Energi Savr Node for DALI QSNE-2DAL-D DALI Fixture Controller V. Photo

Transcription

1 UTRO R UTRO R ode for E-2DA-D Fixture Controller ode for The ode unit is a DI-rail mounted controller for -compliant digital addressable loads. It provides bus power and control for two independent buses with up to 64 compliant digital addressable loads each. The ode unit also provides direct connections and power for the following utron devices: upancy sensors Daylight sensors receivers devices Features Provides power for two buses of -compliant digital addressable loads. 128 ma guaranteed current, 250 ma maximum supply current per bus. Each Bus can control a maximum of 16 zones. Power failure memory retains control unit programming in the event of a power loss. Default configuration requires no commissioning. Four occupancy sensor inputs for automated control of lights in areas. Four daylight sensor inputs automatically adjust light levels based on the amount of natural light entering through the windows. Hi Temp ode for Test E-2DA-D Power 230 V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) h Four receiver inputs for personal control. Add more occupancy sensors, daylight sensors, or receivers by connecting Modules (Ms). Includes link for seamless integration of lights, motorized window treatments, control stations, and Modules. ode units and Modules can be used in a Quantum system to control and manage light in an entire building. Transmitter UTRO One input group shown; connections available for up to four input groups. Bus 1 Bus 2 seetouch Wallstation Control gear Quantum Panel Contact Closure Interface Up to 64 -compliant digital addressable loads on each loop GRAFIK V~ ode unit Eye Control Power ode unit Up to 100 ink Ethernet Programming ink Wired Receiver Wired Daylight Wired upancy Radio Powr Savr upancy (up to 10 per M) Pico Wireless Controller (up to 10 per M) Wireless munication Control gear M Control gear Control gear Transmitter total devices ote: Multiple Ms can be added to increase the number of wireless sensors and Pico wireless controllers. Radio Powr Savr Daylight (up to 10 per M) Wired Daylight s* UTRO * Up to 4 wired sensors total (of any type) Wired Receivers* Wired upancy s* Power Supply

2 ode for E-2DA-D Fixture Controller Typical Application: Requires commissioning h Open Offices Corridor Private Offices Open Offices Corridor Private Offices seetouch Wallstation seetouch Wallstation ink ink Window Window Window Window Window Window UTRO Daylight Daylight Daylight UTRO Daylight Bus oop oop Bus upancy upancy upancy upancy upancy upancy upancy upancy Bus oop ink ink Bus oop upancy Daylight upancy Daylight upancy Daylight upancy Daylight oop Bus upancy Daylight upancy Daylight UTRO UTRO UTRO oop Bus seetouch Wallstation seetouch Wallstation ode ode unit ink ink ode ode unit

3 UTRO ode for E-2DA-D Fixture Controller Simple Applications: Preconfigured modes require no commissioning h Bus 1 Bus 2 Bus 1 ode unit Wired to input group 1 ode unit Window Wired to input group 4 Window upancy Daylight upancy Bus 2 Window Window upancy Wired to input group 2 Perimeter Interior Perimeter Interior Preconfigured Mode 1 Perimeter Daylighting * Four fixtures shown on Bus 1 and eight fixtures shown on Bus 2, however, up to 64 fixtures can be connected per bus. Preconfigured Mode 2 Two Zones with upancy s * Six fixtures shown on each bus, however, up to 64 fixtures can be connected per bus. Default Behavior for Connections upancy Daylight Connected to input group 1 Controls Bus 1 only Controls Bus 1 only Connected to input group 2 Controls Bus 2 only Controls Bus 2 only Connected to input group 3 Controls both Buses Controls both Buses with equal daylight gain Connected to input group 4 Controls both Buses Controls both Buses with lower daylight gain on oop 2 Troubleshooting and Maintenance Features Maintains redundant memory of control gear programming for ease of single or multiple control gear replacement. After installation, "TEST" button verifies wiring on all fixtures. Status EDs verify connections to control stations and sensors. After installation, ode unit identifies control gear communication failures.

4 ode for E-2DA-D Fixture Controller Specifications Power V~ 50/60 Hz, max current draw 100 ma ightning strike protection meets ASI/IEEE standard Can withstand voltage surges of up to 6000 V~ and current surges of up to 3000 A. Bus Output: 18 V- 128 ma guaranteed supply current, 250 ma maximum supply current per bus. Standards IEC certified (for units shipping after January 19, 2018) utron Quality Systems registered to ISO 9001:2015. For commercial use, Class A only. Control Gear patibility -2 certified; patible with control gear (e.g. ED drivers). The E-2DA-D is a single master controller and therefore no other controllers may exist on the same bus. Environment Ambient Temperature Operating Range: 0 ºC to 40 ºC. Relative humidity: less than 90% non-condensing. For indoor use only. Terminals Mains wiring: 1.0 mm 2 to 4.0 mm 2 Bus Wiring: 0.5 mm 2 to 4.0 mm 2 ink Wiring: 0.5 mm 2 to 4.0 mm 2 Input Wiring: 0.5 mm 2 to 2.5 mm 2 Mounting Intended to mount within an IP20 (minimum) rated consumer panel or breaker panel with integrated DI rail and dead cover. Width = 9 modules (161.7 mm). For more information on mounting and installation in panels with integrated DI rail see utron P / at h Programming Requirements An Apple ipod touch or iphone mobile digital device with the app is required for programming ode systems. The app is available from the App Store online store. The app cannot be used to program the ode units when installed as part of a Quantum system. The Apple ipod touch or iphone communicates with the ode unit via a WiFi router (not included). See the Programming Options section for further information. Buses Up to 64 compliant loads on each bus can be addressed and grouped into 16 zones. ode unit supplies a maximum of 250 ma to power each bus. ode unit supplies a guaranteed current of 128 ma to power each bus. ode -2 controller has an integrated bus power supply with polarity indicated on the unit. Some loads may be polarity sensitive; refer to individual manufacturers specifications for proper connection to the bus. Short circuit protection with automatic re-start ink imits A link can have up to 100 zones (outputs) and 100 devices. Each ode unit counts as one device toward the 100 device limit. Each assigned zone counts toward the 100 zone limit. Each ode (E-2DA-D) unit can supply 3 power draw units. Refer to the ink Power Draw Units specification submittal (utron P/ ) for more information concerning Power Draw Units. ink imits: 100 wired or wireless occupancy sensors. 100 wired or wireless daylight sensors. 100 wired wallstations or Pico wireless controllers.

5 ode for E-2DA-D Fixture Controller s Connected to the ode Unit Power Supply Outputs (4) ma maximum. - An auxiliary power supply must be used if the device requires more than 50 ma. upancy / Vacancy s Use vacancy sensors to automatically turn the lights off in an area a fixed time after it becomes vacant. Use occupancy sensors to automatically turn the lights on in area when it becomes occupied and to automatically turn the lights off in an area a fixed time after it becomes vacant. Four occupancy sensors can connect directly to the ode unit. Each area's occupied level and unoccupied level can be programmed. upancy sensor must provide a dry contact closure or solid-state output. Daylight s utron daylight sensors allow daylight harvesting with programmable gain settings in up to four gain groups per area. Four daylight sensors can connect directly to the ode unit. Controls Use utron receivers or wired Pico keypads for personal control of individual lighting zones. Four devices can connect directly to the ode unit. Other System ponents h M ( Module) - Integrating Wired and Wireless Inputs Use the M to integrate Radio Powr Savr upancy / Vacancy sensors, Radio Powr Savr Daylight sensors, and Pico Wireless Controllers to control zones on the ode unit. Assign up to 10 Radio Powr Savr upancy / Vacancy sensors per ode unit via M. Assign up to 10 Radio Powr Savr Daylight sensors per ode unit via M. Assign up to 10 Pico Wireless Controllers per Energi Savr ode unit via M. Add additional wired and wireless inputs by adding Modules to the link. Wire and power up to 4 wired inputs (of any type) total Daylight sensors upancy sensors Infrared () receivers The Radio Powr Savr sensors and Pico Wireless Controllers associated with the M should be mounted within 18 m line of sight, or 9 m through walls, of the M. Refer to M Specification Submittal (utron P/ ) for more information. seetouch Controls seetouch wallstations can be configured to control ode unit zones. Select one of 16 scenes and off in ode unit areas. Control individual lighting zones in ode unit areas. Each ode unit can power up to three seetouch controls. ED indicator displays the status of programmed lights.

6 ode for E-2DA-D Fixture Controller Other System ponents (continued) munication with GRAFIK Eye control units ode unit zones can be configured to respond to GRAFIK Eye scene buttons when associated with the GRAFIK Eye. ode unit zones can be configured to respond to scene commands initiated by the GRAFIK Eye astronomic time clock when associated with the GRAFIK Eye. ode unit operates in afterhours mode when associated with a GRAFIK Eye that is in afterhours mode. munication with E-IO ode unit zones respond to scene commands initiated by the E-IO in scene selection mode or occupancy sensor mode. ode unit can be configured to respond to zone toggle or occupancy sensor commands initiated by the E-IO in zone toggle mode or occupancy sensor mode. munication with E-CI-WK-E Integrate ode units with touchscreens, PCs, A/V systems or other digital systems and devices h

7 ode for E-2DA-D Fixture Controller Mechanical Dimensions h Hi Temp Test Power ode for E-2DA-D 230 V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) 89.7 mm mm 60.6 mm

8 ode for E-2DA-D Fixture Controller Overview of Wiring Terminals h Inputs PEV ink Ethernet Programming Port Bus 1* Bus 2* Hi Temp Test Power ode for E-2DA-D 230 V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) Mains Wiring * Wire according to local codes.

9 ode for E-2DA-D Fixture Controller Wiring: Mains Voltage h Hi Temp ode for Test E-2DA-D UTRO1 2 2 Power 230 V~ 50/60 Hz 100 ma 0,5 m (5 in-lbs) Wiring from Distribution to Bus Supply Turn off breaker at distribution panel. Run line, neutral, and wires from a V~ EEA 50/60 contact address: Hz feed + to - the + Energi - Savr ode unit. Emergency ighting Applications Hi Temp ode for Use normal (non-essential) power only. Test E-2DA-D When normal power UTRO1 drops out, the ode unit will not power the buses. When this occurs, Power 230 V~ 50/60 Hz 100 ma control gear powered from emergency feeds go to 0,5 m (5 in-lbs) their emergency mode (full light output by default). Mains Wiring and ow Voltage Separation The ode unit is designed to separate mains wiring from PEV circuits. Follow appropriate local and national codes to avoid violating required separation guidelines. Distribution Panel Earth/Ground eutral Mains/ine

10 ode for E-2DA-D Fixture Controller Wiring: Bus h Hi Temp ode for Test E-2DA-D Power Bus 1 DA 1 - DA V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) Bus 2 DA 2 + DA 2 - The ode unit will supply power to an independent bus, which supports a maximum of 64 -compliant digital addressable loads per bus. Wiring wiring is not SEV. wiring is treated as mains voltage, and thus may be run within the same sheathing. Ensure that there is no greater than a 2 V~ drop between the ode unit and the end of the Bus. Consult all national and local electrical codes for separation requirements. Maximum -compliant Wire Gauge Bus Wire ength 1.5 mm m 0.75 mm m 0.50 mm m UTRO1 in-lbs)

11 ode for E-2DA-D Fixture Controller Wiring: ink Hi Temp ode for Test E-2DA-D Power 230 V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) IEC PEV ink Wiring ink communicates using IEC PEV wiring h Follow all applicable national and local codes for proper circuit separation and protection. Wiring may be daisy chained or t-tapped. Total length of link must not exceed 610 m. st Temp wer ode for E-2DA-D 230 V~ 50/60 Hz 100 ma (1) (2) - (3) (4) ink Wiring ength ess than 153 m 153 m to 610 m 0,5 m (5 in-lbs) UTRO1 Available from Wire Gauge utron in one cable: Power (terminals 1 and 2): 1 pair 1.0 mm 2 GRX-CB-346S Data (terminals 3 and 4): 1 pair 0.5 mm 2, twisted and shielded (non plenum) GRX-PCB-346S (plenum) Power (terminals 1 and 2): 1 pair 4.0 mm 2 GRX-CB-46 (non plenum) Data (terminals 3 and 4): 1 pair 0.5 mm 2, twisted and shielded GRX-PCB-46 (plenum) Use one, twisted-shielded pair of 0.5 mm 2 for data link (, _).

12 ode for E-2DA-D Fixture Controller Wiring: ink (continued) h Only terminals 1, 3, and 4 connected between devices that supply PDUs Terminal 2 EVER connected between devices that supply PDUs All 4 terminals connected to link devices that consume PDUs + Terminal 2 (+) EVER connected* Terminal 2 (+) EVER connected* Devices that supply PDUs ink; no terminal 2 ode unit Devices that consume PDUs ink; all 4 terminals ink; all 4 terminals Input/ Output Interface Wired Keypad M ink; no terminal 2 ode unit Wired Keypad M M Terminal 2 (+) EVER connected* ** ink power supply ink; all 4 terminals Wired Keypad Input/ Output Interface Wired Keypad ink Wiring Rules * Terminal 2 (+) should EVER be connected between devices that supply PDUs. ** For ink power supply wiring connection details, refer to the installation instructions for the specific power supply model being used.

13 UTRO R UTRO R ode for E-2DA-D Fixture Controller Wiring: IEC PEV Inputs Electrical Contractors and Engineers All sensor wiring is IEC PEV. Follow all applicable national and local codes for proper circuit separation and protection. IEC PEV input terminals accept 0.5 mm mm 2 solid conductors. Mains voltage and IEC PEV wiring must be kept separate. Wiring Instructions Turn off circuit breaker or isolator at distribution panel. upancy Connect three conductors to three terminals as shown. One occupancy sensor can be wired to each input group. must be placed within 30 m of the ode unit. Receiver Connect the three conductors to the three terminals as shown h Receiver (continued) Receiver must be placed within 30 m of the Energi Savr ode unit. One Receiver can be wired to each input group. If a daylight sensor and receiver are connected, do not connect the daylight sensor's output (white wire). Daylight Connect the four conductors to the four terminals as shown. Terminals: Red = - White = Black = mon Yellow = Daylight Daylight must be placed within 30 m of the ode unit. One daylight sensor can be wired to each input group. Consult the daylight sensor specification sheet (utron P/ ) to properly locate the sensor. Do not place the sensor above pendants, fixtures, directly below lighting fixtures, or within skylight wells. * ote: Only one device may be connected per input group. If the signal from a daylight sensor is connected, another control may not be connected to the same input, and vice-versa. ** Connect the gray wire on -R upancy models. - Receiver * Daylight upancy mon Group 1 shown Transmitter Daylight/ * Yellow Red UTRO Black White* upancy Red Blue/Gray** Black Group 2 shown Transmitter - Receiver * Receiver* Red White* Black mon Hi Temp Test Power ode for E-2DA-D 230 V~ 50/60 Hz 100 ma UTRO1 0,5 m (5 in-lbs) OTE: There are four sensor groups. Each group wires the same and is shown above. Group 1 Group 3 Group 2 DA 1 DA Finsbury 1 2Pavement, 4th floor 2 Group 4 SPECIFICATIO Hi Temp SUBMITTA Test ode for E-2DA-D Power 230 V~ 50/60 Hz 100 ma Hi Temp ode for DA Test UTRO1 Power E-2DA-D 230 V~ 50/60 Hz 100 ma 0,5 m (5 in-lbs) lutron.co

14 ode for E-2DA-D Fixture Controller Programming Options Programming with Apple ipod touch or iphone Use the intuitive programming application for the Apple ipod touch or iphone to program systems with multiple ode units and Ms on the link h ode unit Dedicated Ethernet Connection for ode units* * ote: ode units are not designed to exist on an open network. Connection to an open network could result in reduced performance and Ethernet connectivity issues. 2 M Wireless Router (by others) Apple ipod touch or iphone mobile digital device Wire types: 1 ess than 153 m: utron cable GRX-CB-346S 153 m to 610 m: utron cable GRX-CB-46 2 Standard CAT5/CAT5E cable: Total length not to exceed 100 m 1 ink ink 1 Wireless router only required for programming with an Apple ipod touch or iphone. Wireless router may be removed for normal operation. Ethernet connection may be made via integral Ethernet jack. utron recommends that integral Ethernet jack be wired to an Ethernet jack in the space for ease of access and proximity to power for the wireless router. Works with any standard wireless router that supports multicast packets. Apple ipod touch or iphone can program all ode units connected to the link (except when part of a Quantum system). app is required and is available from the Apple App Store online marketplace. utron Qualified Control Gear utron requires that all devices that are intended to be used with a utron controller must be pre-tested by utron and determined to be compatible before being used on a project. For a complete list of utron qualified ballasts please refer to Application ote #482 (utron P/ ) for more information. )utron, utron, Quantum, Pico, GRAFIK Eye, and seetouch are trademarks of utron Electronics Co., Inc., registered in the U.S. and other countries. ode and Radio Powr Savr are trademark of utron Electronics Co., Inc. Apple, iphone, and ipod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.