2U Server. User Manual

Transcription

1 2U Server User Manual

2 The information in this User Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at Inaxsys Security Systems Inc. reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Inaxsys Security Systems Inc. and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license. IN NO EVENT WILL INAXSYS SECURITY SYSTEMS INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, INAXSYS SECURITY SYSTEMS INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of the province of Québec, Canada. The province of Québec shall be the exclusive venue for the resolution of any such disputes. Inaxsys total liability for all claims will not exceed the price paid for the hardware product. California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate Material-special handling may apply. See WARNING: Handling of lead solder materials that may be used in this product or other products may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Unless you request and receive written permission from Inaxsys Security Systems Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright 2013 by Inaxsys Security Systems Inc. All rights reserved.

3 Preface About This Manual This manual is written for certified technicians. It provides information for the installation and use of the 2U Server. Installation and maintenance should be performed by experienced technicians only. 2U Server features a unique and highly optimized design. The server is equipped with a 560W (single), 563W (single) 600W (single), 700W (redundant) 710W (single), 720W (redundant) or 740W (redundant) high-efficiency power supply for superb power savings. High-performance fans provide ample optimized cooling for the server. This document lists compatible parts and configurations available when this document was published. Always refer to our Web site for updates on supported parts and configurations.

4 Manual Organization Chapter 1 Introduction The first chapter provides a checklist of the main components included with this server and describes the main features of the 2U Server. Chapter 2 System Safety This chapter lists warnings, precautions, and system safety. You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed before installing this server. Chapter 3 Server Components Refer here for details on this server model including the fans, bays, airflow shields, and other components. Chapter 4 System Interface Refer to this chapter for details on the system interface, which includes the functions and information provided by the control panel on the server as well as other LEDs located throughout the system. Chapter 5 Server Setup Refer to this chapter for detailed information on this server. You should follow the procedures given in this chapter when installing, removing, or reconfiguring your server. Chapter 6 Rack Installation Refer to this chapter for detailed information on server rack installation. You should follow the procedures given in this chapter when installing, removing or reconfiguring your server into a rack environment.

5 1-1 Overview Inaxsys 2U Server features a unique and highly-optimized design. The server is equipped with high efficiency power supply. 1-2 Server Features The 2U Server, high-performance server includes the following features: CPU The 2U Server supports a dual-core Xeon processor. Hard Drives The 2U Server features eight slots for SAS/SATA drives. These drives are hot-swappable. Once set up correctly, these drives can be removed without powering down the server. In addition, these drives support SES2 (SAS/SATA). I/O Expansion slots Each 2U Server model includes seven low-profile I/O expansion slots. Peripheral Drives Each 2U Server supports one slim DVD-ROM drive (optional) and one slim floppy drive (optional). These drives allow you to quickly install or save data. Other Features Other onboard features are included to promote system health. These include various three cooling fans, a convenient power switch, reset button, and five LED indicators.

6 1-3 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling our technical support at for a Returned Merchandise Authorization (RMA) number. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete. Whenever possible, repack the server in the original Inaxsys carton, using the original packaging material. If these are no longer available, be sure to pack the server securely, using packaging material to surround the server so that it does not shift within the carton and become damaged during shipping. This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration, misuse, abuse or improper maintenance of products. During the warranty period, contact your distributor first for any product problems.

7 Standardized Warning Statements for AC Systems 2-1 About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact our Technical Support department for assistance. Only certified technicians should attempt to install or configure components. Read this appendix in its entirety before installing or configuring components in the Inaxsys server. Warning Definition This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Installation Instructions Read the installation instructions before connecting the system to the power source. Circuit Breaker This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. Power Disconnection Warning If ever the server is no longer under guarantee and you must open it, the system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the server interior to install or remove system components. Equipment Installation Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Restricted Area This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. (This warning does not apply to workstations).

8 Battery Handling There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Redundant Power Supplies This unit might have more than one power supply connection. All connections must be removed to deenergize the unit. Backplane Voltage Hazardous voltage or energy is present on the backplane when the system is operating. If ever the server is no longer under guarantee and you must open it, use caution when servicing. Comply with Local and National Electrical Codes Installation of the equipment must comply with local and national electrical codes. Product Disposal Ultimate disposal of this product should be handled according to all national laws and regulations. Hot Swap Fan Warning If ever the server is no longer under guarantee and you must open it, the fans might still be turning when you remove the fan assembly from the server. Keep fingers, screwdrivers, and other objects away from the openings in the fan assembly's housing. Power Cable and AC Adapter When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any other electrical devices than products designated by Inaxsys only.

9 Server Components 3-1 Overview This chapter describes the most common components included with your server. Some components listed may not be included or may not be compatible with your particular server model. For more information, see the installation instructions detailed later in this manual. 3-2 Components Server The 2U Server includes eight hard drive bays. Hard drives must be purchased separately. This server supports a 2U backplane, three fans and one or two power supplies. 2U Server models come in silver or black. Backplane Each 2U Server comes with a 2U backplane. Depending on our order, your backplane will accept SAS/SATA or SCSI. Fans The 2U Server supports three system fans. System fans for 2U Server are powered from the motherboard. These fans are 2U high and are powered by 3-pin connectors. Mounting Rails The 2U Server can be placed in a rack for secure storage and use. To setup your rack, follow the step-bystep instructions included in this manual. Power Supply Each 2U Server model includes a high-efficiency power supply rated at 560W (single), 563W (single) 600W (single), 700W (redundant) 710W (single), 720W (redundant) or 740W (Redundant). In the unlikely event your power supply fails, replacement is simple and can be accomplished without tools. Air Shroud Air shrouds are shields, usually plastic, which conduct the airflow directly to where it is needed. If ever the server is no longer under guarantee and you must open it, always use the air shroud included with your server. 3-3 Where to get Replacement Components Although not frequently, you may need replacement parts for your system. To ensure the highest level of professional service and technical support, we strongly recommend purchasing exclusively from our Inaxsys Authorized Distributors / System Integrators / Resellers.

10 System Interface 4-1 Overview There are LEDs on the control panel and the drive carriers to keep you constantly informed of the over-all status of the system, as well as the activity and health of specific components. Most 2U Server models have two buttons on the server control panel: a reset button and an on/off switch. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take. 4-2 Control Panel Buttons There are two push-buttons located on the front of the server. These are (in order from left to right) a reset button and a power on/off button. Reset: The reset button is used to reboot the system. Power: The main power switch is used to apply or remove power from the power supply to the server system. Turning off system power with this button removes the main power but keeps standby power supplied to the system. Therefore, you must unplug system before servicing.

11 4-3 Control Panel LEDs The control panel located on the front of the 2U Server has five LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take. Power Failure: When this LED flashes, it indicates a power failure in the power supply. Overheat/Fan Fail: When this LED flashes it indicates a fan failure. When continuously on (not flashing) it indicates an overheat condition, which may be caused by the ambient room temperature being too warm. Make sure all fans are present and operating normally. You should also check to make sure that the server covers are installed. Finally, this LED will remain flashing or on as long as the overheat condition exists. NIC2: Indicates network activity on GLAN2 when flashing. NIC1: Indicates network activity on GLAN1 when flashing. HDD: Indicates IDE channel activity in the SAS/SATA drive, SCSI drive, and/or DVD-ROM drive activity when flashing. Power: Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating.

12 4-4 Drive Carrier LEDs Your server uses SAS/SATA or SCSI drives, but not both. SAS/SATA Drives Each SAS/SATA drive carrier has two LEDs. Green: Each Serial ATA drive carrier has a green LED. When illuminated, this green LED (on the front of the SATA drive carrier) indicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that particular drive is being accessed. Red: The red LED indicates a SAS/SATA drive failure. If one of the SAS/SATA drives fail, you should be notified by your system management software.

13 Server Setup 5-1 Overview This chapter covers the steps required to install components. The only tool you will need to install components is a Phillips screwdriver. Print this page to use as a reference while setting up your server. 5-2 Installation Removing the Server Cover Installing Hard Drives Front Bezel Review the warnings and precautions listed in the manual before setting up this server. These include information in Chapter 2: System Safety and the warning/precautions listed in the setup instructions. 5-3 Removing the Server Cover Removing the Server Cover 1. Remove the two screws on each side of the cover, which secure the cover to the server. 2. Press the release tabs to remove the cover from the locked position. Press both tabs at the same time. 3. Once the top cover is released from the locked position, slide the cover toward the rear of the server. 4. Lift the cover off the server. Warning: Except for short periods of time, do NOT operate the server without the cover in place. The server cover must be in place to allow proper airflow and prevent overheating.

14 5-4 Installing Hard Drives Removing Hard Drive Trays from the Server 1. Press the release button on the drive carrier. This extends the drive carrier handle. 2. Use the handle to pull the drive out of the server. The drives are mounted in drive carriers to simplify their installation and removal from the server. These carriers also help promote proper airflow for the drive bays.

15 Installing a Hard Drive to the Hard Drive Carrier 1. Remove the screws securing the dummy drive to the carrier. 2. Remove the dummy drive from the carrier. Warning: Except for short periods of time (swapping hard drives), do not operate the server with the hard drives removed from the bays. 3. Install a new drive into the carrier with the printed circuit board side facing down so that the mounting holes align with those in the carrier.

16 4. Secure the hard drive by tightening all six screws. 5. Replace the drive carrier into the server bay, making sure that the drive carrier handle is completely closed. Enterprise level hard disk drives are recommended for use in Inaxsys servers. 5-5 Front Bezel The 2U Server supports a full-face locking front bezel for added security.

17 Rack Installation 6-1 Overview This chapter provides a quick setup checklist to get your server up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time. 6-2 Unpacking the System You should inspect the box the server was shipped in and note if it was damaged in any way. If the server itself shows damage you should file a damage claim with the carrier who delivered it. Decide on a suitable location for the rack unit that will hold your server. It should be situated in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and electromagnetic fields are generated. You will also need it placed near a grounded power outlet. Be sure to read the Rack and Server Precautions in the next section. 6-3 Preparing for Setup The box your server was shipped in should include two sets of rail assemblies, two rail mounting brackets and the mounting screws you will need to install the system into the rack. Please read this section in its entirety before you begin the installation procedure outlined in the sections that follow. Choosing a Setup Location Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches). Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing. This product is for installation only in a Restricted Access Location (dedicated equipment rooms, service closets and the like). Rack Precautions Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. In single rack installation, stabilizers should be attached to the rack. In multiple rack installations, the racks should be coupled together. Always make sure the rack is stable before extending a component from the rack. You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.

18 General Server Precautions Review the electrical and general safety precautions that came with the components you are adding to your server. Determine the placement of each component in the rack before you install the rails. Install the heaviest server components on the bottom of the rack first, and then work up. Use a regulating uninterruptible power supply (UPS) to protect the server from power surges, voltage spikes and to keep your system operating in case of a power failure. Allow the hot plug hard drives and power supply modules to cool before touching them. Always keep the rack's front door and all panels and components on the servers closed when not servicing to maintain proper cooling. Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer s maximum rated ambient temperature (Tmra). Reduced Airflow Equipment should be mounted into a rack so that the amount of airflow required for safe operation is not compromised. Mechanical Loading Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading. Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. Reliable Ground A reliable ground must be maintained at all times. To ensure this, the rack itself should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power strips, etc.).

19 To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. 6-4 Rack Mounting Instructions This section provides information on installing the 2U Server into a rack unit with the quick-release rails provided. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly. You should also refer to the installation instructions that came with the rack unit you are using. NOTE: This rail will fit a rack between 26" and 33.5" deep. Separating the Sections of the Rack Rails The server package includes two rail assemblies in the rack mounting kit. Each assembly consists of two sections: an inner fixed server rail that secures directly to the server and an outer fixed rack rail that secures directly to the rack itself. Rail Assembly Separating the Inner and Outer Rails 1. Locate the rail assembly in the server packaging. Extending the Rails 2. Extend the rail assembly by pulling it outward. Quick-Release Tab 3. Press the quick-release tab Separating the Inner Rail Extension 4. Separate the inner rail extension from the outer rail assembly.

20 Warning: do not pick up the server by the front handles. They are designed to pull the system from a rack only. Installing the Inner Rail Extension The 2U Server includes a set of inner rails in two sections: inner rails and inner rail extensions. The inner rails are pre-attached to the server, and do not interfere with normal use of the server if you decide not to use a server rack. The inner rail extension is attached to the inner rail to mount the server in the rack. Installing the Inner Rails 1. Place the inner rail extensions on the side of the server aligning the hooks of the server with the rail extension holes. Make sure the extension faces "outward" just like the pre-attached inner rail. 2. Slide the extension toward the front of the server. 3. Optional: Secure the server with 2 screws as illustrated. Repeat steps for the other inner rail extension. Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

21 Outer Rack Rails Outer rails attach to the rack and hold the server in place. The outer rails for the 2U Server extend between 30 inches and 33 inches. Installing the Outer Rails to the Rack 1. Secure the back end of the outer rail to the rack, using the screws provided. 2. Press the button where the two outer rails are joined to retract the smaller outer rail. 3. Hang the hooks of the rails onto the rack holes and if desired, use screws to secure the front of the outer rail onto the rack. 4. Repeat steps 1-3 for the remaining outer rail.

22 Note: figures are for illustrative purposes only. Always install servers into racks from the bottom up. Installing the Server into a Rack 1. Extend the outer rails as illustrated above. 2. Align the inner rails of the server with the outer rails on the rack. 3. Slide the inner rails into the outer rails, keeping the pressure even on both sides. When the server has been pushed completely into the rack, it should click into the locked position. 4. Optional screws may be used to secure and to hold the front of the server to the rack.

23 Appendix A 2U Server Power Supply Specifications This appendix lists power supply specifications for your server system. 2U Server 560W 600W R700W (Redundant) MFR Part # PWS-561-1H20 PWS-605P-1H PWS-702A-IR Rated AC Voltage V 50-60Hz Amp V 60-50Hz 10-4 Amp AC Input V, Hz, 7.5 Amp max --- DC Input Voltage DC Output V standby 3 Amp 3 Amp 4 Amp +12V 43.6 Amp 49 Amp 57 Amp +5V 25 Amp 18 Amp 24 Amp +3.3V 21 Amp 15 Amp 21 Amp -12V 0.6 Amp Amp

24 710W DC-DC Power Supply 2U Server R720W (Redundant) 740W MFR Part # PWS-711-1R PWS-721P-1R PWS-741P-1R Rated AC V, Hz Voltage Amp AC Input V, Hz, 4-9 Amp --- DC Input Voltage Voltage Range = -36V to -75V (24A - 11A) Nominal Voltage = -48V DC Output V standby V +5V standby 4 Amp V 59 Amp V 30 Amp 45 Amp V 20 Amp 24 Amp V 0.6 Amp 0.6 Amp V standby V