96RC-SAS-8P-PE-LS3. Test Report. This report is also applied to the following drives since they are same generation with very similar specification.

Size: px

Start display at page:

Download "96RC-SAS-8P-PE-LS3. Test Report. This report is also applied to the following drives since they are same generation with very similar specification."

Kathryn Sherman
6 years ago
Views:

1 96RC-SAS-8P-PE-LS3 Test Report This report is also applied to the following drives since they are same generation with very similar specification. 96RC-SAS-4P-PE-LS3 Test Requestor Lydia.Liu Job Title Release Date Testing Engineer Tenthy.Zhang Job Title AKDC DQA Engineer Revision V1.0 Approved by Sophie.Song Job Title AKDC DQA assistant manager Release Status Formal Release Page 1 of 25

2 Revision History: Revision Date Revision Description Creator 2013/2/ First version released Tenthy.Zhang Page 2 of 25

3 Content Test Item List Summary... 5 Product Information... 7 Test Platform Test Software Test Item Chapter 1: Function test Device Information confirm Basic function test RAID Level test Rebuild test Drive Interface test LED &Jumpers and Connectors Backup unit test Chapter 2: Compatibility test With OS compatibility test With motherboard compatibility test With PCIE Bus test Chapter 3: Performance test HD Tach HD Tune Read Test Write test Chapter 4: Reliability test Room temperature test Chapter 5: Appendix Page 3 of 25

4 Test Result Definition Item Description Fail No test N/A Limitation Compatibility test properly without any problem. Compatibility test can t work properly and can t meet the product spec, please describe the issue to the Remark item in detail. No test (no test tool or device or driver not ready); please write reason to the Remark item. Spec not support. Compatibility issue Limitation, it needs formal approval mail or other formal reply from PM or Applicant or Manufacturer. Page 4 of 25

5 Test Item List Summary Num. Test item Result Remark Chapter 1 Function test 1.1 Device Information confirm 1.2 Basic function test RAID Level test Rebuild test Drive interface test 1.3 LED &Jumpers and Connectors Fail 1.4 Backup unit test Chapter 2 Compatibility test 2.1 With OS compatibility test 2.2 With motherboard compatibility test 2.3 With PCIE Bus test * Chapter 3 Performance test 3.1 HD Tach 3.2 HD Tune Read test Write test Chapter 4 Reliability test 4.1 Room temperature test Engineer summary: 1. The Manufacture confirmed some indicator LED connector (J1B1/ J3A1/ J6B3/J6B4) cannot indicate, and at present there is no solution to solve this issue. 2. In AIMB-782QG2, connect slot PCIEX1, cannot identify the card. Page 5 of 25

6 Appendix 1: Motherboard List MB/SBC Core Chipset Remark ASMB-782G2 PCE-5127QG2 AIMB-782QG2 FWA-6510 Ivy Bridge C216 Ivy Bridge Q77 Ivy Bridge Q77 Ivy Bridge C216 Appendix 2: HDD List P-TD Part Number Band MN/PN Remark 96HD2000G-ST-SG7K3 Seagate ST2000VX '' SATA HDD 96HDE3T-ST-SG7K Seagate ST3000VX '' SATA HDD 96HD2000G-ST-SG7K1 Seagate ST2000NM '' SATA HDD 96HD500G-ST-SG7K11 Seagate ST500NM '' SATA HDD 96ND1T-ST-WD5KE WD WD10JUCT 3.5'' SATA HDD 96ND500G-ST-WD5KE WD WD500LUCT 3.5'' SATA HDD 96HD1T-ST-WD10KE WD WD1000DHTZ 3.5'' SATA HDD 96HD500G-ST-WD10KE WD WD5000HHTZ 3.5'' SATA HDD Page 6 of 25

7 Product Information Advantech Part Number 96RC-SAS-8P-PE-LS3 Manufacturer LSI Model Number Mega RAID SAS i Device support Up to 128 SATA and/or SAS hard drives and SSDs Number of ports Two Mini-SAS internal connectors (SFF8087) Array interface to the host PCIE3.0 X8 PCI Express bus data transfer rate up to 16GB/S RAID controller LSISAS2208 Dual-Core RAID on Chip (ROC) RAID Levels RAID levels 0, 1, 5, 6, 10, 50, 60 Drive data transfer rate Up to 6Gb/s per port Cache 1 GB 1333MHz DDRIII SDRAM OS Support Windows Vista/Server 2003/2000/XP/7/2008, Linux Operating voltage 3.3V,12V Operating Temperature Maximum ambient: Controller Card: 60 C, with optional CVM01: 55 C, with optional LSIiBBU09: 55 C PCB version NA BIOS version ( ) Card size MD2 Low profile (6.6 X ) ROHS Status (Yes/No) Yes * This report is also applied to the following drives. Advantech PN Manufacturer MN/PN Description 96RC-SAS-8P-PE-LS3 LSI i SAS/SATA 4port 6Gb/s 1GB PCIE3.0X8 (RAID 0, 1, 5, 6, 10, 50,60) * The raid card has select backup unit for testing, as follows: Part Number Manufacturer MN/PN Remark 96RC-IBBU09-LS1 LSI LSIIBBU09 LSIiBBU09 Battery Backup Unit(G) 96RC-CACHE V-LS LSI LSI00297 (LSICVM01) Cache Vault Page 7 of 25

8 Photo: Page 8 of 25

9 96RC-IBBU09-LS1 96RC-CACHE V-LS Page 9 of 25

10 Test Platform MB/SBC ASMB-782G2 PCB version A101-3 CPU Intel i GHz BIOS version S782X024 DRAM Apacer DDR GB DIMM Core Chipset Ivy Bridge C216 Backplane NA VGA Chipset CPU integrated Other MB/SBC PCE-5127QG2 PCB version A101-3 CPU Intel i GHz BIOS version V1.10 DRAM Apacer DDR GB DIMM Core Chipset Ivy Bridge Q77 Backplane PCE-5B12-07_A101-1 VGA Chipset CPU integrated Other MB/SBC AIMB-782QG2 PCB version A101-4 CPU Intel E GHz BIOS version A782X017 DRAM Apacer DDR GBX2 DIMM Core Chipset Ivy Bridge Q77 Backplane NA VGA Chipset CPU integrated Other MB/SBC FWA-6510 PCB version A102-1 CPU Intel E GHz X2 BIOS version V1.20 DRAM Transcend DDR GBX4 DIMM Core Chipset Intel C604 PCH Backplane Riser card NAMB-6510PRC_A102-1 VGA Chipset AST 2300 Other Page 10 of 25

11 Test Software Utilities Version / Description Power On/Off (For Reliability test) mark BurnIn Test Pro (For Reliability test) V7.0 build 1015 HD Tach (For Performance test) V HD Tune (For Performance test) V5.0 Page 11 of 25

12 Test Item Chapter 1: Function test 1.1 Device Information confirm The test ensures the product meets SPEC. Check RAID card properties in GUI Storage Management Utility, and paste the screenshot of test result as below. Test result (MB/SBC: AIMB-782QG2): Page 12 of 25

13 1.2 Basic function test RAID Level test The test ensures the RAID controllers Support for RAID levels can be create and working normally. Please see the test criteria as below: 1. The HDD disk can be detected, and the BIOS of Raid card should show the correct drive model and capacity etc information. 2. Make sure the HDD disk can build Raid, Check Raid disk size should be as below: RAID Level Size fault-tolerant capability Note RAID 0 1+1=2 0 N represent disk RAID 1 1+1=1 1 quantity; RAID =(N-1)*1 1(any one) * 1 meaning is multiplied RAID =2 2 by the single disk capacity. RAID =(N-2)*1 2(Each one of the array) (Table 1) 3. OS can be installed into the RAID disk without any problem. 4. Run Burn-in test 30 minutes with the raid disk, Set disk loading 100%, all disks file size 15%, the result must be passed. 5. Run Power on/off test at least 10 times, RAID cannot lose and boot into the OS. 6. Refer to Table 1 fault-tolerant capability,raid can boot into OS when removed the hard disk. MB/SBC: AIMB-782QG2 Raid level HDD OS Result Remark 96HD2000G-ST-SG7K1 *2 RAID 0 96HD1T-ST-WD10KE *2 96HD2000G-ST-SG7K3 *2 Win bit R2 SP1 96HD1T-ST-WD10KE *2 RAID 1 96ND1T-ST-WD5KE 96ND500G-ST-WD5KE Win7 64bit RAID 5 96HD2000G-ST-SG7K3 *2 96HDE3T-ST-SG7K Win7 32bit SP1 RAID 10 96HD1T-ST-WD10KE *2 96HD500G-ST-WD10KE *2 Win7 64bit Page 13 of 25

14 96HD2000G-ST-SG7K3 *2 RAID 50 96HDE3T-ST-SG7K *2 Win bit SP2 96HD2000G-ST-SG7K1 * Rebuild test Criteria: when a drive fails, the controller firmware automatically replaces and rebuilds the data from the failed drive to the hot spare. Raid level MB/SBC HDD OS Result Remark 96ND1T-ST-WD5KE 96ND1T-ST-WD5KE RAID 1 AIMB-782QG2 96ND500G-ST-WD5KE Win7 64bit Replace 96ND1T-ST-WD5KE RAID 5 ASMB-782G2 96HD2000G-ST-SG7K3 *2 96HDE3T-ST-SG7K Win7 32bit Replace 96HDE3T-ST-SG7K SP1 96HDE3T-ST-SG7K 96HD1T-ST-WD10KE *2 96HD500G-ST-WD10KE RAID 10 AIMB-782QG2 Win7 64bit Replace 96HD500G-ST-WD10KE *2 96HD500G-ST-WD10KE RAID 50 ASMB-782G2 96HD2000G-ST-SG7K3 *2 96HDE3T-ST-SG7K Win HDE3T-ST-SG7K *2 Replace 32bit SP2 96HD2000G-ST-SG7K1 *2 96HDE3T-ST-SG7K Drive Interface test The test ensures each port on the SAS RAID controller supports SAS devices, SATA II devices or both. Criteria: 1. The HDD disk can be detected, and the BIOS of Raid card should show the correct drive model and capacity etc information. 2. OS can be installed into the RAID disk without any problem. 3. Run Burn-in test 30 minutes with the raid disk, Set disk loading 100%, all disks file size 15%, the result must be passed. 4. Run Power on/off test at least 10 times, RAID cannot lose and boot into the OS. MB/SBC: AIMB-782 QG2 Page 14 of 25

15 Drive Raid level HDD OS Result Remark 96ND1T-ST-WD5KE 2.5 SATA RAID 1 96ND500G-ST-WD5KE RAID 0 96HD2000G-ST-SG7K1 *2 Win7 64bit Win bit R2 SP1 3.5 SATA RAID 5 96HD2000G-ST-SG7K3 *2 96HDE3T-ST-SG7K Win7 32bit RAID 10 96HD1T-ST-WD10KE *2 96HD500G-ST-WD10KE *2 Win7 64bit 1.3 LED &Jumpers and Connectors The test ensures whether the LED &Jumpers and Connectors can meet the RAID card spec. 1. LED can work properly as spec define 2. Jumper can work properly as spec define MB/SBC: AIMB-782QG2 Jumper/ Connector Type Test description Result Remark 3-pin shielded header J1A2 SCS Backplane Management connector J1A3 Local Battery Backup Unit connector J1A4 SCS Backplane Management connector Individual PHY and J1B1 Drive Fault Indication header Ports 3 to 0 Ports 7 to 4 Implements an enclosure management module that is No test responsible for providing enclosure management functions for storage enclosures and server backplanes 20-pin connector Connects the LSIiBBU09 unit directly to the RAID controller 3-pin shielded header Implements an enclosure management module that is responsible for providing No test enclosure management functions for storage enclosures and server backplanes 2x8-pin header Connects to an LED that indicates whether a drive is in a fault condition. There is one LED per port. When Fail lit, each LED indicates the corresponding drive has failed or is in the Unconfigured-Bad state. The LEDs function in a direct-attach configuration (there are no Page 15 of 25 Cannot indicates

16 SAS expanders). Direct attach is defined as a maximum of one drive connected directly to each port The interface between the RAID controller and the J2B4 Standard Edge Card connector host system. This interface provides power to the board and an I2C interface connected to the I2C bus for the Intelligent Platform Management Interface (IPMI) J3A1 Drive Activity LED header 2-pin connector Connects to an LED that indicates activity on the drives connected to the controller Fail Cannot indicates J3L1 Remote Battery Backup connector 20-pin connector Connects a remote LSIiBBU09 unit to RAID controller No test J4B1 CacheVault Flash Module DDR3 interface 70-pin connector Connects the RAID controller to a CVFM02 module. The CVFM02 module connects to a remote CVPM02 module J5A1 x4 SAS Port 0 through Port 3 Internal connector SFF-8087 mini SAS 4i internal connector Connects the controller by cable to SAS drives or SATA drives 2-pin connector J5A2 Write-Pending LED header Connects to an LED that indicates when the data in the cache has yet to be written to the storage devices. Used when the write-back feature is enabled J5B1 x4 SAS Ports 4 to 7 Internal connector SFF-8087 mini SAS 4i internal connector Connects the controller by cable to SAS drives or SATA drives J6B1 Advanced Software Options Hardware Key header 3-pin header Enables support for the Advanced Software Options features, which include CacheCade, FastPath, Recovery, and SafeStore disk encryption No test 2-pin connector Lets you bypass the SBR EEPROM J6B2 SBR Bypass header during boot in case the EEPROM contents are corrupt No test or missing J6B3 Global Activity LED header 2-pin header Connects to a single LED that indicates drive activity on either port Fail Cannot indicates Page 16 of 25

17 Onboard Serial J6B4 Universal Asynchronous Receiver/Transmitter 4-pin connector Reserved for LSI use No test (UART) connector J6B5 Global Activity LED header 2-pin header Connects to a single LED that indicates drive activity on either port Fail Cannot indicates Onboard Serial J6B6 Universal Asynchronous Receiver/Transmitter 4-pin connector Reserved for LSI use No test (UART) connector Page 17 of 25

18 1.4 Backup unit test The test ensures the RAID controllers can support the backup unit. Check the backup unit status in GUI Storage Management Utility, and paste the screenshot of test result as below. 96RC-IBBU09-LS1 Test result (MB/SBC: ASMB-782G2): Page 18 of 25

19 96RC-CACHE V-LS Test result (MB/SBC: PCE-5127QG2): Page 19 of 25

20 Chapter 2: Compatibility test 2.1 With OS compatibility test The test ensures mainstream windows OS can be installed into the RAID, and the Raid card can working without any problem. Please see the test criteria as below: 1. OS can be installed into the RAID and the Partition and format function is normal. 2. The RAID Card of driver installation without any problem, and device work normally. 3. Run Burn-in test 30 minutes with the raid disk, Set disk loading 100%, all disks file size 15%, the result must be passed. Test platform ASMB-781 OS Driver Result Windows 7 Ultimate 32bit SP Windows 7 Ultimate 64bit Windows server 2008 Standard 32bit with SP Windows server bit R2 with SP Red Hat enterprise Linux bit With motherboard compatibility test The test ensures the the configuration of RAID solution can work properly with different framework and chipsets of Motherboard. Please see the test criteria as below: 1. The HDD disk can be detected, and the BIOS of Raid card should show the correct drive model and capacity etc information. 2. The RAID configuration can be successfully to create and initialization normal : 3. OS can be installed into the RAID and driver working without any problem. 4. Run Burn-in test 30 minutes with the raid disk, Set disk loading 100%, all disks file size 15%, the result must be passed. 5. Run Power on/off test at least 10 times, RAID cannot lose and boot into the OS. MB/SBC: FWA-6510(use Riser card NAMB-6510PRC_A102-1) Item Level HDD P-TD Part Number MN/PN IN SLOT OS Result Page 20 of 25

21 96HD1T-ST-WD10KE *2 WD1000DHTZ CN5 RAID '' SATA 96HD500G-ST-WD10KE *2 WD5000HHTZ (PCIEX8) Win7 32bit Solution 96HD2000G-ST-SG7K3 *2 ST2000VX000 CN5 Win2008 RAID 5 96HDE3T-ST-SG7K ST3000VX000 (PCIEX8) 64bit R2 SP1 2.5''SATA 96ND1T-ST-WD5KE WD10JUCT CN5 Red hat 6.1 RAID 1 Solution 96ND500G-ST-WD5KE WD500LUCT (PCIEX8) 32bit MB/SBC: ASMB-782G2 HDD Item Level P-TD Part Number MN/PN IN SLOT OS Result 96HD1T-ST-WD10KE *2 WD1000DHTZ PCIE6 RAID '' SATA 96HD500G-ST-WD10KE *2 WD5000HHTZ (PCIEX16) Win7 64bit Solution 96HD2000G-ST-SG7K3 *2 ST2000VX000 PCIE5 Win2008 RAID 5 96HDE3T-ST-SG7K ST3000VX000 (PCIEX16) 32bit SP2 2.5''SATA 96ND1T-ST-WD5KE WD10JUCT PCIE6 RAID 1 Solution 96ND500G-ST-WD5KE WD500LUCT (PCIEX16) Win7 32bit MB/SBC: AIMB-782QG2 HDD Item Level P-TD Part Number MN/PN IN SLOT OS Result 96HD1T-ST-WD10KE *2 WD1000DHTZ PCIEX16_1 RAID '' SATA 96HD500G-ST-WD10KE *2 WD5000HHTZ (PCIEX16) Win7 64bit Solution 96HD2000G-ST-SG7K3 *2 ST2000VX000 PCIEX16_1 RAID 5 96HDE3T-ST-SG7K ST3000VX000 (PCIEX16) Win7 32bit 2.5''SATA 96ND1T-ST-WD5KE WD10JUCT PCIEX16_1 RAID 1 Solution 96ND500G-ST-WD5KE WD500LUCT (PCIEX16) Win7 64bit MB/SBC: PCE-5127QG2 HDD Item Level P-TD Part Number MN/PN IN SLOT OS Result RAID '' SATA Solution RAID 5 2.5''SATA RAID 1 Solution 96HD1T-ST-WD10KE *2 WD1000DHTZ PPCIE2 Win HD500G-ST-WD10KE *2 WD5000HHTZ (PCIEX16) 64bit R2 SP1 96HD2000G-ST-SG7K3 *2 ST2000VX000 PPCIE2 Win7 64bit 96HDE3T-ST-SG7K ST3000VX000 (PCIEX16) 96ND1T-ST-WD5KE WD10JUCT PPCIE2 Win ND500G-ST-WD5KE WD500LUCT (PCIEX16) 32bit SP2 Page 21 of 25

22 2.3 With PCIE Bus test The test ensures whether the PCIE bus can work properly without any error with the raid card. Please see the test criteria as below: 1. Run copy test and the RAID can work normally in OS. 2. Run Power on/off test at least 5 times, RAID cannot lose. MB/SBC Backplane PCIE list Result Remark FWA-6510 Riser card NAMB-6510PRC_A102-1 CN5(PCIEX8) PCIE2(PCIEX4) ASMB-782G2 NA PCIE5(PCIEX16) PCIE6(PCIEX16) PCIE7(PCIEX4) PCIEX16_1(PCIEX16) AIMB-782QG2 NA PCIEX4_1(PCIEX4) PCIEX1_1(PCIEX1) Fail In this slot, cannot identify the card P1PCE1(PCIEX4) PCE-5127QG2 PCE-5B12-07_A101-1 P1PCE2(PCIEX4) P1PCE3(PCIEX4) PPCIE2(PCIEX16) Chapter 3: Performance test RAID information configured: RAID LEVEL RAID 0 RAID 1 RAID 5 RAID 10 HDD Remark P-TD Part Number MN/PN 96HD2000G-ST-SG7K3 ST2000VX RPM/ 64MB 96HDE3T-ST-SG7K ST3000VX RPM/ 64MB 96HD2000G-ST-SG7K3 ST2000VX RPM/ 64MB 96HDE3T-ST-SG7K ST3000VX RPM/ 64MB 96HD2000G-ST-SG7K3 *2pcs ST2000VX RPM/ 64MB 96HDE3T-ST-SG7K ST3000VX RPM/ 64MB 96HD2000G-ST-SG7K3 *2pcs ST2000VX RPM/ 64MB 96HDE3T-ST-SG7K*2pcs ST3000VX RPM/ 64MB Page 22 of 25

23 96HD2000G-ST-SG7K3 *2pcs ST2000VX RPM/ 64MB RAID 50 96HDE3T-ST-SG7K*2pcs ST3000VX RPM/ 64MB 96HD2000G-ST-SG7K1*2pcs ST2000NM RPM/ 64MB 3.1 HD Tach MB/SBC FWA-6510 HD Tach version RAID Level Burst Speed Average Read CPU Utilization Random Access Time (MB/s) (MB/s) (ms) RAID % 11.4 RAID % 14.3 RAID % 12.1 RAID % 10.3 RAID % 10.3 RAID % 12.0 RAID % 14.3 AIMB-782QG2 RAID % 12.0 RAID % 11.2 RAID % HD Tune Read Test HD Tune version 5.0 MB/SBC RAID Level Minimum Transfer Rate (MB/s) Maximum Transfer Rate (MB/s) Average Transfer Rate (MB/s) Access Time (ms) CPU Usage Burst Speed (MB/s) RAID % RAID % FWA-6510 RAID % RAID % RAID % Page 23 of 25

24 RAID % RAID % AIMB-782QG2 RAID % RAID % RAID % Write test HD Tune version 5.0 MB/SBC RAID Level Minimum Transfer Rate (MB/s) Maximum Transfer Rate (MB/s) Average Transfer Rate (MB/s) Access Time (ms) CPU Usage Burst Speed (MB/s) RAID % RAID % FWA-6510 RAID % RAID % RAID % RAID % 83.1 RAID % AIMB-782QG2 RAID % RAID % RAID % Chapter 4: Reliability test 4.1 Room temperature test The test ensures the RAID card can working stable. Please see the test criteria as below: 1. Run power on/off 100 times,successful boot rate 100%; 2. Run mark Burn_in, Set disk loading 100%, all disks file size 15%; The result of all disks should be passed when running Burn_in for 12 hours. Page 24 of 25

MB/SBC RAID Level HDD P-TD Part Number MN/PN OS Result Remark NA ST3000DM001 AIMB-782QG2 RAID 0 96HD1000G-ST-SG7K6 96HD2000G-ST-SG7K2 96HD2000G-ST-SG7K3 *2pcs 96HDE3T-ST-SG7K*2pcs ST1000DM003

25 MB/SBC RAID Level HDD P-TD Part Number MN/PN OS Result Remark NA ST3000DM001 AIMB-782QG2 RAID 0 96HD1000G-ST-SG7K6 96HD2000G-ST-SG7K2 96HD2000G-ST-SG7K3 *2pcs 96HDE3T-ST-SG7K*2pcs ST1000DM003 ST2000DM001 ST2000VX000 ST3000VX000 Win bit R2 SP1 96HD2000G-ST-SG7K1 ST2000NM0011 PCE-5127QG2 RAID 5 96HD2000G-ST-SG7K3 *2pcs 96HDE3T-ST-SG7K*2pcs ST2000VX000 ST3000VX000 Win7 64bit Chapter 5: Appendix The Manufacture confirmed some indicator LED connector (J1B1/ J3A1/ J6B3/J6B4) cannot indicate, and at present there is no solution to solve this issue. Please refer to the mail as below: Page 25 of 25

96HD500G-ST-WD7KE. Test Report. AKDC DQA Engineer. Page 1 of 1

96HD500G-ST-WD7KE. Test Report. AKDC DQA Engineer. Page 1 of 1 96HD500G-ST-WD7KE Test Report This report is also applied to the following drives since they are same generation with very similar specification. 96HD250G-ST-WD7KE Test Requestor Christine.Weng Job Title