Kvaser Leaf Light v2 User s Guide

Transcription

1 Kvaser Leaf Light v2 User s Guide Copyright Kvaser AB, Mölndal, Sweden Printed Wednesday 13 th September, 2017 We believe that the information contained herein was accurate in all respects at the time of printing. Kvaser AB cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change without notice and should not be construed as a commitment by Kvaser AB.

2 Kvaser Leaf Light v2 User s Guide 2 (24) (This page is intentionally left blank.)

3 Kvaser Leaf Light v2 User s Guide 3 (24) Contents 1 About this manual 4 2 Introduction Welcome to Kvaser Leaf Light v Major features Additional software and documentation Kvaser Leaf Light v2 hardware Hardware installation Firmware Update USB connector CAN channels Power supply LED Indicators Troubleshooting Appendices Technical data CAN connectors CAN bus termination Disposal and Recycling Information 15 6 Legal acknowledgements Usage warning EU Regulatory Compliance Patents, Copyrights and Trademarks Document Revision History 24

4 Kvaser Leaf Light v2 User s Guide 4 (24) 1 About this manual This manual is intended for Kvaser Leaf Light v2 users. This document contains a description of the hardware s properties and general instructions for connecting the device to a computer.

5 Kvaser Leaf Light v2 User s Guide 5 (24) 2 Introduction This section will describe the functions and features of the Kvaser Leaf Light v Welcome to Kvaser Leaf Light v2 Figure 1: Kvaser Leaf Light HS v2 OBDII Kvaser Leaf Light v2 is a reliable low cost product. With a time stamp precision of 100 microseconds it handles transmission and reception of standard and extended CAN messages on the bus. It is compatible with applications that use Kvaser s CANlib. This guide applies to Kvaser Leaf Light v2 devices listed in Table 1. Device Product Number Kvaser Leaf Light v Kvaser Leaf Light HS v2 OBDII Kvaser Leaf Light HS v2 OEM Kvaser Leaf Light HS v2 J Kvaser Leaf Light HS v2 J Type II Kvaser Leaf Light HS v2 M Table 1: Kvaser Leaf Light v2 devices and their EAN numbers. Throughout this document, we use the name Kvaser Leaf Light v2 to mean any one of the different Kvaser Leaf Light v2 products listed in Table 1, unless otherwise noted. 1 For usage of the OEM variant, please also see the Kvaser OEM Device Unlock Guide.

6 Kvaser Leaf Light v2 User s Guide 6 (24) 2.2 Major features USB CAN interface. Quick and easy plug-and-play installation. Supports both 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers. 100% compatible with applications written for other Kvaser CAN hardware with Kvaser CANlib. High-speed CAN connection (compliant with ISO ), up to 1 Mbit/s. Fully compatible with J1939, CANopen, NMEA 2000 R and DeviceNet. Simultaneous operation of multiple devices. 2.3 Additional software and documentation The Kvaser CANlib SDK includes everything you need in order to develop software for Kvaser CAN hardware. The SDK contains full documentation and many sample programs, written in C, C++, C#, Delphi, Python and Visual Basic. All Kvaser CAN interface hardware share a common software API. Programs written for one device type will run without modification on other device types. The latest versions of documentation, software and drivers can be downloaded for free at

7 Kvaser Leaf Light v2 User s Guide 7 (24) 3 Kvaser Leaf Light v2 hardware In this section you can read more about the CAN channels, power supply and LED indicators. 3.1 Hardware installation For the Kvaser Leaf Light v2 to communicate with the host computer, the correct version of the Kvaser driver must be installed. The file kvaser_drivers_setup.exe and instructions can be found on the attached CD but it is recommended that the latest version is downloaded from The Kvaser Leaf Light v2 may then be connected to any available USB port on the host computer. 3.2 Firmware Update Firmware updates and upgrade instructions can be found at Use Kvaser Hardware to see the current firmware version of your Kvaser Leaf Light v USB connector The Kvaser Leaf Light v2 has a standard USB type A connector. 3.4 CAN channels The Kvaser Leaf Light v2 has one CAN Hi-Speed channel with a CAN connector depending on the model. Either a 9-pin D-SUB, a 16-pin OBDII, a 5-pin M12 Male, a 9-pin J Type I, or a 9-pin J Type II connector is used. See Section 4.2, CAN connectors, on Page 12 for details about the pinout.

8 Kvaser Leaf Light v2 User s Guide 8 (24) Figure 2: 9-pin D-SUB CAN connector Figure 3: OBDII CAN connector Figure 4: M12 5-pole Male CAN connector

9 Kvaser Leaf Light v2 User s Guide 9 (24) Figure 5: J Type I CAN connector Figure 6: J Type II CAN connector

10 Kvaser Leaf Light v2 User s Guide 10 (24) 3.5 Power supply The Kvaser Leaf Light v2 is powered from the USB port. 3.6 LED Indicators The Kvaser Leaf Light v2 has two LEDs as shown in Figure 7. Their functions are shown in Table 2. Figure 7: LEDs on the Kvaser Leaf Light v2. LED Function Description PWR (Green) Power Steady light when unit is powered and working. USB configuration Firmware CAN (Yellow) CAN RxTx Status for CAN channel. Blinking once every three seconds when something is wrong with the USB connection. 2 Hz flash if something is wrong with the firmware or configuration. Table 2: LEDs on the Kvaser Leaf Light v Troubleshooting Use Kvaser Hardware in the Control Panel to verify that the computer can communicate with the Kvaser Leaf Light v2. If the firmware version shown is all zeros, there are communication problems. If the LEDs are not flashing or do not light up at all, check the power supply.

11 Kvaser Leaf Light v2 User s Guide 11 (24) 4 Appendices In this section you will find technical information about the Kvaser Leaf Light v2 and its connectors. 4.1 Technical data In Table 3 below you will find the Kvaser Leaf Light v2 s technical specifications. CAN Channels 1 CAN Transceivers TJA1051T (Compliant with ISO ) CAN Controller CAN Bit Rate Time stamp resolution 100 µs Max message rate Error Frame Detection Error Frame Generation Silent mode PC interface Power consumption Hardware configuration Software requirements Dimensions Weight Operating temperature Storage temperature Relative humidity Built into the processor 40 kbit/s to 1 Mbit/s 8000 msg/s Yes No No USB Hi-Speed Typical 90mA Done by software (Plug & Play). Windows XP or later. (For other operating systems, contact Kvaser support.) 35 x 165 x 17 mm for body incl. strain relief 110 g 20 C to +70 C 40 C to +85 C 0 % to 85 % (non-condensing.) Table 3: Technical Specifications.

12 Kvaser Leaf Light v2 User s Guide 12 (24) 4.2 CAN connectors Kvaser Leaf Light v2 devices that use the 9-pin D-SUB connector (see Figure 8) have the pinning described in Table 4. Figure 8: The D-SUB 9 connector pin numbers D-SUB pin number Function 1 Not connected 2 CAN_L 3 GND 4 Not connected 5 Shield 6 Not connected 7 CAN_H 8 Not connected 9 Not connected Table 4: Configuration of the 9-pin D-SUB Kvaser Leaf Light v2 devices that use the 16-pin OBDII plug (see Figure 9) have the pinning described in Table 5. Figure 9: OBDII Connector OBDII pin number Function 4 GND 6 CAN_H 14 CAN_L 16 Not connected Table 5: OBDII pin configuration (showing only connected pins)

13 Kvaser Leaf Light v2 User s Guide 13 (24) Kvaser Leaf Light v2 devices that use the 5-pole male M12 connector have the pinning described in Table 6 on Page 13. Figure 10: 5-pole male M12 Connector M12 pin number Function 1 Shield 2 Not connected 3 GND 4 CAN_H 5 CAN_L Table 6: 5-pole M12 pin configuration Figure 11: J Type I Connector Kvaser Leaf Light v2 devices that use the 9-pin J Type I or Type II connector have the pinning described in Table 7 on Page 14.

14 Kvaser Leaf Light v2 User s Guide 14 (24) Figure 12: J Type II Connector J Pin Function A GND B Not connected C CAN_HI D CAN_LOW E SHIELD F-J Not connected Table 7: J pin configuration 4.3 CAN bus termination Every CAN bus must be terminated with a 120 Ohm resistor at each end of the bus. The Kvaser Leaf Light v2 does not contain any CAN bus termination, because their inclusion could cause severe disturbance in a system which is already correctly terminated. For laboratory or testing use, the exact value of the termination resistors is not always critical. Sometimes a single terminator is sufficient. For production, proper termination is essential. If you see error frames on the bus, you should check the termination. To save yourself a lot of trouble, always terminate the CAN bus properly.

15 Kvaser Leaf Light v2 User s Guide 15 (24) 5 Disposal and Recycling Information When this product reaches its end of life, please dispose of it according to your local environmental laws and guidelines. For information about Kvaser s recycling programs, visit:

16 Kvaser Leaf Light v2 User s Guide 16 (24) 6 Legal acknowledgements 6.1 Usage warning WARNING FOR ALL USERS WARNING! - YOUR USE OF THIS DEVICE MUST BE DONE WITH CAUTION AND A FULL UNDERSTANDING OF THE RISKS! THIS WARNING IS PRESENTED TO INFORM YOU THAT THE OPERATION OF THIS DEVICE MAY BE DANGEROUS. YOUR ACTIONS CAN INFLUENCE THE BEHAVIOR OF A CAN-BASED DISTRIBUTED EMBEDDED SYSTEM, AND DEPENDING ON THE APPLICATION, THE CONSEQUENCES OF YOUR IMPROPER ACTIONS COULD CAUSE SERIOUS OPERATIONAL MALFUNCTION, LOSS OF INFORMATION, DAMAGE TO EQUIPMENT, AND PHYSICAL INJURY TO YOURSELF AND OTHERS. A POTENTIALLY HAZARDOUS OPERATING CONDITION IS PRESENT WHEN THE FOLLOWING TWO CONDITIONS ARE CONCURRENTLY TRUE: THE PRODUCT IS PHYSICALLY INTERCONNECTED TO A REAL DISTRIBUTED EMBEDDED SYSTEM; AND THE FUNCTIONS AND OPERATIONS OF THE REAL DISTRIBUTED EMBEDDED SYSTEM ARE CONTROLLABLE OR INFLUENCED BY THE USE OF THE CAN NETWORK. A POTENTIALLY HAZARDOUS OPERATING CONDITION MAY RESULT FROM THE ACTIVITY OR NON-ACTIVITY OF SOME DISTRIBUTED EMBEDDED SYSTEM FUNCTIONS AND OPERATIONS, WHICH MAY RESULT IN SERIOUS PHYSICAL HARM OR DEATH OR CAUSE DAMAGE TO EQUIPMENT, DEVICES, OR THE SURROUNDING ENVIRONMENT. WITH THIS DEVICE, YOU MAY POTENTIALLY: CAUSE A CHANGE IN THE OPERATION OF THE SYSTEM, MODULE, DEVICE, CIRCUIT, OR OUTPUT. TURN ON OR ACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR FUNCTION. TURN OFF OR DEACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR FUNCTION. INHIBIT, TURN OFF, OR DEACTIVATE NORMAL OPERATION. MODIFY THE BEHAVIOR OF A DISTRIBUTED PRODUCT. ACTIVATE AN UNINTENDED OPERATION. PLACE THE SYSTEM, MODULE, DEVICE, CIRCUIT, OR OUTPUT INTO AN UNINTENDED MODE. ONLY THOSE PERSONS WHO: (A) ARE PROPERLY TRAINED AND QUALIFIED WITH RESPECT TO THE USE OF THE DEVICE, (B) UNDERSTAND THE WARNINGS ABOVE, AND (C) UNDERSTAND HOW THIS DEVICE INTERACTS WITH AND IMPACTS THE FUNCTION AND SAFETY OF OTHER PRODUCTS IN A DISTRIBUTED SYSTEM AND THE APPLICATION FOR WHICH THIS DEVICE WILL BE APPLIED, MAY USE THE DEVICE. PLEASE NOTE THAT YOU CAN INTEGRATE THIS PRODUCT AS A SUBSYSTEM INTO HIGHER-LEVEL SYSTEMS. IN CASE YOU DO SO, KVASER AB HEREBY DECLARES THAT KVASER AB S WARRANTY SHALL BE LIMITED TO THE CORRECTION OF DEFECTS, AND KVASER AB HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY OVER AND ABOVE THE REFUNDING OF THE PRICE PAID FOR THIS DEVICE, SINCE KVASER AB DOES NOT HAVE ANY INFLUENCE ON THE IMPLEMENTATIONS OF THE HIGHER-LEVEL SYSTEM, WHICH MAY BE DEFECTIVE.

17 Kvaser Leaf Light v2 User s Guide 17 (24) 6.2 EU Regulatory Compliance EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director

18 Kvaser Leaf Light v2 User s Guide 18 (24) EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 OBDII Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 OBDII Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director

19 Kvaser Leaf Light v2 User s Guide 19 (24) EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 OEM Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 OEM Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director

20 Kvaser Leaf Light v2 User s Guide 20 (24) EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 J Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 J Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director

21 Kvaser Leaf Light v2 User s Guide 21 (24) EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 M12 Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 M12 Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director

22 Kvaser Leaf Light v2 User s Guide 22 (24) EU Declaration of Conformity (DoC) We Company Name: Postal address: Postcode: City: Telephone number: address: Kvaser AB Aminogatan Mölndal sales@kvaser.com declare that the DoC is issued under our sole responsibility and belongs to the following product: Product: Kvaser Leaf Light HS v2 J Type II Object of the declaration (identification of apparatus allowing traceability): Product: Kvaser Leaf Light HS v2 J Type II Type: The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Chemical substances (REACH) Regulation (EC) No 1907/2006 Electromagnetic Compatibility (EMC) Directive 2014/30/EU RoHS recast Directive 2011/65/EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU The following harmonised standards and technical specifications have been applied: Title, Date of standard/specification: EN (2010) EN (2010) EN ( A1:2011) EN (2012) EN (2005) Signed for and on behalf of: Mölndal Place of issue Date of issue Claes Haglund, Supply Chain and Quality director NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

23 Kvaser Leaf Light v2 User s Guide 23 (24) designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. 6.3 Patents, Copyrights and Trademarks All trademarks are the property of their respective owner. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. DeviceNet is a trademark of Open DeviceNet Vendor Association, Inc. NMEA 2000 is the registered trademark of the National Marine Electronics Association, Inc. For information about Kvaser related CAN patents, see The products described in this document are protected by U.S. patent 5,696,911.

24 Kvaser Leaf Light v2 User s Guide 24 (24) 7 Document Revision History Version history for document UG_98146_leaf_light_v2: Revision Date Changes First version Added chapter CAN bus termination, relative humidity. Updated links and layout Changed layout of references, figures Added ODBII connector information Purchase of CD/USB not possible anymore Power pin on D-SUB and OBDII is not connected Updated compliance text. Added NMEA device Added J1939 device. Renumbered pages, added images Minor update Minor textual changes Added photo of J1939 Type I connector. Replaced with Added Added image of 9-pin D-SUB Updated compliance text, added link to patents Updated EU Declaration of Conformity