GSDR Basic set up using QRP2000. Modes using third party software will be covered in another tutorial. Remember you must download two files, the
|
|
- Marjory Lawson
- 6 years ago
- Views:
Transcription
1 GSDR Basic set up using QRP2000. Modes using third party software will be covered in another tutorial. Remember you must download two files, the install and the latest update. Extract both folders and copy all the files from the update to the install folder. Allow files to be over written! GSDR doesn't actually install on your computer, it is self contained in each folder. You can have as many instances of the program you want. A tip when you update in the future. Copy the current program folder to a back up folder and then apply the update. If for some reason the update has bugs you can easily go back to the older version.
2 GSDR has built in QRP2000 support. The PTT control is through QRP2000 using a jumper to the Avala01 which is covered in another PDF. The first thing I do is to calibrate the SI570. GSDR now supports Si570 calibration with the QRP2000. In the QRP2000 box press the GET button and the boxes should populate. The VID and PID are read only but the Si570 Address (I2C) is changeable. The flow I use is to press GET and then APPLY to save the configuration. If for some reason you go to far with the Si570 Xtal numbers you can always select CANCEL and be back to where you started. To adjust the frequency just press the up or down arrows till the frequency is centered. You need to press SET to check your progress. When done press SAVE. See the next slide.
3
4 The signal is 7.020mhz. Zoomed in you can see it needs adjustment
5 Now you can see each time I changed the numbers and pressed SET till is was right on center. The last adjustment may require you manually enter a number between the steps the arrow buttons gives.
6 Next using a signal source calibrate LEVEL. Just input the frequency and level of the signal and select START. RX image adjustment is covered in another tutorial.
7 Next is sound card setup. Pretty straight forward. If you get popping or intermittent audio then change buffer and sample rate. Some cards require IQ correction to work correctly. You also need to find your max output voltage for your sound card. Set your DVM to AC scale and connect to audio out cable from sound card, Tip and Shield. When you press test record the voltage and enter it in the block.
8 VAC(Virtual Audio Cable) This is the audio link to communicate with other programs like WSPR, JT65HF, Fldigi and others. The virtual cable are setup by another program. See next slide
9 VAC(Virtual Audio Cable) Each virtual cable connects the different software to GSDR or other SDR program. The full version much be purchased at: I have heard of folks successfully using the free version but the pay version is recommended. You need two cables to make connection. GSDR input from another program on Virtual Cable 1 and output to the other program on Virtual Cable 2. On the third part software it will be set up just the opposite Input VC2 and Output VC1
10 This is where TX image adjustment is accomplished. Need to be completed for each band of operation and click CALIBRATE BAND each time. The process is covered in another PDF.
11 This is the Transmit Tab. Things to note are the TUNE Power setting. When pressing tune it will go to this setting. Can be manually adjusted on the main radio controls page. Also the TX IF shift. It is recommended that you use this setting so that TX image rejection is constant across band. When Image adjustment is done the TX Frequency is 10khz above the LO so I make my shift 10khz. GSDR will shift 10khz each time you transmit. The block is in hz so I use I forgot to change it before making slide.
12 PA Settings: This is used to set your maximum out put power. Before starting click reset and all bands will show 48.0 this is center or medium power. Then check each band you will use. With TUNE set to 100% adjust number values lower for higher power and number values higher for lower output power. This allows you to never exceed the max power of your PA with slider to 100%. 36 is max and 56 is minimum power settings. The ADC is used for Power meter calibration but other hardware is needed for functionality. DO NOT CLICK CALIBRATE WHEN DONE JUST CLICK SAVE AT BOTTOM!
13 Test page: Some useful tools here. One test that I have used is the signal generator. You can select tone and output and with head phones plug into the Avala01 you can check left and right audio. There are several different type of wave patterns for troubleshooting.
14 Cat Control Page: This is where you set GSDR control from third party software. You need to install a program that links com ports that you will use at each end. See the next slide.
15 This is the program I use. You need to link com ports so each end is a different number but linked. Otherwise you would get com port conflicts. For example lets say we want JT65HF to control PTT on the Avala01. We could use pair 7 and 17. One end, COM 7, would be used on the GSDR PTT and the other end, COM17, would be used in the JT65HF program. So when the PTT signal is sent through COM17 it will end up at COM7 to activate PTT in GSDR.
PowerSDR with Pi SDR for G59/G11 Software Setup
PowerSDR with Pi SDR for G59/G11 Software Setup Software installation is performed with a provided unified installer containing both the PowerSDR v2.5.3 and Pi SDR Extensions v4.6.8. The PowerSDR for Pi
More informationW0EB/W2CTX Firmware for the Micro BITX meter Transceiver for Release V2.00R
W0EB/W2CTX Firmware for the Micro BITX 80-10 meter Transceiver for Release V2.00R Software running on W0EB s Test Platform. Version 2.00b is final pre-release test. Instructions for ubitx Version 2.00R
More informationDM780 / Navigator Setup
When you first start with HRD / DM780, you need to define a few Navigator parameters to the program so it can communicate with your radio through the Navigator. The items that need to be defined are: DM780:
More informationHT-1A Dual Band CW QRP Transceiver. User Manual
HT-1A Dual Band CW QRP Transceiver User Manual Rev A, June 17, 2018 Designed by BD4RG Exclusively distributed by CRKITS.COM and its worldwide distributors Join the group http://groups.io/g/crkits to get
More informationUser Manual for KD8CEC ubitx firmware rev 1.072
Table of Contents Introduction...3 Acknowledgments...4 New Features...5 Four different types of LCD display are supported...5 Optional Factory Calibration...5 SDR Support...5 S Meter support...6 Support
More informationBASIC Arduino. Part I
BASIC Arduino Part I Objectives Introduction to Arduino Build a 1-60MHz DDS VFO prototype, breadboard and write Sketches, with Buffer amps to be designed, and PCB Using your own laptop Go on to build other
More informationUser Manual for KD8CEC ubitx software rev 1.061
Table of Contents Introduction...3 Software Installation...5 Installing a.hex file...5 Installing from source files...5 Initial display...8 CECSW Menu system...9 MAIN MENU...10 Band Select...11 Select
More informationAFEDRI SDR-USB-HS short user manual.
AFEDRI SDR-USB-HS short user manual. 1. AFEDRI SDR-USB-HS main information. The image of AFEDRI SDR-USB-HS receiver, it contains also the external connectors and indication LEDs that are marked on the
More informationManual d'instruccions MixW
Manual d'instruccions MixW Table of Contents Last update - 20 July 2002. 1. I have gray space under tool bars is too large. 2. How can I set MixW for slow computers? 3. Waterfall seems to move to slow?
More informationPenelope Operation with PowerSDR
High Performance Software Defined Radio Open Source Hardware and Software Project Project Description: http://hpsdr.org Penelope Operation with PowerSDR Text: Phil Harman, VK6APH Joe de Groot, AB1DO Revision
More informationInside the Ten-Tec 506 Rebel Open Source QRP CW Transceiver. Bob Proctor, N6YPE and Brian Tompson, AC7FK
Inside the Ten-Tec 506 Rebel Open Source QRP CW Transceiver Bob Proctor, N6YPE and Brian Tompson, AC7FK About us Bob, N6YPE, has been licensed since 1990, is now an applications engineer at Microchip.
More informationUser Manual for KD8CEC ubitx firmware rev 1.061
Table of Contents Introduction...3 Acknowledgments...4 Software Installation...5 Installing a.hex file...5 Installing from source files...5 Initial display...8 CECFW Menu system...9 MAIN MENU...10 Band
More informationHam Radio Deluxe - Troubleshooting ICOM Radio USB Port Data Modes.
Most of the new ICOM radio s include a USB sound codec device Driver information Firstly the radio control and audio may not function correctly if the rig was connected to the computer via the USB lead
More informationISOTERM-MULTICON USB
ISOTERM-MULTICON USB INSTRUCTIONS FOR CP-2102 Model DATA INTERFACE de G3LIV JULY 2012 Email Johnny@melvin.com Tel 0191-2843028 www.g3liv.co.uk 1 Welcome to the World of PSK-31. l want to make it easy for
More informationDIABLOSPORT PREDATOR REVISION UPDATE INSTRUCTIONS
DIABLOSPORT PREDATOR REVISION UPDATE INSTRUCTIONS This page contains instructions that will guide you through the process of updating the DiabloSport Predator to the latest software revision available.
More informationUser Guide: PFM 4000 Measuring Instrument - Multisource Version
User Guide: PFM 4000 Measuring Instrument - Multisource Version VUE2B102 Danfoss 11/2008 HEC Contents PFM main features... 5 Introduction... 5 PFM 4000 Multisource components... 6 Switching on and off...
More informationHow to use the IC-R8600 as an SDR receiver
How to use the IC-R8600 as an SDR receiver The IC-R8600 (version 1.30 or later) can output the In-phase/Quadrature data which is processed by the FPGA. Connect [I/Q OUT] to a PC s USB port, and you can
More information4M06 E&M Interface Module Guide
4M06 E&M Interface Module Guide This guide explains how to configure a 4M06 E&M Interface Module for use in a G-400 series communication system. After following this guide, you should be able to use an
More informationFor ICOM radio s Download the latest driver from ICOM Japan website they will always have the latest version
Driver information Firstly the radio control and audio may not function correctly if the rig was connected to the computer via the USB lead before the drivers were installed, so if you did this. Then go
More informationExclusive 2.5 GHz Frequency Counter
Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory
More informationSetting UP the UMI-1 with True RTA
Setting UP the UMI-1 with True RTA PC based test gear or single purpose device? Is there an easier way? Sure. There are lots of options for a single purpose device that will allow you to make frequency
More informationmicromax R Getting Started Guide
PN# 34-2114 Rev 1 04-25-2007 micromax R Introduction Introduction Thank you for purchasing Agile System s micromax R product. This guide covers how to install DPWin, connect, configure and tune a motor
More informationRelease Notes and Errata PowerSDR v2.3.5 Release
Release Notes and Errata PowerSDR v2.3.5 Release March 5, 2012 IMPORTANT: Read this document in its entirety before installing the new release of PowerSDR. PowerSDR v2.3.5 is an official general availability
More informationDigital Mode Demonstration using WSJT-X software
Digital Mode Demonstration using WSJT-X software Louis K4BYN & Tom N4TL April 10, 2018 Updated Sept 3, 2018 This presentation was given to the Raleigh Amateur Radio Society (RARS) Website addresses were
More informationExeter Amateur Radio Society
Exeter Amateur Radio Society Table of Contents Raynet Data Operations Guide Version 3-4 March 2012 Nick Johnson 2E0NRJ 1. PREPARATORY...2 1.1 Computer...2 1.1.1 Choice of hardware...2 1.1.2 Sound...2 1.1.3
More informationWaves API 560 User Manual
Waves API 560 User Manual TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...3 1.1 WELCOME...3 1.2 PRODUCT OVERVIEW...4 1.3 CONCEPTS AND TERMINOLOGY... ERROR! BOOKMARK NOT DEFINED. 1.4 COMPONENTS...5 CHAPTER 2
More informationJPSKmail quick start
JPSKmail 2.0.3 quick start Intro JPSKmail-2.0.3 is a self-contained program running on the java jvm. The java modems were taken from the fantastic fldigi program and translated from C++ to java by John,
More informationSierra Radio Systems. HamStack. Project Board Reference Manual V1.0
Sierra Radio Systems HamStack Project Board Reference Manual V1.0 Welcome HamStack Project Board Reference Manual Revision 1.0.3 2011 George Zafiropoulos, KJ6VU and John Best, KJ6K This guide provides
More informationSOUND LEVEL METER DVM1351 INSTRUCTION MANUAL HANDLEIDING MANUEL D UTILISATEUR DVM1351 SOUND LEVEL METER 1
SOUND LEVEL METER DVM1351 INSTRUCTION MANUAL HANDLEIDING MANUEL D UTILISATEUR DVM1351 SOUND LEVEL METER 1 SAFETY INFORMATION l Read the following safety information carefully before attempting to operate
More informationC-322. Model. Instruction Manual. Datalogging Sound Level Meter. reedinstruments. www. com. Tripod sold separately (Model BS-6)
Model C-322 Datalogging Sound Level Meter Instruction Manual Tripod sold separately (Model BS-6) reedinstruments com Table of Contents Features... 3 Specifications... 3 Instrument Description...4-5 Operating
More information1 Commissioning (basic settings and calibration)
Antenna Analyzer from EU1KY Software Variante DH1AKF 1 Commissioning (basic settings and calibration) Use Settings> Calibration> Oscillator Test (see 6.3.3) to determine the maximum frequency of the SI5351
More informationDMT80480T070-32WT User Guide
DMT80480T070-32WT User Guide Revision on April, 2014 Contents 1. Overview... 2 2. System Specifications... 2 3. Operating Guide... 4 3.1 Update the Boot Animation... 4 3.2 Hide / Show the Status Bar...
More informationGetting Started. With the Y-Lynx Starter Kit. Transce iver. of the XEMICS XE1205TrueRF tm. Y-Lynx web:
Getting Started With the Y-Lynx Starter Kit of the XEMICS XE1205TrueRF tm Transce iver Y-Lynx e-mail: info@y-lynx.com web: www.y.lynx.com Getting S tart ed with the Y-L ynx XE1 205TrueRF tm Start er Kit
More informationNew Computer Setup Guide Stenograph L.L.C
New Computer Setup Guide 2017 Stenograph L.L.C Table of Contents System Requirements... 2 Downloading Case CATalyst... 3 Using Internet Explorer or Microsoft Edge... 3 Using Mozilla Firefox... 6 Using
More informationYaesu FTDX3000 Sound card digital modes setup using internal USB interface for Fldigi (part 1)
Yaesu FTDX3000 Sound card digital modes setup using internal USB interface for Fldigi 3.23.13 (part 1) Getting the FTdx3000 and Fldigi just using the radios built in USB port. "YAESU FTDX3000 SOUND CARD
More informationHMH Leadership Form (Leader Guide)
b a a b c Overview: Leadership Evaluation Form Getting Started: On the Home Page, you ll see a To-Do tile for any modules that have pending tasks assigned to you. Either (a) Click on the hyperlink to navigate
More informationJUMA-TRX2 serial protocol description OH2NLT
JUMA-TRX2 serial protocol description OH2NLT 22.08.2007 JUMA-TRX2 serial interface protocol can be selected from TRX2 user setup. Long push of DISPLAY button gives setup menu for the user. Short pushes
More informationELAD Application Notes AN- 002 rev 1.0 Setting FDM- SW2 with external programs: CW Skimmer, FLDIGI
ELAD Application Notes AN- 002 rev 1.0 Setting FDM- SW2 with external programs: CW Skimmer, FLDIGI Table of contents: Introduction... 2 1 FDM- SW2 with CW Skimmer... 2 1.1 Requirements... 2 1.2 Software
More informationSoundance Bluetooth Speaker User Manual Model SDY019
Soundance Bluetooth Speaker User Manual Model SDY019 Thank you for purchasing Soundance Bluetooth speaker. Please read this manual carefully and keep it for future reference. Features of the speaker 1.
More informationFeatures. Warnings and Precautions READ BEFORE OPERATING EQUIPMENT SAVE THESE INSTRUCTIONS
SENTA Warnings and Precautions READ BEFORE OPERATING EQUIPMENT SAVE THESE INSTRUCTIONS To prevent damage to your radio or possible injury to you or others, read these safety precautions and instructions
More informationRIGblaster Plug & Play
RIGblaster Plug & Play www.westmountainradio.com 1020 Spring City Drive Waukesha, WI 53186 262-522-6503 sales@westmountainradio.com 2013 West Mountain Radio, All rights reserved. All trademarks are the
More informationGV-Keyboard Instruction Manual
Instruction Manual 005/03 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Table of Contents RX TX Introduction P P P3
More informationSuper UA Q&A 2015/03/16
Super UA Q&A 2015/03/16 Can DSD playback software other than foobar2000 and Audirvana Plus be used? Although operation is not guaranteed, it should be possible to use any DSD playback software that supports
More informationTitanSDR Receiver. Installation Manual v.2.0e
TitanSDR Receiver Installation Manual v.2.0e Enablia S.r.l. (Italy) 2014 Before using the receiver, read carefully this Manual. Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
More informationFldigi Fast Light Digital. Workshop. January 28, 2011 Toledo, Ohio
Fldigi Fast Light Digital Workshop January 28, 2011 Toledo, Ohio What we will cover Session 1 (Today) 1. Hardware needed 2. Software needed 3. Hardware installation 4. Software installation 5. Software
More informationHS6000 Wireless Headset
HS6000 Wireless Headset OPERATING INSTRUCTIONS SETUP Power On/Off To turn the power on Press and release the power button on the inside of the headset housing, shown in Figure 1. A voice message in the
More informationCO1211A/00 Converter Control/Power
Description The is an integrated power supply and controller for Sivers IMA mm-wave converters. It provides proper biasing and allows for control of converter functions using a PC, over a USB connection.
More informationFunction Key ALT CTRL ALT + CTRL CTRL + SHIFT Shift + ALT
PowerSDR keyboard shortcuts. PowerSDR must be in FOCUS (Mouse Click somewhere on the PowerSDR console screen) for the PowerSDR to respond to keyboard input. Function Key ALT CTRL ALT + CTRL CTRL + SHIFT
More informationThe SDR Network Control Box software short user manual.
The SDR Network Control Box software short user manual. 1. Generic information about software. The SDR Network Control Box software it is program that allows user to control over next parameters of AFEDRI
More informationHOW-TO set up the Yaesu FTDX3000 using internal USB interface for Fldigi
Background HOW-TO set up the Yaesu FTDX3000 using internal USB interface for Fldigi 3.23.13 Operating the FTdx3000 and Fldigi using the radios built in USB port. In my PSK31 travels I have encountered
More informationHow to Change the Default Playback & Recording Audio Device. How to Change the Default Playback Device
How to Change the Default Playback & Recording Audio Device Sound is a very important part of our computing experience. We listen to music, do voice chat, watch movies, play games, record sound, etc. In
More informationNN4ZZ CwSkimmer and SDR-Bridge setup A quick start guide
NN4ZZ CwSkimmer and SDR-Bridge setup A quick start guide Revision History 14-Jun-2014 - added Telnet screen 11-Aug-2014 - added additional notes about SmartCat and DAX control panel 20-Jan-2015 - update
More informationTB8100 base station. Task Manager Programming Guide
TB8100 base station Task Manager Programming Guide Application Note TN-1154-AN 15 September 2006 Contents 1 Introduction............................................... 3 1.1 Creating Task Manager Tasks.......................................
More informationNN4ZZ CwSkimmer and SDR-Bridge setup A quick start guide
NN4ZZ CwSkimmer and SDR-Bridge setup A quick start guide Revision History 14-Jun-2014 - added Telnet screen 11-Aug-2014 - added additional notes about SmartCat and DAX control panel 20-Jan-2015 - update
More informationKLIM PUMA USER MANUAL
KLIM PUMA USER MANUAL 0. INTRODUCTION On behalf of the entire KLIM Team, thank you for purchasing our KLIM Puma Gaming Headset. We hope it meets your expectations and that you enjoy using this device.
More informationInterfacing diagram with SUN DR2 CW Skimmer and a Logger Program
Interfacing diagram with SUN DR2 CW Skimmer and a Logger Program SunSDR2 LAN Connection CW Skimmer Software V1.8 (VE3NA) Skimmer1 VAC Skimmer 1 VAC 5 Signal I/Q device Telnet Client 1 Port 7301 Telnet
More informationWireless Open-Source Open Controlled Command and Control System WOCCS Design Project. User Manual
MSD - 2011 Rochester Institute of Technology Wireless Open-Source Open Controlled Command and Control System WOCCS Design Project User Manual Revision 1 P11204 Systems Level User Manual WOCCS User Manual
More informationAutomating Lightroom: Part One Import & Export
Automating Lightroom: Part One Import & Export Lightroom can be semi-automated to make fast work of your imaging workflows. Lightroom can make use of custom User Presets to fast track the Import, Develop
More informationWaves. LoAir. User Guide
Waves LoAir User Guide Table of Contents Chapter 1 Introduction... 3 1.1 Welcome...3 1.2 Product Overview...3 1.3 Concepts and Terminology...4 1.4 Components...5 1.5 Block Diagram...6 Chapter 2 Quick Start
More information«Expert Remote» system
«Expert Remote» system User Manual V1.0 1. Overall structure of the «Expert Remote» system 2 2. ExpertRS on Windows PC 4 3. Router settings to open the port 5 4. ExpertRS on Raspberry Pi3 7 5.1 Remote
More informationRemora Acoustic Recorder
Remora Acoustic Recorder www.loggerhead.com Updated 30 January 2015 1 Part I: Initial Setup IMPORTANT: Install software drivers BEFORE connecting to USB. 1) Install Sound Trap Host Software from CD or
More informationContents. The USB Logic Tool... 2 Programming... 2 Using the USB Logic Tool... 6 USB Logic Tool Features... 7 Device Hardware...
USB Logic Tool Contents The USB Logic Tool... 2 Programming... 2 Using the USB Logic Tool... 6 USB Logic Tool Features... 7 Device Hardware... 11 The USB Logic Tool The device is meant to be a prototyping
More informationWin4K3Suite Documentation V1.35 November 2013
Win4K3Suite Documentation V1.35 November 2013 Thank you for buying Win4K3Suite. The Suite supports the Elecraft K3 and KX3 transceivers, the KPA500 Amplifier, the KAT500 Antenna tuner, the P3 Panadapter
More informationtwisted wave twisted wave [an introduction]
twisted wave information www.twistedwave.com $80 free 30 day trial mac only updated frequently 2 versions available (OSX [more powerful] & ios [more portable]) OSX & ios are different purchases [different
More informationGIANT VOICE Paging Interface
INSTALLATION INSTRUCTIONS GIANT VOICE Paging Interface GV-PGINT Important Note to the Installation Technicians The installation of this product requires careful planning and attention to detail! The installation
More informationInstallation and Operation Manual Model 9A02 Software Version 2.0
Installation and Operation Manual Model 9A02 Software Version 2.0 AccessPCHT Installation and Operation Welcome to the AccessPCHT installation and operation guide. This guide will help you install and
More informationUser Guide for Windows OS
User Guide for Windows OS PanaCast 2 Firmware Update September 2017 X0.3.1.30 This guide explains how to update the firmware on PanaCast 2 for Windows OS. It also shows you how to adjust your PanaCast
More informationVM-3-SM1. Speaker Microphone with Voice Storage. Manual Revision: Covers Software Revisions: VS-1XXX:
VM-3-SM1 Speaker Microphone with Voice Storage Manual Revision: 2012-04-20 Covers Software Revisions: VS-1XXX: 01.53.00 & Higher 1 HARDWARE SPECIFICATIONS Operating Voltage Operating Current: Power Save
More information3 Setup Form. 3.1 Tuning Step Tab. ELAD FDM- SW2 User Manual Rev /2015
3 Setup Form When the button is clicked, FDM- SW2 displays the Setup form. This form contains several settings that control the behavior of the software. The Setup form consists of 12 tabs: 1 Tuning Step
More informationDA-3700 Digital Karaoke Mixing Amplifier with Key Control
DA-3700 MIC 1 MIC 2 ECHO ST MONO VOL LOW HIGH REPEAT DELAY -15 +15 0 10-15 +15 0 10 0 10 Digital Karaoke Mixing Amplifier with Key Control OWNER S MANUAL ST MONO VOL LOW HIGH 0 10-15 +15-15 +15 REPEAT
More informationIntesisBox Modbus Server KILSEN KSA-7xx. User s Manual 08/2013 r1.2 eng
IntesisBox Modbus Server KILSEN KSA-7xx User s Manual 08/2013 r1.2 eng Intesis Software S.L. 2013 All rights reserved. Information in this document is subject to change without notice. The software described
More informationColibriDDC ExtIO.dll
ColibriDDC ExtIO.dll Using ColibriDDC receiver with the third party software Introduction ColibriDDC receiver has a large number of opportunities, which can be fully unleashed by ExpertSDR2 software, but
More informationBlueNote USER S GUIDE
BlueNote USER S GUIDE SAFETY PRECAUTIONS SAFETY PRECAUTIONS To prevent injury and/or damage, take the following precautions: 1 Make sure you keep the antenna away from the mains or high voltage electricity
More informationMemory Keyer for the RockMite
NØXAS PicoKeyer-RM Memory Keyer for the RockMite The PicoKeyer is a single chip, automatic iambic Morse code keyer with two message memories. Perfect for portable or QRP operation or for integrating into
More informationRS-232. ital Measurement Metrology, Inc ECISION IS OUR VISION LEVEL REC SETUP MAX MIN FAST SLOW INTV CLOCK.
A C SETUP MAX MIN CLOCK FAST SLOW INTV REC LEVEL RS-232 Lo = 30 Med= 50 Hi = 80 Auto= 30 POWER-UP OPTIONS 80 db 100 db 130 db 130 db ital Measurement Metrology, Inc ECISION IS OUR VISION 1-866-960-940
More informationRenaming the Projector Adapter Advanced Settings Troubleshooting... 25
010-0730-00 Contents Contents... 2 Introduction... 4 Wireless Range... 4 System Requirements... 4 What's in the Box... 4 Adapter Status Indicators and Details... 5 What s the difference between Wireless
More informationInstallation Guide AT-HDR-EX-70C-KIT
4K HDR HDMI Over HDBaseT TX/RX Kit The Atlona is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma
More informationInternet Video Security Monitoring Systems QUICK START GUIDE SEE WHAT YOU VE BEEN MISSING
Internet Video Security Monitoring Systems QUICK START GUIDE SEE WHAT YOU VE BEEN MISSING Under the copyright laws, this documentation may not be copied, photocopied, reproduced, translated, or reduced
More informationAKELA Vector Network Analyzer (VNA) Quick Start Guide
AKELA Vector Network Analyzer (VNA) Quick Start Guide Copyright AKELA, Inc. 2012, all rights reserved http:\\akelainc.com LabVIEW and LabWindows are registered trademarks of National Instruments Incorporated
More informationINSTALLATION INSTRUCTIONS LKP-957
INSTALLATION INSTRUCTIONS LKP-957 Monitor Keypanel 9330-7101-002 Rev A 3/94 TABLE OF CONTENTS 1.1 GENERAL....................................................... 1-1 1.2 UNPACKING AND INSPECTION..........................................
More informationNetwork Upgrade for the LINK DAC III
Network Upgrade for the LINK DAC III Rev #3 (6/2001) Users Manual Thank you for purchasing the Network Upgrade for your LINK DAC. I am sure you will be very pleased with it. It adds the following new features
More informationUM2268 User manual. ST25RU3993-EVAL board software. Introduction
User manual ST25RU3993-EVAL board software Introduction This document describes the graphical user interface (GUI) software (STSW-ST25RU001) for the ST25RU3993-EVAL board. The ST25RU3993-EVAL board is
More informationTechnical Document. Model: F120 Name: F120 PCBA Service Manual No.: Version: V1.0. Check Sign. Standard Approved
Technical Document Model: F120 Name: F120 PCBA Service Manual No.: Version: V1.0 Drawn Check Sign wanglinwen Standard Approved Amendment Records No. Version Drawn/ Brief Date Reason Amender Introduction
More informationTRBOnet One. User Guide. Version Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA
TRBOnet One User Guide Version 5.2.5 World HQ Neocom Software 8th Line 29, Vasilyevsky Island St. Petersburg, 199004, Russia US Office Neocom Software 15200 Jog Road, Suite 202 Delray Beach, FL 33446,
More informationWindows Live Movie Maker for teachers and faculty
Windows Live Movie Maker for teachers and faculty Step-by-step Get Windows Live Movie Maker Download Download Windows Live Movie Maker at http://windowslive.com/desktop/moviemaker Run After the program
More informationCommLink IV Technical Guide
www.wattmaster.com CommLink IV Technical Guide Table of Contents General Information... 3 CommLink IV Overview...3 Optional IP Module Kit...3 Optional Remote Link II...3 Installing CommLink IV ONLY...3
More informationWorking Model Tutorial for Slider Crank
Notes_02_01 1 of 15 1) Start Working Model 2D Working Model Tutorial for Slider Crank 2) Set display and units Select View then Workspace Check the X,Y Axes and Coordinates boxes and then select Close
More informationInstallation Manual. GSM-3V/AB & ABK V3.5 (1200 keypad) Wiring. Important Notes: SIM card. Installation
-V/AB & ABK V.5 (2 ) Important Notes: ) Before you install this equipment, please read this full manual. Installation Manual Wiring 8) Carefully follow the wiring instructions. 2) Before fully installing
More informationSigfox RF & Protocol Test Procedure RSA-SDR-DONGLE for RC1-UDL-ENC
Version 3.8.0 September 14, 2018 Sigfox RF & Protocol Test Procedure RSA-SDR-DONGLE for RC1-UDL-ENC Public Use Note: Only the last version of this document available on the Sigfox web sites is official
More informationSelection tool - for selecting the range of audio you want to edit or listen to.
Audacity Quick Guide Audacity is an easy-to-use audio editor and recorder. You can use Audacity to: Record live audio. Convert tapes and records into digital recordings or CDs. Edit sound files. Cut, copy,
More informationAntenna Analyzer from EU1KY Software Variante DH1AKF
Antenna Analyzer from EU1KY Software Variante DH1AKF 1 Commissioning (basic settings and calibration) Use Settings> Calibration> Oscillator Test (see 6.3.3) to determine the maximum frequency of the SI5351
More informationSection. Amplifier Description and Operation
Section Amplifier Description and Operation - Amplifier Description - Indicator LED s - Signal Inputs & Outputs - Amplifier Feature Description - Setting the Amplifier DD - 1 MODE ST MN INTERNAL AMP TEST
More informationMemory Keyer for the RockMite
NØXAS PicoKeyer-RM Memory Keyer for the RockMite The PicoKeyer is a single chip, automatic iambic Morse code keyer with two message memories. Perfect for portable or QRP operation or for integrating into
More informationIP7 -SS20. IP Paging Amplifier. Reference Manual
IP7 -SS20 IP Paging Amplifier Reference Manual This page left blank Table of Contents Overview...1 Specifications...2 IP7-SS20 Layout...3 LED Indicators...6 LEDs... 6 LED Status Table... 6 LAN Connector
More informationGetting Started. With the Y-Lynx Starter Kit. of the XEMICS XE1283 Transceiver. Y-Lynx web:
Getting Started With the Y-Lynx Starter Kit of the XEMICS XE1283 Transceiver Y-Lynx e-mail: info@y-lynx.com web: www.y.lynx.com Getting Started with the Y-Lynx XE1283 Starter Kit Table of Contents 1 GENERAL
More informationThis document contains excepts from the MS-DMT User Guide for MARS
This document contains excepts from the MS-DMT User Guide for MARS APPENDIX F: Data Port The management of com ports under Windows is covered in Appendix K to include dealing with Ghost ports. When Data
More informationADMS-7. Operation manual YAESU MUSEN CO., LTD.
ADMS-7 Operation manual YAESU MUSEN CO., LTD. TABLE OF CONTENTS Introduction...2 System Requirements...2 Operating system (OS)...2 CPU...2 RAM (system memory)...2 HDD (Hard Disk)...2 Necessary PC peripheral
More informationRenewable Energy. Getting Started With the LEGO Energy Meter
Renewable Energy Getting Started With the LEGO Energy Meter de LEGO Group. 2010 The LEGO Group. 1 Table of Contents 1. Energy Meter Overview... 3 2. Attaching the Energy Storage... 3 3. Charging and discharging
More informationUDPSDR-TX2 Transmitter
UDPSDR-TX2 Transmitter User s Manual Version 1.1 7 August 2014 Copyright 2014 Zephyr Engineering, Inc 1 HARDWARE DESCRIPTION 2 1.1 UDPSDR-TX2 Connectors, Headers and Jumpers 2 1.1.1 UDPSDR-TX2 Connectors
More informationTroubleshooting. Note. SC485, USB485 and USB485B. Table of Contents.
SC485, USB485 and USB485B Troubleshooting Note www.lightorama.com Use this document if: 1. You want to locate the Windows communications port name being used by the RS485 adapter. 2. You believe the USB
More information