NUTP3 Series 24V RGB LED Tape Light (Color Changing) Source: 2.5 Watts Per Foot

Transcription

1 NUTP3 Series 24V RG LED Tape Light (olor hanging) Source: 2.5 Watts Per Foot PRODUT DESRIPTION RG LED Tape Light has the colors Red, Green, and lue in every LED diode. Several colors of visual spectrum can be selected and programmed with a 120º viewing angle. stationary color, automatic changing colors and brightness can be selected and changed at anytime with the press of a button. This flexible LED light source is a durable silicone encapsulated tape, cetlus Listed for Wet Location applications and IP65 rated. Features vailable in 16' roll, 12" section, and 6" section Separable every 12", easily disconnected and connected without soldering Field cuttable every 6" or 6 LEDs 120º eam ngle Easy to install; pre-applied 3M tape or 15 acrylic mounting clips (included with roll) Primary olors: Red, Green, and lue ETL Listed for Wet Location and IP65 rated No soldering or additional wiring is required No flicker delay or warm up like compact fluorescent products No UV light or infrared wavelengths 3 Year Limited Warranty onstruction The silicone encapsulated tape can be cut every 6 LEDs at marked intervals. utting does not effect circuit (shrink wrap tube included for concealment). RG Tape Light is also separable every 12", each connection has pre-installed shrink wrap around power connections to ensure wet location listing. Simply slice the clear shrink wrap at each electrical connection, and separate pieces. This eliminates soldering when using partial rolls. Each roll comes with 12" power line connector NRG-710. mounting Each Tape Light roll comes with 15 clear acrylic clips and also comes with pre-applied 3M adhesive tape for simple installation. n optional aluminum channel is available. ELETRIL Power: 24 Volt D Input / 2.5 Watts Per Foot / 40 Watts Per Roll Light Source: 12 RG LEDs Per Foot / 192 LEDs Per Roll Operating Temperature: -25º ~ 60º (-13ºF ~ 140ºF) Life Expectancy: 50,000 Hours Maximum Run Length: 40' (w/ NTL-5100) ONTROLLER Each run requires a controller, which can be linked together for color synchronization. The controller can be controlled locally or with an optional hand held remote. LEls and listings cetlus Listed for Wet Location¹ (not submersible) IP65 Rated alifornia Energy ommission 3 Year Limited Warranty ¹ To maintain wet location when connecting 2 sections; add clear shrink wrap over mating pieces and shrink wrap per instructions. Shrink wrap tubes are included with each roll (5) and section (2). RG Tape Light - select one Tape Light Length NUTP3-16LEDRG = 16' Roll NUTP3-LEDRG/6 = 6" Section NUTP3-LEDRG/12 = 12" Section Type Project atalog No. Lamp/Wattage Dimensions 6" Length 12" Length 16' Length (includes NRG-710) 1/16" Depth 9/16" Width RG ONTROLLER (REQUIRED) NRG-760: 24VD / 360W RG ontroller NRG-761: Hand Held Remote for RG ontroller NRG-860: RG RF ontroller NRG-861: RG RF Hand Held Remote NRG-866: RG RF Wall Mount ontrol HRDWIRE DRivers NTL-530HW: 24VD / 30W lass II Hardwired LED Driver NTL-560HW: 24VD / 60W lass II Hardwired LED Driver NTL-5100: 24VD / 100W lass II Plug-In LED Driver (hardwirable) PLUG-IN DRivers NTL-524: 24VD / 24W Direct Plug-In LED Driver NTL-545: 24VD / 45W Direct Plug-In LED Driver NTL-5100: 24VD / 100W lass II Plug-In LED Driver DRIVER ESSORIES NR-125/6: 6" Extension ord for NTL-530HW & NTL-560HW NR-125/12: 12" Extension ord for NTL-530HW & NTL-560HW NR-125/18: 18" Extension ord for NTL-530HW & NTL-560HW NR-125/72: 72" Extension ord for NTL-530HW & NTL-560HW NR-6035W/6: 6' ord and Plug for NTL-530HW & NTL-560HW NR-6035W/10: 10' ord and Plug for NTL-530HW & NTL-560HW NUSP-Jox: Junction ox required for hardwiring NTL-530HW, NTL-560HW, NTL-5100 RG TPE LIGHT ESSORIES NTL-400: Shrink Wrap Tube (Pack of 5) NTL-403: End ap NRG-700: "Y" Splitter able NRG-701: "X" Splitter able NRG-7xx: Interconnection able (available in 2", 6", 18", 36", 72") NRG-710: 12" Power Line Interconnector NTHR-680: 4' luminum hannel NTHR-685: lear crylic Mounting lips (Pack of 15) NTL-23: 4" luminum hannel, Shallow w/ Wings NTL-24: 4" luminum hannel, Shallow NTL-25: 4" luminum hannel, Deep w/ Wings NTL-26: 4" luminum hannel, Deep NTL-27: 4" luminum hannel, J-Style NTL-28: 4" luminum hannel, orner reate a complete fixture / driver catalog number: Example: NUTP3-16LEDRG / NRG-760 / NTL Gayhart St., ommerce, Phone: FX:

2 luminum hannel Includes plastic diffuser NTL-23: 4' luminum hannel, Shallow w/ Wings luminum hannel Includes plastic diffuser NTL-24: 4' luminum hannel, Shallow luminum hannel luminum hannel NTL-25: 4' luminum hannel, Deep with Wings NTL-26: 4' luminum hannel, Deep luminum hannel NTL-27: 4' luminum hannel, J-Style luminum hannel NTL-28: 4' luminum hannel, orner NTHR-680-4' luminum hannel Tape Light snaps into the channel. Field uttable. Recommended for most installations Gayhart St., ommerce, Phone: FX:

3 24V RG TPE LIGHT ESSORIES NRG " Power Line Interconnector NTL End ap The 12" power line interconnector cable connects a Tape Light run to a Driver. NRG-710 is included with every Tape Light roll (16'). NRG-702-2" Interconnection able NRG-706-6" Interconnection able NRG " Interconnection able NRG " Interconnection able NRG " Interconnection able : Width: 1/2" : Length: 3/8" Used to cover open end of Tape Light. NTHR Mounting lips (Pack of 15) The interconnection cables allow for the linking of any two Tape Lights in any direction or extension of power line interconnectors. The arrow on the interconnection cable must always be facing upward to maintain polarity. Interconnection cables may be joined together for custom lengths. NRG "Y" Splitter able NRG "X" Splitter able Used to mount tape light to surface, includes mounting screws. Pack of 15 are included with every Tape Light roll (16') able Lengths: 3" Splits connection from one Tape Light or Driver into two or three separate Tape Lights. NTL Shrink Wrap Tube (Pack of 5) Used to seal connections made in the field. Neccessary to maintain ETL Wet Listing. Pack of 2 are included with every Tape Light roll and section Gayhart St., ommerce, Phone: FX:

4 24V RG TPE LIGHT LED DRIVER ESSORIES NR-125/6-6" Flexible onnector NR-125/12-12" Flexible onnector NR-125/18-18" Flexible onnector NR-125/72-72" Flexible onnector Used to extend length between NUSP-Jox and NTL-530HW & NTL-560HW. an be joined together to create custom lengths. NR-6035W/6-6' Flexible Power ord NR-6035W/10-10' Flexible Power ord Used to convert NTL-530HW & NTL-560HW into a direct plug-in driver. NUSP-Jox - Junction ox for Hardwired LED Drivers : Width: 4-1/2" : Length: 2-3/4" : Height: 1-1/2" To be used with NTL-530HW, NTL-560HW, or NTL-5100 Drivers. apable of feeding two separate LED Drivers. ccepts Romex or flex. Includes (1) male to male connector and (1) male to female connector. UL Listed Gayhart St., ommerce, Phone: FX:

5 24V RG TPE LIGHT ONTROLLER & LED DRIVERS NTL W Direct Plug-In Driver NTL W Direct Plug-In Driver NRG RG ontroller : Driver Width: 1-3/4" : Driver Length: 1-1/2" : Driver Height: 3-3/4" Direct Plug-In Driver allows direct connection to the LED Tape Light. Includes a 6' Power Line onnector able. NTL-530HW - 30W lass II Hardwird LED Driver NTL-560HW - 60W lass II Hardwired LED Driver : Width: 2" : Length: 4-3/4" : Height: 1" RG ontroller is needed for each tape light run. RG ontrollers can be synchronized to change simultaneously. apable of creating several colors or automated changing of visual spectrum. an be controlled locally or with Hand Held remote (NRG-761). NRG Hand Held Remote ontrol 3-1/4" NTL-530HW NTL-560HW : Driver Width: 1-3/4" 2-3/8" : Driver Length: 5-5/8" 7" : Driver Height: 1-1/4" 1-3/8" Hardwired LED Driver allows for driver to be hardwired with NUSP-Jox (required). The power line connector is 3-1/4" long and the input wire is 4" long. an be converted into plug-in driver with NR-6035W/6 or NR-6035W/10. NTL W lass II Plug-In LED Driver : Driver Width: 2-5/8" : Driver Length: 7-7/8" : Driver Height: 1-3/8" 3-1/4" 4" 6' For remote control of RG ontroller up to 22' away (must be in direct view of controller) Used to program RG Tape Light run to certain color configurations. NRG RG RF Hand Held Remote Working temperature: Power Supply Mode: * 3 Supply Voltage: 1.5V * 3 Transmission Frequency: 2.4Ghz Standby Power onsumption: 0.015mW Standby urrent: 60u Working current: 200u Emission urrent: 10m Remote Distance: about 30m Standby time: 6 months : Width: 1-7/8" : Length: 3-1/2" : Height: 1/4" ord and Plug can be cut to be hardwired with NUSP-Jox. The power line interconnector is 3-1/4" long and the cord and plug is 6'. NRG RG RF ontroller NRG RG Wall Mount ontrol Working temperature: Supply Voltage: D5V-24V Output: 3 hannels onnection Mode: ommon node Static Power onsumption: <1W Output urrent: <8 (each channel) Ouput Power: 12V: <288W, 24V: <576W Working temperature: Supply Voltage: D5V-24V Output: 3 hannels onnection Mode: ommon node Static Power onsumption: <1W Output urrent: <8 (each channel) Ouput Power: 12V: 144W Max, 24V: 288W Max : ontroller Width: 2.45" : ontroller Length: 4.73" : ontroller Height: 0.95" Touch Pad + JOX dimension: () 3-3/8" x 3-3/8" x () 2" JOX-only dimension: 2-3/4" x 3" x 1-5/8" 6505 Gayhart St., ommerce, Phone: FX: