[645mm, 949mm, 1254mm] Use only when exposed to salt spray and harsh chemicals. This option is not required for normal outdoor exposure!

Transcription

1 lient Project name Order# Type Qty TURS N NITS Physical : Low copper content extruded aluminum housing vailable in 1', 2', 3' or 4' sections lectro-statically applied polyester powder coat finish Machined aluminum end caps and silicone gaskets Stainless steel hardware lear tempered glass lens symmetric wallwash, 8 x 8, 10 x 10, 10 x 30, 10 x 60, 10 x 90, 15 x 25, 30 x 30, 30 x 60, 35 x 35, 50 x 80, 60 x 60, 80 x 80, or 90 x 90 optics IP66 IK07 rated (asymmetric wallwash lens is IK06 rated) Meets 3 NSI Vibration standard for bridge applications orrosion-resistant coating for hostile environments 2 Performance : 2200K, 2700K, 3000K, 3500K, 4000K, Red, reen, lue static colors available RI value: 80+ Minimum 1fc ( ft (43m) distance (HO 4000K, 4' unit, 10 x 60 optic) Lumen maintenance: 120,000 hrs 25 ] Lumen measurements comply with LM standard Resolution per foot or per fixture (configured with LumenI V3 software & MX/RM) Operating temperatures: -25 to 50 [-13 to 122] lectrical : Line voltage luminaire for 100 to 277V Power and data in 1 cable (#16-5) nd-to-end option (T): 16" black input cable, no jumper cable needed 252ft [77m] maximum cable and fixture run length, non-dimming, 277V, RO version 164ft [50m] maximum cable and fixture run length, non-dimming, 277V, HO version 5W/ft version meets SHR standards for linear lighting on building facades 3 8.5W/ft Regular Output version W/ft High Output version 3 imming options: Lumentalk, 0-10 volt, LI, Lutron cosystem or MX/RM enabled IK07 1 Photometric Summary 4ft HO, 4000K elivered Output [lm] Intensity [peak cd] WW 3,592 5,159 8ºx8º 4,045 77,896 10ºx10º 3,768* 38,346* 10ºx30º 3,830 30,056 10ºx60º 3,692 19,654 10ºx90º 3,576 7,897 30ºx30º 3,765 14,726 30ºx60º 3,862* 5,119* 60ºx60º 3,447* 3,015* 90ºx90º 3,592 1,886 Photometric performance is measured in compliance with ISN LM *stimated. onsult Lumenpulse website for the latest IS and LT files " [340mm] 1 " 4 [7mm] Minimum spacing 25 3, " 8 ", " [645mm, 949mm, 1254mm] " [59mm] TOP VIW Input cable 16" [406mm] 1ft fixture, T option shown RONT VIW 2" [51mm] 4" [102mm] 2ft, 3ft and 4ft fixtures, T option shown 1 symmetric wallwash lens is IK06 rated. 2 Use only when exposed to salt spray and harsh chemicals. This option is not required for normal outdoor exposure! 3 SHR version not available for 1' fixture lengths. Power consumption is typically 20% higher for 1' fixture lengths " [89mm] SI VIW 1/13 onsult

2 SYMMTRI WLLWSH OPTI IN SI TIL Wall side Wall side INPUT WWL symmetric Wallwash Optic, Left eed INPUT WWR symmetric Wallwash Optic, Right eed TOP VIW lways position frosted side toward the wall *ixture s feeding side is based on uplight installations. eeding sides are reversed when fixture is used in a downlight application. Recommended setback from wall is 1/10 of the wall height. xample: 2ft [0.6m] setback for a 20ft [6m] wall. RONT VIW RIHT SI VIW (ixture pointing upwards) 2/13 onsult

3 MOUNTIN OPTIONS Surface Mount SM Slim djustable Mounting UMP ixed Mounting 1 8 " [3mm] 3 8 " [10mm] R 1 8 " [4mm] " [83mm] 3 8 " [10mm] " [71mm] SM Mounting Hole Pattern Wall Mount UMS Universal djustable Mounting /8 [10mm] 3/4 [19mm] 3 1/2 [89mm] 3/16 [5mm] /8 [73mm] 60 WM2 djustable Wall Mounting 2" 0 2X 9/32 THRU LL UMP Mounting Hole Pattern -60 WM6 djustable xtended rm Mounting 6" /8 [10mm] 3/4 [19mm] 3/8 [10mm] 2 1/2 [64mm] /4 [45mm] 115 2X 9/32 THRU LL WM12 djustable xtended rm Mounting 12" 0 UMS Mounting Hole Pattern /16 [27mm] 3/8 [10mm] WM18 djustable xtended rm Mounting 18" 0 2 1/2 [64mm] X 1/4 THRU LL 1 3/4 [45mm] " " 8 " [35mm][108mm][187mm] " " [340mm] [492mm] WM Mounting Hole Pattern 3/13 onsult

4 LOUVR SSORY INSTLLTION TIL Not suitable for asymmetric wallwash optic TOP VIW lade spacing 1" [25mm] ", 25 ", 37 7 ", 49 " [341mm, 646mm, 951mm,1256mm] " [60mm] lade depth 7 16 " [11mm] " [24mm] " [60mm] 4" [102mm] RONT VIW LOR Radial Louver for Lumenfacade (See page 6 for ordering code) SI VIW OPTION T - nd-to-end configuration, 16" black input cable, no jumper cable needed. T Leader able (order separately) T Input able 4/13 onsult

5 SSORIS Order separately ontrol Systems: ontrol oxes: LTO2 LU LI LI-LT LTN X L Lumentouch is a wall mount MX 512 controller keypad. Lumencue is a US / mini S MX 512 controller. LumenI is a diagnostic and addressing MX 512 controller. It must be specifi ed for all MX applications. Refer to LI specifi cation sheet for details. LumentalkI is a diagnostic and addressing controller. It must be specifi ed for all Lumentalk (LT) applications. Refer to LI-LT specifi cation sheet for details. Lumentone is a simple pre-programmed MX 512 controller with a push button rotary dial and live feedback. MX/RM control box. Up to six power and data outputs to fi xtures or fi xture runs. thernet enabled option. Refer to X specifi cation sheet for details. Lumentalk ata ridge, 0-10V or MX output. Refer to L specifi cation sheet for details. 5/13 onsult

6 SSORIS - continued Order separately Leader and Jumpers ables for Standard onstruction : LOL- -ST- - LOJ- -ST- - Leader able for Lumenfacade. Please specify certification (UL or ), cable length (10', 25', 50',100', 150' or 200' [3m, 7.6m,15.2m, 30m, 45m or 61m] standard) and cable color (K-lack or WH-White, connectors are black as standard). Suitable for dimming/data and non-dimming applications. Sealing endcap is mandatory for any unused connector. (1) included with every leader cable. onsult Lumenfacade leader cable specifiation sheet for details. Jumper able for Lumenfacade. Please specify certification (UL or ), cable length (2', 3', 4', 5' or 50' [0.6m, 0.9m, 1.2m, 1.5m or 15m] standard) and cable color (K-lack or WH-White, connectors are black as standard). Lengths between 5' and 30' [1.5m and 10m] are also available, please specify desired length in 1' [0.3m] increments. Suitable for dimming/data and non-dimming applications. onsult Lumenfacade jumper cable specifiation sheet for details. Leader and Jumpers ables for nd-to-nd (T) Option : LOL- -T - LOJ- -T- - Leader able for Lumenfacade, T option. Please specify certification (UL or ), cable length (10', 25', 50',100', 150' or 200' [3m, 7.6m,15.2m, 30m, 45m or 61m] standard) and cable color (K-lack or WH-White, connectors and fixture input cables are black as standard). Suitable for dimming/data and non-dimming applications. Sealing endcap is mandatory for any unused connector. (1) included with every leader cable. onsult Lumenfacade leader cable specifiation sheet for details. Jumper able for Lumenfacade, T option. Please specify certification (UL or ), cable length (1', 2', 3', 4', 5' or 50' [0.3m, 0.6m, 0.9m, 1.2m, 1.5m or 15m] standard) and cable color (K-lack or WH-White, connectors and fixture input cables are black as standard). Lengths between 5' and 30' [1.5m and 10m] are also available, please specify desired length in 1' [0.3m] increments. Suitable for dimming/data and non-dimming applications. onsult Lumenfacade jumper cable specifiation sheet for details. Radial Louver : Not suitable for asymmetric wallwash optic LOR - Radial louver for Lumenfacade. Louver blade depth: 7/16" [11mm]; louver blade spacing: 1" [25mm] Please specify nominal length (1', 2', 3' or 4' [0.3m, 0.6m, 0.9m or 1.2m]) and finish (K-lack Sandtex, RZ-ronze Sandtex, SI-Silver Sandtex, or WH-Smooth white. ustom color available on request, please specify as together with RL color : ). The addition of a louver will affect beam distribution, consult factory for application support. 6/13 onsult

7 RSOLUTION TILS pplicable for MX/RM control option only. ixture resolution can be configured on-site within the LumenI V3 software. MX/RM enabled X is required. Resolution per foot: each foot is addressed independently MX RSSS: TOP VIW LO 48 inches LO 48 inches Resolution per fixture: each fixture is addressed independently MX RSSS: 1 2 TOP VIW LO 48 inches LO 48 inches 7/13 onsult

8 TYPIL WIRIN IRMS Wiring olor ode merican olor ode olor ode US reen Yellow/reen round lack rown Live V White lue Neutral Red/Purple lack 0-10V / ata + Orange rey 0-10V / ata - Non-imming (NO) Non-imming (NO) - Wiring detail - Power input ( V) - Junction box (by others) - Leader cable (LOL) - Lumenfacade (LO-NO) - Jumper cable (LOJ) - Sealing end cap - Power input - To fixture - Line - round - Neutral - Wire-nuts (by others) - Junction box (by others) onsult factory for specific applications and maximum fixture count/cable length recommendations. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. 8/13 onsult

9 TYPIL WIRIN IRMS - continued Wiring olor ode merican olor ode olor ode US reen Yellow/reen round lack rown Live V White lue Neutral Red/Purple lack 0-10V / ata + Orange rey 0-10V / ata - Lumentalk (LT) Lumentalk 1% minimum dimming value 1% minimum dimming value J K - Third party dimmer/controller - Lumentranslator (LTL-010,MX, -TRI, -LI) - ata wiring (by others) - Power line ( V ) - Junction box (by others) - Lumentalk ata ridge (L-IM or L-MX) - Leader cable (LOL) H - Lumenfacade 1' [0.3m] (LO-IM or LO -MX/RM) I - Jumper cable (LOJ) J - Lumenfacade (LO-LT) (2', 3', or 4' fixture lengths) [0.6, 0.9 or 1.2m] K - Sealing end cap H I Wiring detail using L-IM or L-MX (for 1' fixtures [0.3 m]) - Power input (control over power line via Lumentalk system) - round - Line - Neutral V + / ata V - / ata - - To fixture Lumentalk (LT) - Wiring detail (for 2, 3 or 4' fixture lengths [0.6, 0.9 or 1.2m] - Power input (control over power line via Lumentalk system) - To fixture - To Lumentalk ata ridge (for run lengths with 1' fixtures [0.3m]) - Line - round - Neutral - Wire-nuts (by others) H - Junction box (by others) H onsult factory for specific applications and maximum fixture count/cable length recommendations. Lumentalk ata ridge required for 1' [0.3m] fixture lengths. or applications with all fixtures controlled as 1 zone: fixtures and Lumentalk ata ridge must be specified as IM. Maximum of 10 fixtures per L-IM, consult factory for applications that require additional capabilities.or application with fixtures controlled individually: fixtures and Lumentalk ata ridge must be specified as MX, 2-step commissioning process: 1 - MX/RM system using LumenI software and a LI, 2 - Lumentalk system using LumentalkI software and a LI-LT. Maximum of 32 fixtures per L-MX. onsult factory for details. or MX applications: 1 MX controller per Lumentalk network, maximum of 48 MX channels per Lumentalk network (minimum step transition update rate is 1 second, minimum fade time between two colors is 1 minute). onsult factory for applications that require additional capabilities. Maximum of 1 transmitter (Lumentranslator or Lumenlink) per system No third party fixtures allowed on the same circuit. onsult factory for LI Lumentalk applications. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. 9/13 onsult

10 TYPIL WIRIN IRMS - continued Wiring olor ode merican olor ode olor ode US reen Yellow/reen round lack rown Live V White lue Neutral Red/Purple lack 0-10V / ata + Orange rey 0-10V / ata V imming (IM) 10% minimum dimming value 0-10V imming (IM) - Wiring detail H J H I - Power input ( V) - Third party dimmer - ata wiring (by others) - Junction box (by others) - Leader cable (LOL) - Lumenfacade (LO-IM) - Jumper cable (LOJ) H - Sealing end cap - Power input - rom third party dimmer V V - - To fixture - Line - round H - Neutral I - Wire-nuts (by others) J - Junction box (by others) onsult factory for specific applications and maximum fixture count/cable length recommendations. 0-10V m ratings: passive dimmer (urrent Sink): 3m per fixture, active dimmer (urrent Source): 0.5m per fixture. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. LI imming (LI) 1% dimming value LI imming (LI) - Wiring detail H - Power input ( V) - Third party LI controller - ata wiring (by others) - Junction box (by others) - Leader cable (LOL) - Lumenfacade (LO-LI) - Jumper cable (LOJ) H - Sealing end cap J - Power input - rom LI controller - ata + - ata - - To fixture - Line - round H - Neutral I - Wire-nuts (by others) J - Junction box (by others) H I onsult factory for specific applications and maximum fixture count/cable length recommendations. Maximum of 64 LI fixtures per LI loop. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. 10/13 onsult

11 TYPIL WIRIN IRMS - continued Wiring olor ode merican olor ode olor ode US reen Yellow/reen round lack rown Live V White lue Neutral Red/Purple lack 0-10V / ata + Orange rey 0-10V / ata - Lutron cosystem nabled imming (S) 1% minimum dimming value Lutron cosystem nabled imming (S) - Wiring detail H J H I - Power input ( V) - Lutron cosystem controller - ata wiring (by others) - Junction box (by others) - Leader cable (LOL) - Lumenfacade (LO-S) (2, 3,or 4ft fixture lengths) [0.6, 0.9,1or 1.2m] - Jumper cable (LOJ) H - Sealing end cap - Power input - rom Lutron cosystem controller - ata + - ata - - To fixture - Line - round H - Neutral I - Wire-nuts (by others) J - Junction box (by others) onsult factory for specific applications and maximum fixture count/cable length recommendations. ach Lutron cosystem enabled fixture has its own address; for the example shown, there are a total of 2 cosystem addresses. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. 11/13 onsult

12 TYPIL WIRIN IRMS - continued merican olor ode olor ode US reen Yellow/reen round lack rown Live V White lue Neutral Red/Purple lack 0-10V / ata + Orange rey 0-10V / ata - Maximum run length by 15 circuit - Lumenfacade HO 15.25W/ft [0.3m] able length/voltage 120V 240V 277V 50ft [15m] leader cable 68ft [21m] 76ft [23m] 84ft [26m] Maximum run length by 15 circuit - Lumenfacade RO 8.5W/ft [0.3m] 50ft [15m] leader cable 120ft [37m] 128ft [39m] 128ft [39m] Maximum run length by 15 circuit - Lumenfacade SHR 5W/ft [0.3m] 50ft [15m] leader cable 128ft [39m] 128ft [39m] 128ft [39m] Star Layout (MX/RM) 1% minimum dimming value - Third party MX/RM controller - ata input (elden 9841 or equivalent, by others) - ata output to next X (optional, not isolated/not boosted) - X-ST - Power input ( V) - Leader cable (LOL) - Lumenfacade (LO-MX/RM) H - Jumper cable (LOJ) I - Sealing end cap H I aisy hain Layout (MX/RM) 1% minimum dimming value H I - Third party MX/RM controller - ata input (elden 9841 or equivalent, by others) - ata output to next X (optional, not isolated/not boosted) - X-S - Power input ( V) - Leader cable (LOL) - Lumenfacade (LO-MX/RM) H - Jumper cable (LOJ) I - Sealing end cap onsult factory for specific applications and maximum fixture count/cable length recommendations. Maximum run length calculations are typically based on 4' [1.2m] fixtures. Maximum of 32 MX/RM enabled fixtures per X output. Maximum of 4 MX/RM repeaters/x cascading in line. Maximum of 6 outputs per X-ST, maximum of 1output per X-S ach fixture requires 1 MX address. SHR version: 5 watts per foot [0.3m], Regular Output version: 8.5 watts per foot [0.3m], High Output version: watts per foot [0.3m]. 12/13 onsult

13 HOW TO ORR LO i-symmetric Housing: LO SHR - Lumenfacade, 5W/ft SHR compliant 1 LO RO - Lumenfacade Regular Output, 8.5W/ft LO HO - Lumenfacade High Output, 15.25W/ft 6 10x30-10 x 30 10x60-10 x 60 10x90-10 x 90 15x25-15 x 25 30x60-30 x 60 50x80-50 x 80 2 Mounting Option: 3 Voltage: volts volts volts volts volts volts SM - Slim djustable Mounting UMP - ixed Mounting 4 UMS - Universal djustable Mounting 4 WM2 - djustable Wall Mounting 2" WM6 - djustable xtended rm Mounting 6" WM12 - djustable xtended rm Mounting 12" WM18 - djustable xtended rm Mounting 18" Length: /8 inches (340mm) (2 kg/4.5 lbs) /8 inches (645mm) (3.17 kg/7 lbs) /8 inches (949mm) (4.75 kg/10.5 lbs) /8 inches (1254mm) (6.35 kg/14 lbs) olors and olor temperatures: 22K K 27K K 30K K 35K K 40K K R - Red R - reen L - lue onsult factory for availability of static Royal lue, 6500K and 90+ RI. 8 inish: K - lack Sandtex RZ - ronze Sandtex SI - Silver Sandtex WH - Smooth white - ustom color and finish (please specify RL color) 5 ontrol: NO - No imming LT - Lumentalk imming 6 IM V imming option 7 LI - LI imming option 8 S - Lutron cosystem nabled imming 9 MX/RM - MX/RM enabled 10 Optics: symmetric WWL - symmetric Wallwash optic, left feed 2 WWR - symmetric Wallwash optic, right feed 2 Symmetric 8x8-8 x x10-10 x x30-30 x 30 35x35-35 x 35 60x60-60 x 60 80x80-80 x 80 90x90-90 x 90 9 Option: T - nd - to - end configuration, 16" black input cable, no jumper cable needed R - orrosion-resistant coating for hostile environments 3V - 3 NSI Vibration Rating 11 - (certification covers uropean conomic rea) 1 Not available for 1' [0.3m] fixture lengths. 2 Right feeding side is standard unless otherwise specified. 3 or best results use with HO fixtures at a 6-inch (15cm) setback from surface. ontact factory for application support. 4 Suitable to use when 3V option is specified. 5 North merican RL colors specified with RL number only are provided with a smooth/high-gloss finish. Please consult factory for other RL textures and glosses, or to match alternate color charts. inal color matching results may vary. 6 Lumentalk system is enabled with L accessory for 1' [0.3m] fixture lengths, see Typical Wiring iagrams pages for details. 1% minimum dimming value. 7 10% minimum dimming value. urrent Sink: 3m/fixture, urrent Source: 0.5m/fixture. 8 1% minimum dimming value. 1 LI address per fixture. 9 vailable for 2' RO [0.6m], 3' [0.9m] and 4' [1.2m] fixture lengths only. 1% minimum dimming value. 1 cosystem address per fixture length. 10 1% minimum dimming value. ixtures set to by fixture resolution. 1 MX address per fixture. 11 vailable with UMP and UMS mounting options only. 13/13 onsult