BOOKBINDING AREA DOC.

Transcription

1

2 DOC. DATASHEET STATEMENT. The following icons are absolutely designed by Midas independently in 27-SEP. They are not in common use in the LCD industry yet but just used for marking out Midasproducts characteristics quickly and simply without any special meaning. Midas reserves the composing right and copyright. No one else is allowed to adopt these icons without Midas approval. 2. The ISO9 logo used in this document is authorized by SGS ( Midas had already successfully passed the strict and professional ISO9:2 Quality Management System Certification and got the certificate (No.: CN7/44) 3. The technologies/techniques/crafts which denoted by the following icons are not exclusively owned by Midas, but also shared by Midas LCD strategic cooperators, however all these technologies/techniques/crafts have been finally confirmed by Midas professional engineers and QC department. 4. As the difference in test standard and test conditions, also Midas insufficient familiarity with the actual LCD using environment, all the referred information in this DATASHEET (including the icons) only have two functions: 4.: providing quick reference when you are judging whether or not the product meets your requirements. 4.2: listing out definitely the tolerance. SAMPLE APPROVAL document rather than consider this DATASHEET as the standard for judging whether or not the LCD meets your requirements. Once you instruct Midas to a mass-production without definite demand for providing sample before, Midas will disclaim all responsibility if the mass-production is proved not meeting with your requirements. 5. The sequence of the icons is random and doesn t indicate the importance grade. 6. Icons explanation Midas 26 version logo.midas is an integrated manufacturer of flat panel display (FPD). Midas supplies TN, HTN, STN, FSTN monochrome LCD panel; COB, COG, TAB LCD module; and all kinds of LED backlight. F FAST RESPONSE TIME This icon on the cover indicates the product is with high response speed; Otherwise not. PROTECTION CIRCUIT This icon on the cover indicates the product is with protection circuit; Otherwise not. H C HIGH CONTRAST This icon on the cover indicates the product is with high contrast; Otherwise not. LONG LIFE VERSION This icon on the cover indicates the product is long life version (over 9K hours guaranteed); Otherwise not. WIDE VIEWING SCOPE This icon on the cover indicates the product is with wide viewing scope; Otherwise not. UV Anti UV VERSION This icon on the cover indicates the product is against UV line. Otherwise not. RoHS RoHS COMPLIANCE This icon on the cover indicates the product meets ROHS requirements; Otherwise not. YC XC OPERATION TEMPERATURE RANGE This icon on the cover indicates the operating temperature range (X-Y). 3TIMEs % QC EXAMINATION This icon on the cover indicates the product has passed Midas thrice % QC. Otherwise not. TWICE SELECTION OF LED MATERIALS This icon on the cover indicates the LED had passed Midas twice strict selection which promises the product s identical color and brightness; Otherwise not. 3.V Vlcm3.V This icon on the cover indicates the product can work at 3.V exactly; otherwise not. N N SERIES TECHNOLOGY (28 developed) New structure, new craft, new technology and new materials inside both LCD module and LCD panel to improve the "RainBow"

3 STANDARD DOC. REVISION RECORD PAGE /2 NO. DATE DESCRIPTION ITEM PAGE APPROVED INITIAL ISSUED ALL ALL 27.4 Added further information of LED backlight 4 4/2 LU BOO

4 Midas LCD Part Number System MC COG A 4 * W 7 * 8 * 9 S N T L W * * MC: Midas Components 2 Blank: COB (chip on board) COG: chip on glass 3 No of dots 4 Series 5 Series Variant: A to Z see addendum 6 3: 3 o clock 6: 6 o clock 7 S: Normal ( to + 5 deg C) W: Wide temp. (-2 to + 7 deg C) X: Extended temp ( Deg C) 8 Character Set (e.g x 64 dots) (e.g x 6 5mm C.H.) 9: 9 o clock 2: 2 o clock Blank: Standard (English/Japanese) C: Chinese Simplified (Graphic Displays only) CB: Chinese Big 5 (Graphic Displays only) H: Hebrew K: European (std) (English/German/French/Greek) L: English/Japanese (special) M: European (English/Scandinavian) R: Cyrillic W: European (English/Greek) U: European (English/Scandinavian/Icelandic) 9 Bezel Height (where applicable / available) Top of Bezel to Top of PCB Blank A B D E F G 9.5mm / not applicable 8.9 mm 7.8 mm 7.8 mm 9.5 mm 7 mm 7 mm 6.4 mm 6.4 mm 5.5 mm 5.5 mm 6.mm 5.mm 4.7mm 3.7mm Common (via pins and 2) Array or Edge Lit Common Array Common Separate Common Separate Common Separate Common Separate Common Separate Separate Separate Common Separate Array Array Array Array Array Array Edge Edge Edge Edge Edge Edge Edge EL T: TN S: STN B: STN Blue G: STN Grey F: FSTN F2: FFSTN P: Positive N: Negative 2 R: Reflective M: Transmissive T: Transflective 3 Backlight: Blank: Reflective L: LED 4 Backlight Colour: Y: Yellow-Green W: White B: Blue R: Red A: Amber O: Orange G: Green RGB: R.G.B. 5 Driver Chip: 6 Voltage Variant: e.g. 3 3v Blank: Standard I: I2C T: Toshiba T6963C A: Avant SAP24B R: Raio RA6963

5 STANDARD DOC. CONTENTS PAGE 3/2. GENERAL SPECIFICATIONS Page 4 2. MECHANICAL SPECIFICATIONS Page 4 3. ABSOLUTE MAXIMUM RATINGS Page 4 4. ELECTRONICAL CHARACTERISTIC Page 4 5. OPTICAL CHARACTERISTICS Page 5 6. ELECTRICAL SPECIFICATIONS Page 6 7. EXTERNAL DIMENSION Page 8 8. PIN ASSIGNMENT Page 9 9. POWER SUPPLY Page 9. REFLECTOR OF SCREEN AND DDRAM ADDRESS Page 9. INSTRUCTION TABLE Page 2. INSTRUCTION DESCRIPTION Page 3. CGRAM Page 5 4. DDRAM Page 5 5. INITIALIZATION Page 6 6. INTERFACE TO MPU Page 8 7. FONT MAP Page 9 8. PACKING DETAIL Page 2

6 PAGE 4/2. GENERAL SPECIFICATIONS ITEM NOMINAL DIMENSIONS / AVAILABLE OPTIONS DISPLAY FORMAT 22 X 32 DOT MATRIX LCD PANEL OPTIONS STN ( Yellow-Green color) POLARIZER OPTIONS Positive, Transflective BACKLIGHT OPTIONS Array type LED backlight (Yellow-Green color) VIEWING ANGLE OPTIONS 6:(Bottom) TEMPERATURE RANGE OPTIONS CONTROLLER IC DISPLAY DUTY Wide temperature range ( - 2 C ~ 7 C ) AVANT /32 DRIVING BIAS /7 2. MECHANICAL SPECIFICATIONS OVERALL SIZE LED backlight version : 84. x 44. x max 5. mm VIEWING AREA 64.W x 7.9H mm HOLE-HOLE 76.W x 36.H mm DOT SIZE.4W x.45h mm DOT PITCH.4W x.4h mm WEIGHT (EL BKL) 86. g WEIGHT (LED BKL) 5. g 3. ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL CONDITION MIN MAX UNIT POWER SUPPLY ( LOGIC) Vdd 25 C V POWER SUPPLY (LCD) V 25 C Vdd -3.5 Vdd +.3 V INPUT VOLTAGE Vin 25 C -.3 Vdd +.3 V OPERATING TEMPERATURE Vopr -2 7 C STORAGE TEMPERATURE Vstg -3 8 C 4. ELECTRONICAL CHARACTERISTIC* STANDARD ITEM SYMBOL CONDITION UNIT MIN TYP MAX Input voltage Vdd +5V V Supply current Idd Vdd5V.9 ma -2 C Recommended LCD driving C voltage for normal temp. Vdd-V 25 C V Version module 5 C C LED forward voltage Vf 25 C V LED forward current If 25 C 2 ma LED reverse Current Ir 25 C 6 A LED Peak wave length p 25 C If 2mA nm LED illuminance (Without LCD) Lv C If 2mA cd/m 2 LED life time 25 C If 2mA 9K** Hours * The above data are for reference only. ** If you wanted to drive the LED BKL uninterruptedly exceed 2hours/day, you are not suggested this version

7 PAGE 5/2 5. OPTICAL CHARACTERISTICS FOR TN TYPE LCD MODULE (T A25 C, Vdd5.V.25V) ITEM SYMBOL CONDITION MIN TYP MAX UNIT VIEWING ANGLE 2 _ 3 K4 25 deg CONTRAST RATIO K 2 RESPONSE TIME(RISE) TR 2 5 ms RESPONSE TIME(FALL) TF 2 5 ms FOR STN TYPE LCD MODULE (T A25 C, Vdd5.V.25V) ITEM SYMBOL CONDITION MIN TYP MAX UNIT VIEWING ANGLE 2 _ 4 K4 6 deg CONTRAST RATIO K 6 RESPONSE TIME(RISE) TR 5 25 ms RESPONSE TIME(FALL) TF 5 25 ms DEFINITION OF ANGLE & DEFINITION OF VIEWING ANGLE & 2 Y( 8 ) 2 Contrast Ratio K X X`.4 Y( ) 2 Viewing Angle DEFINITION OF CONTRAST RATIO K(B 2/B ) DEFINITION OF OPTICAL RESPONSE TIME T R& T F Brightness(%) Brightness Curve for selected Segment B2 B Brightness Curve for Non- selected Segment Setpoint Driving Voltage Non-Select Select Signal Brlghtness(%) 9% % TR Rise Time Non-Select TF % Fall Time Time(ms)

8 PAGE 6/2 6. AC CHARACTERISTIC V dd 5.V+ %,V SS V,T a -2~+75C Parameter Symbol Min Max Condition Unit Address set up time t AW6 2 ns Address hold time t AH6 ns System cycle time t CYC6 ns E pulse width Read ns t EW Write 8 ns Data set up time t DS6 8 ns Data hold time t DH6 ns Access time t ACC6 9 ns C L pf Output disable time t OH6 6 ns *Input signal rise time and fall time are less than 5ns. E t CYC6 t AW6 t EW R/W t AH6 A t DS6 t DH6 D~D7 (WRITE) t ACC6 t OH6 D~D7 (READ)

9 PAGE 7/2 7.EXTERNAL DIMENSIONS T2 T O.S. P2.54 X9 22X32DOTS ITEM T T2 UNIT LED backlight mm EL or without backlight 4.8. mm PL V.A H.H O.S H.H V.A PL

10 PAGE 8/2 8. PIN ASSIGNMENT PIN NO. SYMBOL FUNCTION Vss V 2 Vdd Power Supply +5V 3 V Contrast Adjust 4 A H/L H: Data; L: Instruction code 5 CS Chip Enable signal 6 CS2 Chip 2 Enable signal 7 CL Clock Input (2K Hz) 8 E Enable Signal 9 R/W Read / Write DB Data Bit DB Data Bit 2 DB2 Data Bit 2 3 DB3 Data Bit 3 4 DB4 Data Bit 4 5 DB5 Data Bit 5 6 DB6 Data Bit 6 7 DB7 Data Bit 7 8 RST Reset Signal 9 LED+ Anode of LED Unit 2 LED- Cathode of LED Unit REMARK +5V V 9..BLOCK DIAGRAM 9.2. POWER SUPPLY Vss Vdd V A CS R/W /RST E CL DB DB7 U SEG-6 SEG-6 COM-6 COM SEG62-22 SEG62-22 SINGLE SUPPLY TYPES VSS V VDD CK FR COM7-32 COM6 COM7 COM32 22X32 LCD PANEL RPOT V DD ~ V CS2 U2 SEG62-22 VDD +5V Pin9 Pin2 R LED BACKLIGHT VDD-VO: LCD DRIVING VOLTAGE RPOT: K-2K

11 PAGE 9/2. RELATION BETWEEN DISPLAY PATTERN AND DRIVERS U Display Area PAGE 8X8 Bits U2 Display Area PAGE 2 8X8 Bits COM PAGE 3 8X8 Bits SEG SEG 6 PAGE 4 8X8 Bits COM32 SEG6 SEG 22 22X32 Dots Matrix Y Y2 D D D2 D3 D4 D5 D6 D7 Y3 Y32 Starting dot for the starting address of display RAM. Each segment driver has 4 pages RAM, and each page has 8x8 bits RAM. D~D7 are 8 bits transmitted data, where D is LSB and D7 is MSB. 6 COM COM6 SEG 22X32 GRAPHIC LCD PANEL COM7 COM32 SEG U SBN66G_M2 U2 SBN66G_M2

12 PAGE /2. INSTRUCTIONCODE Instruction Display on/off Display Start line Page address set Column address set Status read Write display data Read display data ADC select Static drive on/off Duty ratio select Read Modify write END Reset Power save (dual command) A R/W D7 D6 D5 D4 D3 D2 D D Description / DISPLAY START ADDRESS (-3) Page (-3) Column address(-79) B U S Y A D C O N / O F F R E S E T / / / Write data Read data Whole disp on/off : on : off Determine the disp line correspond to the COM Set the page of disp data RAM Set the column address of disp data RAM BUSY : ready : working ADC : counter clockwise ; clockwise output ON/OFF : disp on : disp off RESET ; normal : reset Write data to disp RAM Read data from disp RAM Access the predetermind address of the disp RAM Determine the mode reading of the disp RAM : clockwise output : counter clockwise output Select the dynamic or static driving : static driving : dynamic driving Select the duty ratio : /6 : /32 Increment the column address register when writing but no change when reading Release from the Read Modify Write mode Set the display start line register to st line, page add register to 3. Set the power save mode by selecting disp off and static driving on.

13 PAGE /2 2. INSTRUCTION DESCRIPTION A. DisplayOn/Off This is instruction executes whole display On/Off no relation with the data in the Display Data RAM and internal conditions. A R/W D7 D6 D5 D4 D3 D2 D D D D : Display On : Display Off When the static driving mode is selected ( static drive On ) in display Off status, the internal circuits put on the power save mode. B. Display Start Line This instruction set the line address. The selected line in the Display Data RAM correspond to the COM which display at the top of LCD panel The display area is set automatically from the selected line to the line which increased the one or page switching are available by this instruction. A R/W D7 D6 D5 D4 D3 D2 D D A4 A3 A2 A A A4 A3 A2 A A Line Address E F

14 PAGE 2/2 C. Page Address Set When MPU access the display Data RAM, the page address corresponded to the row address must be selected. The access in the display Data RAM is available by setting the page and column address. The display is no change when the page address is changed. A R/W D7 D6 D5 D4 D3 D2 D D A A A A Page 2 3 D. Column Address Set This instruction set the column address in the Display Data RAM. When the MPU access the Display Data RAM continuously, the column address increase automatically, therefore, the MPU can access the data only without address setting. The increment of the column address is stopped by the address of 5H automatically, but the page address is no change even if the column address increase to 5H and stop. A R/W D7 D6 D5 D4 D3 D2 D D A6 A5 A4 A3 A2 A A A6 A5 A4 A3 A2 A A ColumnAdd. 4E 4F

15 PAGE 3/2 E. Status Read This instruction read out the internal status. BUSY: ADC: A R/W D7 D6 D5 D4 D3 D2 D D BUSY ADC ON/OFF RESET BUSY indicate the operating or the Reset cycle The instruction can be input after the BUSY status change to. Indicate the output correspondence of column ( segment ) address and segment driver. : Counter clockwise Output (Inverse) Column Address 79 - n Segment Driver n : Clockwise Output (Normal) Column Address n S Segment Driver n ON/OF: Indicate the whole display On / Off status. : Whole Display On : Whole Display Off ( Note) ThedataOnandOffofDisplayOn/Offstatusreadoutisinvertedwith thedisplayon/offinstructiondataofonandoff RESET: Indicate the initialization period by reset instruction. : :Initialization Period F. Write Display Data This instruction write the 8-bit data on the data bus into the Display RAM. The column ( segment ) address increase automatically when writing, therefore, the MPU can write the 8-bit data into the Display Data RAM without address setting. 6SEG A R/W D7 D6 D5 D4 D3 D2 D D WriteData

16 PAGE 4/2 G. Read Display Data This instruction read out the 8-bit data from Display Data RAM which addressed by the column and page address. In case of the Read Modify Write Mode is Off, the column address increase automatically after each read out, therefore, the MPU can read out the 8-bit data from the Display Data RAM continuously without address setting. A R/W D7 D6 D5 D4 D3 D2 D D Read Data H. ADC Select This instruction set the correspondence of column address in the Display Data RAM and segment driver out. Therefore, the order fo segment output can be changed by the software, and no restriction of the LSI placement against the LCD panel. A R/W D7 D6 D5 D4 D3 D2 D D D D : Clockwise Output (Inverse) : Counter Clockwise Output (Normal) I. Static Drive On/ Off This instruction executes the all common output terms on and whole display on obligatory A R/W D7 D6 D5 D4 D3 D2 D D D D : Static Drive Off (Normal Operation) : Static Drive On (Whole Display Turns On) When the Display Off mode is selected ( Display Off ) in Static Driver On status, the internal circuits put on the power save mode.

17 PAGE 5/2 J. Duty ratio Select This instruction set the LCD driving duty ratio. A R/W D7 D6 D5 D4 D3 D2 D D D D : /6 Duty : /32 Duty K. Read Modify Write After this instruction is executed, the column address increase automatically when Display Data Write Instruction execution, but the address is not changed when the Display Data Read Instruction execution. This status continues during End instruction execution. When the End instruction is entered the column address back to the address where Read Modify Write instruction entering. By this function, the load of MPU for example cyclic data writing operation like as cursor blink etc., can be reduced. A R/W D7 D6 D5 D4 D3 D2 D D (Note) During the Read Modify Write mode, any instruction except Column Address Set can be executed.

18 PAGE 6/2 L. Sequence of cursor display Page Address Set Column Address Set Read Modify Write Dummy Read Data Read Data Write No Finish? END Yes

19 PAGE 7/2 M. End This instruction release the Read Modify Write mode and the column address back to the address where the Read Modify Write mode setting. A R/W D7 D6 D5 D4 D3 D2 D D Column Address Return n n+ n+2 n+m n Read Modify Write End N. Reset This instruction executes the following initialization. INitialization ) Set the first line in the Display Start Line Register. 2) Set the page 3 in the Page Register. In this time, there are no influence to the Display Data RAM. A R/W D7 D6 D5 D4 D3 D2 D D (Note) The initialization when the power terms on can not be executed by Reset instruction O. Power Save ( Dual Command ) When both of Display Off and Static Drive On are executed, the internal put on the power save mode and the current consumption is reduced as same as stand by current. The internal status in this mode are as following: ) Stop the LCD driving. Segment and Common drivers output Vdd level 2) Stop the oscillation or inhibit the external clock input 3) Keeping the display data and operating mode. The power save mode is released by Display on or static drive off instruction.

20 PAGE 8/2 3. APPLICATION EXAMPLE Application Flowchart Display on Set display start line Set page address Set column address Set duty ratio Set ADC Write data Application Circuit M L O C D D U L E E E2 R/W A D~D7 Vdd Vss 8 P3.2 P3.4 P3. P3. P.~P.7 3 Vdd Vss (6M Hz)

21 PAGE 9/2 Application Circuit P.~ A A A7~4 G D~7 R/W A RD WR 8 2 E 2 E2 Application Circuit 2 P.~ A A 8 D~7 R/W A A7 Vcc RD WR E A6 Vcc E2

22 PAGE 2/2 4. PACKING DETAIL WITH LED BKL 45 PCS/BOX BOXES/CARTON 45 PCS/CARTON 2. KGS/CTN(G.W.) 3.7 M /CARTON WITHOUT LED BKL 45 PCS/BOX BOXES/CARTON 45 PCS/CARTON 8. KGS/CTN(G.W.) 3.7 M /CARTON NOTE. The weight is estimated for reference only. 2. Packing detail may be changed without notice. Anti - static Bag LCD Module BOX CARTON