Surge Protection Solutions. Industrial Market Automation Market OEM Market

Transcription

1 Surge Protection Solutions Industrial Market Automation Market OEM Market

2 ASCO Power Technologies is Combining the Surge Protection solutions of Advanced Protection Technologies, EDCO, Islatrol & Emerson Network Power Keeping Power Clean & Green Think about the challenge of navigating rush-hour traffic, even on a good day. Then imagine the havoc and congestion that power surges, spikes, noise and transients can create, turning your commute into a nightmare. When traffic signaling equipment goes down, it creates a ripple effect. Even when you re up and running again, the unfortunate effects can resonate for hours after an occurrence. ASCO Power Technologies combines 45 years of surge protection leadership in the Industrial, Commercial, ITS and DOT Markets. We understand many of the challenges which surface in your industry and are here to help determine the most cost effective surge protection device which meets spec and your needs. Whether it s highway lighting, traffic signals, controller cabinets, cameras, high speed/commuter rail, dynamic message signs, toll roads, weigh stations and red light/speed enforcement or sophisticated intelligent systems, rest assured that ASCO products deliver the mission-critical protection you need to keep all your sensitive equipment operating as expected. Why put your equipment at risk? Turn to ASCO Surge Protection products for peace of mind. We provide solutions for all your application needs and the foundation for Business-Critical Continuity. We are committed to providing quality products, competitive pricing and reliable customer care. If you have any product application or pricing questions, please call us at We look forward to hearing from you. We re here to help!

3 Table of Contents AC POWER SPDS TYPE 1 & TYPE 2 ASCO Model 420 (APT SPDEE Series) ASCO Model 420DC (APT SPDEE DC Series) ASCO Model 425 (APT XCS Series) ASCO Model 430 (APT XDS Series) ASCO Model 460 (APT XAS Series) ASCO Model 465 (APT XAL Series) ASCO Model 480 (APT XBS Series) AC POWER SPDS TYPE 2 ASCO Model 457 (APT XGA Series) ASCO Model 340 (APT G Series) ASCO Model 331 (Edco EMC-240B) AC POWER SPDS - SERIES CONNECTED ASCO Model 256 (Edco SHA-1235FS) ASCO Model 252 (Edco HSP Series) ASCO Model 251 (Edco SHP Series) ASCO Model 258 (Edco SHA-1250) ASCO Model 256 (Edco ACP-340LED / 540LED) COMPONENT ASSEMBLY SPDS TYPE 1 & TYPE 2 ASCO Model 450 (APT XRS Series) ASCO Model 451 (APT XRL Series) ASCO Model 452 (APT XWS Series) ASCO Model 453 (APT XWL Series) DIN RAIL SPDS ASCO Model 318 (APT Din-Rail D Series AC) ASCO Model 318 (APT Din-Rail D Series Photovoltaic DC) ASCO Model 107 & 108 (APT Din-Rail D60) ASCO Model 310 (Edco DRS Din-Rail AC) ASCO Model 105 (Edco DRS Din-Rail DC) AC POWER FILTER / SPDS SERIES CONNECTED ASCO Model 277 (Islatrol IE Series) ASCO Model 275 (Islatrol IC+/LRIC+ Series) DATA / SIGNAL SPDS ASCO Model 265 (Edco SLAC Series) ASCO Model 157 (Edco SS64 & SS65 Series) ASCO Model 175 (Edco PC642 Series ASCO Model 151 (Edco FAS-1 & FAS-2 Series) ASCO Model 172 (Edco PHC Series) ASCO Model 159 (Edco HVCP-48 Series) ASCO Model 160 (Edco CX Series) APT BNCA10kA ASCO Model 166 (Edco CX-HFN Series) ASCO Model 185 (Edco CAT6-POE Series) ASCO Model 184 (Edco CAT6-5POE) ASCO Model 138 (Edco RJA-45 & RJD-45) HIGHWAY LIGHTING ASCO Model 235 (Edco SHA Series) ASCO Model 235 (Edco SHAS Series) MEDIUM VOLTAGE ASCO Model 950 (APT MVF Series)

4 What Electrical System Is It? Based on secondary side of upstream transformer, NOT by how load is connected. Most SPD/TVSS order errors are misunderstandings related to grounding or neutrals. Grounded system means that the system is referenced to ground, NOT that there is a safety ground. By convention, ground wires are not counted as one of the wires (3-wire, 4-wire, etc.). 3-phase 4-wire Grounded Wye Neutral bonded to ground. Neutral pulled into facility. Common system configuration V = 120V (208Y/120V) ASCO 2 V = 277V (48OY/277V) ASCO 4 V = 347V (600Y/347V) ASCO 8 V = 127V (220Y/127V) ASCO 21 (non-usa) V = 220V (38OY/220V) ASCO 7 (non-usa) A G N C phase 4-wire Grounded Wye V B 3-phase 4-wire Grounded Wye Neutral bonded to ground. Neutral NOT pulled into facility. Common system configurations at MCC, pumping and water treatment. V = 120V (208Y/120V) APT 2 V = 277V (48OY/277V) APT 4 V = 347V (600Y/347V) APT 8 V = 127V (220Y/127V) APT 21 (non-usa) V = 220V (38OY/220V) APT 7 (non-usa) A G N C 3-phase 4-wire Grounded Wye V B Resistive or Impedance Grounded Wye 3-phase 4-wire Ungrounded Wye Neutral bonded to ground via grounding resistor. Neutral may, or may not, be pulled into facility. Becoming popular system on high-tech applications. V = 120V (208Y/120V) ASCO 2 V = 277V (48OY/277V) ASCO 4 V = 347V (600Y/347V) ASCO 8 V = 127V (220Y/127V) ASCO 21 (non-usa) V = 220V (38OY/220V) ASCO 7 (non-usa) B A R V G C Resistive or Impedance Groun Neutral NOT bonded to ground. Neutral mayor may not be pulled into facility. Rare system configuration; Error/miss-wire?. Note NEC 285.3(2). V = 120V (208Y/120V) Rare - Call ASCO V = 277V (48OY/277V) ASCO 5 V = 347V (600Y/347V) ASCO 9 V = 127V (220Y/127V) Call ASCO (non-usa) V = 220V (38OY/220V) Call ASCO (non-usa) A G C N V B Split-Phase Single-Phase Single-Phase Neutral bonded to ground. Neutral usually pulled into facility. Very, very Common. V = 120V (120/240V) ASCO 1 V = 240V (240/48OV) Rare - Call ASCO V = 127V (127/254V) ASCO 15 (non-usa) Hi-Leg Grounded Delta Neutral bonded to ground. Neutral often pulled into facility. Common system configuration. V = 120/240V ASCO 3 V = 240/48OV Call ASCO 3-phase 3-wire Corner Grounded Delta System has reference to ground because B phase is grounded. V = 240V ASCO 61 V = 48OV ASCO 51 V = 600V ASCO 91 Note NEC 285.3(2) Occasionally seen at industrial facilities. Normally, this is not used on new construction. G A N B Split-Phase Single-Phase C B N G Hi-Leg Grounded Delta G V B A 3-phase 3-wire Corner C V A V Verify where neutral and ground are! Often this is used for one leg or one piece of equipment. Neutral is bonded to ground. This configuration is used less commonly than perceived (see split-phase ). V = 120V ASCO 11 V = 240V ASCO 12 V = 277V ASCO 16 V = 48OV ASCO 17 Call ASCO V = 127V ASCO 13 (non-usa) V = 220V ASCO 12 (non-usa) 3-phase 3-wire Ungrounded Delta System has NO reference to ground. L-L voltages fixed by transformer, but L-G voltages can vary. V This configuration is known to become unstable. V = 240V ASCO 6 V = 48OV ASCO 5 B V = 600V ASCO 9 Note NEC 285.3(2) G Common system configuration at older industrial facilities. Normally, this is not used on new construction. Open Delta 3-phase 3 or 4-wire. Could be ungrounded, corner grounded or Hi-leg. Very rare, tend to be rural. Various solutions. Call ASCO for information. V G A N A A V C 4 B C

5 SPD Sizing Chart Model 460 (APT XAS) Model 430 (APT XDS) Model 425 (APT XCS) Model 420 (APT SPDEE) Service Entrance Greater than 2000A Exposure Level High Exposure Medium Exposure Low Exposure Lowest Exposure ka per phase 300 ka 200 ka 150 ka 100 ka Model Model 460 (APT XAS) Model 460 (APT XAS) Model 460 (APT XAS) Model 430 (APT XDS) Service Entrance 1200A A Exposure Level High Exposure Medium Exposure Low Exposure Lowest Exposure ka per phase 250 ka 200 ka 150 ka 100 ka Model Model 460 (APT XAS) Model 460 (APT XAS) Model 430 (APT XDS) Model 425 (APT XCS) Service Entrance 800A A Exposure Level High Exposure Medium Exposure Low Exposure Lowest Exposure ka per phase 200 ka 150 ka 100 ka 50 ka Model Model 430 (APT XDS) Model 430 (APT XDS) Model 425 (APT XCS) Model 420 (APT SPDEE) Distribution/Branch Panel 800A A Exposure Level High Exposure Medium Exposure Low Exposure Lowest Exposure ka per phase 200 ka 150 ka 100 ka 50 ka Model Model 430 (APT XDS) Model 430 (APT XDS) Model 425 (APT XCS) Model 420 (APT SPDEE) Distribution/Branch Panel Less than 800A Exposure Level High Exposure Medium Exposure Low Exposure Lowest Exposure ka per phase 150 ka 100 ka 100 ka 50 ka Model Model 430 (APT XDS) Model 430 (APT XDS) Model 425 (APT XCS) Model 420 (APT SPDEE) PRICING & PRODUCT INFORMATION Call

6 AC Power SPDs Type 1 & Type 2 Model 420 (APT SPDEE Series) UL 1449 Fourth Edition Listed 50kA 8 x 20µs All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 200kA SCCR (most models) All UL-required OCP & Safety Coordination Included Inside Voltage Specific Design: Performs better than one-size fits all Tri-Mount Installation for more mounting flexibility: Same unit mounts on Pipe Nipple, Bracket or DIN-Rail Visual Diagnostics: Easy to See; Easy to Understand Performance Specifications 50kA 8 x 20µs Per Mode UL 1449 tested Inominal: 20kA (highest available) UL 1449 tested SCCR: 200kA (most models) Large-Block, 34mm square, 50kA MOVs Individually Fused & Thermally Protected MOVs UL 1449 Voltage Protection Ratings (VPRs): 600V for 120V, 120/240, 208Y/ V for 277V, 480Y/277V Repetitive Impulse: kA - 8 x 20µs; kA - 8 x 20µs Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Peak Operating Temperature: +85 C (185 F) Typical Operating Temperature: -40 C (-40 F) to +60 C (140 F) Response Time: < 1 nanosecond Solid State Bi-directional Operation NEMA 4X Polycarbonate Enclosure UL746C(f1), UL 94-5VA Pre-wired with 3 (1m) of #10 AWG conductor Typical Type 2 Connection: #10 AWG to 30A breaker Dimensions 3/ [29.21] [32.05] Weight:1.60 lbs (0.73 kg) Sized for std 35mm Din-Rail 3.38 [85.95] 4.12 [104.66] 3.24 [82.20] 3.25 [82.55] 3.30 [83.74] 3.58 [90.97] Green = Go Visual Diagnostic Monitoring Green LED = A-OK, Out = replace LED Visible from Multiple Sides & Angles - Better Viewing Every MOV is Monitored as opposed to power is present Tri-Mount Installation Std. 3/4-14 Nipple Options DIN-Rail Mount (rail not incl.) N-G protection Dry Contacts & Audible Alarm Dry Contact connection leads exit through nipple via #18 AWG Other configurations available for OEM - Call Quality, Standards & Validation Bracket Mount for flat surfaces 10 year warranty (longer optional) UL th Edition file: VZCA.E at cul Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA 22.2 No ANSI/IEEE C , C , C , C and C NEMA LS-1 IEC 61643, CE Burn-In tested prior to shipment ISO 9001:2008 Certified Quality Management System ISO 17025:2005 Certified Test Lab RoHS-compliant 6

7 DC Power SPD Type 1 & Type 2 Model 420 DC (APT SPDEE DC Series) UL Listed to UL 1449 Photovoltaic Standard (VZCA.E & VZCA7. E321351) UL Listed as opposed to Recognized - avoids scrutiny over Technical Considerations of Recognized products Avoids Certification Surprises No Unexpected Installation Requirements Does not require additional upstream fusing for SPD safety protection 100kA DC Short Circuit Current Rating (SCCR) Fail-Safe operation arc breaking, slide-gate thermal disconnectors built-in Avoids safety challenges and fusing shortcomings of overseas-standard SPDs Listed to UL 1449 as DC SPD for use in PV applications Options & Configurations for OEMs (see back). See AC SPD Model 420 Data Sheet (DS-70117) for AC Voltage models. Performance Specifications 50kA 8 x 20µs Per Mode 300VDC, 600VDC, 1000VDC, 1500VDC & OEM models All modes of protection: DC+ G, DC- G, DC+ DC- UL 1449 tested I n : 20kA UL 1449 tested SCCR: 100kA DC UL 1449 Listed as Type 1 SPD UL 1449 Type 2 optional for cul Mark Large-Block arrestor-grade 34mm square MOVs Individually Fused and Thermally Protected MOVs Repetitive Impulse: kA-8 x 20µs; kA-8 x 20µs Response Time: < 1nanosecond Monitoring Configurations Standard - Low consumption LED; monitors every MOV Illuminates when power is produced Options N - Removes LED and its circuitry P - MOV Microswitch access option (requires R above) Dimensions Same as 420 on previous page Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: DC Operating Temperature: -40 C (-40 F) to +65 C (149 F) (1500VDC: -40 C (-40 F) to +85 C (185 F)) Solid State Bi-directional Operation NEMA 4X Polycarbonate Enclosure UL746C(f1), UL 94-5VA Pre-wired with 3 (1m) of #8 AWG & #6 AWG ground conductor (1500VDC: #10 AWG) Tri-Mount Installation Std. 3/4-14 Nipple DIN-Rail Mount (rail not incl.) Quality, Standards & Validation 10 year warranty (longer optional) ANSI/IEEE C , C & C Burn-In tested prior to shipment ISO 9001:2008 Certified Quality Management System ISO 17025: Certified Test Lab IEC 61643, CE UL 96A Lightning Protection Master Label 20kA I n Bracket Mount for flat surfaces 7

8 AC Power SPDs Type 1 & Type 2 Model 425 (APT XCS Series) UL 1449 Fourth Edition Listed 100kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCR (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 100kA Per Phase 50kA 50kA 50kA UL 1449 Fourth Edition Listed UL 1449 Fourth Edition Type 1, CSA 22.2 No Optional UL 1449 Fourth Edition Type 2 SPD, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V (data table on back) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz (also 400Hz on <480V) Operating Temperature: -40 C (-40 F) to +85 C (185 F) Weight: 3 lbs (1.4 kg) NEMA 4X Polycarbonate enclosure UL 746C(f1) & UL 94-5VA Dimensions: 8.3 x 3.6 x 3.0 (211mm x 91mm x 77mm) 3/4 threaded hub - weather resistant 4X Pre-wired with 3 (1m) of #10 AWG conductor Typical connection: #10 AWG and 30A breaker Dimensions 8.28 (210.31) 7.41 (188.21) (56.13) (93.22) 3.00 (76.20) 0.19 (4.83) Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For external Mounting on Electrical Distribution Equipment, Switchgear, Switchboards, Motor Control Centers, Panelboards, Transfer Switches, etc. Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Solid State Bidirectional Operation Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Optional: Audible Alarm & Form C Dry Contacts (Contacts rated 240V, 5A; leads are pre-wired through nipple with #18 AWG) Quality, Standards & Validation Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA No UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 8

9 AC Power SPDs Type 1 & Type 2 Model 430 (APT XDS Series) UL 1449 Fourth Edition Listed 100kA 200kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCR (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 100kA Per Phase 50kA 50kA 50kA 150kA Per Phase 100kA 50kA 50kA 200kA Per Phase 100kA 100kA 100kA UL 1449 Fourth Edition Type 1, CSA 22.2 No Optional UL 1449 Fourth Edition Type 2 SPD, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V (data table on back) AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Listing) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Peak Operating Temperature: +85 C (185 F) Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 5 lbs (2.3 kg) NEMA 4X Polycarbonate enclosure UL 746C(f1) & UL 94-5VA Dimensions: 6 x 6 x 4 (152mm x 152mm x 102mm) (excluding removable mounting feet) Lug size: #8 - #10 AWG Typical connection: #8 AWG and 40A breaker Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For external Mounting on Electrical Distribution Equipment, Switchgear, Switchboards, Motor Control Centers, Panelboards, Transfer Switches, etc. Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Solid State Bidirectional Operation Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Optional: Audible Alarm & Form C Dry Contacts (Contact rated 240V, 5A) Quality, Standards & Validation Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA No , UL 1283 UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 9

10 AC Power SPDs Type 1 & Type 2 Model 460 (APT XAS Series) UL 1449 Fourth Edition Listed 100kA 500kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCR (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection 10 Year Warranty (longer optional) Active Surge Monitor (ASM) Available - Contact Factory Performance Specifications Surge Capacities L-N L-G N-G 100kA Per Phase 50kA 50kA 50kA 150kA Per Phase 100kA 50kA 50kA 200kA Per Phase 100kA 100kA 100kA 250kA Per Phase 150kA 100kA 100kA 300kA Per Phase 150kA 150kA 150kA 400kA Per Phase 200kA 200kA 200kA 500kA Per Phase 250kA 250kA 250kA UL 1449 Fourth Edition Listed Type 1, CSA 22.2 No Optional UL 1449 Fourth Edition Type 2 SPD, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V (data table on back) AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Listing) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, 6-digit LCD, w/ test function, reset & no-maint. Eprom memory Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For external Mounting on Electrical Distribution Equipment, Switchgear, Switchboards, Motor Control Centers, Panelboards, Transfer Switches, etc. Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 24 lbs (11 kg) Standard NEMA 1/12/3R/4 enclosure Standard size: 12 x 12 x 7 (305mm x 305mm x 177mm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA No , UL 1283 UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 10

11 AC Power SPDs Type 1 & Type 2 Model 465 (APT XAL Series) Directly Connected, Discrete Protection Elements Between All Possible Modes UL 1449 Fourth Edition Listed 150kA 450kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCR (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection 10 Year Warranty (longer optional) Performance Specifications Directly Connected, Discrete Protection Elements Between All Possible Modes with True 10-Mode Protection Surge Capacities L-N L-G N-G L-L 150kA Per Phase 50kA 50kA 50kA 50kA 300kA Per Phase 100kA 100kA 100kA 100kA 450kA Per Phase 150kA 150kA 150kA 150kA UL 1449 Fourth Edition Listed Type 1, CSA 22.2 No Optional UL 1449 Fourth Edition Type 2 SPD, UL 1283 Listed, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Listing) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For external Mounting on Electrical Distribution Equipment, Switchgear, Switchboards, Motor Control Centers, Panelboards, Transfer Switches, etc. Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 24 lbs (11 kg) Standard NEMA 1/12/3R/4 enclosure Standard size: 12 x 12 x 7 (305mm x 305mm x 177mm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA No , UL 1283 UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 11

12 AC Power SPDs Type 1 & Type 2 Model 480 (APT XBS Series) UL 1449 Fourth Edition Listed 400kA 1,000kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCR (most models) UL 96A Lightning Protection Master Label compliant Rotary Disconnect Switch included as Standard Equipment Dual Redundant Replaceable Modules Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 400kA Per Phase 200kA 200kA 200kA 600kA Per Phase 300kA 300kA 300kA 800kA Per Phase 400kA 400kA 400kA 1000kA Per Phase 500kA 500kA 500kA UL 1449 Fourth Edition Listed Type 1, CSA 22.2 No Optional UL 1449 Fourth Edition Type 2 SPD, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 700V 480Y/277V: as low as 1200V (data table on back) AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Listing) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: toggles Red Service LED, Audible Alarm & Dry Contact (if equipped) N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For external Mounting on Electrical Distribution Equipment, Switchgear, Switchboards, Motor Control Centers, Panelboards, Transfer Switches, etc. Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Dual Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 52 lbs (23.6 kg) Standard NEMA 1/12/3R/4 enclosure Standard size: 20 x 20 x 7.5 (50.8cm x 50.8cm x 19cm) Lug size: #6 - #1/0 AWG Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL 1449 Fourth Edition, CSA 22.2 No Type 2 (Opt.): UL 1449 Fourth Edition, CSA No , UL 1283 UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 12

13 AC Power SPDs Type 2 Model 457 (APT XGA Series) UL 1449 Fourth Edition Listed and CSA 22.2 No kA & 240kA per phase ratings Type 2 SPD All UL required OCP & Safety Coordination included inside Can be installed load-side of main disconnect Replaceable module construction 200kA SCCRs Voltage Specific Highly configurable All MOV suppression elements monitored All Modes of Protection Optional Silicon Avalanche Diode (SAD) Hybrid System 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 160kA Per Phase 80kA 80kA 120kA 240kA Per Phase 120kA 120kA 120kA Silicon Avalanche Diode (SAD) Hybrid (120/240 & 208Y/120): 90kA Per Phase 50kA 40kA 120kA 130kA Per Phase 50kA 80kA 120kA 170kA Per Phase 90kA 80kA 120kA UL 1449 Fourth Edition Listed, UL 1283 Listed & CSA 22.2 No UL 1449 Fourth Edition Type 2 SPD UL 1449 Fourth Edition tested SCCR: 200kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 500V 480Y/277V: as low as 900V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz 200kAIR rated fusing Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring Tri-color Green, Amber, Red LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: toggles Red Service LED, Audible Alarm Redundant monitoring LEDs on modules Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Optional Form C Dry Contacts, 24V, 1A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance SuperCap energy storage device Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs IEC 61643, CE High Energy Parallel Design for Category C-High applications For External Mounting next to Electrical Distribution Equipment, Switchgear, Motor Controls Centers, Panelboards, etc. Individually Fused Suppression Modes Large-Block utility grade 34mm square MOVs Replaceable Phase Module Construction Thermal Sensitivity in Each Mode Busbar Construction Solid State Bidirectional Operation Enclosure-less version for OEM available Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 25 lbs (11.5 kg) Standard NEMA 4 (Other Enclosures Optional) Standard size: 12 x 12 x 7.5 (30.5cm x 30.5cm x 190.5cm) Lug size: #2 - #14 AWG Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 2: UL 1449 Fourth Edition, CSA 22.2 No UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 13

14 AC Power SPDs Type 2 Model 340 (APT G Series) 120 VAC single phase and 120/240 Split Phase UL th Edition Listed Type 2 SPD and CSA 22.2 No Customizable Voltage, Configuration & Labeling Design Including International Voltages & Power Systems Rapid-Ship, Cellular Manufacturing in Florida, USA 160kA - 40kA Per Phase Ratings 20kA Nominal Discharge Current (I-nominal) 100kA SCCRs NEMA 4X Polycarbonate Enclosure UL 96A Lightning Protection Master Label compliant All Modes of Protection Optional Sinewave-Tracking EMI/RFI Filtering Easy Installation Pre-wired 10 AWG Leads (3 feet / 1m), Connect to 20-30A breaker Performance Specifications Surge Capacities L-N L-G N-G 160kA Per Phase 80kA 80kA 80kA 120kA Per Phase 60kA 60kA 60kA 80kA Per Phase 40kA 40kA 40kA 40kA Per Phase (10kA I n ) 20kA 20kA 20kA UL tested I-nominal: 20kA UL tested SCCR: 100kA Response Time: < 1ns Optional Filtering up to -50dB from 10kHz to 100MHz Repetitive Impulse: 5,000 hits Diagnostic Monitoring LED indicator monitoring: Separate L-N and L-G LEDs for each phase Phase Loss monitoring Optional Form C Dry Contacts (Contacts rated 240V, 5A; leads are pre-wired through nipple with 18 AWG) Design & Application Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , IEEE C62.62 and C NEC Article 285 IEC 61643, CE High Energy Parallel Design for IEEE Category C3 & C-High applications, plus Categories B & A For Internal or External Mounting in Process, Automation, Traffic Control, UL 508 Cabinets, Switchgear, etc. Robust 25mm Thermally Protected MOVs Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: Hz Operating Temperature: -40 C (-40 F) to +85 C (185 F) Weight: 3lbs (1.5kg) NEMA 4X Polycarbonate enclosure: UL 746C(f1) & UL 94-5VA 3/4 female threaded hub Quality, Standards & Validation UL 1449 Fourth Edition, CSA 22.2 No Dimensions UL file: VZCA.E at RoHS-compliant 8.28 (210.31) 7.41 (188.21) IEC 61643, CE 5 year warranty (longer optional) (56.13) (93.22) 3.00 (76.20) 0.19 (4.83) Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 14

15 AC Power SPDs Type 2 Model 331 (PowerSure EMC-240B) 120/240 VAC Heavy Duty (Parallel) The ASCO Model 331 surge suppressor is designed to protect AC distribution panel circuits or 120V power supplies feeding sensitive electronic equipment. Electrically, the unit incorporates MOV and thermal fusing technology. Model 331 is designed to be installed in parallel on standard single phase 120/240 VAC (3W + G) or single phase 120 VAC (2W + G) circuits. Fast response time 40 ka per phase capacity Failsafe and fused Operational status indicators ANSI/UL1449 Fourth Edition Type 2 5 year warranty General Technical Specifications Operating Voltage 120/240 VAC Total Peak Surge Current 80 ka (8x20 µs) Short Circuit Current Rating 42 kaic UL1449 Location Type Type 2 UL1449 Nominal Discharge Current (I n ) 3 ka Operating Current NA, Parallel Connection Operating Frequency Hz EMI Attenuation (100 khz to 100 MHz) > 40 db SPD Technology Metal Oxide Varistors (MOVs) Modes of Protection Line-to-Line (L-L), Line-to-Neutral (L-N) Status Indication Power On & MOV s Functional Connection Type Wire Leads Operating Temperature -40 C to +85 C Dimensions (in / mm) 4.6 H x 2.2 W x 2.8 L [ x x mm] Weight (oz / kg) 13.5 oz [0.38 kg] Certifications ANSI/UL1449 Fourth Edition Dimensions [116.84] [71.12] 1/2 [12.7] CHASE NIPPLE Connect on load side of main breakers [54.86] Keep wires short and straight as possible for best suppression performance. Installation Instructions L N 120 V Model 331 L1 240 V L2 N 120 V 120 V Model 331 Ground N L Black Black White Green 120 V applications use a single pole 30 Amp breaker Ground L2 N L1 Black Black White Green 120/240 V applications use a two pole 30 Amp breaker 15

16 AC Power SPDs - Series Connected Model 256 (Edco SHA-1235FS) 120 VAC Single Phase 30A FingerSafe The ASCO Model 256 is a FingerSafe 120VAC single-phase 2W+G, 30A surge suppressor/ filter designed to shunt electrical type transients affecting the electrical distribution inside a traffic cabinet. Model 256 offers 50kA per Mode and 100kA per phase of surge current protection. Model 256 utilizes Thermally-protected Metal Oxide Varistors (TMOVs) with an integrated thermally activated element designed to open in the event of overheating due to the abnormal over-voltage, limited current conditions. 120 VAC, 30A service Multi-stage hybrid design FingerSafe connection Green LED diagnostic indicator (All MOVs monitored incl. N-G) Thermally-protected metal oxide varistors (PTMOVs) 50kA Per Mode and 100kA Per Phase surge current protection Form C Dry Contacts General Technical Specifications Operating Voltage Maximum Operating Current UL tested Maximum Continuous Operating Voltage (MCOV) UL tested Voltage Protection Rating (VPR) UL tested Nominal Discharge Current (I n ) UL tested Short Circuit Current Rating (SCCR) Peak Surge Current Rating Operating Frequency EMI Attenuation SPD Technology Input/Output Terminal Fuse/Breaker Relay Contact Relay Terminal Modes of Protection Operating Temperature Dimensions (in/mm) Weight (lb/kg) Certifications Warranty 120 VAC 30 A 150 V 500 V (L-N, L-G, N-G) 20 ka 65 ka 50 ka/mode, 100 ka/phase 47-63Hz 40 db typ Thermally-protected Metal Oxide Varistors (MOV) w/ L-C Filter Recessed Terminal Screws Finger Safe (20-6AWG) 30A (Max.) Form C Dry Contact (250V, 1A Max.) 3 Position (22-16 AWG) L-N, L-G, N-G -40 C to +85 C H x 3.25 W x 5.75 L [47.6 x 82.6 x mm] 12 oz [ 0.34 kg] UL th Edition Recognized SPD, Type 2 Component Assembly, CSA 22.2, No , UL1283 Recognized Filter 5 years Mounting [47.6] PLCS. [4.8] 3.25 [82.6] PL. [57.2] Installation Diagram [117.5] 5.25 [133.4] 5.75 [146.1] 16

17 AC Power SPDs - Series Connected NF015AN3J0 (Edco HSP-121A) Model 252 (Edco HSP Series) 120 VAC Heavy Duty 120 Volt AC The ASCO Model 252 Series is an advanced three-stage hybrid, solid state power-line protector. such as noise filtering, common mode and normal mode suppression, nanosecond reaction time, power line tracking, and compression screw terminations make the ASCO Model 252 Series an excellent choice in commercial and industrial applications. The ASCO Model 252 Series offers a replaceable fuse designed to remove the load (protected equipment) from the line if the unit is either overloaded or the internal protection fails. This feature prevents surges from entering equipment through a failed protector not noticed by the user NF015AN3N0 (Edco HSP-121BT1RU) Fast response time Failure indicator Power line tracking Filtering Polycarbonate NEMA 4X enclosure (252120NF015AN3J0) Three-stage hybrid design Replaceable fuse 1/2 or 3/4 knockouts for nipple conduit connectors (252120NF015AN3J0) 5 year warranty General Technical Specifications Operating Voltage Clamping Voltage Operating Current Peak Surge Current Operating Frequency EMI Attenuation SPD Technology Modes of Protection Status Indication Connection Type Operating Temperature Dimensions (in / mm) Weight (oz / kg) Certifications Warranty 120 VAC VAC 15 A 39 ka (8 x 20 µs) Hz > 40 db (100 khz to 100 MHz) Metal Oxide Varistors (MOVs) w/ L-C Filter Line-to-Neutral, Line-to-Ground, Neutral-to-Ground Power On & MOVs functional 3 position, 20 A terminal block w/ compression screws Terminals accept up to 14 AWG -40 C to +85 C Exposed Terminal Design: 1.8 H x 2.9 W x 5.3 L [46 x 74 x 135 mm] NEMA 4X: 2.95 H x 4.95 W x 3.0 L [74.93 x x 76.2 mm] NEMA 4X Alternate: 3.1 H x 6.3 W x 3.4 L [78.74 x x mm] 10 oz [0.28 kg] UL 1449 recognized 5 years Dimensions Holes 3/16" [4.76] DIA 1.17" [29.72] 1.17" [29.72] 1.97 [50.04] Holes.17 [4.32] Holes DIA..17" 120 VAC 15 AMPS MAX AC NEUT GRD L I N E E Q UI P LIGHT ON NORMAL LIGHT OFF REQUIRES SERVICE 4.86" [123.44] 5.25" [133.35] AC NEUT GRD NEMA 4X DESIGN Holes 3/16 [4.76] Holes 3/16" DIA. DIA. 3/4" 3/4 Conduit [19.05] Fitting Conduit Fitting 3/4" 3/4 Conduit [19.05] Fitting Conduit Fitting 3/4 [19.05] Conduit 3/4" Conduit Fitting 1/2 [12.7] 1/2 [12.7] 1/2" Conduit Fitting Conduit Fitting 1/2" Conduit Fitting Conduit Fitting [148.08] [159.51] 2.95" [74.93] EXPOSED TERMINAL DESIGN MODEL /2 [12.7] 1/2 [12.7] [57.15] 1/2" Conduit Fitting Conduit Fitting 1/2" Conduit Fitting Conduit Fitting 2.95 [74.93] [79.50] [107.95] [125.73] NEMA 4X ALTERNATE DESIGN 3/4 [19.05] Conduit 3/4" Conduit Fitting Fitting 17

18 AC Power SPDs - Series Connected Model 251 (Edco SHP Series) Single Phase Filter, 120 VAC or 240 VAC The ASCO Model 251 hybrid design exhibits performance levels unattainable with simple shunt type protectors. The two active clamp stages, large inductor and shunt capacitance effectively halt high rate-of-rise surge waveforms, thus preventing initial voltage overshoot. Flexibility of installation is another design feature of Model 251. The protector first and second stages are electrically separate (line side) for use in jurisdictions that require a line filter between stages. Ordering Information MODEL Former Model Name NF010AN6N0 Edco SHP LF010AN6N0 Edco SHP APPLICATION 120 VAC, 10 A 240 VAC, 10 A In addition, the first stage provides protection from MAIN NEUTRAL to GND as well as MAIN LINE to GND. This is an often overlooked feature which becomes significant in locales where NEUTRAL must be kept separate from earth ground inside the cabinet. Multi-stage hybrid design Nanosecond response time Blocks high energy surges Incorporates series choke 5 year warranty General Technical Specifications Installation Instructions Operating Voltage Clamping Voltage Operating Current Peak Surge Current Operating Frequency 120 VAC or 240 VAC 395 VAC or 650 VAC 10 A 58.5kA (8 x 20 µs) 47-63Hz Connection If Line Filter Is NOT Used Line Filter (optional) Cabinet Power AC Hot EMI Attenuation SPD Technology Modes of Protection Status Indication Connection Type Operation Temperature Dimensions (in/mm) Weight (lb/kg) 70 db typ MOVs w/l-c Filter L-N, L-G, N-G NA 1/4-20 & SS Stud -40 C to +85 C 1.8 H x W x 5.3 L [45.7 x 73.0 x mm] 1 lb [ 0.45 kg] 120 VAC Input CB Neutral Buss Main Line Main Neutral Model Edco SHP 251 Series Line In Line Out Neutral Out } Mounting 3/16 [4.8] Dia. (6 places) PLATE 1.17 [29.7] 1.17 [29.7] [73.025] Earth Ground Earth Ground Protected Power Service (to controller and other sensitive electronics) 1. This product could become excessively hot and rupture in the rare event of power line conditions or surge that exceed its rated operating specification. Appropriate precautions should be exercised. 2. High voltages are present on electrical termination. Unit should be serviced by qualified personnel only [123.2] 5.30 [134.6] 18

19 AC Power SPDs - Series Connected Model 258 (Edco SHA-1250) 120 VAC Single Phase Modular The ASCO Model 258 is an upgraded version of the ASCO Model 254. Model 258 also incorporates two LEDs for failure indication in a modular package (Utilizes 12 pin Beau connector). The hardwire terminal base (ASCO Model SHABA, ordered separately) accommodates all wiring and the protection module is designed for easy replacement. The footprint of the SHABA is the same as Model 254. This makes retrofitting older cabinets easy because internal wire lengths do not have to be adjusted. Model 258 offers remote sensing circuitry output that is a dry relay contact closure suitable to interface with a modem or computer port for polling remotely. With this feature, a central computer could detect a failed Model 258 at the intersection. ACCESSORY SOLD SEPARATELY Model 258 provides excellent noise suppression over a large frequency range. Typical noise attenuation is KHz, KHz and 50 1 MHz. Multi-stage hybrid design 60 db maximum noise filtering Nanosecond response time Incorporates series choke 5 year warranty General Technical Specifications Operating Voltage Clamping Voltage Operating Current Peak Surge Current Operating Frequency EMI Attenuation SPD Technology Modes of Protection Status Indication Connection Type Operation Temperature Dimensions (in/mm) Weight (lb/kg) Ordering Information MODEL Former Model Name NF010AN6N0 Edco SHP ACCESSORY Former Accessory Name SHABA SHA-1250-BASE-A 120 VAC 340VAC 15 A 45kA/Phase, 60kA/Total 47-63Hz 50 db typ TMOVs w/ L-C Filter L-N, L-G, N-G Power On & MOVs Functional 1/4-20 SS Stud base, plug-in module operating -40 C to +85 C 3.5 H x W x L [88.9 x 79.4 x 181 mm] 1.72 lbs [ 0.78 kg] APPLICATION 120 VAC, 10 A Terminal Base Adapter Mounting Pin Out Hole (6 places) 3/16 [4.8] PLATE 6.65 [169] 7.15 [181.7] 3.13 [79.5] Line In 1, 2 Neutral In 11, 12 Ground 3, 4, 9, 10 Line Out 5 Neutral Out 7 Relay NC 8 Relay Com 6 19

20 AC Power SPDs - Series Connected Model 256 (Edco ACP-340LED/540LED) 120 VAC Single Phase/240 VAC Single Phase The ASCO Model 256 is an upgrade to the popular Edco ACP-340, adding a failure indicator as well as remote sensing circuitry. In addition, this unit offers much better lightning protection than the standard Edco ACP-340. OPTION: DIN RAIL KIT AVAILABLE ORDER PART # 11604KIT Ordering Information MODEL Former Model Name LF015AN5N0* Edco ACP-540LED NF015AN5N0* Edco ACP-340LED APPLICATION 240VAC, 15A 120VAC, 15A *Not UL Registered The ASCO Model 256 filtering surge protectors absorb power line noise and switching transients that other suppressors and RFI filters pass through. They can replace the RFI filter when high attenuation of noise above 25 MHz is not required. The ASCO Model 256 utilize Thermally-protected Metal Oxide Varistors (TMOVs) with an integrated thermally activated element designed to open in the event of overheating due to the abnormal over-voltage, limited current conditions. 50 ka/mode & 100 ka/phase surge current protection Thermally-protected Metal Oxide Varistors (TMOVs) Power On and failure LED Remote sensing circuitry 5 year warranty General Technical Specifications Operating Voltage Clamping Voltage Operating Current Peak Surge Current Operating Frequency EMI Attenuation SPD Technology Modes of Protection Status Indication Connection Type Operating Temperature Dimensions (in / mm) Weight (lb / kg) Mounting 120 VAC/240 VAC 395 VAC/775 VAC 15A 50 ka/mode, 100 ka/phase Hz 60 db typ MOVs w/l-c Filter L-N, L-G, N-G Power On & MOVs Functional 1/4-20 Stainless Steel Stud -40 C to +85 C H x 3.25 W x 5.75 L [47.6 x 82.6 x 146 mm] 1 lb [0.45 kg] Installation Instructions 120 / VAC Input Earth Site Variable (option) Main Line Cabinet Power AC Hot Bus Main Neutral Earth ASCO Model 256 Gnd NC C NO To Remote Indication If Needed Line Out Neutral Out Protected Power Source (to controller and other sensitive electronics) Hole (4 places) 3/16" Dia. [4.8] PLATE 2.25" [57.2] 3.25" [82.6] Caution: 1. This product could become excessively hot and rupture in the rare event of power line conditions or surge that exceed its rated operating specification. Appropriate precautions should be exercised. 2. High voltages are present on electrical termination. Unit should be serviced by qualified personnel only. 5.25" [133.4] 5.75" [146.0] 20

21 Component Assembly SPDs Type 1 & Type 2 Model 450 (APT XRS Series) UL 1449 Fourth Edition Recognized 100kA 300kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCRs (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection Display on 28 ribbon cable 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 100kA Per Phase 50kA 50kA 50kA 150kA Per Phase 100kA 50kA 50kA 200kA Per Phase 100kA 100kA 100kA 250kA Per Phase 150kA 100kA 100kA 300kA Per Phase 150kA 150kA 150kA UL th Edition Recognized Type 1 CA, CSA 22.2 No Optional UL th Edition Type 2 CA, UL 1283 Recognized, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Rec.) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Installer-locatable display on 28 cable (Longer lengths available) Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For Mounting Internal to Switchgear, Motor Controls Centers, Panelboards or Control Panels Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 5 lbs (2.3 kg) Standard size: 6.5 x 11 x 4.5 (16.5cm x 29.9cm x 11.4cm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL th Edition, CSA 22.2 No Type 2 (Opt.): UL th Edition, CSA No , UL 1283 Recognized UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 21

22 Component Assembly SPDs Type 1 & Type 2 Model 451 (APT XRL Series) Directly Connected, Discrete Protection Elements Between All Possible Modes UL 1449 Fourth Edition Recognized 150kA - 300kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCRs (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection Display on 28 ribbon cable 10 Year Warranty (longer optional) Performance Specifications Directly Connected, Discrete Protection Elements Between All Possible Modes with True 10-Mode Protection Surge Capacities L-N L-G N-G L-L 150kA Per Phase 50kA 50kA 50kA 50kA 300kA Per Phase 100kA 100kA 100kA 100kA UL th Edition Recognized Type 1 CA, CSA 22.2 No Optional UL th Edition Type 2 CA, UL 1283 Recognized, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Rec.) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Installer-locatable display on 28 cable (Longer lengths available) Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For Mounting Internal to Switchgear, Motor Controls Centers, Panelboards or Control Panels Individually Fused & Thermally Protected MOVs Large-Block, 34mm square, 50kA MOVs Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 5 lbs (2.3 kg) Standard size: 6.5 x 11 x 4.5 (16.5cm x 29.9cm x 11.4cm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL th Edition, CSA 22.2 No Type 2 (Opt.): UL th Edition, CSA No , UL 1283 Recognized UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 22

23 Component Assembly SPDs Type 1 & Type 2 Model 452 (APT XWS Series) UL 1449 Fourth Edition Recognized 300kA 500kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCRs (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection Display on 28 ribbon cable 10 Year Warranty (longer optional) Performance Specifications Surge Capacities L-N L-G N-G 300kA Per Phase 150kA 150kA 150kA 400kA Per Phase 200kA 200kA 200kA 500kA Per Phase 250kA 250kA 250kA UL th Edition Recognized Type 1 CA, CSA 22.2 No Optional UL th Edition Type 2 CA, UL 1283 Recognized, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Rec.) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Installer-locatable display on 28 cable (Longer lengths available) Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For Mounting Internal to Switchgear, Motor Controls Centers, Panelboards or Control Panels Individually Fused & Thermally Protected MOVs Large-Block, 34mm square Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 7 lbs (3.2 kg) Standard size: 9 x 11 x 5.3 (22.9cm x 28.0cm x 13.5cm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL th Edition, CSA 22.2 No Type 2 (Opt.): UL th Edition, CSA No , UL 1283 Recognized UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 23

24 Component Assembly SPDs Type 1 & Type 2 Model 453 (APT XWL Series) Directly Connected, Discrete Protection Elements Between All Possible Modes UL 1449 Fourth Edition Recognized 300kA - 450kA per phase ratings All UL required OCP & Safety Coordination included inside Type 1 SPDs intended for Line or Load Side of Main Disconnect Type 2 SPDs intended for Load Side of Main Disconnect 20kA Inominal (I n ) 200kA SCCRs (most models) UL 96A Lightning Protection Master Label compliant Voltage Specific Design Highly configurable All MOV suppression elements monitored All Modes of Protection Display on 28 ribbon cable 10 Year Warranty (longer optional) Performance Specifications Directly Connected, Discrete Protection Elements Between All Possible Modes with True 10-Mode Protection Surge Capacities L-N L-G N-G L-L 300kA Per Phase 100kA 100kA 100kA 100kA 450kA Per Phase 150kA 150kA 150kA 150kA UL th Edition Recognized Type 1 CA, CSA 22.2 No Optional UL th Edition Type 2 CA, UL 1283 Recognized, CSA 22.2 No UL 1449 Fourth Edition tested Inominal (I n ): 20kA UL 1449 Fourth Edition tested SCCR: 200kA & 100kA UL 1449 Fourth Edition Voltage Protection Ratings (VPRs): 208Y/120V: as low as 600V 480Y/277V: as low as 1000V AC Sinewave Tracking Filter with EMI/RFI Filtering up to -50dB from 10kHz to 100MHz (Type 2 option only, incl. UL 1283 Rec.) Repetitive Impulse: 5,000 hits Less than 1 nanosecond response time Diagnostic Monitoring 100% monitoring Every MOV is monitored, including N-G Green LED Status indicator per phase Red LED service indicator Audible Alarm with Silence Switch Test Function: Toggles Red Service LED, Audible Alarm & Dry Contact N-G overvoltage detection Phase Loss monitoring (toggles LED & dry contacts) Electrically isolated circuitry ensures surges do not damage diagnostics Form C Dry Contacts, 240V, 5A (two sets) Optional Surge Counter, six-digit LCD, with test function, reset & no-maintenance Eprom memory Installer-locatable display on 28 cable (Longer lengths available) Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , C , C , C , IEEE SA (Emerald Book) NEC Article 285 NEC Articles (E), , 670.6, , & 708 requiring SPDs UL 96A and NFPA 780 Lightning Protection IEC 61643, CE High Energy Parallel Design for Category C-High applications For Mounting Internal to Switchgear, Motor Controls Centers, Panelboards or Control Panels Individually Fused & Thermally Protected MOVs Large-Block, 34mm square Replaceable Module Construction Solid State Bidirectional Operation Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -25 C (-15 F) to +60 C (140 F) Weight: 7 lbs (3.2 kg) Standard size: 9 x 11 x 5.3 (22.9cm x 28.0cm x 13.5cm) Lug size: #2 - #14 AWG (w/opt. disconnect: #6 - #1/0) Typical connection: #6 AWG and 60A breaker Quality, Standards & Validation Type 1: UL th Edition, CSA 22.2 No Type 2 (Opt.): UL th Edition, CSA No , UL 1283 Recognized UL file: VZCA.E at RoHS-compliant Burn-In tested prior to shipment ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 24

25 DIN-Rail SPDs Model 318 (APT AC Power DIN-Rail) Type 1 Component Assembly Intended for use in Type 1 or Type 2 Applications UL 1449 Fourth Edition Recognized Type 1 Component Assembly Parallel Electrical Connection Easy to install 50kA per mode All UL required OCP & Safety Coordination included inside Supplemental Fusing/OCP Not Required UL 1449 Fourth Edition: 20kA Inominal UL 1449 Fourth Edition: 200kA SCCRs Large-Block 34mm sq. MOVs Individually Fused & Thermally Protected Diagnostic Monitoring - Visual Indicator Tabs Optional Form C Normally Open/Closed Dry Contact Performance Data Model Physical Specifications System Voltage & Configuration Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -40 C (-40 F) to +85 C (185 F) Polymeric Enclosure: Flame rated UL94 V-0 Weight: 0.25 lbs (114 kg) per pole Wire Lug Size: #6 - #14 AWG # of Poles UL 1449 VPR (6kV - 3kA) I n SCCR MCOV NP05A1FN10 (D120V1P) 120V kA 200kA SP05A2FN10 (D120V2P) 120/240V kA 200kA YP05A3FN10 (D120V3P) 208Y/120V kA 200kA YP05N4FN10 (D120V3PNG) 208Y/120V w/n-g kA 200kA NP05A1FN10 (D127V1P) 127V kA 200kA SP05A2FN10 (D127V2P) 127/254V kA 200kA YP05A3FN10 (D127V3P) 220Y/127V kA 200kA YP05N4FN10 (D127V3PNG) 220Y/127V w/n-g kA 200kA NP05A1FN10 (D230V1P) 230V kA 200kA SP05A2FN10 (D230V2P) 230/460V kA 200kA DP05A3FN10 (D240V3PD) 240V Delta kA 200kA DP05G3FN10 (D240V3PDG) 240V Delta kA 200kA NP05A1FN10 (D277V1P) 277V kA 200kA YP05A3FN10 (D277V3P) 480Y/277V kA 200kA YP05N4FN10 (D277V3PNG) 480Y/277V w/n-g kA 200kA YP05A3FN10 (D347V3P) 600Y/347V kA 200kA YP05N4FN10 (D347V3PNG) 600Y/347V w/n-g kA 200kA DP05A3FN10 (D480V3PD) 480V Delta kA 200kA DP05G3FN10 (D480V3PDG) 480V Delta kA 200kA 550 Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , and C NEC Article 285 IEC , CE High Energy Parallel Design for Category C-High applications For Internal mounting within control panels, medical, telecom, drives, security systems, robotics, etc. Less than 1 nanosecond response time Repetitive Impulse: 5,000 hits Solid State Bidirectional Operation Optional Dry Contact M Suffix Option Form C: Normally Open or Normally Closed Contact Wire Size: #16 - #30 AWG, Torque: 2.0 lb-in Contact Rating: 125Vac, 3A maximum NO COMMON NC Quality, Standards & Validation UL 1449 Fourth Edition Recognized, cul UL file: VZCA2.E at RoHS-compliant 5 year warranty (longer optional) ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification 125Vac 3A max 25

26 DIN-Rail SPDs Model 318 (APT DC PV DIN-Rail) Type 1 Component Assembly Intended for use in Type 1 or Type 2 Applications UL 1449 Fourth Edition Recognized Type 1 Component Assembly Parallel Electrical Connection Easy to install 50kA per mode All UL required OCP & Safety Coordination included inside Supplemental Fusing/OCP Not Required UL : 20kA Inominal UL : 200kA SCCRs Large-Block 34mm sq. MOVs Individually Fused & Thermally Protected Diagnostic Monitoring - Visual Indicator Tabs Optional Form C Normally Open/Closed Dry Contact Performance Data Photovoltaic DC Model System Voltage & Configuration # of Poles UL 1449 VPR (6kV - 3kA) I n SCCR MCOV 318D600P05A2FN10 (D600VPV) 600VDC kA 10kADC 750VDC 318D600P05A3FN10 (D600VYPV) 600VDC kA 10kADC 720VDC 318D10XP05A3FN10 (D1000VPV) 1000VDC kA 10kADC 1250VDC 318D10XP05A3FN10 (D1000VYPV) 1000VDC kA 10kADC 1250VDC (PV DC models are URus. Canadian PV SPD standards not yet established.) Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Frequency: 47-63Hz Operating Temperature: -40 C (-40 F) to +85 C (185 F) Polymeric Enclosure: Flame rated UL94 V-0 Weight: 0.25 lbs (114 kg) per pole Wire Lug Size: #6 - #14 AWG Quality, Standards & Validation UL 1449 Fourth Edition Recognized, cul UL file: VZCA2.E at RoHS-compliant 5 year warranty (longer optional) ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification Design Attributes Designed, Manufactured & Tested consistent with: ANSI/IEEE C , C , and C NEC Article 285 IEC , CE High Energy Parallel Design for Category C-High applications For Internal mounting within control panels, medical, telecom, drives, security systems, robotics, etc. Less than 1 nanosecond response time Repetitive Impulse: 5,000 hits Solid State Bidirectional Operation Optional Dry Contact M Suffix Option Form C: Normally Open or Normally Closed Contact Wire Size: #16 - #30 AWG Torque: 2.0 lb-in Contact Rating: 125Vac, 3A maximum NO COMMON NC Vac 3A max 26

27 DIN-Rail SPDs Model 107 / 108 (APT D60401-S and -B) Low Voltage DIN Rail, Series-Connected The ASCO Model 107 & 108 SPDs are intended for use on a wide range of low voltage applications inside appropriate enclosures, including high speed communication circuits. Terminals are finger-safe. Model 107 Model 107 is offered for Analog, DC voltage or low-frequency data to 600kHz. Model 108 is offered for digital or high-frequency data up to 35MHz. UL 96A Lightning Protection Master Label Thermal Protection Three stage surge suppression General Technical Specifications Surge Current Rating 15kA Rated Operating Current IL (ma) Model 107 = 800mA, Model 108 = 1000mA IEC Max. Discharge Current I max 15kA IEC Max. Discharge Current I n 10kA IEC Max. Lightning Pulse Iimp (10x350µs) 2.5kA Number of Wires Protected Up to 4 wires (2 pair) Wire Size 14 AWG - 26 AWG Response Time (ns) <1 ns Temperature Rating -40 F to 185 F (-40 C to 85 C) Enclosure Material Thermoplastic UL 94-V0 Enclosure NEMA 1 (IP 20) Dimensions (in / mm) Weight (oz / g) Warranty 3.9 x 2.6 x 0.47 [99mm x 65mm x 12mm] 4.75oz [135g] 5 years Voltage Codes Nominal Operating Voltage (VDC / VAC) 5 / / / / / 42 MCOV (VDC) Clamping Voltage (VDC) < 12 < 27 < 46 < 85 < 105 Voltage Breakdown (Min/Max VDC) 7 / 9 16 / / / / 82.5 IEC Voltage Protection Level 1kV/µs, VDC) Maximum Leakage Current (µa) Suggested Applications Protocol Nominal Voltage Suggested SPD RS-232 +/- 25V 107D033S15KXN4D0 (APT D S) RS-423 +/- 6V 107D018S15KXN4D0 (APT D S) RS V - +6V 108D018S15KLN4D0 (APT D B) RS-485-7V V 108D018S15KLN4D0 (APT D B) Modbus (usually RS-485) - 108D018S15KLN4D0 (APT D B) Irrigation/ Sprinkler Valves 24VAC 107D062S15KXN4D0 (APT D S) 4-20mA Need to determine. Could be 24VDC, 12VDC, etc. 107D062S15KXN4D0 (APT D S) Don t Know? Can t Find Out? 107D062S15KXN4D0 (APT D S) Dimensions Product Information Typical 4-Wire Installation 0.47 in. [12 mm] Unprotected Side Install such that surge hits this side Protected Side VALUABLE EQUIPMENT SIDE Finger Safe Terminals 2.56 in. [65 mm] Ground lug tab 3.9 in. [80 mm] Internally connected to DIN-Rail DIN-Rail not included Series connected (Power/Data goes through SPD) Protects up to 4 wires (2 pairs of 2 wires) DIN-Rail not included 27

28 DIN-Rail SPDs Model 310 (ENP DRS Series) Effectively handles high-energy transients on TT, TN-C, TN-S and TN-C-S three-phase power systems SPD rated Type 2 in accordance with EN ; Class I & II in accordance with IEC Built-in thermal components disconnect SPD from the power source to avoid thermal runaway conditions MOV only or MOV+Gas Tube models available Fast response time, high surge current capability, low voltage protection levels Visual inspection window on each module indicates status 3-pole terminal provides remote status monitoring DIN rail mounting and plug-in module design allow for easy installation, maintenance and replacement of surge element Performance Specifications System Voltage Quality, Standards & Validation EN Type 2 IEC : Class II RoHS-compliant 5 year warranty /208, 127/220VAC 230/400, 220/380, 240/415VAC 277/480, 254/440VAC 346/600VAC Nominal Voltage Un 120V Un 230V Un 277V Un 346V Rated Voltage (MCOV) Uc 150V Uc 320V Uc 320V Uc 420V Voltage Protection Level Up 1.2kV Up 1.6kV Up 1.6kV Up 2.0kV Maximum Discharge Current: I max 40 ka Nominal Discharge Current (8 x 20 µs) Modes of Protection Type of Network Response Time Isolation Resistance Physical Specifications Relative Humidity Range: 0-95% non-condensing Operating Temperature: -40 C (-40 F) to +85 C (185 F) NEMA 4X Polycarbonate enclosure: UL 746C(f1) & UL 94-5VA Screw Terminal: 4-25 mm2 By Connection Bus I n 20 ka L-N; N-PE TT-TN TS 25 ns > 103MV Ordering Information 310 XXX Y Z A Formerly DRS Nominal Voltage (U n ) Nominal Voltage (U n ) (XXX) # of Metal Oxide Varistor Modules (Y) MOV Modules are typically one module per phase and may be wired L-N, L-G or N-G. Gas Tube Modules Typically used in the N-G mode for type TT Grounding Systems. Certain applications requre higher rated components in order to survive frequent voltage rises, in this case order a unit with a Q at the end of the part number. Mechanical Specifications # of MOVs # of Gas Tube Modules # of Gas Tube Modules (Z) 0 1 Higher Rated Voltage (A - Optional) Q (Optional) Higher Rated Voltage Dimensions (Length x Width x Height) 70.8mm x 90.5mm x 68mm I/O Connections By Screw Terminal: 4-25 mm2 By Connection Bus MOV Encapsulation Material Epoxy Resin Disconnection Indicator Mechanical Indicator Status Monitoring Remote Alarm Terminals Mounting Symmetrical Rail Operation Temperature Range -40 C to +85 C Degree of Protection IP 20 Disconnection Device Thermal Cutoff System Housing Material ABS/PA UL94V0 28

29 DIN-Rail SPDs Model 105 (Edco DRS Series) DIN Rail Protection The ASCO Model 105 is a din rail mountable, single pair surge suppression module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak currents are mitigated with resetable fuses (PTCs). The PTCs increase resistance several orders of magnitude when over-currents exceed safe levels. A normal state resumes when overcurrents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. The Model 105 mounts onto a standard 35mm industrial din rail. There are three Field Side and three Electronics Side screw terminals. One is reserved for a shield. Three electrically tied ground terminals are provided for grounding the Model 105 unit to Building-Approved Ground. Shield is isolated from ground. Two (2) terminal versions without a shield connection are also available. Low-voltage data surge protection Three-stage hybrid protection Sneak/fault current protection with resettable fuses (PTCs) Low profile packaging Easy installation Fits standard 35mm DIN-Rail General Technical Specifications Operating Voltage 6, 12, 24, 30, 35 VDC Clamping Voltage 8, 15, 30, 36, 43 VDC Operating Current 0.15 A Peak Surge Current 10 ka (8x20µs) Max Current Ip (Occurrences) >100 (10x1000µs) Typical Capacitance 1500pf Nominal Series Resistance 5 Ω Response Time < 1 nanosecond Operating Temperature -40 C to 85 C Certifications UL 497B Warranty 5 years 105D200S08KAN3D0 Special Operating Voltage 170 VDC Clamping Voltage 200 VDC Operating Current 5 Amp Max Current Ip (Occurrences) >10 (10x1000µs) Total Peak Surge Current Rating 8 ka (8x20µs) Nominal Series Resistance None Installation Instructions 3-TERMINAL DEVICE 2.95 [74.9] 2-TERMINAL DEVICE 2.95 [74.9] 1.1 [27.9] 1.1 [27.9] 0.8 [20.3] 0.49 [12.4] 2.35 [59.7] SHIELD 2.35 [59.7] LINE LINE LINE LINE Ground Ground 2.25 [57.2] 2.25 [57.2] Field Side (Line) Protected Equipment Side (Load) Field Side (Line) Protected Equipment Side (Load) These protectors are intended for indoor use on communication loop circuits which have been isolated from the Public Switch Telephone Network. The communication loop circuits shall not be exposed to accidental contact with the electric light or power conductors. The protectors shall be installed per the applicable requirements of the National Electric Code, ANSI/NFPA 70. Ordering Information MODEL Former Model Name 105D008S10KAN3D0 Edco DRS D015S10KAN3D0 Edco DRS D030S10KAN3D0 Edco DRS D036S10KAN3D0 Edco DRS D043S10KAN3D0 Edco DRS D200S08KAN3D0 Edco DRS-130RMS 105xxxxxxxxxN2xx Edco DRS-XXX-2 APPLICATION 0-8 VDC 0-15 VDC 0-30 VDC 0-36 VDC 0-43 VDC VDC 2 Terminal Version without shield 29

30 AC Power Filter / SPDs Series Connected Model 277 (Islatrol IE Series) Active Tracking Filter TM The ASCO Model 277 is a series-connected DIN or flange mounted high frequency noise filter and surge suppressor. Its ideal applications include critical industrial loads drawing up to 20 Amps of continuous current, while typical applications include any microprocessor-based products, including industrial PLCs, OEM applications, and motion control systems. Multi-staged design, combining a unique hybrid clamping network with the active tracking technology of the ASCO family Surge current capacity 45,000 Amps Transient protection in all modes: line to neutral, line to ground, and neutral to ground LED status indication and form C contact for remote indication DIN mountable enclosure ANSI/UL 1449 Fourth Edition Type 4, 1283, CUL recognized, CE 5 year warranty 30 Performance Technical Specifications Model L-N L-G N-G L-L NF003AN3N NF005AN3N0 400V 600V 600V N/A NF010AN3N NF020AN3N0 400V 600V 500V N/A LF003AN3N LF005AN3N0 1000V 700V LF010AN3N LF020AN3N0 900V 700V Peak Surge Current Capability (8 x 20 µs) Line to Neutral 15,000 Amps Line to Ground 15,000 Amps Neutral to Ground 15,000 Amps Total 45,000 Amps Frequency Response (Forward-Reverse) Normal Mode 100 khz to 50 MHz - 90 db Min Common Mode 5 MHz to 50 MHz - 60 db Min Typical Category A Ringwave (6 kv, 200 A, 100 khz) Normal Mode/Common Mode 3 Amp 1V / 300V 5 Amp 0.7V / 292V 10 Amp 0.7V / 300V 20 Amp 0.7V / 300V Typical Category B Ringwave (6 kv, 500 A, 100 khz) Normal Mode/Common Mode 3 Amp 178V / 300V 5 Amp 162V / 291V 10 Amp 153V / 300V 20 Amp 200V / 300V General Technical Specifications MCOV 120 Volt 150 VRMS 240 Volt 275 VRMS Line Frequency Hz Connection Terminal Mounting Type DIN/Flange Weight < 3 lbs Response Time Normal Mode < 0.5 ns Common Mode < 5 ns Operating Temperature -40 C to +45 C Derate Linearly to 60% at +70ºC Operating Humidity 0% to 95% Dimensions Ordering Information MODEL Former Model Name NF003AN3N0 Islatrol IE NF005AN3N0 Islatrol IE NF010AN3N0 Islatrol IE NF020AN3N0 Islatrol IE LF003AN3N0 Islatrol IE LF005AN3N0 Islatrol IE LF010AN3N0 Islatrol IE LF020AN3N0 Islatrol IE-220 VOLTAGE 120V 120V 120V 120V 240V 240V 240V 240V CONTINUOUS CURRENT 3 Amps 5 Amps 10 Amps 20 Amps 3 Amps 5 Amps 10 Amps 20 Amps (All voltage configurations are single phase - 2 wire + gnd.)

31 AC Power Filter / SPDs Series Connected Model 275 (Islatrol IC+/LRIC+ Series) Active Tracking Filter TM Series connected high-frequency noise filter with transient protection. Offers the flexibility of either receptacle/line cord connection or hard-wired connection to critical loads (up to 30 Amperes). Applications include industrial or office equipment, computers placed in harsh environments. Typically reduces normal mode transients to +/-2 volts LED power indication UL 1283, CSA recognized 5 year warranty Surge current capacity 45,000 Amps Transient protection in all modes: line to neutral, line to ground, and neutral to ground Performance Technical Specifications MCOV 120 Volt 150 VRMS 240 Volt 275 VRMS Line Frequency Hz Response Time Normal Mode < 0.5 ns Common Mode < 5 ns Operating Temperature -40 C to +45 C at Full Load Derate Linearly to 60% at +70ºC Operating Humidity 0% to 95% Peak Surge Current Capability (8 x 20 µs) Line to Neutral 15,000 Amps Line to Ground 15,000 Amps Neutral to Ground 15,000 Amps Load Surge Current Rating 10 msec 5 x Nominal 1 sec 3 x Nominal 10 sec 2 x Nominal Packaging High Impact Plastic Case Vacuum Impregnated Magnetics Epoxy Encapsulated Frequency Response (Forward-Reverse) Normal Mode 100 khz to 50 MHz - 90 db Min Common Mode 5 MHz to 50 MHz - 60 db Min Typical Category A Ringwave (6 kv, 200 A, 100 khz) MODEL NORMAL COMMON NF002AN3N0 (IC+102) NF002ALCN0 (LRIC+102) NF005AN3N0 (IC+105) NF005ALCN0 (LRIC+105) NF007AN3N0 (IC+107) NF007ALCN0 (LRIC+107) NF015AN3N0 (IC+115) NF015ALCN0 (LRIC+115) NF030AN3N0 (IC+130) LF002AN3N0 (IC+202) LF005AN3N0 (IC+205) LF007AN3N0 (IC+207) LF015AN3N0 (IC+215) LF030AN3N0 (IC+230) Typical Category B Ringwave (6 kv, 500 A, 100 khz) MODEL NORMAL COMMON NF002AN3N0 (IC+102) NF002ALCN0 (LRIC+102) NF005AN3N0 (IC+105) NF005ALCN0 (LRIC+105) NF007AN3N0 (IC+107) NF007ALCN0 (LRIC+107) NF015AN3N0 (IC+115) NF015ALCN0 (LRIC+115) NF030AN3N0 (IC+130) LF002AN3N0 (IC+202) LF005AN3N0 (IC+205) LF007AN3N0 (IC+207) LF015AN3N0 (IC+215) LF030AN3N0 (IC+230) Note: All measurements in volts. IEEE test results with no AC applied. Normal mode L1-N or L1-L2; Common mode L-G, N-G or L1-G, L2-G. Connection Diagram System Design 31

32 Data / Signal SPDs Model 265 (Edco SLAC Series) AC Power / Signal The ASCO Model 265 suppressor was specifically designed to protect electronic instruments used by the water/wastewater industries. It combines hybrid AC power protection and signal line protection in a NEMA-4X polycarbonate case. The AC power suppressor can supply up to 1875 Watts and has a 15 Amp replaceable fuse to prevent overloading of the protective elements. A Power ON LED provides visual indication that power is applied to instruments. Signal line protection is accomplished by Model 265 available in a variety of voltage clamps. Signal current can be monitored by reading the voltage across the 10 Ohm, 1% resistors (TP1 & TP2 or TP3 & TP4). All leads going to the Model 265 board are terminated by quick disconnect or barrier block connectors to facilitate easy removal for service or replacement. Lightning and surge suppression for AC power and low-voltage signal lines Series hybrid AC suppressor/filter Plug-in protection module 15 Amp replaceable fuse Response time < 5 nanoseconds Test jacks for signal line monitoring Power ON indicator Optional stainless steel or fiberglass enclosure 5 year warranty UL 1449 General Technical Specifications AC Power Protection Operating Voltage 120 VAC, Hz Clamping Voltage 325 VAC Operating Current 15 Amps Max. Peak Surge Current 39 ka (8x20 µs) SPD Technology Three-Stage Series Hybrid Occurrences at 500 Amps < 0.1 db at 10 MHz Parameter Normal Mode (L-N) Common Mode (L-N) (N-G) IEEE 587 CAT A Ring* 172 V 280 V IEEE 587 CAT B Ring* 205 V 280 V Installation Instructions UNPROTECTED (FIELD) SIDE 4/20 ma SIGNAL UNPROTECTED (FIELD) SIDE 120 VAC POWER PROTECTED (EQUIP) SIDE 4/20 ma SIGNAL PROTECTED (EQUIP) SIDE 120 VAC POWER IEEE 587 CAT B Impulse* 330 V 360 V *Measured from zero volts, 90 Phase angle Signal Line Protection Clamping Voltage (customer selected) Volts Operating Current 0.15 A Peak Surge Current 10 ka (8x20 µs) SPD Technology Three-Stage Series Hybrid Series Resistance 5 Ohm (Typical) Signal Line Connections: A. Connect GND Terminal to Local Ground using #12 AWG wire minimum. B. L1 and L2 Connect for Signal Pair #1. C. L3 and L4 Connect for Signal Pair #2. D. Terminals accept #24 - #14 AWG wire, torque to 4 kg-cm. E. S Connection for Cable Shield (If Applicable). AC Power Connections: A. Connect AC Power as Marked on Case using #12 AWG wire minimum (L, N, G). B. Keep 120 VAC Power feed separate from Low Voltage 4/20 ma feed. 32 Optional Enclosure NEMA-4X Stainless Steel or Fiberglass Continuous Hinge Outside Dimensions (in/mm) 10.0 H x 8.0 W x 4.0 D [254 x x mm]

33 Data / Signal SPDs Model 157 (Edco SS64 & SS65 Series) Wastewater/Industrial Applications The ASCO Model 157 suppressors are designed for the water and wastewater industry. These multi-stage hybrid suppressors address over-voltage transients with gas tube and silicon avalanche technology. In addition, sneak and fault currents are mitigated with PTC devices which consist of solid-state resettable fuses. The units are encapsulated in stainless steel pipe nipples making them suitable for use in severe environments. The ASCO 157D036S10KXW5R0 and 157D036S10KXW5S0 models protect a signal pair and the ASCO 157D036S10KXW6M0 and 157D036S10KXW6P0 models protect a signal pair plus the cable shield (drain wire). General Technical Specifications Operating Voltage Maximum Continuous Operating Voltage (MCOV) Clamping Voltage (L-G) Clamping Voltage (L-L) Peak Surge Current SPD Technology Frequency Range Insertion Loss Series Resistance (per Conductor) Capacitance (Zero Volts Bias) Operating Temperature 28 VDC 150 ma 36 VDC 72 VDC 10 ka (8x20 µs) GDT, SAD, w/series PTC 0 to 20 MHZ < 0.1 db at 20 MHz 5 Ohm (typical) (L-G) 1200 pf (typical) (L-L) 600 pf (typical) -40 C to +85 C Life Cycle 500 Amps (10x1000 µs) Weight (lb / kg) 0.35 lbs. [0.16 kg] Certifications UL 497B Transient protection for low-voltage signal lines Sneak/fault current protection Resettable fusing PTCs Differential and common mode protection Typical Applications 157D036S10KXW5R0 157D036S10KXW5S0 Automatic recovery Encapsulated in stainless steel pipe nipples Protection for one pair (Two wires & shield on 3/4 ) 5 year warranty Ordering Information MODEL Former Model Name 157D036S10KXW5R0 Edco SS D036S10KXW5S0 Edco SS D036S10KXW6M0 Edco SS D036S10KXW6P0 Edco SS APPLICATION 1/2 Metal Conduit In-Line 1/2 Metal Conduit Capped 3/4 Metal Conduit In-Line, with Shield 3/4 Metal Conduit Capped, with Shield 157D036S10KXW6M0 157D036S10KXW6P0 33

34 Data / Signal SPDs Model 175 (Edco PC642 Series) Zone/Loop/Data The ASCO Model 175 Series surge suppressor is a two-pair (four-wire) module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance by several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. ACSO PCB1B BASE SOLD SEPARATELY OPTION: DIN RAIL KIT AVAILABLE ORDER PART # PCDIN (Edco 11604KIT-PC) The ASCO Model 175 Series card edge module is gold plated, double sided, and is designed to mate with the ASCO PCB1B gold-plated female terminal connector. When snapped together, the data circuits pass thru the protector in a serial fashion from the four Field Side terminals to the four Electronics Side terminals. Terminals 1 or 10 of the ASCO PCB1B must be attached to Building-Approved Ground per ASCO Technical Bulletin # General Technical Specifications Operating Voltage 5, 12, 24, 30, 36, 48, 250 VDC Clamping Voltage 8, 15, 30, 36, 43, 60, 300 VDC Operating Current 0.15 A Peak Surge Current 10 ka (8 x 20 µs) Frequency Range 0 to 20 MHz Insertion Loss < 0.1 db at 50 MHz SPD Technology GDT, SAD, w/ Series PTC Connection Type Terminal Block, w/ compression lugs Terminals accept up to 10 AWG Operating Temperature -40 C to +85 C Dimensions (in / mm) 2.0 H x 1.0 W x 2.5 L [50.8 x 25.4 x 63.5 mm] (175 + PCB1B Base) Weight (oz / kg) 1 oz [0.03 kg] Certifications UL 497B * 175D300S10KAPCN0 is not UL certified Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 150 milliamperes. Three-stage hybrid protection Sneak/fault current protection Resettable fusing PTCs Low capacitance option Plug-in module Terminal Assignments Unprotected Pair 2 Field Side Unprotected Pair 1 Odd Termi nals { { PCB1B: 1.0 Even Termi nals } Protected Pair 2 Electronics Side 2.125" } Protected Pair 1 Keying Pin Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Specifying The Appropriate Model See Data Sheets: ID & ID Application: RS485, RS422: 175D008S10KLPCN0 (PC642C-008)* RS423, Token Ring: 175D008S10KLPCN0 (PC642C-008)* RS232: 175D020S10KAPCN0 (PC642C-020) * E-Net, 10 Base T: 175D030S10KLPCN0 (PC642C-030)* 4 20 ma: 175D036S10KAPCN0 (PC642C-036)* *All models with PCB1B (PCB1B-WKEY) Fast response time Requires ASCO PCB1B base Order ASCO PTU an invaluable troubleshooting tool 5 year warranty UL 497B Installation Instructions Note: These protectors are intended for Model 175 indoor use on communication loop circuits which have been isolated from the Public Switch Telephone Network. The communication loop circuits shall not be exposed to accidental contact with the electric light or power conductors. PCB1B The protectors shall be installed per the applicable requirements of the National Electric Code, ANSI/NFPA 70. Measure DC operating voltage of system to insure it does not exceed the rating of the selected surge device (5-180 VDC depending on the device). Installation: 1. Turn off power to circuit to be protected prior to installation. 2. Screw mounting base #PCB1B (accessory) in desired location preferably as close to protected equipment as possible and in close proximity to a building approved grounding point using (2) #4 screws. PCB1B may also be DIN rail mounted using optional DIN clip accessory #PCDIN. 3. Attach field side pairs (26-10 AWG) to positions 3/5 and 7/9, attach electronics side pairs (26-10 AWG) to positions 2/4 and 6/8. Attach ground wire (10 AWG) to positions 1 or 10 on base. See Drawing 1. Torque wires to 7 lb-in [0.791 N-m]. 4. Insert 175 module into keyed PCB1B base. See Drawing Apply power to protected circuit.

35 Data / Signal SPDs Model 151 (Edco FAS-1 and FAS-2 Series) One and Two-Pair Signal Line Protection The ASCO Model 151 Series are multi-stage one-pair or two-pair surge suppressors designed for high-exposure applications. These products were specifically designed to meet multiple, low voltage, protection applications in the fire and security industries. Lightning protection for low voltage Data/signal lines Multi stage protection UL497B Certification Common mode and differential protection mode Automatic recovery 5 year warranty General Technical Specifications Installation Instructions Ordering Information Operating Voltage Clamping Voltage Operating Current Peak Surge Current Frequency Range Insertion Loss SPD Technology Connection Type Operating Temperature 15, 24, 36, 52 VDC 18, 33, 43, 60 VDC 2.5 A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz GDT, SAD, w/ Series Inductor Terminal block w/ compression lugs, Terminals accept up to 12 AWG -40 C to +85 C UNPROTECTED OR FIELD SIDE Ground Lug AWG EQ UIP. LINE. MODEL Former Model Name 151D018S10KXN2N0 Edco FAS-1-018HC 151D018S10KXN4N0 Edco FAS-2-018HC 151D033S10KXN2N0 Edco FAS-1-033HC 151D033S10KXN4N0 Edco FAS-2-033HC 151D043S10KXN2N0 Edco FAS-1-043HC APPLICATION 12VDC (single pair) 12VDC (two pair) 24VDC (single pair) 24VDC (two pair) 24VAC (single pair) Dimensions (in / mm) Single-Pair = 1.5 H x 1.5 W x 2.8 L [38.1 x 38.1 x mm] Two-Pair = 2.0 H x 2.0 W x 2.8 L [50.8 x 50.8 x mm] Weight (oz / kg) Single-Pair = 3.5 oz [0.1 kg], Two-Pair = 7 oz [0.2 kg] < 3 151D043S10KXN4N0 Edco FAS-2-043HC 151D060S10KXN2N0* Edco FAS-1-060HC 151D060S10KXN4N0* Edco FAS-2-060HC 24VAC (two pair) 48VDC (single pair) 48VDC (two pair) *Not UL Listed PROTECTED EQUIP. GROUNDING 1st Choice: Use AC Power Ground 2nd Choice: Use Building NOTE: DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. A. Never install data wiring during a lightning storm. B. Disconnect data line before installing the protection module. C. These protectors are intended for indoor use on communication loop circuits which have been isolated from the Public Switch Telephone Network. D. The communication loop circuits shall not be exposed to accidental contact with the electric light or power conductors. The protectors shall be installed per the applicable requirements of the National Electric Code, ANSI/NFPA

36 Data / Signal SPDs Model 172 (Edco PHC Series) Two-Pair Signaling Circuit Protector (Modular) The ASCO Model 172 Series is designed to protect two pairs of wires specifically for alarm and security systems where operating currents can be as high as 5 amps. Electrically, the ASCO Model 172 Series is a rugged series hybrid implementing a staged complement of MOVs, copper wound inductors and Silicon Avalanche Diodes. This design reduces series resistance to 0.2 Ohms per pair. These products are intended to mate with an ASCO PCB1B gold-plated female terminal connector. ASCO Model 172 modules plug into a base assembly (ASCO PCB1B). The base assembly can be mounted to any flat surface and should be located as close as practical to the protected equipment. Terminal 1 and/or terminal 10 should be connected to Building-Approved Ground with 12- or 10-gauge solid wire. ASCO PCB1B BASE SOLD SEPARATELY Three-stage protection Differential protection Common mode protection Plug-in module Automatic recovery Fast response time Continuous current up to 5 Amps UL 497B listed Requires ASCO PCB1B base Order ASCO PTU an invaluable troubleshooting tool 5 year warranty General Technical Specifications Operating Voltage 12, 18, 24, 30, 36, 52, 70, 120 VDC Clamping Voltage 15, 20, 30, 36, 43, 60, 100, 150 VDC Operating Current 5 A Peak Surge Current 10 ka (8 x 20 µs) Frequency Range 0 to 10 MHz Insertion Loss < 0.1 db at 10 MHz SPD Technology MOV, SAD, w/ Series Inductor Connection Type Terminal block w/ compression lugs Terminals accept up to 10 AWG Operating Temperature -40 C to +85 C Dimensions (in / mm) 3.7 H x 1.75 W x L [94 x x mm] (172 + PCB1B Base) Weight (oz / kg) 8 oz [0.23 kg] Certifications UL 497B Applications Part Number 24V Horn, Strobe, Bell 70V Speaker Lines 172D043S10KXPCN0 & PCB1B 172D100S10KXPCN0 & PCB1B Terminal Assignments Odd Terminals Unprotected Pair 2 Field Side Unprotected Pair Dimensions { { 1.0 [25.40] Even Terminals } Protected Pair 2 4 Electronics Side 2 } Protected Pair 1 Keying Pin Ground Terminal 1 or 10 to Building Approved Ground (preferably AC Power safety ground). 2.4" [60.96] 2.125" [53.98] DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. MODEL [58.42] Model [93.98] Ordering Information Other configurations available, please contact factory. MODEL Former Model Name 172D015S10KXPCN0 Edco PHC D020S10KXPCN0 Edco PHC D030S10KXPCN0 Edco PHC D036S10KXPCN0 Edco PHC D043S10KXPCN0 Edco PHC D060S10KXPCN0 Edco PHC D100S10KXPCN0 Edco PHC-SP70 172D150S10KXPCN0 Edco PHC-130RMS OPERATING VOLTAGE CLAMPING VOLTAGE 12 VDC 15 VDC 18 VDC 20 VDC 24 VDC 30 VDC 30 VDC 36 VDC 36 VDC 43 VDC (for Horn, Bell, Strobes) 52 VDC 60 VDC 70 VDC *100 VDC 120 VDC *150 VDC (for 120 V Signal Lines) 36

37 Data / Signal SPDs Model 159 (Edco HVCP-48) Zone/Loop/Data The ASCO Model 159 is a hybrid surge protection product featuring DC power, data and video protection in one package. Each separate circuit is capable of handling highcurrent impulses while tightly clamping transients and allowing critical power and data to be transmitted. Three separate hybrid circuits Balanced transition circuit Ultra low capacitance, low signal loss Rugged gas tube protection Optional DIN rail assembly (sold separately) 5 Year warranty UL 497B General Technical Specifications Wiring Diagram DC Power Protection (VS) Operating Voltage Clamping Voltage Operating Current Peak Surge Current SPD Technology Connection Type High Speed Data Protection (SDIO) Clamping Voltage Operating Current Peak Surge Current SPD Technology Connection Type Video Protection Clamping Voltage Peak Surge Current SPD Technology Connection Type Physical Data Ground Wire (in / mm) Terminal Wire Range Wiring Terminal Torque Wiring Terminal Strip Length (in / mm) Dimensions (in / mm) Material Weight (oz / kg) Mounting Operating Temperature Operating Humidity Certifications Environmental 48 VDC 70 VDC 1 Amp 10 ka GDT, SAD, Series Element 5.08mm Terminal Block Plug 15 VDC 0.15 A 10 ka GDT, SAD, Series Element 5.08mm Terminal Block Plug 2 VDC 10 ka GDT, SAD, Series Element 5.08mm Terminal Block Plug 12 AWG, 36.0 [914.4 mm] Long AWG 4.5 LB in [ mm] 3.3 L x 3.3 W x 1.35 H [83.82 x x mm] High Impact Plastic 12 oz [0.34 kg] Flange mounted, 3.75 mounting hold distance, (0.188 dia.) (2x) DIN-Rail mounting (Optional) -40 C to +74 C 0% to 95% Non-condensing RoHS Compliant Safety UL 497B Listed, Tested to IEC Warranty 5 Year Dimensions Model

38 Data / Signal SPDs 160D006S20KXCXN0 (Edco CX06-M) Model 160 (Edco CX Series) CCTV & Data Applications/Coax The ASCO Model 160 Series Surge Protective Devices (SPDs) implement three-stage hybrid technology. The SPDs address over-voltage transients with a primary Gas Discharge Tube (GDT), and secondary Silicon Avalanche Diode (SAD) components. Over-current protection, e.g. sneak and fault currents, are mitigated with solid-state resettable fuses PTCs. ASCO Model 160 Series SPDs are designed in accordance with NFPA 780 (2004 edition) requirements, with up to 20 ka of surge current capability. The 160D006S20KXCGN0 model has an isolated ground and is recommended for use at the camera end. 160D006S20KXCGN0 (Edco CX06-MI) OPTION: DIN RAIL KIT AVAILABLE ORDER PART # CXDIN (Edco 11604KIT-CX) Sneak/fault current protection Low insertion loss Shielded case 160D006S20KXCGN0 has an isolated ground 5 year warranty UL 497B General Technical Specifications Operating Voltage Clamping Voltage Operating Current Peak Surge Current Frequency Range Insertion Loss Response Time SPD Technology Connection Type Operating Temperature 5 VDC 6 VDC 0.15 A 20 ka (8 x 20 µs) 0 to 20 MHz < 0.1 db at 20 MHz < 0.5 ns GDT, SAD, w/ Series PTC BNC, 50/75 Ohm -40 C to +85 C Dimensions (in / mm) 160D006S20KXCXN0 = 1.5 H x 1.0 W x 3.25 L [38.1 x 25.4 x mm] 160D006S20KXCGN0 = 1.5 H x 1.0 W x 4.0 L [38.1 x 25.4 x mm] Weight (oz / kg) 160D006S20KXCXN0 = 2.3 oz [0.07 kg] 160D006S20KXCGN0 = 3 oz [0.09 kg] Certifications UL 497B Ordering Information Other configurations available, please contact factory. MODEL Former Model Name 160D006S20KXCXN0 Edco CX06-M 160D006S20KXCGN0 (w/ Isolated Ground) Edco CX06-MI ACCESSORIES Former Accessory Name CXDIN 11604KIT-CX Installation Instructions Head-End Equipment Model 160D006S20KXCXN0 or 160D006520KX16NO (16 Channel Rackmount) (Keep ground wire as short as possible) APPLICATION Head-End Camera-End DIN Mounting Kit for 160D006S20KXCXN0 Model 160D006S20KXCGN0 (Keep ground wire as short as possible) Camera-End Equipment To AC Power Ground To AC Power Ground or Building Ground 38

39 Data / Signal SPDs APT BNCA10kA BNC In-Line Coax SPD BNCA10kA is a premium SPD intended for Severe Service at BNC coaxial connections for video equipment such as CCTV cameras. The BNCA10kA SPD features Three Stage Series Hybrid Surge Protection Primary Course Protection: Gas Discharge Tubes (GDTs) Series Current Limiting Component Secondary Fine Protection: Silicon Avalanche Diodes (SADs) Easy to Install, Din-Rail Mounting Bracket Included Performance Specifications Nominal Operating Voltage Maximum Operating Voltage Maximum Signal Current I max Surge Current Rating (8/20µs) 5V 8V 300mA 10kA Clamping Voltage (Pin-Shield) 8/20µs, 5kA: 13.2V 10/700µs, 1kV: 14.7V Digital Transmission Rate Analog Frequency Range Insertion Loss Response Time Connection Type Discrete Modes of Protection Quality & Validation RoHS - compliant 5 year warranty (longer optional) Individually Tested prior to shipment ISO 9001:2008 Quality Management System CE Mark 10Mbps 0-10Mhz 0.5dB@10MHz <1ns BNC, 50 / 75 ohm Pin-Shield, Shield-Ground Design Designed, Manufactured & Tested consistent with: IEEE C IEEE C IEEE C , C & C62.45 IEEE Location Categories C, B and A NFPA 780 Lightning Protection IEC Shield - Ground Isolation The BNCA10kA includes separate protection modes for Pin to Shield and Shield to Ground. This prevents SPD ground loops and possible signal interference caused if a long run of cable references a different ground than the head-end ground. Physical Specifications Intended for use within a weather-resistant enclosure Relative Humidity Range: 0-95% non-condensing Operating Temp: -40 C (-40 C) to +176 F (+80 C) Weight: 0.25lbs (100g) Dimensions: 3.35 (85mm long) x 1 square (25mm) Pre-wired with 2 (60cm) of #12 AWG ground conductor (User to cut to shortest length possible) Anodized Extruded Aluminum Case; metallic bracket BNC gender changers are available Installation This is a directional, in-line series-connected SPD. PROTECTED end of SPD must be at equipment or camera end. UNPROTECTED end must be at cable end. Industry Best Practices recommend SPDs at both ends of cabling. Grounding: Locate SPD such that Ground lead is as short and straight as possible. Connect to a reliable ground, which should be the same ground reference for power and Pan-Tilt-Zoom (if equipped). Trim Ground lead as appropriate. Inches matter! Do not coil excess lead - cut off excess lead. Crimp-attach included wire terminal and connect to reliable ground. Din-Rail bracket does not electrically ground this SPD. SPD attachment to Din-Rail is not mandatory. All applicable Code(s) and regulation(s) must be followed. If SPD problems are suspected, remove SPD and test system. If system operates normally, replace SPD. 39

40 AC Power Filter / SPDs Series Connected Model 166 (Edco CX-HFN) High Frequency Coax Protector N-Type The ASCO Model 166 surge protectors are designed to protect sensitive electronic equipment from damage due to excessive voltage or currents generated by lightning or static build-up. The Model 166 offers low signal loss at frequencies up to 4 gigahertz. The unit also has a replaceable protection cartridge (CX-RC). The Model 166 accommodates both bulkhead mount and stud mount. The input and output connections are interchangeable. Low signal loss 5-year warranty N-Type Connectors General Technical Specifications Operating Voltage Clamping Voltage Operating Current Peak Surge Current Maximum Power Impedence Frequency Range Insertion Loss SPD Technology Connection Type Operating Temperature Dimensions (in / mm) Weight (oz / kg) Warranty 130 VDC 150 VDC 1 A 10 ka (8 x 20 µs) 10 Watts 50 Ohms 0 to 4 GHz GHz; 1 4 GHz Gas Discharge Tube (GDT) N-Type -35 C to +85 C 1.25 H x 1.0 W x 2.5 L [32 x 25.4 x 64 mm] 4 oz [0.11 kg] 5 years Ordering Information MODEL Former Model Name 166D150S10KGCXN0 Edco CX-HFN-FF 166D150S10KGCMN0 Edco CX-HFN-FM APPLICATION (Female-Female) (Female-Male) 40

41 Data / Signal SPDs Model 185 (Edco CAT6-POE Series) CAT6 Power-Over-Ethernet The ASCO Model 185 is designed to work on Category 6 Power-Over-Ethernet transmission line applications and is ideal for protecting expensive computer and video equipment from damaging surges and transients. Transmission lines provide easy access for transients to enter a facility putting vital equipment at risk. The ASCO 185D068S10KXRGN0 is available with an isolated ground to be used at the equipment end in order to prevent circulating ground currents. Up to four ASCO Model 185s can be installed using optional ASCO C6MP4 mounting bracket. General Technical Specifications Exceeds Category 6 transmission values Three stage hybrid circuit DC over Ethernet all pins 185D068S10KXRJN0 185D068S10KXRGN0 Operating Voltage 0-57 VDC Clamping Voltage 68 VDC Operating Current* 0.75 Amp Per Pin Peak Surge Current 10 ka (8 x 20 µs) Per Pair Insertion Loss < 0.1 db Topology Two Port Series Modes of Protection All Lines (1-8) Protected (L-L) and (L-G) Signal High-Low; High-Ground; Low-Ground Transmission Speeds 10BaseT; 100BaseT; 1000BaseT SPD Technology GDT, SAD, Series PTC Input/Output Connection RJ-45 Jacks (Shielded) RJ-45 Jacks (Isolated) CAT 5 Output Cable Shielded RJ-45, 7 (.18M) Unshielded RJ-45, 7 (.18M) Ground Terminal Stud Stud (Isolated) Operating Temperature -40 C to +85 C (operating current adjusted to +85 C) Operating Humidity 0-95% Non-Condensing Dimensions (in / mm) 7.91 L x 3.48 W x 1.89 H [201 x 88.5 x 48 mm] Material Aluminum Mounting Flange Weight (oz / g) 5 oz [142 g] Certification UL 497B Listed, Tested to IEC (Complies to IEEE 802.3AT and 802.3AF) Optional mounting bracket Optional DIN mounting kit 5 year warranty UL 497B Ordering Information MODEL Former Model Name 185D068S10KXRJN0 Edco CAT6-POE 185D068S10KXRGN0 Edco CAT6-POE-I ACCESSORIES Former Model Name C6MP4 C6-MP4 Installation Instructions APPLICATIONS CAT6 Protection CAT6 Protection with Isolated Ground Multi-Unit Mounting Bracket Single unit DIN Mounting Kit * C6DIN 11604KIT-C6 (Sold Separately) *Includes DIN clips and hardware to mount a single unit. 1. Mount the SPD as close as possible to the protected equipment and secure. #6 hardware is recommended. 2. Connect a #10 ground wire using a ring terminal (not provided) to the SPD ground stud. Connect the opposite end of the wire to a building approved ground. Wire should be short and straight as possible. 3. Connect the Model 185 supply cable (with RJ-45 connector) to the INPUT side of the SPD. 4. Complete the circuit by connecting the CAT5 cable (provided) from the output of the SPD to the protected equipment. Optional Multi-Unit Mounting Bracket (Sold Separately) Part Number: C6MP4 Bracket accommodates up to four Model 185 surge protectors. Bracket s ground lug allows all devices to share one single ground connection. Higher Operating Currents * For applications requiring higher Operating Currents, input connections can be paralleled to meet the desired rating. 41

42 Data / Signal SPDs Model 184 (Edco CAT6-5POE) CAT6/CAT5 Power-Over-Ethernet The ASCO Model 184 is designed to work on Category 5 Power-Over-Ethernet transmission lines as well as Category 6 applications. Ideal to protect expensive equipment against surges and transients entering a building on exposed transmission lines. Exceeds Cat 5 & 6 transmission values CAT5 POE compatible CAT6 compatible Applications up to mA 5 year warranty General Technical Specifications Operating Voltaget Clamping Voltage Operating Current Peak Surge Current Frequency Range Insertion Loss SPD Technology Connection Type Operating Temperature Dimensions (in / mm) Weight (oz / kg) Warranty 0-57 VDC 68 VDC 350 ma 60 A (10 x 1000 µs) 0 to 250 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode (SAD) Female-Female RJ-45 Jacks -40 C to +85 C 0.8 H x 1.0 W x 2.3 L [20.3 x 25.4 x 58.4 mm] 1 oz [0.02 kg] 5 year Installation Instructions 1. Mount the SPD as close as possible to the protected equipment. 2. Connect the supply cable (with RJ-45 connector) to the INPUT side of the SPD. 3. Complete the circuit by connecting the output of the SPD to the protected equipment. Circuit Diagram Ordering Information MODEL Former Model Name 184D065S060SRJN0 Edco CAT6-5POE-FF 184D065S060SRMN0 Edco CAT6-5POE-MF APPLICATION RJ-45 (female-to-female) RJ-45 (male-to-female) 2 2 IN Typical OUT (4x) 1 1 Low Capacitance Neg Steering Diodes Silicon Avalanche Diodes Low Capacitance Pos Steering Diodes Dimensions 0.8 [20.3] 2.3 [58.4] 1.0 [25.4] 42

43 Data / Signal SPDs Model 138 (Edco RJA-RJD Series) RJ-45 Telephone/Data The ASCO Model 138 are four pair telephone/data line protectors that implement advanced two stage hybrid design. These units address over voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology, which consists of solid state resettable fuses. The ASCO Model 138 incorporates female jacks in and out. The ANALOG Model 138 voltage clamp is set for C.O. Trunks and Analog Telephone Extensions (with ring in voltage), and the DIGITAL Model 138 voltage clamp is set for Digital Extensions (no ring in voltage). <1 nanosecond response time Solid-state resettable fuses PTCs Silicon breakover technology Low capacitance Line-to-line protection Tip & ring to ground protection 4 pair protection 5 year warranty UL 497A General Technical Specifications Installation Instructions Operating Voltage Clamping Voltage Operating Current 48, 220 VDC 55, 280 VDC 0.15 A To Protected Equipment Peak Surge Current 200 A (10 x 1000 µs) Frequency Range Insertion Loss 0 to 50 MHz < 0.1 db at 50 MHz Model 138 SPD Technology Connection Type Operating Temperature Dimensions (in / mm) Weight (oz / kg) Certifications Silicon Breakover Devices w/ Series PTC RJ-45 Jacks -40 C to +85 C 1.0 H x 2.5 W x 4.25 L [25.4 x 63.5 x 108 mm] 3 oz [0.09 kg] UL 497A, CUL Equipment (Protected) (Unprotected) Line Gnd Building Approved Ground Ordering Information MODEL Former Model Name 138D280S200SRJN0 Edco RJA D055S200SRJN0 Edco RJD-45 APPLICATION Analog Phone Digital Phone Model 138 To Telco The ASCO Model 138 is intended for indoor use only and shall be employed on the equipment side of a listed primary telephone protector. 43

44 Highway Lighting Submersion Tested Seven feet submersion for 120hrs 50+ hours energized at 480VAC while submerged Test Report Available Installation Instructions 1. Check voltage source to verify that the correct Model 235 is being installed. 2. Disconnect power to light pole before beginning installation of surge protector. 3. Remove hand hole panel on pole to gain access to the light wiring. 4. Disconnect wire nuts connecting wire from electrical service to light. Check to ensure no voltage is present. 5. Connect line side of Model 235 to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is connected to Line 2 or Neutral depending on the voltage. 6. Connect the load side of the Model 235 to wires going up to the light. L1 is connected to Line 1 (hot), L2 is connected to Line 2 or neutral depending on the voltage. 7. Connect the Ground wire on the Model 235 to the ground lug or screw inside the light pole. 8. Carefully push the surge protector and wiring back inside the light pole and attach the hand hole panel on pole. 9. Model 235 comes with a green status LED that indicates that power is applied and that the unit is protecting if illuminated. If the LED is out there is probably no power coming to the unit but can also can indicate that the unit has failed and needs to be replaced. Wiring LEAD LENGTH GAUGE COLOR CONNECTION AWG Green Ground Model 235 (Edco SHAS Series) Highway Lighting Protection The ASCO Model 235 surge protector is a compact watertight device that is designed to be installed directly within a light pole to protect the sensitive lighting ballast or power supply from damaging transients. Model 235 easily fits into the 3 x 5 hand hole located at base of the light pole and is wired in series with the load for the best performance. This series contains a green status LED that will go out in the event the units protection has been reduced. This enables maintenance personnel to identify if the unit needs to be replaced. Fully encapsulated for water resistance Submersion tested to satisfy waterproof requirements Series connected surge protection Metal Oxide Varistor (MOV) Technology General Technical Specifications Model NF (Edco SHAS-120) All modes of protection Protected status LED Compact design - fits easily in highway or parking lot light pole 5 year warranty LF (Edco SHAS-240) NF (Edco SHAS-277) LF (Edco SHAS-480) Operating Voltage 120 VAC 240 VAC 277 VAC 480 VAC Maximum Continuous Operating Voltage (MCOV) 150 VAC 320 VAC 320 VAC 550 VAC Voltage Configuration Single Phase, 2W + G Continuous Operating Current 15 A Operating Frequency Hz Modes of Protection L-N, L-G, N-G L-L, L-G L-N, L-G, N-G L-L, L-G Total Peak Surge Current 36 ka Clamping Ringwave 400V (L-N) 708V (L-L) 708V (L-N) 1,500V Combination 394V (L-N) 684V (L-L) 684V (L-N) 1,260V Combination 564V (L-N) 876V (L-L) 876V (L-N) 1,780V Combination 1,160V (L-N) 1,400V (L-L) 1,400V (L-N) 2,560V (L-L) Status Indication Green LED Connection Type Series Connected Wire Type #12 AWG (See Wiring Chart on pg. 2) Operating Temperature -40 C to +85 C Dimensions (in/mm) 1.5 H x 2.0 L x 2.0 W [38.1 x 50.8 x 50.8 mm] Weight (lbs/kg) 0.52 lbs [0.24 kg] Dimensions 1.5 [38.1] AWG Black L-1 (Hot) AWG Black L-2 (Neutral or Hot) 2.0 [50.8] 2.5 [63.5] 2.88 [73.15] 2.0 [50.8]

45 Highway Lighting Model 235 (Edco SHA Series) Highway Lighting Protection ASCO Model 235 provides surge protection for highway lighting/street pole applications. The suppressor is encapsulated in a compact watertight enclosure that can be installed inside the pole. Model 235 is available in 120V, 240V, 277V and 480V Single Phase models. In addition, optional Low Capacitance (LC) and Both Black leads (BB) models are offered. Fully encapsulated for water resistance Submersion tested to satisfy waterproof requirements Metal Oxide Varistor (MOV) Technology Line-to-Ground Protection Neutral-to-Ground Protection No Follow Current Solid State Design 5 Year Warranty General Technical Specifications Model NF (Edco SHA-1203) LF (Edco SHA-2403) NF (Edco SHA-2773) LF Edco SHA-4803 Operating Voltage 120 VAC 240 VAC 277 VAC 480 VAC Maximum Continuous Operating Voltage (MCOV) 150 VAC 275 VAC 320 VAC 550 VAC Voltage Configuration Single Phase 2W+G Continuous Operating Current 30 A Operating Frequency Hz Modes of Protection L-G, N-G Total Peak Surge Current Rating 39 ka Clamp 1ma (V peak) 240 V 430 V 510 V amps 395 V 710 V 850 V 1500 V Connection / Wire Type Series Connected; Wire Leads Current Drain 100 microamps Insulation to Ground > 600 Volts Response Time < 25 nanoseconds Operating Temperature -40 C to +85 C Dimensions (In/mm) 0.8 H x W x 5.3 L [20.3 x 73.0 x mm] Weight (lb/kg) 1 lb. [0.45 kg] Installation Instructions 1. Check voltage source to verify that the correct model ASCO Model 235 is being installed. 2. Disconnect power to light pole before beginning installation of surge protector. 3. Remove hand hole panel on pole to gain access to the light wiring. 4. Disconnect wire nuts connecting wire from electrical service to light. Check to ensure no voltage is present. 5. Connect line side of Model 235 to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is connected to Line 2 or Neutral depending on the voltage. 6. Connect the load side of the Model 235 to wires going up to the light. L1 is connected to Line 1 (hot), L2 is connected to Line 2 or neutral depending on the voltage. 7. Connect the Ground wire on the Model 235 to the ground lug or screw inside the light pole. 8. Carefully push the surge protector and wiring back inside the light pole and attach the hand hole panel on pole. Dimensions 2.95 [74.93] 1.17 [29.72] Typical 1.17 [29.72] Typical Wiring LEAD LENGTH GAUGE COLOR CONNECTION 22 6 AWG Green Ground AWG Black L-1 (Hot) AWG White L-2 (Neutral or Hot) 4.86 [123.44] 5.25 [133.35] 0.80 [20.3] 45

46 FAILURE TO KEEP AWAY WILL RESULT Medium Voltage Model 950 (APT MVF Series) DANGER HIGH VOLTAGE 1500VAC DANGER ALTO VOLTAJE DANGER KEEP AWAY CONTAINS NO USER SERVICEABLE PARTS IN DEATH OR SERIOUS INJURY SPD Medium Voltage SPD with Dedicated Fuse Box Intended for Large Industrial & Heavy Duty Applications: Oil & Gas, Water & Wastewater, Industrial Process, Chemical, Data Centers, Manufacturing, Paper & Pulp, Etc. Voltage Specific Design Highly Configurable 50-60Hz and VFD frequencies All Modes of Protection Wires Included HIGH VOLTAGE Fuse Box Represents a typical installation of 950 SPD Design Attributes Low clamping voltage for maximum equipment protection Parallel design MOV suppression allows installation flexibility Bi-directional operation for positive and negative polarity surges Solid state, fully automatic action & reset Large-Block, 40mm, MOVs Intended for High Energy applications including all IEEE C Inorganic silica particle encapsulation Noncombustible at extreme temperature Superior gaseous expansion tolerance Double insulated against ground fault or arcing with redundant and separate polypropylene and polyethylene layers Elastomeric Ceramgard potting protects against environmental contaminants 46 Performance Specifications Available Surge Current Ratings: 120kA Per Phase 240kA Per Phase All Mode Protection: A-B, B-C, A-C, A-G, B-G, C-G Proven large block 40mm round MOV Technology Less than 1 nanosecond response time Physical Specifications NEMA 4 (IP66) Heavy Gauge Steel Enclosure Dimensions: 12 x 12 x 6 (31cm x 31cm x 15.5 cm) Weight: 65 lbs (29.5kg) Relative Humidity Range: 0 95% Non-Condensing Operating Temperature: -40 C (-40 F) to +85 C (+185 F) Pre-wired with 2 (0.61 Meters) #6 AWG stranded leads for connection to Fuse Box Quality One (1) Year Warranty on Optional Monitoring Package RoHS- compliant ISO 9001:2008 Quality Management System ISO 17025:2005 Laboratory Qualification Fuse Box Design Attributes Designed to be installed in front of and in-line with ASCO s Medium Voltage SPD Fuse Box included as part of the 950 Non-conductive NEMA 4X Polycarbonate enclosure Stainless steel lockable latches Connecting wires from Fuse Box To Power System included: 2.4m (8 ft) of #6 AWG, 25kV wire each (3 Phase, 1 Ground) Additional 6kV sleeving on each wire for added safety Two (2) 1 ¼ threaded hubs included - to enter and exit enclosure Includes 3 Bussmann fuses: model 5.5CAVE (5.5kV, 15A) Includes 6 of conduit for SPD to Fuse Box connection Fuse Box Physical Specifications NEMA 4X (IP 66) Polycarbonate enclosure Dimensions: 18 x 16 x 10 (457.2mm x 406.4mm x 254mm) Weight: 35 lbs (15.9 kg) Relative Humidity Range: 0 95% Non-Condensing Operating Temperature: -40 C (-40 F) to +85 C (+185 F) Maximum Voltage and Current: 5500VAC and 15A Torque Value: 9 Newton-Meters (80 Inch-Lbs) Fuse Box Wire Terminal Sizes: (Wires are included) Phase Wires: #8 AWG 1/0 AWG Ground Wires: #14 AWG - 1/0 AWG Optional Diagnostic Monitoring (Fuse box not shown) Allows for on-site or remote monitoring of suppression circuit, grounded phase or phase loss High Intensity Green LED indicator lights for each individual phase Bright enough for drive-by visual confirmation Form C Dry Contact Relay for each individual phase Available on 120kA models only with NEMA 3R vented enclosure