WD40PURX-64GVNY0 Test Report

Transcription

1 WD40PURX-64GVNY0 Test Report Initiated by River Lin Approved by Jackie Wang Page 1 of 27

2 Revision History: Date Revision Description Creator 2014/04/28 V1.0 The First version released. Page 2 of 27

3 Test Results Definition: Criteria Fail Limitation N/A No Test Definition Test result pass and function work perfectly. Test fail or can not meet the spec requirement. There are no plans to fix this function. Spec not support or driver not ready. No test tool or device or FW not ready, please write reason to the Remark. Page 3 of 27

4 Test Results Summary: Num. Test Item Result Remark Chapter 1 Function Test 1.01 HDD Function Test 1.02 SATA IDE Mode Test 1.03 SATA AHCI Mode Test 1.04 SATA RAID Mode Test Chapter 2 Software Compatibility Test 2.01 OS and Driver Install Test Chapter 3 Hardware Compatibility Test 3.01 CPU Board Compatibility Test Chapter 3 System Reliability Test 4.01 Power On/Off Test 4.02 Warm Boot Stress Test 4.03 ACPI Cycling Burn-in Test 4.04 Full System, I/O Integrated Stress Test Page 4 of 27

5 Table of Contents Revision History:... 2 Test Results Definition:... 3 Test Results Summary:... 4 Table of Contents... 5 Product Information:... 6 Platform Configuration:... 7 Test Programs: Test Equipments: Chapter 1:Function Test HDD Function Test SATA IDE Mode Function Test SATA AHCI Mode Function Test SATA RAID Mode Function Test Chapter 2:Software Compatibility Test OS and Driver Install Test Chapter 3:Hardware Compatibility Test CPU Board Compatibility Test Chapter 4:System Reliability Test Power On/Off Test Warm Boot Stress Test ACPI Cycling Burn-in Test Full System, I/O Integrated Stress Test Chapter 5:System Performance Test HDD Performance Test Page 5 of 27

6 Product Information: Item. Advantech Part Number Manufacturer Model Number 96HD4TB-ST-WD5KA Western Digital WD40PURX-64GVNY0 Description. From Factory 3.5 Interface Capacity Cache Capacity Rotation Speed(RPM) Host Transfer Rate Bytes per Physical Sector SATAIII 4TB 64MB intellipower 6GB 512(Hst)/4096(Physical) Number of Disks 4 Power On Hour(POH) 8760 Annualized Failure Rate (AFR) <0.9%/ hours /MTBF Voltage Tolerance +5.0V ± 5% and +12.0V ± 10%. Operating Temperature 0 C to 65 C Firmware 80.00A80 Country of Origin Dimension (W x H x D) RoHS Status (Yes/No) Thailand 26.1mm x 147.0mm x101.6mm Yes Page 6 of 27

7 Platform Configuration: PCE-7128 Item. Description. M/B Name PCE-7128 PCB Version. A101-3 BIOS Version. 7128X006 Backplane Model. PCE-5B06-03 Backplane Verson. A101-2 CPU Model/Info Intel Xeon CPU E Memory Type/Info/Size DDR G*2 Apacer 78.B1GCE.AF1 PCH Chipset Intel C226 PCH Graphic Controller Intel HD Graphic GT2 LAN1 Controller Intel I217 LAN2 Controller Intel I210 PCE-5127 Item. Description. M/B Name PCE-5127 PCB Version. A101-3 BIOS Version. 5127X020 Backplane Model. PCE-5B06-03 Backplane Verson. A101-2 CPU Model/Info Intel i GHz Memory Type/Info/Size DDR G*2 Apacer 78.B1GCE.AF1 PCH Chipset Intel QM77 PCH Graphic Controller Intel HD Graphic LAN1 Controller Intel 82579LM LAN2 Controller Intel 82583V AIMB-581 M/B Name Item. AIMB-581 Description. Page 7 of 27

8 PCB Version. A101-3 BIOS Version. CPU Model/Info Memory Type/Info/Size PCH Chipset Graphic Controller Audio Codec LAN1 Controller LAN2 Controller A581X057 Intel i GHz DDR G*2 Apacer 78.B1GCE.AF1 Intel QM67 PCH Intel HD Graphic ALC892 Intel 82579LM Intel 82583V MIO-5271 Item. Description. Project Name. MI PCB Version. A101-3 BIOS Version. 5271X017 EC Version I2865X0101 CPU Model/Info Intel Celenron 1.60GHz Memory Type/Info/Size DDR3L GB Apacer 78.B2GCR.AF10C PCH Chipset Lynx Point-LP PCH QM87 Graphic Controller GT3 Graphics, Generation 7.5 graphics core architecture Audio Codec ALC888S LAN1 Controller Intel i218 LAN2 Controller Intal i210 MIO-5290 Item. Description. Project Name. MIO-5290 PCB Version. A101-2 BIOS Version. 5290X015. EC Code Version. I1809X0100 CPU Model/Info Intel 1.70GHz Memory Type/Info DDR GB Apacer 78.A2GC9.4200C Page 8 of 27

9 Total Memory Size PCH Chipset Graphic Controller Audio Codec LAN1 Controller LAN2Controller 8GB QM77 VGA Function was supported intel PCH ALC892 Intel 82579LM Intel 82583V Page 9 of 27

10 Test Programs: Test Program Version HD Tach V HD Tune Pro V5.5 CrystalDiskMake V3.0.3 ATTO Disk V2.46 PassMark Burn-In Test Pro V7.1 build 1017 PassMark Rebooter V1.3 build 1004 PassMark Sleeper V2.3 build 1009 Power on/off V3.3 Page 10 of 27

11 Test Equipments: Model Power on/off test equipment (ATX/AT) Description Page 11 of 27

12 Page 12 of 27

13 Chapter 1:Function Test 1.01 HDD Function Test Test Purpose: The purpose of SATA test is to analyze and validate the functional performance capabilities quality and stability Test Standard: Please refer to the Project Hardware and BIOS specification Test Tool: 1. SATA cable 2. SATA HDD 3. SATA DVD-ROM Test Criteria: 1. The BIOS must detect SATA devices information. 2. The SATA function can install OS and work well on OS without hang, restart, or blue screen or any problems. 3. The Device Management can not have any exclamation point and question mark. 4. Mark sure pass w/program without any error ocurrs Test Procedure: 1. Insert SATA HDD and DVD-ROM into the DUT 2. The BIOS detect SATA port HD correct information. 3. Install OS and all drivers. 4. SATA HDD can be copy/del/read/write file. 5. Install the PassMark BurnIn Pro program, and setting : (a) Select tests to perform and their duty cycle: Select Disk(s) and Optical Drive(s)/ 100% Loading/Auto Stop After : 30Minutes. (b) Set test preferences: Select Disk -> Select Test this drive/ set File size: 15(% of disk), other setting value keep defaults Preference. (c) Then Press Start selected tests for test. 6. After finished testing, the test result will show on screen. 7. Change other port, and repeat 1~ Test Data: Page 13 of 27

14 Test Item Description Result Remark Post information POST should show the correct model name BIOS information BIOS detect correct information Device Manager Device Management can not have any exclamation point and question mark, and detect correct information Install OS &driver Can install OS and driver SATA Port Mark should all SATA port can detect and reboot shutdown BurnIn Running passmark 30mins 1.02 SATA IDE Mode Function Test Page 14 of 27

15 Test Purpose: The purpose of this test is to ensure the functional of the SATA IDE Mode Test Standard: Please refer to the Project Hardware and BIOS specification Test Tools: 1. SATA HDD 2. SATA DVD-ROM 3. PassMark Burn In test Pro Test Criteria: 1. The BIOS Setting IDE mode for DUT. 2. DUT must install OS and all drivers foride mode without any problems or error occurs Test Procedure: 1. Plug SATA HDD and DVD-ROM into DUT. 2. Setting IDE mode of SATA Mode on BIOS. 3. To install OS and drivers. 4. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show on screen. 5. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat 3times. 6. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat 3times. 7. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat 3times. 8. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can work properly, and repeat 3times. 9. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times Test Data: Test Item Description Result Remark SATA IDE Mode Win7 Ultimate SP1_X86 Installation Test. Win8.1 Pro_X86 Installation Test. ACPI S4 Mode OS shut dowm Warm Boot Test SATA AHCI Mode Function Test Page 15 of 27

16 Test Purpose: The purpose of this test is to ensure the functional of the SATA AHCI Mode Test Standard: Please refer to the Project Hardware and BIOS specification Test Tools: 4. SATA HDD 5. SATA DVD-ROM 6. PassMark Burn In test Pro 7. Intel F6 Install Floppy Driver or AHCI driver on USB flash disk Test Criteria: 3. The BIOS Setting AHCI mode for DUT. 4. DUT must install OS and all drivers for AHCI mode without any problems or error occurs Test Procedure: 10. Plug SATA HDD and DVD-ROM into DUT. 11. Setting AHCI mode of SATA Mode on BIOS. 12. To install OS and drivers, during install process, need to upload AHCI driver from Floppy or USB flash disk. 13. Install PassMark BurnIn Pro program and run 30min. After finished testing, the result will show on screen. 14. Enter S1 mode, the system should be resume from S1 mode. This can work properly, and repeat 3times. 15. Enter S3 mode, the system should be resume from S3 mode. This can work properly, and repeat 3times. 16. Enter S4 mode, the system should be resume from S4 mode. This can work properly, and repeat 3times. 17. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can work properly, and repeat 3times. 18. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times. 19. Setting Enabled Hot Plug SATA Port on BIOS. 20. The DUT SATA should be Hot Plug and work properly, and repeat 3times Test Data: Test Item Description Result Remark SATA AHCI Mode Win7 Ultimate SP1_X64 Installation Test. Win8.1 Pro_X64 Installation Test. ACPI S4 Mode Page 16 of 27

17 OS shut dowm Warm Boot Test. Hot Plug 1.04 SATA RAID Mode Function Test Test Purpose: The purpose of this test is to ensure the functional of the SATA RAID Mode Test Standard: Please refer to the Project Hardware and BIOS specification Test Tools: 1. SATA HDD 2. SATA DVD-ROM 3. PassMark Burn In test Pro 4. Intel F6 Install Floppy Driver or RAID driver on USB flash disk Test Criteria: 1. The BIOS Setting RAID mode for DUT on BIOS. 2. DUT must install OS and all drivers for SATA mode without any problems or error occurs Test Procedure: 1. Setting RAID mode of SATA Mode on BIOS. 2. During boot, Press <Ctrl+I> to enter Intel Rapid Storage Technology - Option ROM and setting RAID 0 Mode. 3. To install OS and driver, during install process need to upload RAID driver from Floppy or USB flash disk should be has no hang, blue screen, or any problems. 4. To install PassMark Burn In test Pro and rn 30min. After finished testing, the result will show on screen. 5. Enter Start-> shutdown on OS, then press power button turn on and boot into OS of DUT. This can work properly, and repeat 3times. 6. Enter Start-> restart on OS, then boot into OS of DUT. This can work properly, and repeat 3times Test Data: Test Item Description Result Remark SATA RAID Mode RAID0 RAID1 Rebuild Page 17 of 27

18 Chapter 2:Software Compatibility Test 2.01 OS and Driver Install Test Test Purpose: The purpose of this test is to ensure the OS compatibility of the DUT Test Standard: Please refer to the Project Hardware and BIOS specification Test Tools: 1. Microsoft OS installation DVD depends on X86/X Test Criteria: 1. The OS X86/X64 installation process must complete without any error occurs. 2. The Server OS X86/X64 installation process must complete without any error occurs. 3. Device Management can not have any exclamation point and question mark Test Procedure: 1. Plug OS DVD or Server OS into DVD-ROM, and start install follow installation process. 2. After finish OS install, install all drivers for the DUT. 3. Make sure drivers of the DUT can install, and device management can not have any unknown device Test Data: Test Item Description Result Remake Win7 Ultimate SP1 x86 Win7 Ultimate SP1 x64 Win8.1 Pro x86 Win8.1 Pro x64 OS Installation English. Driver Installation. Device Management Check. OS Installation English. Driver Installation. Device Management Check. OS Installation English. Driver Installation. Device Management Check. OS Installation English. Driver Installation. Device Management Check. Win Server_2008 R2 OS Installation English. Page 18 of 27

19 Test Item Description Result Remake SP1 Enterprise_x64 Driver Installation. Win Server 2012 Standard_x64 Device Management Check. OS Installation English. Driver Installation. Device Management Check. Page 19 of 27

20 Chapter 3:Hardware Compatibility Test 3.01 CPU Board Compatibility Test Test Purpose: The purpose of this test is to validate and ensure the CPU Board compatibility of the DUT Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. Different Chipsets of CPU Board Test Criteria: 1. With a different CPU board connected. The DUT must without any error occurs. 2. BIOS must detect current information 3. Device Management can not have any exclamation point and question mark Test Procedure: 1. Connect to CPU board and power on. 2. The system should be detected HDD, then install OS and drivers for this. 3. Confirm the all kinds of CPU board should work properly Test Data: Test Item Description CPU board BIOS version PCB Version OS install Result Remark MIO X018 A101-2 Win7/Win8.1/2012 MIO X015 A101-2 Win7/Win8.1 AIMB-581 A581X057 A101-3 Win7/Win8.1 PCE X030 A101-3 Win7/Win8.1/ Server2008R2 PCE X006 A101-3 Win7/Win8.1/Server2008R2/2012 Page 20 of 27

21 Chapter 4:System Reliability Test 4.01 Power On/Off Test Test Purpose: The purpose of this test is to examine and validate the stability of the Power On/Off and AT mode under Widows OS Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. Power on/off test equipment. 2. Power on/off Program Test Criteria: 1. The test msut the Power on / off circling test >= 100 times, booting rate=100% 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any problems. 3. The system must have no any error w/ Program Test Procedure: 1. Connect Power on/off test equipment to DUT for Power on/off test 2. Make sure PSON1 or HW Jumper set as ATX Mode. 3. Make sure BIOS item: After AC power Failure MUST set as "Always Off". 4. Install and execute Power on/off Program, and setting Timer :hr/min/sec on DUT. 5. Setup testing time, and change to zero of run number on Power on/off test equipment. 6. Start power on/off test and pass over100 times. 7. Make sure PSON1 or HW Jumper set as AT Mode 8. Repeat 4~5 and start power on/off test for AT mode and pass over 100 times Test Data: Test Item Description Result Remark Power On/Off test (ATX mode) Power On/Off test (AT mode) 1. BIOS item: After AC power Failure set as "Always Off" 2. H/W jumper set as ATX mode 3. Test at room temperature for 1000 duration cycles 3. Booting rate =100% 1. BIOS item: After AC Power Failure set as "Always Off". 2. H/W jumper set as AT mode 3. Test at room temperature for 1000 duration cycles 4. Booting rate =100% Page 21 of 27

22 4.02 Warm Boot Stress Test Test Purpose: The purpose of this test is to analyze and validate the functional performance capabilities quality and stability of DUT warm boot capability Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. PassMark Rebooter Test Criteria: 1. The test msut the Reboot circling test >= 100 times, booting rate=100% 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any problems. 3. The system must have no any error w/ Program Test Procedure: 1. Install PassMark Rebooter program. 2. Executing program, and setting (a) Maxiimum reboots 100 cycles. (b) Delay Time Out setting before each reboot: 20~25 sec. (c) Enabled Auto load Rebooter at startup. 3. Then start test Cycle Test Data: Test Item Description Result Remark Windows 7 Ultimate SP1 X64 1.Run PassMark Rebooter V1.3 Build Must for 100 duration cycles. 3.Time Out Before reboot:10-25secs 4. Booting rate =100% 4.03 ACPI Cycling Burn-in Test Test Purpose: The purpose of this test is to examine and validate the quality and stability of the DUT ACPI capability Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. PassMark Sleeper V2.3 Build Test Criteria: Page 22 of 27

23 1. The ACPI function test msut run 100 times 2. The DUT must maintain a stable condition without any system crash, hang, blue screen or any other problems Test Procedure: 1. Install PassMark Sleeper on the DUT. 2. Setup ACPI support mode. 3. Press Configuration-> Cycles Settings-> Cycle forever, then press ok. 4. Press Sleeper Now and start test 100 times Test Data: Test Item Description Result Remark Windows 7 Ultimate SP1 X64 1. Run PassMark Sleeper V2.3 build Select "all supported states". (S4) 3. Run for 100 times. The DUT MUST maintain a stable condition after the test has been completed Full System, I/O Integrated Stress Test Test Purpose: The purpose of this test is to examine and validate the quality and stability all IO of the DUT Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. PassMark BurnIn Pro Test Criteria: 1. The Full loading test msut run over 12hours 2. The DUT must maintain a stable condition without any system crash, hang, blue screen, restart or any other problems. 3. The system must have no any error w/ PassMark BurnIn Pro Program Test Procedure: 1. Insert tool into all of IO port on DUT. 2. Install PassMark BurnIn Pro program. 3. Executing BurnIn test, and setting : (a) Select tests toperform and their duty cycle: Setp Auto Stop 720 Minutes, select need to test items (b) Set test preferences: setup need to setting items. (c) All setting finish, press Start selected tests for test. 4. The DUT run program over 12hours Test Data: Page 23 of 27

24 I/O Integrated Stress Test: Windows 7 Ultimate SP1 X64 Test Item Description Result Remark CPU 100% Loading RAM 100% Loading VIDEO 100% Loading 2D Graphics 100% Loading 3D Graphics 100% Loading SATA1 SATA HDD WD 40PURX -64GVNY0File system: NTFS Page 24 of 27

25 Chapter 5:System Performance Test 5.01 HDD Performance Test Test Purpose: The purpose of this test is to ensure the HDD performance of the DUT Test Standard: Please refer to the Project Hardware specification and BIOS specification Test Tools: 1. HD Tach 2. HD Tune Pro 3. CrystalDiskMark 4. AS SSD Benchmark 5. ATTO Disk Benchmark Test Criteria: 1. Executing the BenchmarkTest test item of HD Tach 2. Executing the Benchmark\Read Test of HD Tune Pro. 3. Executing the BenchmarkTest default item of CrystalDiskMark 4. Executing the BenchmarkTest default item of AS AUTO Disk Benchmark Test Procedure: 1. Install HD Tach program. 2. Executing program, then setting Select Storage Device and Long bench (a) Select Storage Device (b) Long bench(32mb zones) (c) Press Run Test. 1. Install and execute HD Tach, setting Select Storage Device and Long bench : (a) Select Storage Device (b) Long bench(32mb zones) 2. Install and execute HD Tune Pro, setting need to test HDD and press Start for test. 3. Install and execute CrystalDiskMark, setting need to test HDD and press All start test. 4. Install and execute ATTO Disk Benchmark, setting Drive need to test HDD and press Start for test. 5. Record all of test results Test Data: HDD Performance (OS:) Test Item HD Tach MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark Page 25 of 27

26 HDD Performance (OS:) Test Item HD Tach MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark HDD Long bench(32mb zones)-random access /(smaller is better) Long bench(32mb zones)-cpu utilization / (%,+/-2%) (smaller is better) Long bench(32mb zones)-average read Long bench(32mb zones)-burst Speed HDD Performance (OS:) Test Item HD Tune Pro 5.5 MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark Burst Speed / (MB/s) Transfer Rate - Min. (MB/s) HDD Transfer Rate - Max. (MB/s) Transfer Rate - Average. (MB/s) Access Time (ms) CPU Utilization (%) HDD Performance (OS:) Test Item HDD Software Read (MB/s) Crystal DiskM ark Write (MB/s) Comment MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark / (unit) Seq K K K QD Seq K K K QD Page 26 of 27

27 HDD Performance (OS:) Test Item Software MIO-5271 MIO-5290 AIMB-581 PCE-5127 PCE-7128 Remark HDD ATTO Disk Benchmark Read (MB/s) Write (MB/s) Page 27 of 27