CompactPCI Serial CVX-DVI

Transcription

1 Product Information CompactPCI Serial CVX- Dual DisplayPort to / Adapter Document No March 07

2 General The CVX- is a peripheral slot card for CompactPCI Classic systems. The board receives one or two DisplayPort compliant video signals via front panel mdp (Mini DisplayPort) input receptacles, and converts these data to classic output connectors, for legacy applications. The connectors are individually configurable as -D (digital video output), or -A (aka analog graphics over ). As an option, the connectors (both or one) can be replaced by classic style 5-pin D-Sub connectors. The video input signal of each mdp connector is routed to a high speed analog switch, as selectable data source for either a DP to converter (DP++ to TMDS, 4 lanes up to 6Gbps), or DP to adapter (DP++ to WUXGA, lanes up to.7gbps). Both type of video outputs are wired to -I front panel connectors. For usage on a -A output a suitable -A to adapter cable would be required. The CVX- converter can be powered via its backplane connectors, or operated stand-alone. CVX- Shown w. mdp Cable Connectors EKF -- ekf.com

3 Feature Summary General < PICMG CompactPCI Classic (CPCI.0) standard < Single size Eurocard 3U 4HP 00x60mm < Suitable for CompactPCI peripheral slot < CompactPCI backplane connector J for +5V supply & IC SMBus control < CompactPCI backplane connector J for rear I/O (option only) < Stand-alone operation available as an option (on-board power connector) Front Panel Connectors < x Mini DisplayPort receptacles (option x) - video input signals DP++ compliant < Option screw lock for mdp connectors < x -I connectors (option x) - selectable video output signals -D or -A () < Option connectors 5-pos. fem. HD-Sub (when populated will replace ) DisplayPort Multiplexer < HD3SS5 6 Gbps DisplayPort : Differential Switch < Input from mdp receptacle < Output path selectable either to TMDS (-D) converter or to adapter DisplayPort to TMDS < SN65DP59 6 Gbps DP++ Retimer < Digital Video Interface ().0 compliant output signals < Data rates up to UHD EKF -3- ekf.com

4 Converter < PTN3355 DisplayPort to adapter < -lane and -lane input modes supported < High bit rate (HBR.7Gbps) and reduced bit rate (RBR.6Gbps) supported < Triple 8-bit DAC, up to 40MHz < Wide set of display resolutions, up to 90x440, 60 Hz, 8 bpp, 34 MHz pixel clock < VESA standards to WUXGA supported < Output path individually selectable to either front panel connector or backplane connector J (option only) Applications < For recent CPU cards which are provided with DP or mdp graphics connectors < and monitor support for legacy applications < Railway, transportation, automation Environment & Regulation < Designed & Manufactured in Germany < ISO 900 certified quality management < Long term availability < Rugged solution (coating, sealing, underfilling on request) < RoHS compliant < Operating temperature: -40 C to +85 C industrial temperature range < Storage temperature: -40 C to +85 C, max. gradient 5 C/min < Humidity 5%... 95% RH non condensing < Altitude -300m m < Shock 5g 0.33ms, 6g 6ms < Vibration g 5-000Hz < MTBF tbd years < EC Regulations EN550, EN5504, EN (UL60950-/IEC60950-) EKF -4- ekf.com

5 Configuration Switches Operation Mode Configuration DIP Switches ( = Port, = Port ) EKF Part No ON =OFF =* digital output to front connector (-D) A D F R =ON =OFF analog () output, routed to rear I/O connector =ON =ON analog output to front connector (-A or ) A = analog D = digital F = Front I/O R = Rear I/O DDC Routing Configuration DIP Switches (3 = Port, 4 = Port ) EKF Part No ON =OFF =* DDC derived from monitor attached to front panel E M R P =ON =OFF =ON =ON DDC derived from optional on-board EEPROM programming mode via I C (future characteristic) DDC derived from optional on-board EEPROM normal operation mode (future characteristic) E = EEPROM M = monitor R = run (normal operation) P = Program EEPROM EKF -5- ekf.com

6 Block Diagram OUT IN OUT Front Panel I/O SN65DP59 -D Lane 0-3 Simplified Block Diagram CVX- CompactPCI Classic DisplayPort to EKF ekf.com F/P SEL -A DP to PTN3355 Lane 0/ DP++ MUX : HD3SS5 SEL DP++ SEL MUX : HD3SS5 Lane 0/ -A DP to SEL F/P PTN3355 on-board Components IC GPIO IC AddrTrans MUX GPIO IC -D Lane 0-3 SN65DP59 J CompactPCI Option J CompactPCI EKF -6- ekf.com

7 Assembly DRT CVX- Dual DisplayPort to / Converter CompactPCI Classic EKF J DP DP DPX DPX DRT CFG CFG upper F/P F/P lower EEP MON EEP MON 3 CFG3 CFG4 4 - / Select 3-4 DDC Select mdp IC mdp IC AMP EI Power Options Stand-Alone CFG5 5 CFG6 CFG7 6 7 IC Setup AMP MATE- N-LOK Option J CPCI CVX- CompactPCI Classic EKF ekf.com Option DRT CVX- Dual DisplayPort to / Converter CompactPCI Classic EKF J DP DP DPX DPX DRT CFG CFG upper F/P F/P lower EEP MON EEP MON 3 CFG3 CFG4 4 - / Select 3-4 DDC Select mdp IC mdp IC AMP EI Power Options Stand-Alone CFG5 5 CFG6 CFG7 6 7 IC Setup AMP MATE- N-LOK Option J CPCI CVX- CompactPCI Classic EKF ekf.com EKF -7- ekf.com

8 Front Panel O U T O U T S P G S mdp IN IN EKF draft - do not scale ekf.com S P G S mdp IN IN O U T O U T CVX- CVX- Please note: connectors available as ordering option only R/G/B Status LEDs S PG S dedicated to upper video port digital mode: I C controlled (future) analog mode: OnePixel monitor I C controlled (future) or power good (stuffing option) dedicated to lower video port digital mode: I C controlled (future) analog mode: OnePixel monitor EKF -8- ekf.com

9 mdp Screw Lock Option Option Front Panel Retainer Plate for mdp Cable Connectors EKF Part # 70.9.MDP. Description H-style retainer plate knurled-head screw washer xx.0 part # xx depends on required length 44..0xx (alternate parts) inside/outside threaded hexagon bolt must meet size of mdp cable connectors or inside/inside threaded bolt plus screw EKF -9- ekf.com

10 CPU Card to CVX- Interconnect Recommended mdp Cable Assemblies EKF Part # Description m Mini DisplayPort (mdp) to Mini DisplayPort (mdp) plug to plug cable assembly, VESA DisplayPort. suitable e.g. for CPU Boards PC3-ALLEGRO PC4-PRESTO PC5-LARGO SC-ALLEGRO SC-PRESTO SC3-LARGO m DisplayPort (DP) to Mini DisplayPort (mdp) plug to plug cable assembly, VESA DisplayPort. suitable e.g. for CPU Boards PC-GROOVE PC6-TANGO SC4-CONCERTO SC5-FESTIVAL EKF -0- ekf.com

11 mdp Input Connectors (Sink-Side) Mini DisplayPort / (Video Input) Conforming to Vesa Sink-Side Configuration 0 Power Out ) 9 GND 8 AUX_CH(N) 7 LANE(P) Mini DisplayPort EKF ekf.com 6 AUX_CH(P) 5 LANE(N) 4 GND 3 GND LANE0(P) LANE(P) 0 LANE0(N) 9 LANE(N) 8 GND 7 GND 6 CONFIG 5 LANE3(P) 4 CONFIG 3 LANE3(N) Hot Plug Detect GND ) +3.3V via electronic power switch.5a It is recommended to use only VESA compliant cable assemblies, which provide no connection with respect to DP/mDP connector pin 0 (power output). Some manufacturers however offer proprietary cables which pass through the pin 0 in addition, maybe for powering external devices via cable. This may cause a backdriving current however between VESA compliant DP ports. EKF -- ekf.com

12 Output Connectors / (Video Output) 7 TX0-9 TX- TX- 8 TX0+ 0 TX+ TX+ 9 GND GND 3 GND 0 TX5- TX3-4 TX4- TX5+ 3 TX3+ CEC ) 5 TX4+ GND 4 DDC_POW ) 6 DDC_SCL 3 TXC+ 5 GND 7 DDC_SDA 4 TXC- 6 _HP 8 VSYNC c3 BLUE c RED c6 GND c5 GND c4 HSYNC c GREEN ) +5V via self resetting fuse 0.5A ) CEC (stuffing option) The receptacles are provided with full (dual link) contacts. Nevertheless a single link cable is sufficient for operation (dual link cable assembly optional). As an option, the receptacles may be replaced by classic style connectors (ordering option). EKF -- ekf.com

13 Connectors (Option) HD-Sub 5-Pos. (Option) RED GREEN 3 BLUE 4 NC GND 6 GND 7 GND 8 GND 9 DDC_POW ) 0 GND 6 NC _DDC_SDA 3 HSYNC 4 VSYNC 5 _DDC_SCL ) +5V via self resetting fuse 0.5A As an alternate to the optional on-board connectors, adapters to can be used externally (picture below). EKF -3- ekf.com

14 CompactPCI Peripheral Slot Connector J The CVX- is powered from the CompactPCI backplane connector J (+5V only). In addition, some on-board configurations can be controlled via the I C SMBus I/F. #J A B C D E 5 +5V REQ64# ENUM# +3.3V +5V 4 AD +5V VI/O AD0 ACK64# V AD4 AD3 +5V AD AD7 GND +3.3V AD6 AD5 +3.3V AD9 AD8 M66EN C/BE0# 0 AD GND VI/O AD AD V AD5 AD4 GND AD3 8 SERR# GND +3.3V PAR C/BE# V IPMB SCL IPMB SDA GND PERR# 6 DEVSEL# GND VI/O STOP# LOCK# V FRAME# IRDY# BD_SEL# TRDY# 4 3 Not Keyed AD8 AD7 AD6 GND C/BE# 0 AD GND +3.3V AD0 AD9 9 C/BE3# IDSEL AD3 GND AD 8 AD6 GND VI/O AD5 AD4 7 AD30 AD9 AD8 GND AD7 6 REQ# GND +3.3V CLK AD3 5 BRSVPA5 BRSVPB5 RST# GND GNT# 4 IPMB PWR HEALTHY# VI/O INTP INTS 3 INTA# INTB# INTC# +5V INTD# TCK +5V TMS TDO TDI +5V -V TRST# +V +5V pin positions printed grey: not connected TDO - TDI internally connected EKF -4- ekf.com

15 CompactPCI Rear I/O Connector J The rear I/O connector J is stuffed as an option only. In order to avoid damages, before installing the CVX- with the J populated, ensure that your system is not equipped with a P CompactPCI 64-bit expansion backplane. Otherwise, permanent damage to the board or to system components could occur. #J A B C D E GA3 GA GA GA0 GND --RED --HSYNC --VSYNC 0 GND --BLU GND -DDC-SCL 9 GND GND GND --GRN -DDC-SDA 8 -_RED -_GRN -_HSYNC GND -_VSYNC 7 -_BLU GND 6 -DDC_SCL GND -DDC_SDA 5 4 GND GND V 4 +5V GND 3 GND GND The signal assignment of the optional J connector matches the rear I/O transition boards CCR- and CCT- with respect to -. EKF -5- ekf.com

16 Stand-Alone Power Connectors (Option) POWCON/ (Option) # /3 EI-Series Header Hrz/Vrt EKF ekf.com AMP EI-Series +5V GND 3 GND 4 +V Connector POWCON3 (Option) +5V Power MATE-N-LOK EKF ekf.com +V 4 3 GND AMP MATE-N-LOK 3 GND 4 +5V EKF -6- ekf.com

17 High Performance Embedded Industrial Computers Made in Germany boards. systems. solutions. EKF Elektronik GmbH Philipp-Reis-Str. 4 (Haus ) Lilienthalstr. (Haus ) HAMM Germany Phone +49 (0)38/ Fax +49 (0)38/ Internet sales@ekf.com