Light Management Hub. Quantum 230 V CE Light Management Hub. Centralized Control Equipment

Transcription

1 Quantum 69-77b 06.. Hub The Quantum light management hub provides a centralized connection point for Lutron QS devices, including Energi Savr NodeTM, GRAFIK Eye QS, Sivoia QS shades, and Lutron dimming and switching panels. Features Designed to control, manage, and monitor digital addressable ballasts, Lutron power panels, GRAFIK Eye QS, Energi Savr NodeTM QS, and Sivoia QS shade systems in a building or whole campus. Supports both astronomic and time-of-day events to automatically control the lights and shades in the system. Simple reconfiguration of a space without rewiring. Individually control, monitor, and adjust any light or shade in a space. QS control links are topology-free. Panel Capabilities ing management panels communicate via an Ethernet connection using multicast protocol. Each hub supports up to Quantum processors with total of links each that can be individually configured to comunicate with: - Lutron power panels - Lutron QS devices

2 Quantum Specifications 69-77b 06.. Regulatory Approvals CE Power Input voltage: 0-0 V, normal/emergency feed 50 / 60 Hz 0 A Output: Processor - V A per link 8 BTUs/hr Physical Design Enclosure: IP-0 protection Weight: 0. kg Mounting Surface mount only Environment For indoor use only 0 ºC to 0 ºC Relative humidity less than 90% non-condensing

3 Quantum How to Build a Model Number Example QP - P0CSE - 0 Panel Type Number of Processors Accessing Device Voltage Available Model Numbers Contact Lutron for options not listed below. QP-P0CSE-0 QP-P0CSE-0 Panel Type QP = Quantum Hub Number of Processors P = Quantum processor P = Quantum processors Accessing Device SE = 5-port unmamaged Ethernet switch Voltage 0 for 0-0 V Additional Ratings 50 / 60 Hz Output: Processor - V A per link 69-77b 06.. Note: this panel is rated for Class A, Commercial Use Only.

4 R R Quantum Dimensions All dimensions in mm b Top View Left Side View Front View Right Side View Bottom View

5 Quantum Mounting and Conduit Entry Notes Water damages equipment. Mount in a location where the panel and processors will not get wet. Mount within 7 of true vertical. A minimum of 05 mm unobstructed space is required in front of and below the panel for ventilation b Ceiling Dedicated feed Mains voltage only IEC PELV / NEC Class wiring only for control links and Ethernet connection Alternate IEC PELV / NEC Class entry Alternate IEC PELV / NEC Class entry Wall Alternate IEC PELV / NEC Class entry Front View Side View

6 Quantum Panel Overview Mains voltage input, normal/emergency feed 69-77b IEC PELV / NEC Class barrier Receptacle (for Lutron service use only) Panel power switch IEC PELV / NEC Class power supply board IEC PELV / NEC Class configurable link wire trough Unused (no connect) Configurable links (power panel or Lutron QS link) Processor LEDs 5-port unmanaged Ethernet switch Quantum processors ( maximum)

7 Quantum Line Voltage Wiring PE N 69-77b V N/E Receptacle for Lutron Service use only Protected Earth (green) Neutral (blue) Line (brown) Notes Mains voltage must enter hub from top right of hub. Run a dedicated 0-0 V normal/emergency feed. Run wiring so mains line voltage is separate from IEC PELV / NEC Class wiring. Wire Sizes Power feed (live):.5 to.0 mm

8 Quantum Quantum Ethernet Wiring Example of Ethernet Wiring: Riser Diagram 69-77b Quantum Hub Floor Quantum Hub Floor Ethernet switch Quantum Hub Quantum Hub To additional Notes Ethernet wiring is considered IEC PELV / NEC Class, keep Ethernet wiring away from mains voltage wiring. Wiring distance for any single Ethernet data link segment is 00 m maximum; use switches or hubs for longer distances. Processors cannot be more than 6 Ethernet hops away from the server. Processors communicate over the Ethernet network using multicast UDP; a dedicated network is recommended for the lighting control system. Wiring between Hubs on a floor must be installed before startup. Wiring between floors can be added later. Floor Quantum Hub Unmanaged Ethernet switch Quantum Hubs Quantum server

9 Quantum 69-77b Configurable Link Wiring: Power Panel Link Processor link terminal Power panel Power panel Power panel DRAIN V+ COM 5 COM N/C D DRAIN 5 Sense line COM N/C D DRAIN 5 Sense line COM N/C D DRAIN 5 Sense line Unused Link terminator (LT-) Configurable links Control wiring ().5 mm : Common Data link () shielded, twisted pair.0 mm : : D: Drain wire in shield (keep away from ground and all electronics) Power Panel IEC PELV / NEC Class Terminal Wiring ().5 mm Drain Data link: twisted, shielded pair.0 mm : : Sense:.0 mm Link terminator (LT-) Emergency/essential sense line ().0 mm 5: Sense line Sense line is used when there is a panel being supplied by an emergency/essential feed Notes Power panel link must be daisy-chained (no T-taps). Maximum of power panels per link. It is not necessary to have the Quantum hub at the end of the link. The sense wire (terminal 5) is used whenever there is a panel being supplied by an emergency/essential feed; see power panel instructions for details. Each IEC PELV / NEC Class terminal can accept only two.0 mm wires. Two.5 mm conductors will not fit. Connect as shown using appropriate wire connectors. D 5 C D Common VFW Data A OK Drain Sense Link A B Power OK Link Comm Data B OK D 5 C D S ELECT C IRCUIT Drain Total length of control link may be no more than 600 m. If link repeater interface and GRX-CBL-6L cable are used, length may be up to 00 m. IEC PELV / NEC Class wiring cable is available from Lutron (GRX-CBL-6L) and contains two.5 mm conductors for control power, one twisted, shielded pair of.0 mm for data link, and one.0 mm conductor for emergency (essential) sense line.

10 Quantum 69-77b Configurable Link Wiring: GRAFIK Eye QS and Sivoia QS Shades DRAIN V+ COM 5 GRAFIK Eye QS Link (Drain wire in shield - Connect together to make one continuously linked shield. Keep away from ground and control electronics.) GRAFIK Eye QS control unit QS wallstations Unused Configurable links Note: Wallstations are powered directly from the light management hub (not the GRAFIK Eye QS control unit) IEC PELV / NEC Class Terminal Wiring IEC PELV / NEC Class control wiring ().0 mm : Common : V ().5 mm Sivoia QS Shade Link (Drain wire in shield - Connect together to make one continuously linked shield. Keep away from ground and control electronics.) DRAIN V+ COM 5 A B C GRAFIK Eye QS control unit 5 6 L N ().5 mm DRAIN wires Data link: () twisted, shielded pair.0 mm : : Sivoia QS shade Sivoia QS smart power supply panel Wire Gauge QS Link Max. Length.5 mm 600 m.5 mm 50 m.0 mm 50 m Notes System communication uses IEC PELV / NEC Class wiring. Follow all local and national electrical codes when installing IEC PELV / NEC Class wiring with mains wiring. Each terminal accepts up to two.0 mm wires. Total length of control link must not exceed 600 m; If exceeding 600 m, contact Lutron for wiring configuration. Make all connections in the control unit s wallbox. A Quantum QS link can have up to 5 switch legs (outputs), 99 devices, and power draw units (see page ). Wiring can be T-tapped or daisy-chained. Wire sizes: - Two.5 mm conductors for control power. - One twisted, shielded pair of.0 mm for data link. - Cable is available from Lutron: GRX-CBL-6L.

11 Quantum Configurable Link Wiring: Energi Savr NodeTM QS 69-77b 06.. Energi Savr NodeTM QS Link (Drain wire in shield - Connect together to make one continuously linked shield. Keep away from ground and control electronics.) DRAIN V+ COM 5 QSNE-DAL-D shown. QS terminal connections are identical regardless of model number. From right side of configurable links in panel QS wallstations Note: Wallstations are powered directly from the light management hub (not the Energi Savr NodeTM QS unit)