SIPLUS S7-200 PS 203. Overview

Transcription

1 SIPLUS S7-200 PS 203 Overview Design and functionality of the power supply are optimally adapted to the SIPLUS S7-200 micro PLC Slim design Particularly suitable for low cabinet depths Note: SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme-specific information was added. Dimensional drawings Order No.: 6EP SH31 Technical specifications Page 529 Mar 2008 Siemens ITS

2 SIPLUS S7-200 PS 203 Order number 6AG SH31-2AA0 Order No. based on 6EP SH31 Conformal coating Coating of the printed circuit boards and the electronic components Ambient temperature range C Technical data The technical data of the standard product applies except for the environmental conditions. Ambient conditions Relative humidity %, condensation allowed Biologically active substances Conformity with EN , Class 3B2 mold and fungal spores (except fauna) Chemically active substances Conformity with EN , Class 3C4 incl. salt mist and ISA S71.04 severity level G1; G2; G3; GX 1)2) Mechanically active substances Conformity with EN , Class 3S4 including conductive sand, dust 2) Air pressure (depending on the highest positive hpa ( m) temperature range specified) see ambient temperature range hpa ( m) derating 10 K hpa ( m) Page 530 Mar 2008 derating 20 K Siemens ITS

3 Technical specifications Power supplies, type 3.5 A Order No. 6EP SH31 1) Input 1-phase AC Rated voltage U in rated 120/230 V AC Set via wire jumper Voltage range V/ V Overvoltage strength 2.3 x U in rated, 1.3 ms Mains buffering at I out rated > 20 ms at U in = 187 V Rated line frequency; rated line frequency 50/60 Hz, Hz range Rated current I in rated 1.65/0.95 A Switch-on current limitation (+25 C) < 33 A, < 3 ms (U in = 230 V) Page 531 Mar 2008 Siemens ITS

4 I 2 t Built-in incoming fuse Recommended miniature circuit breaker (IEC 898) in the mains power input < 1.0 A 2 s T 2.5 A/250 V (not accessible) Two-pole miniature circuit breaker, 10 A or higher, Characteristic C or 6 A or higher, Characteristic D Controlled, isolated DC voltage 24 V DC Output Rated voltage U out rated Total tolerance ±5% (typ. ±2%) Static line compensation Approx. ±0.1% Static load compensation Approx. ±0.2% Residual ripple < 150 mv pp (typ. 30 mv pp ) Spikes (bandwidth: 20 MHz) < 240 mv pp (typ. 110 mv pp ) Adjustment range - Status indicator - On/Off behavior No overshoot of U out (soft start) Startup delay/voltage rise < 1 s/typ. 80 ms Rated current I out rated 3.5 A Current range Up to +60 C A Derating - Dynamic overcurrent on Power-up on short-circuit Typ. 5 A for 100 ms Short-circuit during operation Typ. 5 A for 100 ms Page 532 Mar 2008 Siemens ITS

5 Parallel switching for enhanced performance Yes, up to 5 units Efficiency Efficiency at U out rated, I out rated Approx. 84% Power loss at U out rated, I out rated Approx. 16 W Closed-loop control Dyn. line compensation Typ. ±0.3% U out (U in rated ±15%) Dynamic load compensation Typ. ±3% U out (I out : 50/100/50 %) Load step settling time 50 to 100% < 5 ms 100 to 50 % < 5 ms Protection and monitoring Output overvoltage protection Yes, according to EN Current limitation 3.8 A Short-circuit protection Constant current characteristic up to typ.14 V, electronic shutdown below that, automatic restart Sustained short-circuit current rms value < 4 A Overload/short-circuit indicator - Safety Primary/secondary isolation Yes, safety extra low output voltage U out according to EN Page 533 Mar 2008 Siemens ITS

6 Safety class Class I Leakage current < 3.5 ma Safety test Yes CE marking Yes UL/cUL (CSA) approval culus-listed (UL 508, CSA C22.2 No. 142), File E Protection against explosion - FM approval - Marine approval - Degree of protection (EN 60529) IP20 EMC Emitted interference EN Class B Supply harmonics limitation EN Noise immunity EN Operating data Ambient temperature range C with natural convection Transport and storage temperature range C Humidity class Climate class 3K3 according to EN 60721, no condensation Mechanics Connections Supply input L, N, PE One screw terminal each for mm 2 solid/finely stranded Output + 1 screw terminal for mm 2 Page 534 Mar 2008 Siemens ITS

7 Output - 2 screw terminals for mm 2 Dimensions 160 x 80 x 62 (W x H x D) in mm Weight, approx. 0.5 kg Mounting Can be snapped onto standard mounting rail EN x7.5/15, wall mounting Accessories Mounting bracket (6EP AA1) 1) SIPLUS module 6AG SH31-2AA0 for extended temperature range -25 C to +70 C and use under medial load (e.g. chlorine-sulfur atmosphere). Page 535 Mar 2008 Siemens ITS