RTS/TXEN CTS/RXEN RS485 RS232 P 0 P 0 P 0 P 0 P 0 P 0 24 V 0V 24 V. If RS ohm terminator IQ3../.../SER/XNC/...

Transcription

1 00-0 V X RS/XEN CS/EN RS IQ.../.../XNC/... Controller/Interface Important: Retain these instructions CONENS Installation - Mounting... Installation - Configuration... Insertion/Replacement of battery... 7 Disposal... 8 Installation - Mounting Install Install according to IQxact or IQxcite installation instructions section steps to IQxact G00766 IQxcite G0066 Connect Serial Interface If /SER/.., serial interface auxiliary board, fitted Note that only one of the RS or connectors can have a cable connected at any one time in order to comply with Class EMC emission standard (EN , residential, commercial, and light industrial environments). WRNING: Failure to comply with this requirement will reduce the unit to Class (industrial environments); in a domestic environment the unit may cause radio interference, in which case the user may be required to take adequate measures. either wire, wire, or RS part connector with 5 screw terminals fo 0.5 to.5 mm cross section area ( to 0 WG) cable If wire devices maximum IQ../.../SER/XNC/... R or RS either 9 way D type plug 6 RS 7 CS 8 9 X (held high) 5 GND Note pins,6,9 - no connection or RJ socket Note pin - no connection CS RS 5 GND 6 X Note that only one of the two RS connectors can be used at a time R erminator switch ON 0 ohm terminator If RS IQ../.../SER/XNC/... external 00 ohm terminator If wire devices maximum R R R R R R R R erminator switch OFF 00 ohm terminator R R IQ../.../SER/XNC/... R R erminator switch ON 0 ohm terminators If the IQ/XNC/SER controller and its slave units are in the same cabinet using the same power supply, each device should have a good physical earth (ground) connection. Step continued over page IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07

2 IQ../.../XNC/... Installation - Mounting (continued) Connect Serial Interface (continued) If the IQ/XNC/SER controller and its slave units are in different cabinets or use different power supplies (e.g. different USs), the cabinets should be isolated from each other. If the bus is likely to suffer from surge and grounding problems, surge protection should be added. he isolator should be connected to the earth (ground) of the nearest device, the of the isolator and the surge protector should be connected together, and earth (ground) of the surge protector s exposed side (e.g. backbone bus) should be connected as directly as possible to the surge ground or earth bond. Multiple Cabinets terminate at far end Isolating Repeater Surge rotection Cabinet Surge Ground or Earth ond Cabinet R R Isolating Repeater Surge rotection ackbone us to more cabinets terminate at far end Surge Ground or Earth ond IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07

3 00-0 V X IQ../.../XNC/... Installation - Mounting (continued) Connect IQ System Current Loop Network If /LN/.., IQ system current loop Lan auxiliary board, fitted off part connectors with screw terminals for 0.5 to.5 mm cross section area ( to 0 WG) cable polarity independent Network Engineering Manual, 9-75 Cable elden 98 elden 907 rend ////HF/00 (elden 876) rend ////HF/00 (elden 87) 9k6 baud 9k baud No. of Wires 000 m 700 m (090 yds) (765 yds) 000 m 500 m (090 yds) (55 yds) 700 m 50 m (765 yds) (80 yds) 500 m 50 m (55 yds) (70 yds) Using wire method IQ LN Using wire method IQ LN - + R- R+ - + R- R+ - + R- R+ - + R- R+ OU IN earth (ground) screen to convenient input channel screen terminal OU IN 7 N earth (ground) screen to convenient input channel screen terminal 7 N Continue Installation Install according to IQxact installation instructions section step to step 9, or IQxcite installation instructions from section step to section step 0. IQxact G00766 IQxcite G0066 IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07

4 00-0 V V X RS/XEN CS/EN X RS IQ../.../XNC/... Installation - Configuration Continue Installation Complete IQ../.../XNC/... installation instructions sheet and IQxact installation instructions up to section step 9, or IQxcite up to section step 0. IQ../.../XNC/... G009 sheet IQxact G00766 IQxcite G0066 Select erminator Switch osition If /SER/.., serial interface auxiliary board, fitted terminator in circuit wire wire terminator out of circuit RS terminator in either position RS Set current loop Network aud Rate and ddress If /LN/.., IQ system current loop Lan auxiliary board, fitted a, Set address switch 0 SE ddress = =* IQ../LN/XNC/ e.g. ddress = + 6 = 8 NO SE = / = / address = /, to 9, to 9 0,,,0 or >9 *Note that the IQ../LN/XNC/... may also use addresses for its virtual CNC, and for its local supervisor CNC which should also be unique on the Lan. b, Set baud rate switch current loop Lan baud rate = 0 9k = 9K 9K6 e.g. aud Rate = 9k 9k6 = = = IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07

5 00-0 V X IQ../.../XNC/... Installation - Configuration (continued) Check current loop network If /LN/.., IQ system current loop Lan auxiliary board, fitted a X IQ../.../LN/XNC/... X b? IQ../.../LN/XNC/...? c Network ddress 0,, or >9 - + R- R+ IQ LN - + R- R+ - + R- R+ IQ Faulty - + R- R+ IQ LN - + R- R+ IQ../.../LN/XNC/... O Check network cabling for short circuits with a multimeter (NO Megger) Check baud rate. Switch on other nodes until faulty node is found ( ). Correct fault. 5 Create CL pplication Creat CL application using CLool CLool runs within SE IQ../.../XNC CLool ManualC008 CL Manual E0007 If using /SER/, ensure that interface type is set up in the CL application (RS, wire, or wire). See step 8 below. IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07 5

6 00-0 V X RS/XEN CS/EN RS V 00-0 V X RS/XEN CS/EN RS IQ../.../XNC/... Installation - Configuration (continued) 6 Download CL pplication Use CLool or SE to download CL pplication (XNC file) CLool ManualC008 SE Manual E007 Note that if XNC (CL application) file is protected, the installer should send MC address(es) of the targetted controller(s) to the XNC file supplier. On receipt of this data the supplier will send back an unlock code which can be used to authorise the file within SE to run on the designated MC ddress(es). either across IQ system network over Ethernet CLool, SE standard Ethernet connection or across IQ system network using local Ethernet connection local C (Ethernet) connection can be either to adjacent Ethernet hub using standard cable only, or directly to IQ using standard cable and crossover adaptor, XCIE/X. Router Ethernet CLool, SE IQ RJ5 standard Ethernet cable XCIE/X crossover adaptor order separately (XCIE/X/5 pack of 5) Note that downloading IQ CL application is possible through a virtual CNC once the virtual CNC address is set up, and if I addressing is set up correctly in both C and IQ. 7 Check Serial interface type If /SER/.., serial interface auxiliary board, fitted Note perform this step after the Configure IQ step in the main installation instructions Check Serial interface operation 8 If /SER/.., serial interface auxiliary board, fitted Note perform this step after the Configure IQ step in the main installation instructions R R RS either wire wire RS R R R R RS RJ or 9 way D he interface type is set up in the CL application (see step 5 above) LED (yellow) X LED (green) RS/XEN LED (red) CS/EN LED (yellow) CL LEDs activated by CL application Communications LEDs X: (yellow) messages transmitted; flashes while communicating : (yellow) messages received; flashes while communicating RS/XEN: RS - RS ready to send if handshaking selected wire -enabled to transmit wire -in transmit mode (extinguished in receive mode) CS/EN: RS - CS clear to send if handshaking selected wire -enabled to receive wire -permanently extinguished 9 Continue Installation Continue installation according to IQxact installation instructions section step on, or IQxcite installation instructions section step on IQxact G00766 IQxcite G IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07

7 00-0 V V V V V V V 0 V IQ../.../XNC/... Insertion/Replacement of attery (if battery required) Switch Off Isolate I/O O I O WRNING: he connecting leads may be connected to supplies. Isolate before touching. I Open anel Remove uxiliary oard Cover a b c d WRNING: Opening the panel may expose dangerous voltages. 7-IEC Remove battery (if replacing battery) Warning: he lithium battery must not be recharged, disassembled, burnt or short circuited. Misuse may cause explosion or fire. Dispose of carefully (see Section, Disposal, below). Refer to Health and Safety Executive Guidance Note GS. 6 Insert new battery 7 Replace uxiliary oard Cover CR0 V a b CR 0 CR 0 8 Close anel 9 Reconnect Supply to I/O 0 Switch On IQ.../.../XNC/.../US/UL/ is UL rated as UL96 listed open energy management equipment. IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07 7

8 IQ../.../XNC/... Disposal WEEE Directive : t the end of their useful life the packaging, product, and any battery should be disposed of by a suitable recycling centre. Do not dispose of with normal household waste. Do not burn. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell echnologies Sàrl, Ecublens, Route du ois 7,Switzerland by its uthorized Representative, rend Control Systems Limited. rend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes. rend Control Systems Limited.O. ox, Horsham, West Sussex, RH YF, UK. el:+ (0)0 888 Fax:+ (0) rend Control Systems US th venue NE, Redmond, Washington 9805, US. el: (5) , Fax: (5) IQ../.../XNC/... Controller/Interface G009 Issue /C /05/07