LIRA. Architectural Spot and Flood Light INSTALLATION GUIDE

Transcription

1 LIRA TM IG, LIRA, Page 1 / 8

2 CAUTION Do not attempt to install or use Luminaire(s) until you have read and understand this guide and safety labels. Luminaire(s) must be installed by a qualified professional in accordance with all national and local electrical and construction codes and regulations. Ensure that main power supply is OFF before installing or wiring luminaire(s). Do not exceed specified voltage and current input. Do not use luminaire(s) with a damaged lens, body, or cable. Not heeding cautions may result in a hazardous situation which can cause equipment and property damage, personal injury, or death. Do not exceed the specified voltage and current input. Do not exceed the maximum number of specified fixtures in a light run. Doing so will result in a current overload. GVA Luminaires have no serviceable parts. Do not attempt to open the units. Do not hot swap! Ensure power supply is off before connecting or disconnecting fixtures. Do not stare into beam or view directly with optical instruments. Unauthorized feild repairs will void warranty. 1. MOUNTING BRACKET INSTALLATION Use mounting hardware suitable for the mounting surface. Use of innappropriate hardware may result in dismounting of the bracket and can result in equipment damage, personal injury, or death. Install mounting bracket in desired location using either one or two M6 (OR 1/4in) bolts or screws suitable for the mounting surface. See "MOUNTING HOLE TEMPLATE" to mark holes prior to installation, if necessary. MOUNTING HOLE TEMPLATE (1:1 SCALE) REQUIRED HARDWARE: 3 x 6.8mm (.27in) OR 1X 24mm (0.94in) M6 OR 1/4IN BOLT OR SCREW (not supplied) 29.2mm (1.15in) IF USING MOUNTING SURFACE: IF USING LANDSCAPE SPIKE: M6 (OR 1/4in) BOLT OR SCREW (supplied by others; 1 in the center or 1 per slot) THUMB SCREW LIRA BRACKET LIRA BRACKET LIRA LANDSCAPE SPIKE GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 2 / 8

3 LIRA SNOOT 2. INSTALLATION Using the provided hardware, install LIRA snoot to luminaire as shown. If not installing LIRA snoot skip to Step 3. NOTE: This is a custom configuration. Please contact factory for details. REQUIRED HARDWARE: LIRA GEN.2 OPTICAL ACCESSORY 4X M3x0.5x5MM FLATHEAD SCREW 4 X M3 SCREW NOTE: APPLY LOCTITE 271 (not supplied) PRIOR TO INSTALL NOTE: TORQUE SCREWS TO 1NM LUMINAIRE INSTALLATION 3. (WITH LIRA VISOR) Using the provided hardware, install the LIRA luminaire as shown. If installing the LIRA visor, do so in conjunction with the luminaire installation as shown. Diagram 3.A. Luminaire with Visor Diagram 3.B. Luminaire without Visor REQUIRED HARDWARE: REQUIRED HARDWARE: M6 DISCLOCK WASHER M6X1X10MM SCREW M6 DISCLOCK WASHER M6X1X8MM SCREW LIRA VISOR OR LIRA SNOOT M6 DISCLOCK WASHER M6 DISCLOCK WASHER M6X1X10MM SCREW M6X1X8MM SCREW GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 3 / 8

4 4. WIRING DIAGRAM: OVERALL SYSTEM DIAGRAM Ensure power supply is turned OFF before making any connections. Connecting the luminaire while the power is turned ON may result in equipment damage. Make connections to junction boxes and to the luminaires. NOTE: LIRA luminaire 12 or 24VDC power conductors should be connected in parallel. DMX Common to be also connected in parallel. NOTE: DMX I/O must be connected in series. NOTE: Total load shall not exceed power rating of PDB-ELV/PS-ELV and should be under 100W to remain Class 2. NOTE: Follow labels & markings on terminal blocks & cables for correct polarity. TYPICAL SYSTEM DIAGRAM: NOTE: Luminaire configuration and length of leader cables and jumper cables directly affects the maximum number of luminaires allowed in a single run. LINE VOLTAGE AC INPUT PDB-ELV or PS-ELV AC OUTPUT CABLE (optional, supplied by others) DMX INPUT CABLE (for DMX luminaire only) DATA OUTPUT CABLE (optional, supplied by others) (for DMX luminaires only) DAISY CHAIN SYSTEM FIRST 7C POWER & DMX CABLE (or 2C power cable & 5C DMX cable) (for DMX luminaires) OR 2C POWER CABLE (for non-dimming luminaires) LAST 7C POWER & DMX CABLE (or 2C power cable & 5C DMX cable) (for DMX luminaires) OR 2C POWER CABLE (for non-dimming luminaires) LEADER CABLE LIRA LUMINAIRE LEADER CABLE LIRA LUMINAIRE RADIAL SYSTEM 7C POWER & DMX CABLE (or 2C power cable & 5C DMX cable) (for DMX luminaires) OR 2C POWER CABLE (for non-dimming luminaires) LEADER CABLE LIRA LUMINAIRE(S) GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 4 / 8

5 5. WIRING DIAGRAM: PDB/PS-ELV Ensure that line power is disconnected before making connections to PDB/PS-ELV. For LIRA DMX luminaires refer to Diagram 5.A. for PDB-ELV connections. For LIRA non-dimming luminaires, refer to Diagram 5.B. for PS-ELV connections. Diagram 5.A. PDB-ELV Wiring Diagram AC INPUT 120~277VAC AC OUTPUT 120~277VAC OPTION A (if connecting multiple PDBs) POWER SUPPLY DMX OUTPUT (from DMX luminaires or junction box) DMX OUTPUT (to next PDB; becomes DMX input) DMX INPUT DMX OUTPUT OPTION B (if connecting only one PDB or last in line of PDBs) THIS WAY UP WHEN MOUNTING ON VERTICAL SURFACES DMX I/O TERMINAL VDC & DMX OUTPUT (to DMX luminaires or junction box) VDC OUTPUT TERMINAL NOTE: Terminate return DMX output (+) and (-) with 120 OHM resistor. Diagram 5.B. PS-ELV Wiring Diagram DMX OUTPUT (from DMX luminaires or junction box) 120 OHM RESISTOR AC INPUT 120~277VAC AC OUTPUT 120~277VAC POWER SUPPLY THIS WAY UP WHEN MOUNTING ON VERTICAL SURFACES VDC & DMX OUTPUT (to non-dimming luminaires or junction box) VDC OUTPUT TERMINAL GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 5 / 8

6 6. WIRING DIAGRAM: JUNCTIONS BOXES Ensure power supply is turned OFF before making any connections. Connecting the luminaire while the power is turned ON may result in equipment damage. Diagram 6.A. Junction Box Wiring Diagram: Daisy Chain NOTE: Diagram shows 2C power cable & 5C DMX cable option, for non-dimming luminaires make only 2C ((+)-red, (-)-black) connections. FIRST LAST TO NEXT LIRA OR TO NEXT LIRA OR Diagram 6.B. Junction Box Wiring Diagram: Radial NOTE: Diagram shows 2C power cable & 5C DMX cable option, for non-dimming luminaires make only 2C ((+)-red, (-)-black) connection GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 6 / 8

7 7. WIRING DIAGRAM: LUMINAIRES Ensure power supply is turned OFF before making any connections. Connecting the luminaire while the power is turned ON may result in equipment damage. Connect Class 2, 12~24VDC output to power conductors of LIRA luminaire : red(+), black(-). Connect DMX I/O to DMX conductors of LIRA DMX luminaire (output optional). NOTE: LIRA Luminaires require 12VDC or 24VDC Class 2 or limited to 25A Power Supply with Class 2 outputs. If PSU is other than Class 2, provisions must be made to create Class 2 outputs. Diagram 7.A. LIRA DMX Luminaire INPUT/OUTPUT RED = +12 or 24VDC BLACK = -12 or 24VDC ORANGE = DMX (-) INPUT ORANGE/WHITE = DMX (+) INPUT BLUE = DMX (-) OUTPUT BLUE/WHITE = DMX (+) OUTPUT BROWN/WHITE = DMX COMMON Diagram 7.B. LIRA Non-Dimming Luminaire INPUT/OUTPUT RED = +12 or 24VDC BLACK = -12 or 24VDC GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 7 / 8

8 NOTES GVA Lighting Inc. is not responsible for printing or clerical errors. Refer to www. for additional information. IG, LIRA, Page 8 / 8