GSM GATE VT 10. version 7.0 and higher. Installation manual. VARIANT plus, spol. s.r.o., U Obůrky 5, TŘEBÍČ. Issued on January 10, 2012

Transcription

1 Gate VT 10 manual GSM GATE VT 10 version 7.0 and higher Installation manual VARIANT plus, spol. s.r.o., U Obůrky 5, TŘEBÍČ technik@variant.cz Issued on January 10, 2012 VARIANT plus s.r.o. VARIANT plus, spol. s r.o. page 1

2 manual Gate VT 10 For programming gate VT10 version 7.0 and higher you must use software VTGTsetup_v7 CONTENT 1.0 Description Specifications Signaling Installation Telephone line simulation Audio signal setup Programming via PC Communication with PC Password a Options Input setup Output setup Input and output labels System setup User controls Programming via SMS Expansion modules Description Gate VT10 can transmit messages via SMS, by ringing a phone number, by using acoustic signalization or by using GSM voice channel. The gate simulates a phone line to which a usual analog phone can be connected The telephone communicator can dial the monitoring station and transmit a 4/2 or CID message. The gate is equipped with 2 relay outputs, which can be activated by an SMS or by dialing its number. The gate can be enhanced with following expanders. Expander VT-01 4 inputs, 2 relay outputs Expander VT-02 6 relay outputs Expander VT-04 8 voice messages, 6 balanced inputs, 2 outputs, LED page 2 VARIANT plus, spol. s r.o.

3 Gate VT 10 manual 2.0 Specifications Feed 10 15V= Inputs 2 Temperature 10 až 55 C Input delay 100ms 5s Humidity max 85% Phone numbers 4 for each input (24 with expander) Consumption when idle 80mA Relay outputs 2, NO/NC Peak consumption 1A do 10 sec. Relay control SMS, ringing Programming PC or SMS Credit check up automatic, via SMS Feed check up down 11V Restart GSM via SMS LED1 Connector 12V IN REL1 REL2 for expander 1 2 NC 1 NO NC 2 NO + - LED4 LED3 LED2 SIM card Antenna 3.0 Signaling LED1 GSM line, signal power LED2 status gate LED3 a LED4 status outputs - relay RJ11 for PC + - LED Status Description blinks 1:1 the gate starting lights the gate is loading GSM net LED1 blinks 1x-4x + pause signal power 1x no signal 4x full blinks 9x + pause trouble with GSM blinks 3x per se ready for data trasnfers lights using phone line lights + flashing dialing is progress LED2 blinks 1:1 come call to VT blinks number of activating input 9 blinks calling from security panel OFF line is not using LED3 lights relay 1 is ON LED4 lights relay 2 is ON VARIANT plus, spol. s r.o. page 3

4 manual Gate VT Installation The gate is intended for indoor usage, where the temperature must not drop below minus 10 C. Under no circumstances can the gate be exposed to humidity. The constant consumption of 80mA and the installation conditions make the gate inappropriate for usage in cars. If you use the gate in security systems, install the gate directly into the casing of the alarm control panel or a stand-alone metal or plastic box. 4.1 Feed Only feed the gate from a source that is capable of covering 10s consumption of 1A. The best way is to connect the gate to an accumulator that is rechargeable. In security systems it is recommended to feed the gate directly from the auxiliary accumulator using a 2A fuse. Never supply the gate from the AUX of the alarm control panel. It will not manage to cover the feed needed and the functionality of the gate will not be reliable. Connect the 12V to the clamps as you can see in the picture. 4.2 Antenna The gate is equipped with a coaxial cable with the standard FME connector for GSM antennas. If you use a stick-on antenna it is necessary to install it in a sufficient distance from any metal objects. The distance is dependent on the strength of the signal in a given location. The minimum distance from the metal objects is 30cm the further the better. The antenna must not be attached to metal, e.g. the metal box. It also must not be closed in the metal box. In low signal locations it is recommended to use a high gain antenna, possibly a dipole directional antenna. 4.3 Telephone line, connection to PC The telephone line simulation contains also the simulation of the ringing and the dialing tone. Connect the phone as usual to the RJ11 connector. It is a 4-pin connector, the inner pins simulate the telephone line and the outer pins connect the gate to PC phone PC 3 canon 5 2 the PC. The telephone line has the same features as a usual analog telephone line. It is possible to connect a usual analog telephone or to connect the communicator of the alarm control panel to communicate with the monitoring station. Use the enclosed RJ11 COM converter to connect the gate to the PC. 4.4 Inputs If the input is idle and unlinked, it must be grounded during the activation. 4.5 Outputs The outputs are bipolar relays. com input 4.6 SIM The SIM card must not be PIN protected, the SMS centre must be set, the SMS confirmation off, and please delete all received or sent SMS messages. page 4 VARIANT plus, spol. s r.o.

5 Gate VT 10 manual 5.0 Telephone line simulation There is no need for any extra setup to simulate a telephone line. After you have completed the Start-up phase, is the line fully operational. It is possible to connect a usual analog telephone that facilitates the voice call transmission. BEWARE! It is only possible to use the gate to transmit voice, not fax and not any communication via modem. After the telephone is picked up, the notification tone will sound. If the module is not logged in the network or it is busy, the engaged tone will sound. If the gate is intended to transmit messages to the monitoring station from the alarm control panel, connect a cable to the RJ11 connector and connect the two middle wires to the RING and TIP clamps of the alarm control panel. Don t join any other wires; otherwise is the function of the gate not ensured. It is possible to connect an analog telephone to the clamps R-1 and T-1 of the alarm control panel to allow voice calls. It is not easy to say which transmission format is the best. The features of the GSM transmission are determined by the signal strength and the capacity of the transmitters in the area. These factors influence the quality of the transmission in the area and it is advisable to test all formats and then choose the most appropriate one for the given locality. To do these tests, it is vital to have and listen-in module. Therefore we recommend an affordable high-end listen-in module UCHO-1. The telephone number can t consist of more than 16 ciphers. If this limit is overstepped the dialing process is cancelled and the engaged tone sounds. It there is a 3s pause after the last dialed cipher, the gate begins to dial the number in to the GSM network. If it does not come the dialing of a number in 15s, the engaged tone sounds. VARIANT plus, spol. s r.o. page 5

6 manual Gate VT Audio signal setup It is possible to boost the telephone line clearness for formats intended for the monitoring station by adjusting the volume of the speaker and the sensitivity of the microphone used in the gate. It is necessary to ensure the needed signal strength without any distortion or echo. Theses factors substantially influence the quality of the transmission to the monitoring station. 6.1 Audio setup from the PC Description of the program can be found on the following page. Audio signal change can be exercised inside the program. You can se the default settings in the picture. 0 the weakest signal 9 maximum signal 6.2 Audio setup via telephone We can execute the audio setup of the speaker or the microphone via an external phone with DTMF option. The gate must be operational and equipped with a SIM card. We pick up the receiver and we hear the dialing tone. Output audio setup microphone Pick up the receiver of the connected telephone on the VT10 gate and input * data * command on the keyboard of the telephone. command data description default * data * min. signal 9 max. signal 3 Input audio setup speaker Pick up the receiver of the connected telephone on the VT10 gate and input # data * command on the keyboard of the telephone. command data description default # data * min. signal 9 max. signal 5 Recommended values: microphone: 3 4, speaker: 4 6 page 6 VARIANT plus, spol. s r.o.

7 Gate VT 10 manual 7.0 Programming via PC 7.1 Connection to PC The gate VT10 must be powered. Connect the enclosed RJ11 COM cable into the RJ11 connector on the gate and to the COM port on the PC. 7.2 Run software Open the CD and start VTGTsetup. Follow the instructions on the installation wizard. After instalation run the program, see the introductory dialog with the available versions: For gate VT10 version 7.0 or higher (actual) For gate VT10 version 6.X or older. VARIANT plus, spol. s r.o. page 7

8 manual Gate VT Communication with PC 8.1 Establishing the communication Choose the COM port on the PC that will be used for the communication. Load all value on PC to default. The module can t be switched into the programming mode immediately after connection to power, when sending/receiving SMS, when ringing or dialing. 8.2 Data transfer Data will be transmitted from the program to the gate VT10. The progress of the transmission is displayed in the pop-up window. After the data is written the automatic data control is initiated. If the examined data is identical to the data in the program, the transfer is interpreted as correct. If there is a difference between the examined data and the data in the program, the transfer is regarded as faulty. Date will be transmitted from the gate VT10 into the program. If there is no response from the gate, the transfer is interpreted as faulty. During the data transfer blinks the LED status and LED communication. 8.3 Backup Save changes on PC. Open previously saved settings. 9.0 Password a Options The Password must consist of 4 ciphers and the first one must not be zero. ( ) User password setup. It is needed for SMS control, input/output control and credit inquiry. Default 1234 Installation password setup. It is needed for gate programming via SMS. Default Optional features (for VT10 is available only option 5) 5. The functionality of the calling procedure is allowed. When the activation of an input the calling procedure is started (module is calling to the various phone numbers), the user can this calling procedure stop. When the user accepts the call from the module and then parallel calls are stopped. This functionality is enabled since the version FW page 8 VARIANT plus, spol. s r.o.

9 Gate VT 10 manual 10.0 Input setup You can set a response time for the inputs. The input activation must be longer than here set value * 50ms. The response time can be set in the interval of 50ms 5s. Default 4 = 200ms Cal type 4 telephone numbers are allocated to each input. The gate VT10 is equipped with 2 inputs. The following description is viable only if the EXPANDER is NOT used. SMS - maximum number of characters is 46. It is possible to divide the message into two messages with the : mark. The first one is sent during the activation and the second one during the deactivation. The : mark must not be used in the text of the SMS. Telephone number - in the usual or international format Type of calling: 1- A SMS only sent after the input activation. 2- Send a SMS and then ring a telephone number, after being received send a DTMF signal. Connection is correct when ringing during 4 seconds. 3- Only ring a telephone number, after being received send a DMTF signal. Connection is correct when ringing during 4 seconds. 4- A SMS only sent after the input activation. 5- Send a SMS and then ring a telephone number, after being received send a DTMF signal. Connection is correct when answer the phone to 2 seconds. 6- Only ring a telephone number, after being received send a DMTF signal. Connection is correct when answer the phone to 2 seconds. 7- Same as Same as Same as 6. A telephone number is dialed only during the activation. If the input is deactivated, only a SMS is sent if allowed. If an input is activated and it is allowed to dial a telephone number, this number will be dialed for approx. 20s. If the connection is not established, the number will be dialed 4x. If the dialed number rings or it is picked up at least for 5 seconds, it is regarded as a successful connection. During the ringing, the gate transmits a DTMF signal. VARIANT plus, spol. s r.o. page 9

10 manual Gate VT Features inputs - EXPANDERS Activation input is realized connecting or disconnecting to GND according to the value in the Expander. Without expander value 0 activated the inputs by connecting GND value 7 activated the inputs by disconnecting GND Input description Input 1 SMS / dial instant Input 2 SMS / dial instant System input 7 Testing SMS in interval 1 30 days (section 13.1) System input 8 Telephone 1 and 2 Power interruption transmission only SMS in format: POWER FAILURE : POWER RESTORATION. The power failure occurs if the power level drops below 11V for longer than 1 minute. The power restoration is determined as the voltage level above 11V lasting for 4 minutes. Telephone 3 low credit / forward SMS (section 13.3) Telephone 4 credit inquiry (section 13.3) Another expander modes 1, 2, 5, 8, 9 relating to the use of expansion modules (section 17) Output setup The condition of the outputs is saved in the module s memory. As a result the output settings reload if the power to the module is disconnected and reconnected later. Determine the function for the relay. 0 RELAY 1 and RELAY 2 are controlled via ringing or SMS 1 RELÉ 1 clipped if GSM network is not available RELÉ 2 controlled via ringing or SMS Here you can determine the length of the pulse (if the relay is activated by a pulse). 0 pulse not allowed, 1 9 sec. page 10 VARIANT plus, spol. s r.o.

11 Gate VT 10 manual 11.1 Output control by dialing It is possible to dial the gate to control outputs RELAY 1 and RELAY 2. Telephone numbers to which the gate will respond and which will serve to control the outputs are assigned to INPUT 9. Telephone number which can control the output by dialing. Relay which is by this phone number switched on. 1-8 relay on the module or on the expansion module A Two independent outputs are operated through one phone number. When the module VT10 will accept the call up to three ringings the relay 1 is switched on. When the call is accepted after 4 ringings the relay 2 is switched on. In the case that the outputs of main VT10 module are extended by the usage of the expansion module we can select the outputs for which the functionality described above is applied. The outputs are selected by the symbol #, for example #23# By this way we can edit the various authorizations for possible opening/closing gates, doors etc. When this functionality is selected the parameter TYPE OF SWITCHING is not significant. Type of switching determines how the output will react to the accepted call: Pulse relay will be switched on for a period predefined in the value PULS On relay is switched on Off relay is switched off Neg relay is denied On/off 2x ringings = relay will be switched on, 5 and more ringings: relay will be switched off (we ring from the phone number to pager and after the determined number of ringings we finish our call) With the exception of the type of switching on/off is the confirmation of the requirement from the side of pager done by the finalization of call after two or three ringings. The following tables for programming enable the edition of up to 200 phone numbers which are able to operate the relays.. VARIANT plus, spol. s r.o. page 11

12 manual Gate VT Wiring with external relay If the output control spool external relay, door lock relay or other direct current induction burden, it is necessary to this reel connect parallel diode in the termination direction. + Example: Input and output labels In this part of the program you can label the inputs and the outputs. If the condition of and input/output is inquired, a message about the particular input/output will be transmitted. INPUT OUTPUT 13.0 System setup Attention! INPUT 7, INPUT 8 and INPUT 9 are only virtual inputs and they serve to send messages about the system. These inputs are activated by system events and they are not routed to the terminal plate. page 12 VARIANT plus, spol. s r.o.

13 Gate VT 10 manual 13.1 Test message INPUT 7 The test SMS is transmitted in a period of 1 30 days. If you input 0 or a value higher than 30 the message will not be sent. The test SMS is transmitted from the INPUT 7. It can be sent to 4 different telephone numbers. It is only possible to use Type of call 1 sending SMS. It is not possible to transmit a voice call through this input. The call is executed in the time interval allotted. The timer is reset in these cases: end of programming via PC, after inputting TEST into the program via SMS, after attaching the power cable and logging in the GSM network Power failure INPUT 8 First and second position on input 8 are using to insert phone number where will be send SMS about failure of power supply. Type of ring choose 1, it could be using only SMS. If to divide the message into two messages with the : mark, format SMS is POWER FAILURE : POWER RESTORATION. Failure of power supply is down voltage under 11V during 1 minut. Restore of power supply when grow up voltage above 11V on 4 minutes Credit operations INPUT 8 In order to have access to credit operations it is necessary to input the appropriate number for credit information (depending on the provider) in the 4 th box on the Input 8. Type of call 1 must be selected. In order to check the credit we send an SMS in format: USER PASSWORD and letter K. The password is by default set to In this case the SMS looks like: 1234 K. This message will be received and the module learns the information about credit and sends the sum back. Automatic credit check + SMS forwarding The credit is checked every 24 hours. If the credit is too low, a warning is sent to the 3 rd number on Input 8. The type of call must be set to 1 or 2. Further description can be found in the following chapter. In view of various forms of services of GSM providers, the manufacturer is not responsible for proper operation of this process Přeposílání SMS zpráv VSTUP 8 tel. číslo 3 For the 3 rd telephone number we can chose following option for INPUT 8: Type of call 1 credit info Type of call 2 - sends SMS about credit and all SMS messages except for the operation messages. Type of call 3 only send SMS messages except for the operation messages. Only 70 characters are sent. The rest is deleted. VARIANT plus, spol. s r.o. page 13

14 manual Gate VT User controls The SMS messages are received by the TELIT module and the processor loads from the module every 30s. Therefore it is necessary to take into account that the longest delay between the transmission of the SMS and the reaction of the gate can be 30s. Every user SMS must start with a user password. It consists of 4 numbers and the first must not be 0. It is set to 1234 by default. The syntax for a user SMS is: USER PASSWORD COMMAND COMMAND COMMAND etc.. The maximum length of the message is 90 characters. Only capital letters are accepted. It is possible to write also several inputs / outputs. It is possible to sequence the commands RELAY output control and condition monitoring command value description example (user password is 1234) V 0 8 Output deactivation V2 0 it goes for all outputs 1234 V235 Z 0 8 Output activation Z0 0 it goes for all outputs 1234 Z1246 P 0 8 Pulse on the output it goes for all outputs 1234 P2 Pulse length is determined 1234 P456 in the box PULSE. N 0 8 Negation of outputs N5 0 it goes for all outputs 1234 N45 T K S N/A N/A N/A After receiving a command the telephone from which the SMS was received is dialed. The command can be used for check-up of commands. It sends back credit info. For further information see chapter Command S serves to learn the condition of all In/Outputs. The module sends back a message containing information about current condition of In/Outputs. See chapter V23 T (switches off outputs 2 and 3 and calls back) 1234 K 1234 S It is possible to include any text in front of the password to ensure quick orientation. SWITCH ON THE BOILER 1234 Z1 SWITCH OFF THE BOILER 1234 V1 Example: ANY TEXT 1234 V23 Z14 N5 S Switch off output 23 Switch on output 14 Negate output 5 SMS on condition of the inputs and outputs has been sent page 14 VARIANT plus, spol. s r.o.

15 Gate VT 10 manual 15.0 Programming via SMS We advise to program the gate using the PC. The SMS programming is appropriate for making smaller adjustments or to check current condition. The programming SMS starts with the installation password set by default to If you send an inquiry the gate sends back an SMS containing the current settings of the gate. Then you can edit the SMS and send it back to the gate. The gate adopts the changes adjusts the settings according to the SMS. Then the gate sends back a confirming SMS that contains the new settings. The advantage of this method is a minimal editing effort and maximal syntax control. The inquiry on the settings is in the form installation password Cx (4567 Cx) where x is the section number. The programming is divided into several sections. SECTION INFORMATION RETURNED 0 Installation password, user password, expander, arming, delay, test, sensitivity, relay, pulse 1 Input 1 settings (4 telephone numbers and SMS) 2 Input 2 settings (4 telephone numbers and SMS) 3 Input 3 settings (4 telephone numbers and SMS) 4 Input 4 settings (4 telephone numbers and SMS) 5 Input 5 settings (4 telephone numbers and SMS) 6 Input 6 settings (4 telephone numbers and SMS) 7 Input 7 settings (4 telephone numbers and SMS) 8 Input 8 settings (4 telephone numbers and SMS) 9 Input 9 settings (4 telephone numbers for relay activation via dialing) D pošle celkem 12 SMS zpráv informujících o celkovém nastavení EEPROM If we send: 4567 C0 We get back: 4567 G0 inst.i=4567 useru=1234 exp.e=0 arm.a=- delayz=4 test.t=0 senss=4 rel.r=0 pulsp=1 microphone M=3 speakern=5 We can now edit this message by altering the figures after = and send it back to the gate. After the gate carries out the task it sends back a confirming SMS that contains the new settings. VARIANT plus, spol. s r.o. page 15

16 manual Gate VT SMS section ratio to software SECTION 0 SECTION 1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SECTION 7 SECTION 8 SECTION SMS programming - Abbreviations and their meanings Abbreviations Description Identification inst. Installation password I user User password U exp. EXPANDER type E arm. -- A delay Incoming and outgoing delay Z test Interval of testing messages T sens. Input reaction time S rel. Relay function R puls Pulse length on output relays P microphone Microphone volume level M speaker Speaker volume level N Command for entering the programming section. The number of the section follows after the command. Command for send the current values section. The number of the section follows after the command. G C page 16 VARIANT plus, spol. s r.o.

17 Gate VT 10 manual 16.0 Expansion modules It is possible to connect only one expansion module to the gate VT10. After the module is connected it is necessary to input a relevant value in the box EXPANDER. There are two ways how to use the module due to the expander setup. 0 Without expander, activated the inputs by connecting GND 1 With expandér VT01, activated the inputs by connecting GND 2 With expandér VT02, activated the inputs by connecting GND 5 With expander VT-04, activated the inputs by connecting GND 7 Without expander, activated the inputs by disconnecting GND 8 With expandér VT01, activated the inputs by disconnecting GND 9 With expandér VT02, activated the inputs by disconnecting GND Arming: when YES is selected INPUT2 is activated and also INPUTS 3 and 4 on the expansion module but only in the case when INPUT1 is activated, too (the change of INPUT1 from the activated status to the peaceful status does not make any influence to the running transmission of INPUTS 2, 3 and 4). VARIANT plus, spol. s r.o. page 17

18 manual Gate VT VT-01 description We add 4 inputs and 2 relay outputs to the gate by connecting this module. The inputs are activated by connecting (modes 1) or disconnecting (modes 8) ground potential GND. It is recommended to use wires of maximum length of 1m (a shielded cable is appropriate). The function of the inputs and outputs is given by the set Expander value. This expander is used in modes 1 and EXPANDER 1 or EXPANDER 8 with module VT-01 Set the EXPANDER field on value: 1 activated by connecting 8- activated by disconnecting Only with module VT-01 Connection description: Inputs Ouputs Input 1 gate VT10 Input 2 Input 3 Input 4 module VT-01 Input 5 Input 6 Relay 1 gate VT10 Relay 2 module VT-01 Relay 3 Relay 4 page 18 VARIANT plus, spol. s r.o.

19 Gate VT 10 manual EXPANDER has value 1 The inputs are activated by connecting ground potential GND. Input 2, 3 and 4 may be depending on the input 1 (by setting the parameter Arming). Relay outputs are controlled via ringing or SMS. Input description Input 1 SMS / dial instant Input 2 SMS / dial instant Input 3 SMS / dial instant Input 4 SMS / dial instant Input 5 SMS / dial instant Input 6 SMS / dial instant System input 7 Testing SMS in interval 1 30 days (section 13.1) System input 8 Telephone 1 and 2 Power interruption transmission only SMS in format: POWER FAILURE : POWER RESTORATION. The power failure occurs if the power level drops below 11V for longer than 1 minute. The power restoration is determined as the voltage level above 11V lasting for 4 minutes. Telephone 3 low credit / forward SMS (section 13.3) Telephone 4 credit inquiry (section 13.3) EXPANDER has value 8 The inputs are activated by disconnecting ground potential GND. Input 2, 3 and 4 may be depending on the input 1 (by setting the parameter Arming). Relay outputs are controlled via ringing or SMS. Input description Input 1 SMS / dial instant Input 2 SMS / dial instant Input 3 SMS / dial instant Input 4 SMS / dial instant Input 5 SMS / dial instant Input 6 SMS / dial instant System input 7 Testing SMS in interval 1 30 days (section 13.1) System input 8 Telephone 1 and 2 Power interruption transmission only SMS in format: POWER FAILURE : POWER RESTORATION. The power failure occurs if the power level drops below 11V for longer than 1 minute. The power restoration is determined as the voltage level above 11V lasting for 4 minutes. Telephone 3 low credit / forward SMS (section 13.3) Telephone 4 credit inquiry (section 13.3) VARIANT plus, spol. s r.o. page 19

20 manual Gate VT VT-02 description By connecting this module we add 6 relay outputs controlled via SMS or dialing to the gate EXPANDER 2 or EXPANDER 9 with module VT-02 Input 1 Inputs Gate VT10 Input 2 Set the EXPANDER box to 2 Only with VT-02 module Connection description: Outputs Gate VT10 Module VT-02 Relay 1 Relay 2 Relay 3 Relay 4 Relay 5 Relay 6 Relay 7 Relay 8 Input description Input 1 SMS / dial instant Input 2 SMS / dial instant System input 7 Testing SMS in interval 1 30 days (section 13.1) System input 8 Telephone 1 and 2 Power interruption transmission only SMS in format: POWER FAILURE : POWER RESTORATION. The power failure occurs if the power level drops below 11V for longer than 1 minute. The power restoration is determined as the voltage level above 11V lasting for 4 minutes. Telephone 3 low credit / forward SMS (section 13.3) Telephone 4 credit inquiry (section 13.3) page 20 VARIANT plus, spol. s r.o.