Suzuki Electronic Temperature Sensor Installation Instructions

Transcription

1 Pub B Suzuki Electronic Temperature Sensor Installation Instructions This instruction sheet tells how to install your temp sensor and connect it to a NMEA 2000 network using Suzuki Modular Instrument System (SMIS) network components. You must refer to your digital gauge, sonar or GPS unit's manual for sensor operation instructions. CAUTION Installing SMIS network devices is significantly different from installing components without NMEA 2000 features. Please read all of the installation instructions before proceeding. You should decide where to install all components before drilling any holes. All SMIS capable devices are either NMEA 2000-certified or certification is pending. See our web site for the latest product status information. Temp module Smart module Female NMEA 2000 connector 1

2 The temperature sensor. This sensor consists of a temp sensor module, a blue female locking cable connector and a smart module, which converts analog temperature data to the NMEA 2000 data format. The cable length from the connector to the smart module is 18 inches and from the smart module to the temp module is10 feet. This Temp sensor is designed to operate in a temperature range of 4 to 176 F (-20 to 80 C). This sensor is designed only for use with a SMIS Network. It must be connected to a NMEA 2000 network or it will not function. Tools and Supplies A T connector is the only electronic component needed to attach it to an existing SMIS network. The photo above includes a 2 foot extension cable, T connector, 120- ohm male terminator and 120-ohm female terminator. NOTE: All connectors used to add a temp sensor to a NMEA 2000 network will be black Devicenet connectors as shown above. For complete instructions on setting up a new NMEA 2000 network or expanding an existing one refer to the NMEA 2000 Installation Instructions packed with your temp sensor. Required supplies (not included) for this job are: transom mounting requires one #8 stainless steel screw (3/4" long), screw driver and a sealant (SUZUKI SILICONE SEAL or equivalent). A drill and 1/8" drill bit are needed for the screw pilot hole. Use a 7/8" drill bit for the hole to feed the temp module, smart module or cable connector through a transom or bulkhead. 2

3 Installation The temperature sensor can be mounted in any location where you want to monitor temperature. The most common applications are on a transom to measure surface water temperature, or in a livewell. Wherever you install it, make sure the temp module will be in contact with the water at all times. If it is a transom mount, make sure the location does not interfere with the boat's trailer. After determining the location, use the temp module as a template and mark the hull for the mounting screw pilot hole. Route the temp module and cable over or through the transom to the mounting location. If routing through the transom, drill a 7/8" hole to accommodate the sensor. Make sure the smart module is inboard, and not exposed on the transom. Attach the temp module to the hull with one #8 stainless steel screw, then seal the screw with the below-waterline sealant (SUZUKI SILICONE SEAL or equivalent). Temp module on transom with cable routed through the transom. Notice that the sensor was routed so the smart module is inboard. CAUTION If you drill a hole in the transom for the cable, make sure it is located above the waterline. After installation, be sure to seal the cable hole with the same sealant (SUZUKI SILICONE SEAL or equivalent) used for the screw. Route the sensor's cable connector to the T on the network backbone where you intend to attach it, and plug it in. Connecting to a SMIS Network A network bus is an installed and operational network cable (backbone) running the length of your boat, connected to a power supply and properly terminated. Like your home s telephone wiring with phones in different rooms connected to the same communications line, a network 3

4 bus is the communications line into which NMEA 2000 sensors, devices and display units are attached at various locations in a boat. Network Nodes A network bus is built of network nodes attached to a backbone. A network node is made by inserting a T-shaped connector into the backbone (using the side sockets) and attaching a display unit or sensor to the bottom socket of the T. The T connectors are similar to telephone jacks. The backbone is similar to a phone line running through the boat. As phones must be connected to each other to communicate, only sensors and display units plugged into the NMEA network can share information. Connections found in the middle of the bus will have one or more of these T-shaped connectors with the backbone cables plugged into both sides. Connections at the end of a network will have the backbone plugged into one side, and a terminator plugged into the other, as shown below. Cable from sensor or display unit SMIS device needs an open T. T connector Backbone cable (to rest of bus) Terminator at the very end of the bus SMIS network node located at the end of a NMEA 2000 bus. Adding a Network Node You can add a node anywhere along the network backbone where a connection already exists. This connection could be at the end of the network (between a T connector and a terminator), between two T connectors, between a T connector and a backbone extension cable, or between two extension cables. Wherever you want to add the new node, simply separate the sockets of the old connection and attach your new T connector between them. 4

5 SMIS device connects to new T connector. Existing network node Add T-shaped connector to add device to bus. Attach terminator at end of bus. Add a new device to a SMIS network by attaching a T connector between two T connectors, between a T connector and the end terminator, or between two backbone extension cables. If you want to add a node at the end of the line (as shown in the previous figure), remove the terminator from the very last connector, securely attach the new T connector, and then attach the terminator on the new connector. Either method will allow you to add a device. Additional Network Information Further instructions on creating or expanding a network are illustrated in the NMEA 2000 network setup booklet, which came packed with this instruction sheet. 5

6 Notes 6

7 SMIS 2" Digital Gauge: Temp Sensor Configuration To use a SMIS 2 "digital gauge to configure a Suzuki Electronic Temperature Sensor on a DeviceNet network, press MENU, select SYSTEM SETUP and press MENU. Highlight B. DEVICES and press MENU, which will open the Bus Devices list, a list of devices on the network. Bus Devices works as the device manager for the bus, allowing you to configure, unconfigure and reconfigure your temp sensor. NOTE: You will notice the SMIS 2" gauge does not have an Exit key. Menus will time out after a preset amount of time (3, 5, 10 or 15 seconds). Refer to your gauge's instruction manual for more information on the Timeout feature. SMIS 2" Multi-function Digital Gauge. Boat Setup If this is the first time you have turned on your SMIS 2" gauge, you will have to complete Boat Setup before you will be able to configure your temp sensor. If you have already completed Boat Setup skip ahead to the segment covering Temp Configuration. NOTE: If you want to access the Setup screen after an engine-tank configuration has been chosen, press MENU, highlight SYSTEM SETUP and press MENU. Choose ENG/TANK and press MENU twice. The following message will appear: Hit menu to reset Eng/Tnk. Press MENU. The Setup screen will appear with Boat Setup highlighted. 7

8 To execute Boat Setup: 1. With Boat Setup highlighted on the screen, press MENU. The Boat Setup menu will appear, allowing you to select an engine-tank configuration that matches the number of engines and fuel tanks on your vessel. Boat Setup options include: 1 En/1 Tk, 1 En/2 Tk, 2 En/1 Tk, 2 En/2 Tk, 3 En/1 Tk and 3 En/3 Tk. 2. Select the configuration option that matches number of engines and tanks on your vessel and press MENU. 3. If you selected a configuration with more than one tank you will have to select the tank you want to set up and press MENU, which will open the Tank Size window. (If you choose a single-tank configuration, you will not have to choose the tank. You will be directed straight to the Tank Size window.) 4. Use the UP and DOWN keys to input the number of gallons the tank will hold and press MENU. Repeat steps 3 and 4 for each additional tank. After all tanks have been set up, you will be directed to the main display. Temp Configuration Your gauge has three temp sensor configuration options: Inside, Outside and Water. An unconfigured temperature sensor will appear on the Bus Devices list as UnCfg Temp. To configure a temp sensor: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU. 2. Highlight B. DEVICES and press MENU. After a few moments the Bus Devices list, a list of devices on the network, will appear. 3. Highlight UNCFG TEMP and press MENU. The following message will appear: Hit Menu to Cfg Temp Sns. 4. Press MENU to be taken to the Selecting Temp menu, which will have three options: Inside, Outside and Water. 5. Highlight one of the Temp options and press MENU. The temp sensor has now has been configured. You will automatically be directed to the Bus Devices list. NOTE: If your temp sensor is not updated on the Bus Devices list, you can refresh the list by letting the list time out, then accessing it again. To unconfigure a temp sensor: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU. 8

9 2. Highlight B. DEVICES and press MENU, which will open the Bus Devices list. 3. Select a temp sensor from the Bus Devices list and press MENU. The Configuration Options menu will appear with two choices: Unconfig (Unconfigure) and Reconfig (Reconfigure). 4. Select UNCONFIG and press MENU. The following message will appear: Hit Menu to Unset Device Name. 5. Press MENU to unconfigure the sensor and be directed back to the Bus Devices list, where the temp you unconfigured will be listed as Uncfg Temp. NOTE: If your temp sensor is not updated on the Bus Devices list, you can refresh the list by letting the list time out, then accessing it again. To reconfigure a temp sensor: To reconfigure a sensor, there must be a configuration name available (Water, Outside or Inside). If you try to reconfigure a sensor when the desired configuration name (Water, Outside and Inside) is in use, a Name Already Selected message will appear. If all three temps are configured, meaning there is no name configuration available, follow the first set of instructions. If the desired configuration name is available, follow the second set of instructions. The first set of instructions below will show you how to switch the configuration of a water temp to an outside temp. If all temps configured (Configuration name unavailable): 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU. 2. Highlight B. DEVICES and press MENU, which will open the Bus Devices list. 3. Highlight WTR TEMP on the Bus Devices list and press MENU, which will launch the Configuration Options menu. 4. Select UNCONFIG and press MENU. The following message will appear: Hit Menu to Unset Device Name. 5. Press MENU to unconfigure the sensor and be directed to the Bus Devices list, where the temp you unconfigured (Water Temp) will be listed as Uncfg Temp. 6. Highlight OUT T (Outside Temp) and press MENU. The configuration options menu will appear. 9

10 7. Select RECONFIG and press MENU to open the Selecting Temp menu. Highlight WATER and press MENU. You will be taken back to the Bus Devices list. 8. Highlight UNCFG TEMP and press MENU. The following message will appear: Hit Menu to Cfg Temp Sns. 9. Press MENU to be taken to the Selecting Temp menu. Choose OUTSIDE and press MENU. You will be taken back to the Bus Devices list, where the two sensors will be listed with their new configurations. If desired configuration name available: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU. 2. Highlight B. DEVICES and press MENU, which will open the Bus Devices list. 3. Highlight WTR TEMP on the Bus Devices list and press MENU, which will launch the Configuration Options menu. 4. Select RECONFIG and press MENU to open the Selecting Temp menu. Highlight OUTSIDE and press MENU. You will be taken back to the Bus Devices list, where the temp will now be shown as Out T. (Outside Temp). NOTE: If your temp sensor is not updated on the Bus Devices list, you can refresh the list by letting the list time out, then accessing it again. 10

11 SMIS 4" Digital Gauge: Temp Sensor Configuration To use a SMIS 4" digital gauge to configure a Suzuki Electronic Temperature Sensor connected to the DeviceNet network, press MENU, select SYSTEM SETUP and press ENTER. Highlight BUS DEVICES and press ENTER to open the Bus Devices list. Bus Devices works as the device manager for the bus, allowing you to configure, unconfigure and reconfigure your temp sensor. SMIS 4" Multi-function Digital gauge. Boat Setup If this is the first time you have turned on your SMIS 4" digital gauge you will have to complete Boat Setup before you will be able to configure your temp sensor. If you have already completed Boat Setup, skip ahead to the segment covering Temp Configuration. NOTE: If you want to access the Setup Menu after an engine-tank configuration has been chosen, press MENU, highlight SYSTEM SETUP and press ENTER. Choose ENG/TANK CFG and press ENTER twice. The following message will appear: Press ENTER to reset Eng/Tnk Cfg. Press MENU. The Setup Menu will appear with Boat Setup highlighted. To execute Boat Setup: 1. With Boat Setup highlighted on the screen, press ENTER. A menu will appear, allowing you to choose the number of engines and fuel tanks on your vessel. The Boat Setup menu options are: 1 Eng/1 Tank, 1 Eng/2 Tank, 2 Eng/1 Tank, 2 Eng/2 Tanks, 3 Eng/1 Tank or 3 Eng/3 Tanks. 11

12 2. Use the UP and DOWN keys to select the correct engine-tank configuration for your vessel and press ENTER. After setting the engine/tank configuration, the Tank Size menu will appear with up to three options (Port Tank, Center Tank and Starboard Tank), depending on the engine tank configuration you chose. (If you selected one tank during Boat Setup, you will be taken directly to the Setting Tank Size Window in Step 4.) 3. Select the desired tank and press ENTER, which will open the Setting Tank Size window. 4. Use the UP and DOWN keys to input the number of gallons the tank will hold and press ENTER. Press EXIT and repeat steps 3 and 4 for each of the remaining tanks. 5. After all tanks on your vessel have been set up, press EXIT repeatedly to return to the main display. Temp Configuration Your gauge has three temp sensor configuration options: Inside, Outisde and Water. An unconfigured temperature sensor will appear on the bus devices list as UnCfg Temp. To configure a temp sensor: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 2. Highlight BUS DEVICES and press ENTER. The Bus Devices list will appear. 3. Select an unconfigured temp sensor (UNCFG TEMP) and press ENTER. The following message will appear: Press Enter to Configure Temp Sensor. 4. Press ENTER, which will open the Select Temp menu with three options: Water Temp, Outside Temp and Inside Temp. 5. Highlight the desired option and press ENTER. The temp is now configured. You will be directed to the Bus Devices list. Press EXIT repeatedly to get back to the main display. NOTE: If your temp sensor is not updated on the Bus Devices list, you can refresh the list by closing it, then accessing it again. To unconfigure a temp sensor: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 12

13 2. Highlight BUS DEVICES and press ENTER. The Bus Devices list will appear, showing all devices detected on the network. 3. Choose the temp sensor you want to unconfigure and press ENTER. Select UNCONFIGURE from the temp configuration menu and press ENTER. The following message will appear: Press Menu to UnConfig Device Name. 4. Press ENTER to unconfigure the sensor and be directed back to the Bus Devices list where the temp now will be listed as UnCfg Temp. Bus Devices highlighted in the System Setup menu (left). Searching Bus Devices window (center) with Bus Devices list (right). To reconfigure a temp sensor: To reconfigure a sensor, there must be a configuration name available (Water, Outside or Inside). If all three temp sensors have been configured, you first will have to unconfigure a temp sensor to make its name available for reconfiguration. If you try to reconfigure a sensor when the desired configuration name (Water, Outside and Inside) is in use, a Name Already Selected message will appear. If all three temps are configured, meaning there is no name configuration available, follow the first set of instructions. If the desired configuration name is available, follow the second set of instructions. The first set of instructions below will show you how to switch the configuration of a water temp to an outside temp. If all temps configured (Configuration name unavailable): 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 2. Highlight BUS DEVICES and press ENTER. Select OUT: T (Outside Temp) and press ENTER to open the temp configuration menu. 3. Select UNCONFIGURE and press ENTER. The following message will appear: Press Enter to UnConfig Device Name. 4. Press ENTER to unconfigure the sensor and be taken back to the Bus Devices list. The Outside temp is now unconfigured and will be 13

14 displayed as UnCfg Temp. Its configuration name (Outside) is now available, so you will be able to use it to reconfigure the Water temp sensor. 5. Highlight WTR: T and press ENTER, which will open the temp configuration menu. Select RECONFIGURE and press ENTER. That will direct you to the Temp Selection menu, which will have three options: Water, Outside and Inside. 6. Select OUTSIDE and press ENTER. You will be taken back to the Bus Devices list. The temp you just reconfigured (formerly water temp) will now be displayed as Out: T. 7. To configure the unconfigured Temp (formerly Outside temp), highlight UNCFG TEMP from the Bus Devices list and press ENTER to open the Temp Selection menu, which will have three options: Water, Outside and Inside. Highlight WATER and press ENTER. You will be taken back to the Bus Devices list, where the temp you configured will be displayed as WTR: T. If desired configuration name available: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 2. Highlight BUS DEVICES and press ENTER. Select WTR: T and press ENTER to open the configuration options menu. 3. Select RECONFIGURE and press ENTER to open the Temp Selection menu, which will have three options: Water, Outside and Inside. 4. Highlight OUTSIDE and press ENTER. You will be taken back to the Bus Devices list where the temp will now be shown as Out T. NOTE: If your temp sensor is not updated on the Bus Devices list, you can refresh the list by closing it, then accessing it again. 14

15 How to Obtain Service in the USA: Contact your nearest Suzuki Marine Dealer in Canada: Contact your nearest Suzuki Marine Dealer outside Canada and the USA: Contact the dealer in the country where you purchased your unit. Accessory Ordering Information Please contact your local Suzuki Marine dealer. To locate a Suzuki Marine dealer, visit the web site, and look for the Dealer Locator. To locate a Canadian Suzuki Marine dealer, visit the web site, and look for the Dealer Locator. Or, consult your telephone directory for listings. 15

16 * B* Copyright 2009 All Rights Reserved American Suzuki Motor Corp. 16