16-Channel Digital Input Termination Card 24Vdc
|
|
- Ursula Dalton
- 6 years ago
- Views:
Transcription
1 TDI16AIA 16-Channel Digital Input Termination Card 24Vdc (TDI16AIA) Issue 3 October 2005 INTRODUCTION PURPOSE The TDI16AIA 16-channel digital input termination card acts as an interface between the digital signalling devices in the field device and the digital input circuits of an SC300E chassis. It provides: Screw terminal connectors for the field wiring Power supply inputs for the field devices Fuse protection for the field loops with local and remote indication of fuse failure Overvoltage and transient protection This document is intended to provide a general understanding of the function of the TAI16AIA, sufficient to enable basic maintenance operations to be effected in the field. ASSOCIATED DOCUMENTATION Reference Title MDI32BIS 32-Channel Digital Input Module User Manual PDD24 Power Distribution Panel User Manual
2 SPECIFICATION Model Power Supply inputs TDI16AIA Has two separate connectors (FS1and FS2) for redundant dc power supplies. The positive supplies feed a common bus via auctioneering diodes. When auctioneering takes place outside the card, the required power may be supplied via a single connector. No. of digital input channels 16 Nominal field supply voltage Maximum field supply voltage Current rating 24Vdc 33Vdc 50mA per channel. NOTE: In normal operation when used with a Digital Input Module having a 10k ohm input resistance, the current in each channel will be 2.4mA with 24V field supply. Fuse in each positive line to field Chassis cable connector Field cable connector Fuse blown indication 1A, fast acting, indicating 34 way DIN41612 Screw terminals to suit 2.5mm 2 wire (16AWG) Local: Fuse blown LED (one per card) Remote: Fuse blown alarm output (PL1) can be connected to Fuse blown LED on Power Distribution Panel (PDD24). Transient suppression Safety ground terminal TS1 Overall size (mm) Overall size (inches) Weight A transient suppressor device between each field return line and a common 0V bus clamps the field return line voltage (with respect to 0V common) as follows: +37Vdc to 1mA (maximum for continuous overload) 69A maximum peak pulse current for 8ms to 20ms M3 threaded bush provision for a ring terminal. Allows the common 0V supply bus to be grounded via a 10k ohm resistor. Prevents the channels from floating if the card is disconnected from the chassis 162L x 125W x 107H 6.4L x 4.9W x 4.2H 0.35kg 2 TAI16AIA October 2005 Issue 3
3 TDI16AIA 16-Channel D/I Termination Card 24Vdc ENVIRONMENTAL SPECIFICATIONS The maximum ambient temperature measured at the hottest point within the Triguard system shall not be greater than 60 degrees centigrade. Temperature operating: +5 C to +60 C Temperature storage: -25 C to +70 C Humidity: 5% to 95% non-condensing at ambient < 40 C EMC/RFI Immunity: Tested and certified to IEC 1131-Part Vibration/Shock: Tested and certified to IEC 1131-Part Certification: General Certification: Ref. SC300E TMR Product Guide (ref ). TRANSPORT AND HANDLING The termination card must be transported and stored in its original packing material which should be retained for this purpose. TDI16AIA October 2005 Issue 3 3
4 TECHNICAL DESCRIPTION PHYSICAL The TDI16AIA comprises a PCB assembly mounted in a moulded carrier that can be snapped onto all commercially available styles of DIN mounting rail. Connection to the chassis backplane is via a multicore cable terminated at either end by a DIN41612 connector. Figure 2-2 shows the TDI16AIA with the DIN41612 connector attached and mounted on rail EN type NS 35/5. Figure 2-1 identifies the main components on the PCB. Figure 2-1 General view and component layout 4 TAI16AIA October 2005 Issue 3
5 TDI16AIA 16-Channel D/I Termination Card 24Vdc Figure 2-2 Leading dimensions and mounting schematic TDI16AIA October 2005 Issue 3 5
6 Figure 2-3 Circuit diagram showing a single channel 6 TAI16AIA October 2005 Issue 3
7 TDI16AIA 16-Channel D/I Termination Card 24Vdc EXTERNAL CONNECTIONS Fixed Terminal Field terminals 1 to 16 (+) and 1 to 16 (-) Chassis connector J1 Field power supply inputs FS1 and FS2 Alarm output PL1 Ground terminal TS1 Details Screw terminals to suit 2.5mm 2 wire Connector, 34-way,DIN41612,female Header, 2-way, Molex Minifit Jr Header, 2-way, Molex KK Provision for M3 ring terminal THEORY OF OPERATION Figure 2-3 is a circuit diagram showing a typical digital input channel. Power supplies for the termination cards are normally provided by a Power Distribution Panel PDD24 which performs diode auctioneering of its dual redundant power supplies. Power for the digital input circuits (normally from the PDD24) is fed to input FS1 or FS2. Where the PDD24 is not used and dual supplies are required, these are connected to FS1 and FS2 respectively and auctioneered on the termination card by D17 and D18. Each digital input channel is powered via an indicating fuse from a common +ve bus. The fuse failed output from each fuse is connected to a common alarm bus. If any fuse fails, local indication is provided by the illumination of Fuse blown LED LD1. A signal to operate a remote alarm is available at Alarm output PL1. NOTE The PDD24 has a Fuse blown alarm indicator with provision for multiple inputs. This facility can be wired to provide fuse blown indication for an entire cabinet. The -ve bus may be grounded via TS1 if required, preventing the power supplies from floating when the chassis cable is disconnected. TDI16AIA October 2005 Issue 3 7
8 TRANSIENT SUPPRESSION A transient suppressor is fitted across each digital input channel input to the SC300E chassis. It provides a discharge path for transient energy pulses that may appear on the digital input line following lightning strikes etc. The suppressor is effectively a zener diode with a breakdown voltage just above that of the normal supply voltage. In normal operation, therefore, the suppressor does not conduct (apart from leakage current). In the presence of a transient pulse, zener breakdown occurs. The voltage developed across the suppressor varies to some extent with the pulse current and is known as the clamping voltage. The following characteristics are typical: Table 2-1. Transient suppressor characteristics Clamping Voltage Pulse currents Pulse duration Comments +37V to +43V *1mA Continuous *Maximum current continuous overload +70V **6gAmps 8 to 20 υs **Maximum peak pulse current SUPPLEMENTARY INFORMATION Table 2-2 lists the digital input channel wiring connections and associated fuses for connectors J1 and J2. Pin J1-1a is connected to the +ve bus (Figure 2-3 ). Pins J1-1c and J2-1c are interconnected. J1/J2 pins other than J1-1a, J1-1c, J2-1c and those listed in Table 2-2 are not connected. 8 TAI16AIA October 2005 Issue 3
9 TDI16AIA 16-Channel D/I Termination Card 24Vdc Table 2-2. Digital input channel connections Screw terminals DIN41612 Connector J1 Channel Field loop input signal Field loop return from field device Field loop fused (+ve) input to chassis Field loop fused input return (-ve) Fuse 1 1(+) 1(-) J1-2a J1-2c F1 2 2(+) 2(-) J1-4a J1-4c F2 3 3(+) 3(-) J1-6a J1-6c F3 4 4(+) 4(-) J1-8a J1-8c F4 5 5(+) 5(-) J1-10a J1-10c F5 6 6(+) 6(-) J1-12a J1-12c F6 7 7(+) 7(-) J1-14a J1-14c F7 8 8(+) 8(-) J1-16a J1-16c F8 g g(+) g(-) J1-18a J1-18c Fg 10 10(+) 10(-) J1-20a J1-20c F (+) 11(-) J1-22a J1-22c F (+) 12(-) J1-24a J1-24c F (+) 13(-) J1-26a J1-26c F (+) 14(-) J1-28a J1-28c F (+) 15(-) J1-30a J1-30c F (+) 16(-) J1-32a J1-32c F16 TDI16AIA October 2005 Issue 3 g
10 SERVICING SCOPE The TDI16AIA contains all-passive circuitry that is extremely robust. Servicing operations will therefore not normally extend beyond the replacement of failed fuses. CAUTION Before replacing a failed fuse, ascertain the cause of failure, and take the appropriate remedial action. CONFIGURATION No configurable links. 10 TAI16AIA October 2005 Issue 3
11 TDI16AIA 16-Channel D/I Termination Card 24Vdc SERVICE SUPPORT SPARE PARTS Spare parts and technical advice can be obtained from your local area offices. LIST OF SPARES Circuit Ref Part No Details F1 to F A Indicating fuse TAI16AIA October 2005 Issue 3
16-Channel Digital Input Termination Card 24Vdc
TDI16BIA 16-Channel Digital Input Termination Card 24Vdc (TDI16BIA) Issue 3 October 2005 INTRODUCTION PURPOSE The TDI16BIA16-channel digital input termination card acts as an interface between the digital
More information16-Channel Input Digital Input Termination Card
TDI16EIA 16-Channel Input Digital Input Termination Card (TDI16EIA) Issue 3 October 2005 Introduction Purpose The TDI16EIA 16-channel digital input termination card acts as an interface between the digital
More informationChassis Power Supplies
PDC24 / PAC Chassis Power Supplies (PDC24 / PAC) Issue 3 October 2005 INTRODUCTION PURPOSE Two Power Supply Units (PSUs) provide a dual-redundant source of 5.4Vand 12Vdc onto the backplane for the modules
More information32-Channel Analogue Input Module Differential Input
MAI32*AD 32-Channel Analogue Input Module Differential Input (MAI32*AD) Issue 4 October 2005 INTRODUCTION PURPOSE The Analogue Input Module provides up to 32, low voltage or current analogue input signals.
More informationRemote Bus Extender Slave Module
Triguard SC300E MRB01XS Remote Bus Extender Slave Module (MRB01XS) Issue 4 October 2005 INTRODUCTION AND TECHNICAL DATA PURPOSE A Remote Bus Extender Slave Module MRB01XS (Figure 1-1 ) is located in each
More information16-Channel Digital Output Module 120Vac/dc
Triguard SC300E MDO16FNS 16-Channel Digital Output Module 120Vac/dc (MDO16FNS) Issue 4 October 2005 INTRODUCTION PURPOSE The 120Vac/dc Digital Output Module MDO16FNS provides the output control interface
More informationDe-multiplexed Display Driver. Revision 02. User Manual. TM117-DMX Motherboard Daughterboard
Triguard SC300E TM117-DMX 64 Channel De-multiplexed Display Driver Revision 02 008-5216-02 User Manual This manual covers the following items: Model Ref Part No for standard item. TM117-DMX -------------
More informationI/O Expansion Module Installation & Reference
Overview The In-Sight vision sensor supports up to ten discrete inputs and ten discrete outputs. Two inputs and two outputs are built-in to the In-Sight processor. The remaining eight inputs and outputs
More informationOperating Instructions
Introduction To protect the signal lines of field devices and systems in the cabinet against lightning. Pepperl+Fuchs covers the complete range of Surge Protection Barriers. Housing types Depending on
More informationAllen-Bradley PLCs. 100 Programmable Controller Processor Unit -Catalog Nos LPI01, -LP102, -LP103, -LP104 SLC TM. The Unit
PRODUCT DATA SLC TM 100 Programmable Controller Processor Unit -Catalog Nos. 1745-LPI01, -LP102, -LP103, -LP104 The SLC 100 programmab/e Contro"er The SLC 100 Programmable Controller is easy to program,
More informationAOZ8900. Ultra-Low Capacitance TVS Diode Array PRELIMINARY. Features. General Description. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The is a transient voltage suppressor array designed to protect high speed data lines from Electro Static Discharge (ESD) and lightning. This device
More informationTMP & TMPM Series, 4 to 60 Watt. Order code Output power max. Output Efficiency
TMP & TMPM Series, 4 to 60 Watt Features Ultra compact, low profile plastic casing Fully encapsulated (pollution/dust) Single-, dual- and triple output models standard package versions: - Screw terminal
More informationTM3AI4 module TM3-4 analog inputs
Characteristics module TM3-4 analog inputs Main Range of product Product or component type Range compatibility Analogue input number 4 Analogue input type Complementary Analogue input resolution Permissible
More informationABL8BBU24200 battery control module V DC - 24 V - 20 A - for regulated SMPS
Characteristics battery control module - 24..28.8 V DC - 24 V - 20 A - for regulated SMPS Main Range of product Product or component type Input voltage Output voltage Maximum output current Phaseo Battery
More informationSeries AME5-CJZ 5 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: I/O Isolation 000V Continuous Short circuit protection Operating Temp: -2 C to 0 C Energy Star compliant Input: -26V, -6Hz, or 20-0VDC pact
More informationABL8BBU24400 battery control module V DC - 24 V - 40 A - for regulated SMPS
Characteristics battery control module - 24..28.8 V DC - 24 V - 40 A - for regulated SMPS Main Range of product Product or component type Input voltage Output voltage Maximum output current Complementary
More informationINSTRUCTION SHEET. Eaton Logic Controller ELCB Controllers
2010-12-10 5011699201-PBB1 Eaton Logic Controller ELCB Controllers INSTRUCTION SHEET [Applicable Controllers] ELCB-PB10 ELCB-PB14 ELCB-PB20 ELCB-PB30 ELCB-PB40 IL05001005E 002-1310020-02 Thank you for
More informationABL8REM24050 regulated SMPS - 1 or 2-phase V AC - 24 V - 5 A
Characteristics regulated SMPS - 1 or 2-phase - 100..240 V AC - 24 V - 5 A Main Range of product Product or component type Power supply type Input voltage Output voltage Rated power in W Input protection
More informationMicro Contactor MA Series
Relay-sized contactor, making it the world s smallest >3mm contact clearance acc. to IEC 60335-1 for Safety Applications Reversing contactor with mechanical interlock 3 Pole and 1 Aux. Contact NO or NC
More informationZener Barriers Bulletin 937Z
Technical Data Zener Barriers Bulletin 937Z Topic Page Introduction 2 Mounting 2 Housing 3 Operating Principle 3 Specifications 6 Introduction Allen-Bradley Zener barriers are a cost-effective solution
More informationTime Counters mini "h", DC Version
Type 633-DC Time Counters mini "h", DC Version Type 633.0 Type 633.7 Type 633.8 High shock resistance Miniature dimensions Electrical connections in standard grid Suitable for PCB mounting Machine-solderable
More informationIndustrial Power Supplies
75-600 Watt Features Switch mode power supplies for DIN-rail mounting 4 power ranges with 3, 6, 12 and 24 A output current (24 VDC models) Selectable 115/ 230 VAC input Very low ripple and noise EMI complies
More informationMODULES FOR SAFETY AND MONITORING
MODULES FOR SAFETY AND MONITORING Woertz AG Hofackerstrasse 47, P.O. Box 948, CH-43 Muttenz, Switzerland Tel. ++4 6 / 466 33 33, Fax ++4 6 / 46 96 06 http://www.woertz.ch Woertz-USA 5 Discovery Drive,
More informationSurge Protection Devices Ex9UE2
Surge Protection Devices Ex9UE2 Surge Protection Devices Type 2 (Class II, T2, C) Tested according to EN 61643-11 Maximum continuous operational voltage U c from 275 V up to 440 V AC Versions with 1+0,
More informationTM3TI4 module TM3-4 inputs temperature
Characteristics module TM3-4 inputs temperature Main Range of product Product or component type Range compatibility Analogue input number 4 Analogue input type Complementary Analogue input resolution Permissible
More informationIndustrial Power Supplies
50-600 Watt Features Switch mode power supplies for DIN-rail mounting 6 power ranges with 2, 3, 6, 12, 20 and 24 A output current (24 VDC models) Selectable 115/ 230 VAC input Very low ripple and noise
More informationSPM Series Plug-in Surge Protector Type 2/3 (Test Class II/III) Single & Three Phase Surge Arresters
The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects of transient over voltages caused by
More informationABL8REM24050 regulated SMPS - 1 or 2-phase V AC - 24 V - 5 A
Characteristics regulated SMPS - 1 or 2-phase - 100..240 V AC - 24 V - 5 A Complementary Input voltage limits Network frequency Inrush current Main Range of product Product or component type Power supply
More informationVital. Safety controller. Approvals: Control of: Features: Entire safety system based on the dynamic safety circuit.
Safety controller Vital Approvals: TÜV Nord Vital 1 TÜV Rheinland Vital and 3 Control of: Entire safety system based on the dynamic safety circuit. Features: Vital is based on a single channel safety concept
More informationAOZ8101. Ultra-Low Capacitance TVS Diode Array. General Description. Features. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The AOZ8101 is a transient voltage suppressor array designed to protect high speed data lines from Electro Static Discharge (ESD) and lightning.
More informationdigiclip Data sheet DF31CAN Special features B en
digiclip DF31CAN Data sheet Special features Digital amplifier for industrial automation tasks and production process monitoring 600 Hz CF measurement technology with TEDS sensor detection for SG full
More informationSeries AME25-JZ 25 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Series AME-JZ I/O Isolation 000VAC Low Ripple and Noise Operating Temp: -0 C to +70 C Over Voltage Protection Over current Protection Up to
More informationI R T Electronics Pty Ltd A.B.N. 35 000 83 575 6 Hotham Parade, ARTARMON N.S.W. 064 AUSTRALIA National: Phone: (0) 9439 3744 Fax: (0) 9439 7439 International: +6 9439 3744 +6 9439 7439 Email: sales@irtelectronics.com
More informationINPAQ Global RF/Component Solutions
TVL SC7 4 AC Specification Product Name Series Part No Package Size Transient Voltage Suppressor TVS Series TVL SC7 4 AC SC7-6L TVL SC7 4 AC Engineering Specification 1. Scope TVL SC7 4 AC s are TVS arrays
More informationMINI-PS AC/10-15DC/8
Primary-Switched Power Supply, Narrow Design Data Sheet 08/2004 MINI POWER provides: An extra narrow design, with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a
More informationNMEA Expander. Operation And. Installation Manual
NMEA Expander Operation And Installation Manual XXXXXX_20130331 Revision B0 Syberg Maritim 1. OPERATION AND CONFIGURATION... 3 SYSTEM SUMMARY... 3 INPUT POWER SUPPLY, D CONFIGURATION... 4 INPUT POWER SUPPLY,
More informationPHOENIX CONTACT - 07/2006
Buffer module with maintenance-free capacitor-based power storage device INTERFACE Data sheet 102035_03_en PHOENIX CONTACT - 07/2006 Description Short-term mains interruptions are bridged by QUINT BUFFER,
More informationXPSMCMDO Digital output pairs expansion modules with screw term
Characteristics 2 Digital output pairs expansion modules with screw term Main Range of product Product or component type Device short name Electrical connection [Us] rated supply voltage Number of inputs
More informationTM3TI8T module TM3-8 inputs temperature
Characteristics module TM3-8 inputs temperature Main Range of product Product or component type Range compatibility Analogue input number 8 Analogue input type Complementary Analogue input resolution Input
More informationNMID. Remote control. SAPIM I/O number. SAPIM I/O number NBRN (RS485) ZM100. Relay, 24 VDC - + UO07 UI11 UI10 UI09 UI08 UI07 UI06 UI05 UI04 UI03 UI02
1/8 NRK16/A, NRK16-B/A, (NRK16-T /A, NRK14-T /A, NRK16-WEB/A) Control and interlock devices with pre-programmed system-specific application modules The controllers may be used as stand-alone control and
More informationXPSMCMDI Input expansion module with screw term
Characteristics 16 Input expansion module with screw term Main Range of product Product or component type Device short name Electrical connection [Us] rated supply voltage Number of inputs Number of outputs
More informationCliQ II DC-UPS Module 24V 40A / DRU-24V40ABN
Highlights & Features Full corrosion resistant Aluminium chassis Suitable for 24V system up to 40A Built-in diagnostic monitoring for DC OK, Discharge and Battery Fail by relay contacts LED indicator for
More informationTM3TM3 module TM3-2 temperature inputs and 1 analog output
Characteristics module TM3-2 temperature inputs and 1 analog output Main Range of product Product or component type Range compatibility Analogue input number 2 Analogue input type Analogue output number
More informationAOZ8102. Ultra-Low Capacitance TVS Diode Array. Features. General Description. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The is a transient voltage suppressor array designed to protect high speed data lines from SD and lightning. This device incorporates eight surge
More informationdigiclip Data sheet DF31DP Special features B en
digiclip DF31DP Data sheet Special features Digital amplifier for industrial automation tasks and production process monitoring 600 Hz CF measurement technology with TEDS sensor detection for SG full bridges
More informationOTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m
Characteristics I/O distributed module OTB - Ethernet TCP/IP - 0..100 m Main Range of product Product or component type Integrated connection type Mar 31, 2018 Modicon OTB I/O distributed module Discrete
More informationABL8RPS24100 regulated SMPS - 1 or 2-phase V - 24 V - 10 A
Characteristics regulated SMPS - 1 or 2-phase - 100..500 V - 24 V - 10 A Main Range of product Product or component type Power supply type Input voltage Output voltage Rated power in W Jun 27, 2018 Phaseo
More informationKEPCO GIVES YOU ZERO-UP PROGRAMMABILITY IN AN AFFORDABLE POWER MODULE
146-1915 More than switch mode boxes with wide-range a-c/d-c input power factor correction and current-share capacity... KEPCO GIVES YOU ZERO-UP PROGRAMMABILITY IN AN AFFORDABLE POWER MODULE RKW 300W 92
More informationABL8REM24030 regulated SMPS - 1 or 2-phase V AC - 24 V - 3 A
Characteristics regulated SMPS - 1 or 2-phase - 100..240 V AC - 24 V - 3 A Product availability : Stock - Normally stocked in distribution facility Price* : 195.00 USD Main Range of product Product or
More informationINPAQ. Specification TVN AB0. Product Name Transient Voltage Suppressor Series TVS Series Part No TVN AB0 Size EIA 0201
TVN 0201 01 AB0 Specification Product Name Transient Voltage Suppressor Series TVS Series Part No TVN 020101 AB0 Size EIA 0201 TVN 0201 01 AB0 Engineering Specification 1. Scope TVN 0201 01 AB0 is a TVS
More informationF101, F102, F104. Relcom Installation Instructions. Fieldbus Power Supply F101-PS
F101, F102, F104 Fieldbus Power Supply F101-PS Installation Instructions Relcom www.mtl-fieldbus.com CONTENTS PAGE 1 OVERVIEW 2 2 DESCRIPTION 2 3 COMPONENTS AND ACCESSORIES 2 4 MECHANICAL 3 4.1 Mounting
More information1, 2, 4 and 8-Channel Very Low Capacitance ESD Protectors
1, 2, 4 and 8-Channel Very Low Capacitance ESD Protectors CM1210 Features 1,2,4 and 8 channels of ESD protection Very low loading capacitance (1.0pF typical) ±6 kv ESD protection per channel (IEC 61000-4-2
More informationTM3TI4 module TM3-4 inputs temperature
Characteristics module TM3-4 inputs temperature Complementary Analogue input resolution Permissible continuous overload Input impedance LSB value Conversion time Sampling duration Main Range of product
More informationSafety Standards. Model Number: Unit Weight:
MEA-250A24C Highlights & Features Meet Efficiency Level VI Safety Approvals to IEC 60601-1 3.1 Ed. & IEC 60950-1 Compliant with IEC 60601-1-2 3 th and 4 th Ed. Requirements IP22 ingress protection rating
More informationABL8WPS24400 regulated SMPS - 3-phase V - 24 V - 40 A
Characteristics regulated SMPS - 3-phase - 380..500 V - 24 V - 40 A Main Range of product Product or component type Power supply type Input voltage Output voltage Rated power in W Jan 11, 2018 Phaseo Power
More informationMPU-120S Series. Single Output, 180W Compact, U-Channel AC/DC Power Supplies. Key Features:
MPU-120S Series Single, 180W Compact, U-Channel AC/DC Power Supplies Key Features: 180W Power Universal 90-264 AC Power Factor Correction EN 60950 Approved Compact U-Channel Five Single Models Meets EN
More informationABL8RPS24100 regulated SMPS - 1 or 2-phase V - 24 V - 10 A
Product datasheet Characteristics ABL8RPS24100 regulated SMPS - 1 or 2-phase - 100..500 V - 24 V - 10 A Complementary Input voltage limits Network frequency Inrush current Cos phi Main Range of product
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 59,5mm Suitable for mounting in domestic installation panels Low output ripples and spikes Fully compliance to ECO-Standard
More informationOTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m
Product datasheet Characteristics OTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP - 0..100 m Complementary Concept Port Ethernet Bus length Main Number of devices per segment 0...256 Communication
More informationTrusted 40 Channel Digital Input Versatile FTA
PD-T8843 Trusted Trusted 40 Channel Digital Input Versatile FTA Product Overview The Trusted 40 Channel Digital Input Versatile Field Termination Assembly (VFTA) T8843 is designed to act as the main interface
More informationSPM Series Plug-in Surge Protection
SPM Series Plug-in Surge Protection The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 55 mm Suitable for mounting in domestic installation panels Very high efficiency and low standby power -> compliance to
More informationXPSMCMMX inputs 2 output pairs expansion module with screw term
Characteristics 8 inputs 2 output pairs expansion module with screw term Main Range of product Product or component type Device short name Electrical connection [Us] rated supply voltage Number of inputs
More informationAOZ8882. Ultra-Low Capacitance TVS Diode Array. General Description. Features. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The AOZ8882 is a transient voltage suppressor array designed to protect high speed data lines such as HDMI, MDDI, USB, SATA, and Gigabit Ethernet
More informationCONTROL MICROSYSTEMS Analog Input Module. Hardware Manual
550 Analog Input Hardware Manual CONTROL MICROSYSTEMS SCADA products... for the distance Steacie Drive Telephone: 63-59-93 Kanata, Ontario Facsimile: 63-59-0 KK A9 Technical Support: -6-676 Canada -CONTROL
More informationRedundancy unit CP-A RU
2CDC 271 010 F0t06 Features Decoupling of CP power supply units with 2 inputs, each up to 20 A per input / channel Output up to 40 A True redundancy by 100 % decoupling of two parallel connected power
More informationENGINEERING SPECIFICATION SHEET SPEC. Revision History
SPEC. Revision History Revision Change Information Date No. Description Current version 2010/08/01 1 New revision Initial 2011-1-25 2 Fuse is changed T4.0A 2.0 2011-4-1 3 Add AC adapter external dimension
More informationChrome DIN Rail Power Supply 5V 7.5W 1 Phase (Class II & NEC Class 2) / DRC-5V10W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More information8B0C0320HW General information. 2 Order data. 3 Technical data 8B0C0320HW
1 General information Connections for supplying external 24 V devices Extensive protective measures 2 Order data Model number Short description Figure Wall mounting ACOPOSmulti auxiliary supply module,
More informationXPSMCMCO0000EM Modbus TCPIP diagnostic expansion module with screw term
Characteristics Modbus TCPIP diagnostic expansion module with screw term Main Range of product Product or component type Device short name [Us] rated supply voltage Complementary Power dissipation in W
More informationExpansion Unit Catalog Nos , - 152, - 153, - 154, - 156, -E157
PRODUCT DA TA SLC 150 110 Expansion Unit Catalog Nos. 1745-151, - 152, - 153, - 154, - 156, -E157 7 : The EXpdnSiQn Unit The SLC 150 expansion unit can be used with either the SLC 150 processor unit or
More informationClick Desktop Kit. Click Desktop Kit
Click Desktop Kit Click Desktop Kit The Click Desktop Kit is a desktop-mounted set that gives you the building blocks necessary to work with your Click modules at your computer, whether you re testing
More informationPDD-300 pulsed diode driver
rev 1.08 / 2019 02 13 PDD-300 pulsed diode driver User manual Warning! This equipment may be dangerous. Please read user manual before starting operations. Important note. Please measure output with adequate
More informationXPSMF40. Main. Safety module name. Monitoring safety detection discrete input Monitoring safety dialogue discrete output
Product datasheet Characteristics XPSMF4000 Preventa safety PLC compact - Safe Ethernet Main Range of product Product or component type Safety module name Safety module application Preventa Safety automation
More informationCliQ II Buffer Module 24V 20A / DRB-24V020AB
Highlights & Features Full corrosion resistant Aluminium chassis Long minimum buffering time of 250ms @ 24V/20A Can connect in parallel to increase buffering time Charging time of < 30 seconds Conformal
More informationDALI Bus Power Supply. DLP- 04 series VAC
0 05 VAC Ⅱ,. { File Name: DLP-0-SPEC 08-08-6 SPECIFICATION MODEL DLP-0R DLP-0L OUTPUT RATED POWER SETUP, RISE TIME HOLD UP TIME (Typ.) 70ms/0VAC 6ms/5VAC at full load VOLTAGE RANGE 90 ~ 6VAC 0 ~ 70VDC
More informationRhino PSM Power Supplies. Operating Instructions
Rhino PSM Power Supplies Operating Instructions RHINO Power Supplies PSM Series Description The PSM power supplies are built-in units. The mounting position for PSM power supplies must fulfill the requirements
More informationNI REM Remote I/O Overview DATASHEET. Digital Output Module for Remote I/O
DATASHEET NI REM-11178 Digital Output Module for Remote I/O Short circuit and overload protection Drives up to 500 ma per channel (up to 8A per module) Spring-terminal connectors allow fast wiring without
More informationExpansion Module HZS 541-1S
Expansion Module HZS 541-1S 12.10.2015 Page 1 System Description The external HZS 541-1S expansion module provides users of biomass heating systems with additional 230 V AC relay outputs, analog inputs
More informationOTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m
Characteristics I/O distributed module OTB - Ethernet TCP/IP - 0..100 m Complementary Concept Port Ethernet Bus length Main Number of devices per segment 0...256 Communication service Web services Discrete
More informationMTII4200 Level Transmitter Installation, Operation & Maintenance Instructions
Specialists in Liquid Level Indication MTII4200 Level Transmitter Installation, Operation & Maintenance Instructions Section: M500 Bulletin: M500.31 Date: 05-17-16 Supersedes: 09-30-11 1. INTRODUCTION
More informationEngineering Guideline. pac-carriers Type for Honeywell system Experion Series C I/O
Engineering Guideline pac-carriers Type 995 for Honeywell system Experion Series C I/O pac-carrier Type 995 Engineering Guideline/Honeywell 04..009 pac-carrier Type 995 Integration of conventional process
More informationABL8RPS24030 regulated SMPS - 1 or 2-phase V - 24 V - 3 A
Characteristics regulated SMPS - 1 or 2-phase - 100..500 V - 24 V - 3 A Product availability : Stock - Normally stocked in distribution facility Price* : 270.00 USD Main Range of product Product or component
More informationSPM Series. Plug-in Surge Protection
SPM Series Plug-in Surge Protection The SPM series of modular surge protection devices provides protection of equipment connected to incoming low voltage AC power supplies against the damaging effects
More informationSeries AMEL10-MJZ 10 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com Models Single output Model Input Voltage (VAC/Hz) FEATURES: Input Voltage (VDC) Max Output wattage (W) Output Voltage (V) Output Current max (A) Maximum
More informationMAINTENANCE MANUAL. EDACS REDUNDANT POWER SUPPLY SYSTEM 350A1441P1 and P2 POWER MODULE CHASSIS 350A1441P3, P4, AND P5 POWER MODULES TABLE OF CONTENTS
MAINTENANCE MANUAL EDACS REDUNDANT POWER SUPPLY SYSTEM 350A1441P1 and P2 POWER MODULE CHASSIS 350A1441P3, P4, AND P5 POWER MODULES TABLE OF CONTENTS SPECIFICATIONS*... 2 INTRODUCTION... 3 DESCRIPTION...
More informationInstallation Instructions
Installation Instructions (Catalog Number 1771-OD) This document provides information on: Because of the variety of uses for the products described in this publication, those responsible for the application
More informationCONTROL MICROSYSTEMS and 5407 Relay Output Module. Hardware Manual
506 and 507 Relay Output Module Hardware Manual CONTROL MICROSYSTEMS SCADA products... for the distance Steacie Drive Telephone: 63-59-93 Kanata, Ontario Facsimile: 63-59-0 KK A9 Technical Support: -6-676
More informationAOZ8234. Four-line TVS Diode
AOZ8 Four-line TS Diode General Description The AOZ8 is a transient voltage suppressor diode array designed to protect data lines from high transient conditions and ESD. This state-of-the-art device utilizes
More informationVL BPC MINI. A configurable industrial computer platform. Data sheet 2930_en_F. 1 Description. 2 Features
A configurable industrial computer platform Data sheet 90_en_F Description PHOENIX CONTACT 0-08- Features The VL BPC MINI is an embedded box PC and is part of the Valueline family of industrial computers.
More informationSeries AMES40-MAZ 40 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model (VAC/Hz) (VDC) Output Voltage (V) Output Current max (A) Efficiency (%) AMES40-3.3SMAZ 90-264/47-440 130-370 3.3
More informationABL1REM24025 regulated SMPS - single phase V input - 24 V output - 60 W
Characteristics regulated SMPS - single phase - 100..240 V input - 24 V output - 60 W Main Range of product Product or component type Power supply type Rated power in W Input voltage Output voltage Power
More informationOvervoltage Protection Devices
Siemens AG 2010 Overvoltage Protection Devices /2 Introduction /3 Lightning Arresters, Type 1 /5 Combination Surge Arresters, Type 1 and Type 2 /7 Surge Arresters, Type 2 /11 Surge Arresters, Type 3 /12
More informationSeries AME10-VZ 10 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: Picture Coming Soon I/O Isolation 000VAC Continuous Short circuit protection Operating Temp: -0 C to + C Energy Star compliant Input: -VAC,
More informationABL8WPS24200 regulated SMPS - 3-phase V AC - 24 V - 20 A
Characteristics regulated SMPS - 3-phase - 380..500 V AC - 24 V - 20 A Product availability : Stock - Normally stocked in distribution facility Price* : 735.00 USD Main Range of product Product or component
More informationSITOP in the SIMATIC Design
Siemens AG 2017 /2 Introduction /3 1-phase, 24 V DC (for S7-300 and ET 200M) /9 1-phase, 24 V DC (for S7-1200) /11 1-phase, 24 V DC (for S7-1500 and ET 200MP) /14 3-phase, 24 V DC (ET 200pro) Siemens KT
More informationIB ST 24 AO 4/EF. INTERBUS-ST analog output module, 4 outputs, 0-10 V, ±10 V, 0-20 ma, 4-20 ma. Data sheet. 1 Description
INTERBUS-ST analog output module, 4 outputs, 0-10 V, ±10 V, 0-20 ma, 4-20 ma Data sheet 105597_en_01 PHOENIX CONTACT 2014-10-24 1 Description The module is designed for use within an ST station. It is
More informationSubmittal Data Sheet WAGO Node for itm
The WAGO Node integrates ancillary equipment into the Intelligent Touch Manager (itm) DCM601A71 with the use of DI, DO, AI and AO signals. It provides monitoring and control of non-daikin equipment via
More informationCPT-COM-U Card. TTL Serial USB Isolated Interface Board. Technical Brief
CPT-COM-U Card TTL Serial USB Isolated Interface Board Technical Brief June 2014 Manual Release 1.0 Card Version 1.1 Copyright 2014 Creative Power Technologies P/L P.O. Box 714 MULGRAVE Victoria, 3170
More informationABL1RPM24100 regulated SMPS - single phase V input - 24 V output W
Characteristics regulated SMPS - single phase - 100..240 V input - 24 V output - 240 W Complementary Input voltage limits Network frequency limits Inrush current Main Range of product Product or component
More information