind/shutter programmable Travel-, pause-at-change-of-direction- and step time adjustable 1-bit automatic function and sun protection 8-bit positioning for shutter and blinds Programmable behaviour in case of bus voltage failure or return Four contacts share one supply phase Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

11 EW MDT Universal Actuator Technical Data AKU AKU umber of Switching outputs 8 16 umber of Shutter outputs 4 8 Output switching ratings Ohmic load 16A 16A Capacitive load max. 21uF at 16A max. 21uF at 16A Voltage 230VAC 230VAC Maximum inrush current Maximum load 80A/150μs 40A/600μs 80A/150μs 40A/600μs Shutter motor* 600W 600W Incandescent lamps 2300W 2300W Halogen lamps 230V 2000W 2000W Halogen lamps, electronic transformer** 800W 800W Fluorescent lamps, not compensated 800W 800W Fluorescent lamps, parallel comp. 180W 180W Max. number of electronic transformers 3 3 Output life expectancy (mechanical) Max. fuse per channel 16A 16A Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply 230VAC/50Hz 230VAC/50Hz Power consumption** <0,5-2W <0,5-4W Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions MDRC (Space Units) 4SU 8SU * no three-phase asynchronous ** Power consumption when operate as Shutter Actuator 0,5W. Power consumption when operate as Switch Actuator depends on relays position. Examplary circuit diagram AKU Page Zert.r

12 MDT Shutter Actuator MDT Shutter Actuator 2/4/8-fold, MDRC MDT Shutter Actuator 1-fold, flush mounted MDT Shutter Actuator 4-fold, surface mounted Version JAL Shutter Actuator 2-fold 2SU MDRC, 6A, shutter motors 230VAC up to 300W JAL Shutter Actuator 4-fold 4SU MDRC, 10A, shutter motors 230VAC up to 600W JAL Shutter Actuator 8-fold 8SU MDRC, 10A, shutter motors 230VAC up to 600W JAL-0410D.01 Shutter Actuator 4-fold 4SU MDRC, 8A, shutter motors 24VDC up to 180W JAL-0810D.01 Shutter Actuator 8-fold 8SU MDRC, 8A, shutter motors 24VDC up to 180W JAL-01UP.01 Shutter Actuator 1-fold Flush mounted, 6A, shutter motors 230VAC up to 300W JAL-0410A.01 Shutter Actuator 4-fold Surface mounted, 10A, shutter motors 230VAC up to 600W The MDT Shutter Actuator receives KX/EIB telegrams and controls up to 8 independent shutter or sunblind drives. Each output uses two monostable relays. The MDRC shutter Actuators can be operated manually via a push button. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like status response, block functions, central function and positioning shutters, blinds and other hangings. Additionally the device provides up to 8 scenes per channel. If the mains voltage fails, all outputs are switched off. After bus voltage failure or recovery the position of the shutter is selected in dependence on the parameterization. The MRDC Shutter Actuators use a common power supply terminal for two channels. The surface mounted and flush mounted MDT Shutter Actuators have a common power supply terminal. This feature simplifies the wiring and increases clarity of the circuit. The MDT Shutter Actuator is available as modular installation device, surface mounted device and flush mounted device for fixed installation in dry rooms. For project design and commissioning of the MDT Shutter Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at JAL JAL JAL-0410A.01 JAL-01UP.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Push Button and LED indicator for each channel ( Only MDRC device) Operation mode blind/shutter programmable Travel-, pause-at-change-of-direction and step time adjustable 1-bit automatic function and sun protection 8-bit positioning for shutter and blinds 8 scenes per channel, alarm, central- and block functions Programmable behavior in case of bus voltage failure or return Two contacts share one supply phase (MDRC device) Common supply phase (UP and AP device) Integrated bus coupling unit -- Page Zert.r

13 MDT Shutter Actuator Technical Data JAL JAL JAL-0410A.01 JAL-0410D.01 JAL-0810D.01 JAL JAL-01UP.01 umber of channels 4/8 4/8 1/2 Output switching ratings Ohmic load 10A 8A 6A Voltage 230VAC 24VDC 230VAC Maximum load Shutter motor* 600W 180W 300W Output life expectancy (mechanical) Max. fuse per channel 16A 10A 10A Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power Supply 230VAC/50Hz 230VAC/50Hz via KX Bus Power consumption < 0,5W <0,5W < 0,3W Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 4/8SU 4/8SU 2SU Dimensions UP/AP (W x H x D) 100mm x 40mm x 88mm -- 41mm x 41mm x 24mm * no three-phase asynchronous motor Examplary circuit diagram JAL Examplary circuit diagram JAL-0410D Page Zert.r

14 MDT Heating Actuator MDT Heating Actuator 4/8-fold, MDRC Version AKH Heating Actuator 4-fold 2SU MDRC, to control electrothermic valve drives VAC AKH Heating Actuator 8-fold 4SU MDRC, to control electrothermic valve drives VAC The MDT Heating Actuator receives KX/EIB telegrams and controls up to independent electrical outputs. Each channel has its own LED indicator. Each channel supplies up to 5 electrothermic valve drives and can be parameterized individually via ETS3/4. The channels are controllable with PWM (1-bit) or 1-byte telegrams. The integrated temperature controller manages the actuating value given by external KX temperature sensors. The temperature controller offers comfort-, night-, frost protection- and summer- /winter- operation. The MDT Heating Actuator detects mains voltage failure and has emergency operation if the cyclic telegram is missing. Additionally they provide objects for heating request and cyclic movement of the valves. The MDT Heating Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Heating Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKH AKH Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Each channel controls up to 5 electrothermic valve drives Controllable with 1-bit or 1-byte telegram Direct controllable by KX temperature sensors Integrated temperature controller (PI, Two-position, PWM) Comfort-, night- and frost protection. Summer-/winter operation Emergency operation if cyclic telegram is missing Short-circuit detection of connected load Detection of 230VAC mains voltage failure Objects for heating request and cyclic movement of the valves Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

15 MDT Heating Actuator Technical Data AKH AKH umber of outputs 4/8 Output switching current 24VAC and ohmic load 230VAC and ohmic load External switching voltage Maximum load umber of electrotermic valves* Output life expectancy Screw terminal KX busconnection terminal Power supply 500mA 500mA VAC 230VAC: 5 each channel 24VDC: 3 each channel Triac output, wearless 0,8mm Ø, solid core via KX bus Power consumption KX Bus < 0,3W Operation temperature range 0 to + 45 C Enclosure IP 20 Dimensions MDRC (Space Units) 2/4SU * depends on manufacturer. Inrush current for 5 electrothermic valves has to be < 1A each electrothermic valve Examplary circuit diagram AKH Page Zert.r

16 MDT Dimming Actuator MDT Dimming Actuator 1/2/4-fold, MDRC Version AKD Dimming Actuator 2-fold 4SU MDRC, 230VAC, 250W AKD Dimming Actuator 4-fold 8SU MDRC, 230VAC, 250W AKD Dimming Actuator 1-fold 4SU MDRC, 230VAC, 600W AKD Dimming Actuator 2-fold 8SU MDRC, 230VAC, 600W AKD-0410V.01 Control Device 4-fold 4TE MDRC, 1-10V The MDT Dimming Actuator receives KX/EIB telegrams and dimms/switches up to 4 independent electrical loads. Each output can be operated manually via a push button. The outputs are for switching and dimming incandescent lamps, HV halogen lamps, LV halogen lamps (with conventionel or suitable electronic transformers), dimmable energy saving lamps and LED lightning. Leading or trailing edge principle can be chosen. The device has an integrated shortcircuit and excess temperature protection plus softstart function to increase lamp life time. Programmable performance after mains voltage failure, bus voltage failure or return. The 1-10V MDT Control Device has embedded switching relays for 30 ECG/30W, 20 ECG/58W, 15 ECG/2x36W or 10ECG/2x58W. Each channel offers control voltage up to 30 electronic transformers (ECG). The MDT Dimming Actuator is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Dimming Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at AKD AKD AKD-0410V.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices 4W minimum load for LED lightning possible Push Button and LED indicator for each channel For dimming and switching incandescent lamps, HV halogen lamps, LV halogen lamps ( with conventional or suitable electronic transformers), dimmable energy saving lamps and LED lightning Dimming operation in leading or trailing edge Short circuit and temperature protection with alarm, softstart Time functions (swich-on/switch-off delay, staircase light function) Each contact has an own supply phase Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

17 MDT Dimming Actuator Technical Data AKD AKD AKD AKD Technical Data AKD-0410V.01 umber of outputs 2/4 1/2 umber of outputs 4 Switching voltage outputs 230VAC 230VAC Switching voltage outputs 230VAC Switching voltage control outputs 1-10V Maximum lamp load* 250W 600W Maximum number of ECG 30 Minimum lamp load** 12W 20W Maximum current switching relais 16A Maximum fuse per channel 10A 10A Maximum capacitive load 100uF Screw terminal Screw terminal KX busconnection terminal 0,8mm Ø, solid core KX busconnection terminal 0,8mm Ø, solid core Power supply via KX bus via KX bus Power supply via KX bus Power consumption*** < 0,3W < 0,3W Power consumption*** < 0,3W Power dissipation no load**** <0,5W <0,5W Power dissipation nominal load**** <4W <8W Operation temperature range 0 to + 45 C 0 to + 45 C Operation temperature range 0 to + 45 C Enclosure IP 20 IP 20 Enclosure IP 20 Dimensions MDRC (Space Units) 4/8SU 4/8SU Dimensions MDRC (Space Units) 4SU * Maximum load for dimmable energy saving lamps is 80W (AKD-xx01.01) or 200W (AKD-xx03.01) Maximum load for dimmable LED lamps is, depending on the LED lamp manufacturer, 25-80W (AKD-xx01.01) or W (AKD-xx03.01) ** Minimum load for dimmable LED lamps are 4-12W, depending on the LED lamp manufacturer *** Power consumption from KX Bus **** Maximum power dissipation for each channel ote: Dimming Actuators AKD have separate Power supply terminals for each channel. The channel outputs can not be bridged. Important assembly note: Conventionel transformers must be fused on primary side with adequate fuse according to the size of the transformator. Examplary circuit diagram AKD Examplary circuit diagram AKD Page Zert.r

18 MDT Dali Gateway MDT DaliControl IP Gateway with webinterface, MDRC Version SC-DALI64.01 DaliControl IP gateway 6SU MDRC, up to 64 ECG The MDT DaliControl IP Gateway receives KX/EIB telegrams and enables the classic control of 16 DALI groups plus individual control of the ECG. An example is switching or dimming of 2x16 light in groups (advantage of synchronous switching inside the group) plus 32 individual lights. The MDT DaliControl IP Gateway detects light and ECG errors and releases telegrams in dependence of its parameterisation. The commisioning after installation and group attribution of the MDT DaliControl IP Gateway is done with the buttons on the device or with the integrated webinterface. Quick identification and group attribution of the connected DALI segments can be done without connection to the KX bus. The network connection is realized with an RJ45 interface. Additionally the MDT DaliControl IP Gateway offers two binary inputs to connect push buttons or presence detectors. The MDT DaliControl IP Gateway is a modular installation device for fixed installation in dry rooms. It fits on 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT DaliControl IP Gateway it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-DALI64.01 Production in Germany certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Supports diifferent light types Dimming curve matches the human perception Simultanous dimming Tracking of operating hours and switch cycles Display and reporting of light and ECG errors Simple change of the configuration without using ETS Setting of light scenes without any knx modules Simple group attribution directly on the device Dali Commissioning via Webbrowser or directly on the device display Dali Commissioning via softwaretool Individual control up to 64 EVG Operation via integrated binary inputs without knx Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

19 MDT Dali Gateway Electrical Data SC-DALI64.01 Outputs umber of groups 16 umber of ECG 64 Maximum Dali voltage Maximum Dali current 18-21VDC 150mA Inputs umber of inputs 2 Maximum cable lenght Maximum signal voltage Screw terminal KX busconnection terminal Power Supply Power consumption 15m 9-36VDC 9-24VAC 0,8mm Ø, solid core 230VAC < 3W Operation temperature range 0 bis + 45 C Enclosure IP 20 Dimensions MDRC (Space Units) 6SU Examplary circuit diagram SC-DALI Page Zert.r

20 MDT Binary Input MDT Binary Inputs 4/8/16-fold, MDRC Version BE Binary Input 4-fold 2SU MDRC, Inputs for floating contacts BE Binary Input 4-fold 2SU MDRC, Inputs 24VAC/DC BE Binary Input 4-fold 2SU MDRC, Inputs 230VAC BE Binary Input 8-fold 4SU MDRC, Inputs for floating contac BE Binary Input 8-fold 4SU MDRC, Inputs 24VAC/DC BE Binary Input 8-fold 4SU MDRC, Inputs 230VAC BE Binary Input 16-fold 8SU MDRC, Inputs for floating contacts BE Binary Input 16-fold 8SU MDRC, Inputs 24VAC/DC BE Binary Input 16-fold 8SU MDRC, Inputs 230VAC The MDT Binary Input is available in 3 versions, input detection of 24VAC/DC signals, input detection of 230VAC signals and reading out of floating contacts. The Binary Input reacts depending on its programmed parameters and sends a telegram on the KX bus. You can connect conventional push-buttons or auxiliary contacts (e.g. door and window contacts) to the device. The MDT Binary Inputs include four integrated logical modules to implement logical operations and logical control. These logical modules interpret all the inputs plus two external objects. So you can easily create KX/EIB telegrams which are required in daily practice (e.g. fault telegrams or all windows closed ). Each Input is parameterized individually via ETS3f/4. The device provides extensive functions like switching of lighting, operation of blinds and shutters, counting of pulses, debounce time, contact type and telegram rate limitation. The command for rising and falling edge can be defined independently and with the block communication object each channel can be blocked or released. The logic module can release two telegrams after receiving a trigger signal from the inputs. The MDT Binary Input is a modular installation device for fixed installations in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Binary Input it is recommended to use the ETS3f/ETS4 or later. Please download the application software at BE BE BE Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices To connect conventional push buttons or window/auxiliary contacts 4 integrated logical modules Telegram rate limitation O or C contact operation, programmable length of button push Operation of blinds and shutters, 1 and 2 button operation Forced setting function for each output Operation with short/long button push and 2 objects Counting of pulses, suitable for 30ms S0 pulses Cyclical sending of contact state programmable Internal contact voltage 12V Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

21 MDT Binary Input Electrical Data BE BE BE BE BE BE BE BE BE umber of inputs 4/8/16 4/8/16 4/8/16 Signal voltage For floating contacts 230VAC 12-24VDC / 24VAC Internal contact voltage 12V Permitted input cable length 100m Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power Supply via KX bus via KX bus via KX bus Power consumption <0,3W <0,3W <0,3W Operation temperature range 0 bis + 45 C 0 bis + 45 C 0 bis + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 2/4/8SU 2/4/8SU 2/4/8SU Examplary circuit diagram BE Examplary circuit diagram BE Examplary circuit diagram BE Page Zert.r

22 MDT Universal Interface MDT Universal Interface 2/4-fold, flush mounted Version BE Universal Interface 2-fold Flush mounted, for floating contacts, with LED output BE Universal Interface 4-fold Flush mounted, for floating contacts, with LED output The MDT Universal Interface is to be inserted in a wiring box or behind a push button or switch. The inputs react depending on their programmed parameters and and send a telegram on the bus. You can connect conventional push-buttons or auxiliary contacts (e.g. door and window contacts) to the device. The length of connection cables is 22cm. Each input can be set as a LED output and drive a low current LED. The MDT Universal Interface includes four integrated logical modules to implement logical operations and logical control. These logical modules interpret all the inputs plus two external objects. So you can easily create KX/EIB telegrams which are required in daily practice (e.g. fault telegrams or all windows closed ). Each input is parameterized individually via ETS3/4. The device provides extensive functions like switching of lighting, operation of blinds and shutters, counting of pulses, debounce time, contact typ and telegram rate limitation. The command for rising and falling edge can be defined independently and with the block communication object each channel can be blocked or released. The logic module can release two telegrams after receiving a trigger signal from the inputs. The MDT Universal Interface is a flush mounted device to be inserted in a wiring box or behind a push button or switch. It has to be installed in dry rooms. For project design and commissioning of the MDT Universal Interface it is recommended to use the ETS3f/ETS4 or later. Please download the application software at BE BE Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices To connect conventional push-buttons or window/auxiliary contacts 4 integrated logical modules Telegram rate limitation O or C contact operation, programmable length of button push Operation of blinds and shutters, 1 and 2 button operation Forced setting function for each output Operation with short/long button push and 2 objects Counting of pulses Cyclical sending of contact state programmable Each output can be set as 1,5mA output for low current LED Flush mounted (length of connection cables: 22cm) Dimensions (W x H x D): 41mm x 41mm x 12mm Integrated bus coupling unit -- Page Zert.r

23 MDT Universal Interface Electrical Data BE BE umber of Inputs 4 2 KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core Power Supply via KX bus via KX bus Power consumption <0,3W <0,3W Permitted input cable length 5m 5m Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions UP (W x H x D) 41mm x 41mm x 12mm 41mm x 41mm x 12mm Examplary circuit diagram BE Examplary circuit diagram BE Page Zert.r

24 MDT USB/IP Interface MDT Interface, MDRC Version SC-USBR.01 USB Interface 2SU MDRC SC-IP IP Interface 2SU MDRC SC-IP IP Interface with Routing 2SU MDRC SC-LK Line Coupler 2SU MDRC MDT technologies offers four KX Interfaces to enable communication between PC and the KX/EIB system. KX USB Interface: The USB Interface enables the communication between the PC and the KX/EIB system. The USB interface is galvanically isolated from the KX/EIB bus. KX IP Interface: The IP Interface enables the communication between the PC and the KX/EIB system via LA. 5 simultaneous connections possible. An external power supply (12 to 24VAC/DC) or power over ethernet is required. KX IP Interface with routing: This interface offers the same functions as the IP Interface, but the device routes telegrams as a line coupler using the the LA. KX IP Line Coupler: The Line Coupler connects two KX lines to each other. Electrical isolation between the lines and reduction of the busload by using the filter function. The MDT KX Interfaces are modular installation devices for fixed installation in dry rooms. They fit on DI 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT KX Interfaces it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-USBR.01 SC-LK Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices USB Interface: To enable bidirectional communication between PC and the KX bus via USB Fully compatible to ETS3f/4 IP Interface: To enable bidirectional communication between PC and the KX bus TCP/IP 5 simultaneous connections possible (SC-IP only) Programming the KX bus via TCP/IP External power supply or PoE required Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

25 MDT USB/IP Interface Electrical Data SC-USBR.01 SC-IP SC-IP SC-LK Interface USB Ethernet Ethernet KX Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power Supply via KX bus 12 to 24VAC/DC 12 to 24VAC/DC via KX bus Power consumption < 0,3W < 0,8W < 0,8W <0,3W each line Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C 0 to +45 C Enclosure IP 20 IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 2SU 2SU 2SU 2SU -- Page Zert.r

26 MDT Power Supply MDT Power Supply, MDRC Version STV Power Supply 4SU MDRC, 160mA STV Power Supply 4SU MDRC, 320mA STV Power Supply 6SU MDRC, 640mA The MDT KX Power Supply with integrated choke produces the stabilized KX system voltage (30VDC) to supply the connected KX/EIB components. The operating status is indicated via 3 LED: Red LED: Reset of the KX/EIB bus Green LED: ormal operation, no faults Yellow LED: KX/EIB bus overload Once the fault has been rectified, the Power Supply restarts itself. Additionally the Power Supply STV offers a choke free output that can be used for a special battery module All devices able to supply 100% overload. The MDT KX Power Supply is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. STV STV STV Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices KX power supply with integrated choke Mains voltage 230VAC Short-circuit-proof 100% overload LED indicator for bus reset, normal operation and bus overload Button for bus reset on top Choke free output (STV only) Modular installation device for DI 35mm rails Integrated bus coupling unit -- Page Zert.r

27 MDT Power Supply Technical Data MDT STV MDT STV MDT STV Power Supply Supply voltage 230VAC/50Hz 230VAC/50Hz 230VAC/50Hz KX output voltage 30VDC 30VDC 30VDC Choke free output voltage VDC Output current ominal 160mA 320mA 640mA Maximal 350mA 700mA 1200mA Max. total current of both outputs mA Mains fuse 16A 16A 16A Screw terminal KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions MDRC (Space Units) 4SU 4SU 6SU Examplary circuit diagram STV Page Zert.r

28 MDT Temperature Controller MDT Temperature Controller 6-fold, MDRC MDT Temperature Controller/Sensor 6-fold, surface mounted Version SC-RT6REG.01 Temperature Controller 6-fold 2SU MDRC SC-RT6AP.01 Controller/Sensor 6-fold Surface mounted, for PT1000 sensors up to 12m cable length Accessories SC-RT6AP.001 SC-PTST3.01 Sensor Standard PT1000 sleeve probe with 3 m cable SC-PTA3.01 Sensor strap on installation PT1000 sleeve probe with 3 m cable SC-PTDE0.01 Sensor ceiling installation PT1000 probe for ceiling installation The MDT Temperature Controller is used for all purpose temperature control applications. The temperature is received as an KX object, additionally the SC-RT6AP.01 can manage up to 6 PT1000 temperature sensors. Depending on the adjusted parameters of the Temperature controller the actuating value is sent as 1-bit or 1-byte variable to the bus. The characteristic of the MDT Temperature Controller (Two-position, PI and PWM control) can be set in the ETS3/4. The thermostat stores the minimum and maximum temperature and releases an alarm telegram if the temperature differs from the programmed limit values. The temperature of the frost protection is parameterizable. The desired value can be given by MDT VisuControl touchpanel or the MDT pushbuttons. The MDT Temperature Controller Actuator REG is a modular installation device for fixed installation in dry rooms. It fits on DI 35mm rails in power distribution boards or closed compact boxes. The Temperature Controller Actuator AP is a surface mounted device, the maximum length of the PT1000 temperature sensors should not exceed 12m. Both MDT Temperature Controllers are for fixed installations in dry rooms. For project design and commissioning of the MDT Temperature Controllers it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-RT6REG.01 SC-PTST3.01 SC-RT6AP.01 SC-PTDE0.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Selectable temperature controller (PI,Two-position, PWM) Limit values min/max, Frost protection alarm, Memory for min/max Cyclical sending of contact state programmable Day-/night-/frost protection operation HVAC object and 1bit object to choose operation mode RHCC status and bit/byte objects to declare status Desired value can be given by visualisation, e.g. MDT VisuControl Integrated bus coupling unit -- Page Zert.r

29 MDT Temperature Controller Electrical Data SC-RT6REG.01 SC-RT6AP.01 umber of channels 6 6 Temperature sensors -- connection for PT1000 KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX bus via KX bus Power consumption <0,3W <0,3W Operation temperature range Encosure IP 20 IP 20 Dimensions (Space Units) 2SU -- Dimensions (W x H x D) mm x 64mm x 40mm Examplary circuit diagramm SC-RT6REG Page Zert.r

30 MDT RTC MDT Room Temperature Controller 1-fold, flush mounted MDT Room Temperature Controller 1-fold, surface mounted Version SC-RT1UP.01 Room Temperature Controller 1-fold Flush mounted, white, 55mm SC-TS1UP.01 Room Temperature Sensor 1-fold Flush mounted, white, 55mm SC-RT1UPE.01 Room Temperature Controller 1-fach with adjustment knob Flush mounted, white, 55mm SC-RT1APE.01 Room Temperature Controller 1-fach with adjustment knob Surface mounted, white The MDT Room Temperature Controller is used to control the indoor temperature, it has a working range from -10 to +50 C. The MDT Room Temperature Controller detects the temperature and releases telegrams in dependence on its parameterisation. The characteristic of the MDT Temperature Controller (Two-position, PI and PWM control) can be set in the ETS3/4. The MDT Room Temperature Controller stores the minimum and maximum temperature and releases an alarm telegram if the temperature differs from the programmed limit values. The temperature of the frost protection is parameterizable. Fits all switches with 55mm rocker: BERKER S1, B1, B3, B7 glass GIRA Standard 55, E2, Event, Esprit JUG A500, Aplus MERTE M-Smart, M-Arc, M-Plan The MDT Room Temperature Controller is a flush mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT Room Temperature Controller it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-RT1UP.01 SC-RT1UPE.01 SC-TS1UP.01 SC-RT1APE.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Fits all switches with 55mm rocker: - BERKER S1, B1, B3, B7 - GIRA Standard 55, E2, Event, Esprit - JUG A500, Aplus - MERTE M-Smart, M-Arc, M-Plan Selectable temperature controller (PI,Two-position, PWM) For indoor temperature controlling, range -10 to +50 C Limit values min/max, Frost protection alarm, Memory for min/max Desired value can be given by visualisation, e.g. MDT VisuControl Day-, night- and frost protection operation HVAC object and 1bit object to choose operation mode RHCC status and bit/byte objects to declare status Installation with support ring (Included in delivery) Integrated bus coupling unit -- Page Zert.r

31 MDT RTC Electrical Data SC-RT1UP.01 SC-RT1UPE.01 SC-TS1UP.01 SC-RT1APE.01 Configuration RTC RTC Temperature sensor RTC umber of Channels KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power Supply via KX bus via KX bus via KX bus via KX bus Power consumption <0,3W <0,3W <0,3W <0,3W Operating temperature range -10 to +50 C -10 to +50 C -10 to +50 C -10 to +50 C Enclosure IP 20 IP 20 IP 20 IP 20 Dimensions UP/AP (W x H x D) 55mm x 55mm x 13mm 55mm x 55mm x 13mm 91mm x 85mm x 26mm 91mm x 85mm x 26mm Examplary circuit diagram SC-xTxxxx Page Zert.r

32 MDT Push Button MDT Push Button 2/4/6/8-fold, flush mounted Version BE-TA Push Button 2-fold Flush mounted, white matt finish BE-TA Push Button 4-fold Flush mounted, white matt finish BE-TA Push Button 6-fold Flush mounted, white matt finish BE-TA Push Button 8-fold Flush mounted, white matt finish BE-TA55P2.01 Push Button 2-fold Plus Flush mounted, white matt finish, status and orientation LED BE-TA55P4.01 Push Button 4-fold Plus Flush mounted, white matt finish, status and orientation LED BE-TA55P6.01 Push Button 6-fold Plus Flush mounted, white matt finish, status and orientation LED BE-TA55P8.01 Push Button 8-fold Plus Flush mounted, white matt finish, status and orientation LED The MDT KX Push Button releases KX telegrams after pushing the buttons on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The centered title block allows individually marking of the MDT KX Push Button. You can use transparent or the lightgray film if no is marking is required. You find the marking draft in our download area. The MDT KX Push Button from the Plus series has an additional orientation LED and a bicolored (red/green) LED for each rocker. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 absent, LED green present, LED red window open. The logic module can release a second telegrams after receiving a trigger signal from the inputs. Fits all 55mm frames: BERKER S1, B1, B3, B7 glass GIRA Standard 55, E2, Event, Esprit JUG A500, Aplus MERTE M-Smart, M-Arc, M-Plan The MDT KX Push Button is a flush-mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the KX Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at BE-TA BE-TA55P2.01 BE-TA BE-TA55P8.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Fits all switches with 55mm rocker: - BERKER S1, B1, B3, B7 - GIRA Standard 55, E2, Event, Esprit - JUG A500, Aplus - MERTE M-Smart, M-Arc, M-Plan Push Buttons can be parameterized for 1 or 2 button operation O or C contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation Centered title block with cover film for individual marking Installation with support ring (included in delivery) Integrated bus coupling unit -- Page Zert.r

33 MDT Push Button Electrical Data BE-TA BE-TA55P2.01 BE-TA BE-TA55P4.01 BE-TA BE-TA55P6.01 BE-TA BE-TA55P8.01 umber of rockers umber of bicolored LED (TA-55xxP) Orientation LED (TA-55xxP) KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX Bus via KX Bus via KX Bus via KX Bus Power consumption <0,3W <0,3W <0,3W <0,3W Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 IP 20 Dimensions (W x H x D) 55mm x 55mm x 13mm 55mm x 55mm x 13mm 55mm x 55mm x 13mm 55mm x 55mm x 13mm Examplary circuit diagram BE-TAxx.01 Compatible to 55mm programs Manufacturer Series Berker Berker Berker Berker Berker Berker Gira Gira Gira Gira Gira Gira Merten Merten Merten Merten Merten Merten Jung Jung Jung Jung Jung B.7 Glas polarweiss B.3 Alu polarweiss S.1 polarweiss B.1 polarweiss matt B.7 Glas Alu S.1 polarweiss matt Standard 55 reinweiss seidenmatt E2 reinweiss seidenmatt Esprit Glas mint Esprit Glas weiss Event Alu Event reinweiss matt M-Smart polarweiss brillant M-Plan polarweiss edelmatt M-Arc polarweiss edelmatt Atelier-M polarweiss M-Plan Echtglas brillantweiss M-Smart polarweiss AS500 alpinweiss A500 alpinweiss A500 alpinweiss Aplus Alu A500 Alu -- Page Zert.r

34 EW MDT Glas Push Button MDT Push Button 2/4/6/8-fold Plus, flush mounted Version BE-GT04W.01 Glas Push Button 4-fold Plus Flush mounted, White, Surrounding orientation light BE-GT04S.01 Glas Push Button 4-fold Plus Flush mounted, Black, Surrounding orientation light BE-GT08W.01 Glas Push Button 8-fold Plus Flush mounted, White, Surrounding orientation light BE-GT08S.01 Glas Push Button 8-fold Plus Flush mounted, Black, Surrounding orientation light The MDT Glas Push Button releases KX telegrams after touching the sensor areas on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. For individually marking of the MDT Glas Push Button you can insert a labeling film behind the glas front. You find the marking draft in our download area. The MDT Glas Push Buttons has a surrounding orientation light LED and a bicolored (White/Red) LED for sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 absent, LED white present, LED red window open. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT Glas Push Button is a flush mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KX Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at BE-GT04W.01 BE-GT08W.01 BE-GT04S.01 BE-GT08S.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Sensor areas can be parameterized for 1 or 2 button operation O or C contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects White/Red LED for each sensor area Surrounding orientation light Brightness of LED adjustable via object Operation of blinds and shutters, 1 and 2 button operation Title block to insert behind glas front, labeling film included Installation with support ring (included in delivery) Integrated bus coupling unit -- Page Zert.r

35 EW MDT Glas Push Button Electrical Data BE-GT04W.01 BE-GT04S.01 BE-GT08W.01 BE-GT08S.01 umber of sensor areas 4 8 umber of bicolored LED 4 8 Orientation LED Surrounding Surrounding KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX bus via KX bus Power consumption <0,4W <0,4W Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions (W x H) 92mm x 92mm 92mm x 163mm Examplary circuit diagram BE-TAxx Page Zert.r

36 EW MDT Presence Detector MDT Presence Detector, flush mounted Version SC-P360D4.01 Presence Detector, 4 pyro detectors Light sensor (Presence 16/8m) SC-P360K4.01 Presence Detector, 4 pyro detectors Light sensor, constant level light intensity (Presence 16/8m) SC-P360D3.01 Presence Detector, 3 pyro detectors Light sensor (Presence 11/5m) SC-P360K3.01 Presence Detector, 3 pyro detectors Light sensor, constant level light intensity (Presence 11/5m) SC-P360D1.01 Presence Detector, 1 pyro detectors Light sensor (Presence 4m) The MDT Presence Detector is available in 2 versions, Presence Detector with light sensor and Presence Detector with light sensor plus constant level light intensity. Both Presence Detectors capturing the smallest movements with their built in pyro detectors and high resolution lens. The illuminance value is measured by a sensor and can be read out directly in lux. After presence detection a 1-bit or dimming value ( %) is send to the bus, the sensitivity is adjustable in 10 steps. The light sensor releases a telegram if the brighness value differs from the progammed value. Additionally the MDT Presence Detector has block objects for light and HVC channel and offers a module for scene control. The MDT Presence Detector with constant level light intesity can control up to 3 light rows (SC-P360K3.01: 1 light row). The MDT Presence Detector is a installation device for fixed installation in dry rooms, the preferred installation height is 2 up to 4 meters. 4 pyro detectors: The covered area for movement is 16m (Diameter), the covered area for presence is 8m (Diameter). 3 pyro detectors: The covered area for movement is 11m (Diameter), the covered area for presence is 5m (Diameter). 1 pyro detector: The covered area for presence is 6m (Diameter). For project design and commissioning of the MDT Presence Detector it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-PM360D4.01 SC-PM360D1.01 SC-PM360D3.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Presence detector with light sensor 4 pyro detectors plus high resolution lens Programmable sensibility (ot SC-P360D1.01) Switching function depending on brightness and movement Brighness value can be read out Master/slave function programmable Scene functions Day/ight function, monitoring with messages 2 zone operation (SC-P360x4.0 only) Integrated bus coupling unit -- Page Zert.r

37 EW MDT Presence Detector Electrical data SC-P360D4.01 SC-P360K4.01 SC-P360D3.01 SC-P360K3.01 SC-P360D1.01 Covered area (Diameter) Movement 16m 11m -- Presence 8m 5m 6m Sensitivity adjustable in 10 Steps adjustable in 10 Steps fixed, not adjustable Angular coverage Range of light sensor Lux Lux Lux KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX bus via KX bus via KX bus Power consumption <0,3W <0,3W <0,3W Operation temperature range 0 to + 40 C 0 to + 40 C 0 to + 40 C Enclosure IP 20 IP 20 IP 20 Dimensions (W x H xd) 85mm x 85mm x 38mm 75mm x 75mm x 35mm 43mm x 43mm x 30mm Covered area SC-P360x4.01 Covered area SC-P360x3.01 Examplary circuit diagram SC-P360xx.01 Covered area SC-P360x Page Zert.r

38 MDT Brightness/Weather MDT Brightness-/Weather devices Version SC-WS3HW.01 Weather Station Home Outdoor installation on wall or pole, flush mounted control unit SC-SS1H.01 Sun Sensor Indoor installation with vacuum cup, flush mounted control unit SC-RS Rain Sensor Outdoor installation, Surface mounted MDT technologies offers three Brightness / Weather devices: Wetter Station Home: 3 channels for sun protection to control blind/shutter Sun protection up to 3 facades Offers wide functions to control facades (2 switching treshold, teach in function) Brightness value for east, south, west, twilight Wind speed value, alarm if wind speed exceeds limit, temperature value Suited to control facades at home Installation on wall or pole, 5m connection cable o additional power supply required Integrated bus coupling unit Sun Sensor: Rain Sensor: Brightness sensor for indoor installation Integrated, automatically heating Input to connect push burron for blind control Heating operation by choke free output STV 640 Hysteresis and time delay programmable or external 24VDC power supply Installation with vacuum cup Current consumption of heating is 100mA 2m cable to connect controlling unit 5 m bus connection cable Flush mounted control unit Stainless fastening angle included in delivery Operation mode 1: Installation on window without blinds Dimensions (W x H x D): 67mm x 67mm x 29mm Operation mode 2: Installation on window with blinds Integrated bus coupling unit o additional power supply required Integrated bus coupling unit in control unit For project design and commissioning of the Brightness/Weather devices it is recommended to use the ETS3f/ETS4 or later. Please download the application software at SC-SS1H.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Integrated bus coupling unit SC-WS3HW.01 SC-RS Page Zert.r

39 MDT Brightness/Weather Technical Data SC-SS1H.01 SC-WS3HW.01 SC-RS Measured data Brightness Brightness, Wind, Twilight, Temperature KX busconnection 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply via KX Bus via KX Bus via KX Bus Power consumption < 0,3W < 0,3W < 0,3W* Operation temperature range 0 to + 45 C 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 IP 20 Dimensions control unit (W x H x D) 41mm x 41mm x 12mm -- 67mm x 67mm x 29mm * Without heating. Heating operation by choke free output STV 640 or external 24VDC power supply. Current consumption of heating is <100mA Rain Examplary circuit diagram SC-xSxxx Page Zert.r

40 MDT VisuControl MDT VisuControl Touchpanel Version VC /17,7 cm TFT Display Flush mounted VC ,4 /26cm TFT Display Flush mounted VC ,3 /33cm TFT Display Flush mounted VC ,3 /10,9cm TFT Display Webserver, MDRC The MDT VisuControl Touch Panel is used for the visualisation of the current building status and to control building functions. The display has a resolution of 1280 x 800 pixels (VisuControl 13,3 ), 800 x 600 pixels (VisuControl 10,4 ) or 800 x 480 pixels (VisuControl 7 ). The operation is interactively by touching the TFT display. The webserver is available as MDRC device with an resolution of 430 x 272 pixels (VisuControl 4,3 ). The VisuControl Touch Panel is individually programmable with VisuControl software. It offers standard functions like switching, dimming, shutter/blind control and extensive functions for scene control and visualizing trends (temperature, wind velocity, brightness etc.). To design your own customized screen, you can easiliy include images or user defined symbols. The VisuControl Lite software is included in delivery and contains several application examples. The internal clock in the touch panel allows to create presence simulations and timer functions. Additionally the display can log measured values. Either you can visualize them or export them to a spreadsheet. The included logical functions allow to implement logical operations and logical control. The logical functions interpret the existing telegrams. So you an easiliy create KX/EIB telegrams which are required in daily practice (e.g. fault telegrams or all windows closed ). The integrated LA connection is used for programming and allows to send s, web browsing and display RSS newsfeeds. With the VisuControl View software you can easiliy establish a remote connection and control your Touch Panel from anywhere. The KX/EIB bus connection is provided via the bus connection terminal. The VisuControl Lite software is included in delivery, without cover frame. VC VC VC VC Production certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Individually programmable Switching and dimming, shutter/blind control Remote Access via PC, ipad, iphone Alarm indication Logical linking of binary data Displaying trends Forwarding of informations via VisuControl lite software and demo projects included Integrated bus coupling unit -- Page Zert.r

41 MDT VisuControl Technical Data VC VC VC VC Screen size 4,3 7 10,4 13,3 Resolution 480 x 272 Pixel 800 x 600 Pixel 800 x 480 Pixel 1200 x 800 Pixel Screw terminal 2,5mm² 2,5mm² 2,5mm² 2,5mm² KX busconnection terminal 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core 0,8mm Ø, solid core Power supply 24VDC 24VDC 24VDC 24VDC Power consumption* < 9W < 10W < 11W < 12W Dimensions** Depth 149mm 45mm 59mm 59mm Breadth 109mm 188mm 277mm 360mm Height 49mm 148mm 224mm 254mm Weight 0,9kg 0,95kg 1,97kg 2,5kg Enclosure IP 20 IP 20 IP 20 IP 20 * backlight off ** with cover frame Examplary circuit diagram VC-xx Page Zert.r

42 EW MDT KX RF Line Coupler MDT KX RF Line Coupler, Flush mounted Version RF-LK KX RF Line Coupler Flush mounted The MDT KX RF Line Coupler connects MDT KX RF devices to the KX bus. The Line Coupler offers extensive filter functions to reduce the KX RF bus load. The Line Coupler allows bidirectional KX RF communication in system mode to the following devices: - KX RF Glas Push Button Plus with Actuator 4/8-fold - KX RF Push Button Plus 2/4/6/8-fold - KX RF Push Button Plus with Actuator 2/4/6/8-fold - KX RF Switching Actuator 1/2-fold - KX RF Shutter Actuator 1-fold The MDT KX RF Line Coupler is available as flush mounted installation device for fixed installation in dry rooms. For project design and commissioning of the MDT KX RF Line Coupler it is recommended to use the ETS3f/ETS4 or later. Please download the application software at RF-LK Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices KX RF line coupler to connect MDT KX RF devices like MDT Push Button RF or MDT Glas Push Button RF Protocol KX RF (multifrequency prepared) Flush mounted in socket Dimensions (W x H x D): 41mm x 41mm x 22mm Integrated bus coupling unit -- Page Zert.r

43 EW MDT KX RF Line Coupler Technical Data RF-LK Transmitter frequency* Range Output level Sensitivity 868,3MHz 150m 10dBm <105dBm KX busconnection terminal Power supply Power consumption 0,8mm Ø, solid core via KX bus <0,4W Operation temperature range 0 to + 45 C Enclosure IP 20 Dimensions (W x H x D) 41mm x 41mm x 24mm * Multifrequency prepared Examplary circuit diagram RF-LK Page Zert.r

44 EW KX RF Glas Push Button MDT KX RF Glas Push Button 2/4/6/8-fold Plus with Actuator, flush mounted Version RF-GTA4W.01 KX RF Glas Push Button 4-fold Plus Flush mounted with Actuator, White, Surrounding orientation light RF-GTA4S.01 KX RF Glas Push Button 4-fold Plus Flush mounted with Actuator, Black, Surrounding orientation light RF-GTA8W.01 KX RF Glas Push Button 8-fold Plus Flush mounted with Actuator, White, Surrounding orientation light RF-GTA8S.01 KX RF Glas Push Button 8-fold Plus Flush mounted with Actuator, Black, Surrounding orientation light The MDT KX RF Glas Push Buttons release KX telegrams after touching the sensor areas top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The MDT KX RF Glas Push Button is operating in bidirectional KX RF system mode and is perfectly suited to replace conventionel push buttons in existing installations without placing KX bus cables. The connections to the KX bus is realized via the MDT KX RF Line Coupler. The integrated actuator can be set as 2-fold switching actuator or 1-fold shutter actuator. For individually marking of the MDT KX RF Glas Push Button you can insert a labeling film behind the glas front. You find the marking draft in our download area. The MDT KX RF Glas Push Buttons have a surrounding orientation light LED and a bicolored (White/Red) LED for sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 absent, LED white present, LED red window open. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT KX RF Glas Push Button is a flushmounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KX RF Glas Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at RF-GTA4W.01 RF-GTA8W.01 RF-GTA4S.01 RF-GTA8S.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Commisioning with ETS3/4 Bidirektional KX RF communication in system mode Sensor areas can be parameterized for 1 or 2 button operation O or C contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation Can be set as 2-fold switching actuator or 1-fold shutter actuator Connection via MDT KX RF line coupler Title block to insert behind glas front, labeling film included To replace conventionel push buttons To upgrade your installation without placing KX bus cables Power supply 230VAC Surrounding orientation light Multifrequency in preperation Installation with support ring (included in delivery) -- Page Zert.r

45 EW KX RF Glas Push Button Electrical Data RF-GTA4W.01 RF-GTA4S.01 RF-GTA8W.01 RF-GTA8S.01 umber of sensor areas 4 8 umber of bicolored LED 4 8 Orientation LED 1 1 Transmitter frequency* 868,3MHz 868,3MHz Range 150m 150m Output level 10dBm 10dBm Sensitivity <105dBm <105dBm umber of outputs 2 4 Output switching ratings Ohmic load 10A 10A7 Capacitive load 21uF 21uF Voltage 230VAC 230VAC Screw terminal Power supply 230VAC 230VAC Power consumption <0,4W <0,4W Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions (W x H) 92mm x 92mm 92mm x 163mm * Multifrequency prepared Examplary circuit diagram RF-GTA4x Page Zert.r

46 EW MDT KX RF Push Button MDT KX RF Push Button 2/4/6/8-fach Plus, flush mounted Ausführungen RF-TA55P2.01 KX RF Push Button 2-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P4.01 KX RF Push Button 4-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P6.01 KX RF Push Button 6-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P8.01 KX RF Push Button 8-fold Flush mounted, white matt finish, status and orientation LED RF-TA55A2.01 KX RF Push Button 2-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A4.01 KX RF Push Button 4-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A6.01 KX RF Push Button 6-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A8.01 KX RF Push Button 8-fold Flush mounted with Actuator, white matt finish, status and orientation LED The MDT KX RF Push Button releases KX telegrams after pushing the buttons on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The MDT KX RF Push Button is operating in bidirectional KX RF system mode and is perfectly suited to replace conventionel push buttons in existing installations without placing KX bus cables. The connections to the KX bus is realized via the MDT KX RF Line Coupler. The integrated actuator can be set as 2-fold switching actuator or 1-fold shutter actuator (RF-TA55Ax.01 only). The centered title block allows individually marking of the MDT KX RF Push Button. You can use transparent or the lightgray film if no is marking is required. You find the marking draft in our download area. The MDT KX RF Push Button has an orientation light LED and a bicolored (Red/Green) LED for the sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 absent, LED green present, LED red window open. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT KX RF Push Button is a flush-mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KX RF Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at RF-TA55P2.01 RF-TA55P6.01 RF-TA55P4.01 RF-TA55P8.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Commissioning with ETS3/4 Bidirektional KX RF communication in system mode Fits all switches with 55mm rocker Push Buttons can be parameterized for 1 or 2 button operation O or C contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation 2-fold switching actuator or 1-fold shutter actuator (RF-TA55xA.01) Connection via MDT KX RF line coupler Centered title block with cover film for individual marking To replace conventionel push buttons To upgrade your installation without placing KX bus cables Power supply 230VAC Multifrequency in preperation Installation with support ring (included in delivery) -- Page Zert.r

47 EW MDT KX RF Push Button Electrical Data RF-TA55P2.01 RF-TA55P4.01 RF-TA55P6.01 RF-TA55P8.01 RF-TA55A2.01 RF-TA55A4.01 RF-TA55A6.01 RF-TA55A8.01 umber of sensor areas 2/4/6/8 2/4/6/8 umber of bicolored LED 2/4/6/8 2/4/6/8 Orientation LED 1 1 Transmitter frequency* 868,3MHz 868,3MHz Range 150m 150m Output level 10dBm 10dBm Sensitivity <105dBm <105dBm umber of outputs -- 2 Output switching ratings Ohmic load -- 10A Capacitive load -- 21uF Voltage VAC Screw terminal Power supply 230VAC 230VAC Power consumption <0,3W <0,3W Operation temperature range 0 to + 45 C 0 to + 45 C Enclosure IP 20 IP 20 Dimensions (W x H) 92mm x 92mm 92mm x 163mm * Multifrequency prepared Compatible to 55mm programs Manufacturer Series Examplary circuit diagram RF-TA55Ax.01 Berker Berker Berker Berker Berker Berker Gira Gira Gira Gira Gira Gira Merten Merten Merten Merten Merten Merten Jung Jung Jung Jung Jung B.7 Glas polarweiss B.3 Alu polarweiss S.1 polarweiss B.1 polarweiss matt B.7 Glas Alu S.1 polarweiss matt Standard 55 reinweiss seidenmatt E2 reinweiss seidenmatt Esprit Glas mint Esprit Glas weiss Event Alu Event reinweiss matt M-Smart polarweiss brillant M-Plan polarweiss edelmatt M-Arc polarweiss edelmatt Atelier-M polarweiss M-Plan Echtglas brillantweiss M-Smart polarweiss AS500 alpinweiss A500 alpinweiss A500 alpinweiss Aplus Alu A500 Alu -- Page Zert.r

48 EW KX RF Switch Actuator MDT KX RF Switch Actuator 1/2-fold, Flush mounted Version RF-AKK1UP.01 KX RF Switch Actuator 1-fold Flush mounted, 230VAC, 16A RF-AKK2UP.01 KX RF Switch Actuator 2-fach Flush mounted, 230VAC, 6A The MDT KX RF Switch Actuator receives KX/EIB telegrams and switchs up to 2 independent electrical loads. Each output uses a monostable relay. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. The MDT KX RF Switch Actuator is operating in bidirectional KX RF system mode and is perfectly suited for using in conventionel installations without placing KX bus cables. The connections to the KX bus is realized via the MDT KX RF Line Coupler. If the mains voltage fails, all outputs were switched off. After mains voltage recovery the relay position will be restored. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT KX RF Switch Actuator is available as flush mounted installation device for fixed installation in dry rooms. For project design and commissioning of the MDT KX RF Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at RF-AKK1UP.01 RF-AKK2UP.01 Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KX/EIB devices Commissioning with ETS3/ETS4 Bidirectional KX RF communication in system mode O and C contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Central switching functions and block functions Programmable behavior in case of bus voltage failure or return Flush mounted in socket Connection via MDT KX RF Line Coupler To upgrade your installation without placing KX bus cables Power supply 230VAC Dimensions (W x H x D): 41mm x 41mm x 22mm) -- Page Zert.r