2.5 inch Solid State Drive (PATA Type) PC-SSD-1000P, PC-SSD-2000P, PC-SSD-4000P, PC-SSD-8000P User s Guide CONTEC CO.,LTD.

Transcription

1 2.5 inch Solid State Drive (PATA Type) PC-SSD-1000P, PC-SSD-2000P, PC-SSD-4000P, PC-SSD-8000P User s Guide CONTEC CO.,LTD. Thank you for purchasing the CONTEC PC-SSD-P Series. interchangeable with 2.5-inch IDE hard disks. procedures described in this document. This product is a solid state drive Please use this product in accordance with the Product Configuration - Product 1 - Warranty Certificate 1 - User s Guide (this booklet) 1 - Serial number label 1 - Mounting screws 1 set (M3 x 6mm, M3 nylon washers 4pcs) - Jumper 1 Disposal When disposing of the product, follow the disposal procedures stipulated under the relevant laws and municipal ordinances. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely. DANGER WARNING CAUTION DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Handling Precautions WARNING - Do not modify the product. Doing so may cause fire, electric shock. - If smoke or abnormal odor is detected, immediately turn off the PC and peripheral devices and unplug the power cables. - Never touch this product with wet hands. Doing so can short-circuit the product to cause fire, electric shock, and/or failure. 1 PC-SSD-P Series

2 CAUTION - Use only the mounting screws (M3 x 6) provided with the product. Longer screws may damage the interior of the product. - This product is the silicon disk drives for PC/AT compatible (DOS/V compliant) IDE hard disk. - No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. - The contents of this document may be changed in the future without prior notice. - All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD. - Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document or for any results of using the product. - PC-SSD-P Series is limited in the number of cycles they can be written (rewritten) to due to the nature of its memory used. Note that the write life depends on the actual operating conditions. - Do not turn off the power during disk access (writing). Doing so may break the data. - The product comes with a protective function that prevents the disk from damaging during an instantaneous stop but this function is not designed to protect data written onto the disk. When protecting data, use it under the condition which has no instantaneously stops. - This product is not formatted. Please be sure to format before use. FCC PART15 Class B Notice NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/tv technician for help. WARNING TO USER Changes or modifications not expressly approved the manufacturer can void the user s authority to operate this equipment. PC-SSD-P Series 2

3 Features - Containing no rotating or moving part as in hard disk drives, thus best suited for applications which require high environmental resistance (to temperature, humidity, vibration, shock) and for continuous operation for extended periods of time. - Never making any sound such as motor rotation sound or access noise during seeking, thus best suited for applications which require complete silence. - Using SLC (Single Level Cell) NAND flash memory provides reliability and writing speed as well as write endurance that are superior to those of MLC (Multi Level Cell), making it suitable for industrial applications. - By eliminating a rotating or moving part, power consumption is reduced to approximately 1/3 *1 of that of hard disk drive - Normalizing the number of rewriting for all areas to reduce the unevenness so that long life is attained. - When turning off the power during data writing, the power supply is retained for several milliseconds by the internal power protection circuit, resulting in strong resistance against power shutoff. - 8-bit correction/512 bytes error correction feature ensures high data reliability. - Auto recovery feature ensures automated data recovery from data errors that occurs with repeated reading. - S.M.A.R.T. (Self-Monitoring Analysis and Reporting Technology) is supported, making it possible to know the current number of write cycles. *1: PC-HDD40S: Comparison with 1900mW at read/write 3 PC-SSD-P Series

4 Hardware Specifications Item Specifications PC-SSD1000P PC-SSD2000P PC-SSD4000P PC-SSD8000P Memory LBA 960MB 1920MB 3840MB 7680MB capacity CHS 959MB 1919MB 3839MB 7679MB Bus specification ATA (IDE-AT 44 pin) Read 24MByte/sec 40MByte/sec Write 8MByte/sec 15MByte/sec Transfer mode PIO mode 4, Multiword DMA mode 2, Ultra DMA mode 6 NAND Flash memory life span 100,000 cycles Write endurance *1 192,000,000 cycles 384,000,000 cycles Rated voltage 5VDC ±10% Consumed power Sleep 50mW (Typ.) (read) / (write) 650mW (Max.) / 650mW (Max.) Ambient temperature (Operation, Storage) ºC Storage temperature (Operation) 0-90%RH (No condensation) Corrosive gases None Vibration (Operation) 15G or less Shock (Non operation) 1500G or less Physical dimensions (mm) 69.85(W) x 100(D) x 9.50(H) Weight About 65g *1 Refers to the allowed number of write cycles when rewriting under 512KB 768,000,000 cycles 1,536,000,000 cycles BIOS Setup Parameters IDE Parameters Products Size (MB) Cylinder Head Sector PC-SSD1000P PC-SSD2000P PC-SSD4000P PC-SSD8000P PC-SSD-P Series 4

5 About write endurance PC-SSD-P series have a write endurance which limits the number of cycles each memory may be written, due to the characteristic of the memory that is used. Write endurance can be calculated by the following formula as a reference value: Write endurance (cycles) = Total capacity (MB) x 100,000 (cycles) / Size of file (MB) Example1: When the file of 1MB is made for PC-SSD-2000P, and it rewrites it once a second. Write endurance = 1920MB x 100,000 cycles / 1MB = 192,000,000 (cycles) Longevity = 192,000,000 / (3600 x 24 x 365) 6 (year) After all these are reference values, confirm its life span by the following S.M.A.R.T. About S.M.A.R.T. A self-diagnosis program "SMART" that can obtain the S.M.A.R.T information in a SSD is available for download at TDK website. Following information can be obtained using this program: 1. Number of flash memory chips mounted inside SSD, and the total number of blocks 2. Total number of write cycles on SSD 3. Number of write cycles of the block where rewriting occurs most frequently 4. Number of write cycles of the block where rewriting occurs least frequently 5. Number of write cycles of all the blocks (10 step histogram) The NAND type flash memory s life span is 100,000 cycles. The number of write cycles for each block can be determined, making it possible to predict life span. TDK website: At the SMART program download destination: Requirement for SMART program: Windows 2000/XP with VB6.0 runtime and MSFLXGRD.OCX component (such as vb6rt330.exe) 5 PC-SSD-P Series

6 External Dimensions and Master / Slave Settings Connector Pin Assignment Pin Signal Function I/O Pin Signal Function I/O 1 RESET- Bus Reset I 2 GND Signal Ground 3 DB7 Data Bus Bit 7 I/O 4 DB8 Data Bus Bit 8 I/O 5 DB6 Data Bus Bit 6 I/O 6 DB9 Data Bus Bit 9 I/O 7 DB5 Data Bus Bit 5 I/O 8 DB10 Data Bus Bit 10 I/O 9 DB4 Data Bus Bit 4 I/O 10 DB11 Data Bus Bit 11 I/O 11 DB3 Data Bus Bit 3 I/O 12 DB12 Data Bus Bit 12 I/O 13 DB2 Data Bus Bit 2 I/O 14 DB13 Data Bus Bit 13 I/O 15 DB1 Data Bus Bit 1 I/O 16 DB14 Data Bus Bit 14 I/O 17 DB0 Data Bus Bit 0 I/O 18 DB15 Data Bus Bit 15 I/O 19 GND Signal Ground I/O 20 KEY Key Pin 21 DMAREG DMA Request O 22 GND Signal Ground 23 IOW- Host I/O Write I 24 GND Signal Ground 25 IOR- Host I/O Read I 26 GND Signal Ground 27 IORDY I/O ch RDY O 28 Reserved 29 DMAACK DMA Acknowledge I 30 GND Signal Ground 31 INTRQ+ Interrupt Request O 32 IOCS16- Drive 16 Bit I/O O 33 ADD1 Host Address 1 I 34 PDIAG- Passed Diagnostic I/O 35 ADD0 Host Address 0 I 36 ADD2 Host Address 2 I 37 CS0- Chip Select 0 I 38 CS1- Chip Select 1 I 39 DASP- Active (LED) O 40 GND Signal Ground 41 +5V +5VDC 42 +5V +5VDC 43 GND Signal Ground 44 N.C. PC-SSD-P Series 6

7 Limited One-Year Warranty CONTEC Products are warranted by CONTEC CO., LTD to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser. Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from which it was purchased. This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original boards. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy. How to Obtain Service For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you purchased before returning any product. * No product will be accepted by CONTEC group without the RMA number. Liability The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage, misuse, or malfunction of this device. 7 PC-SSD-P Series

8 Copyright 2013 CONTEC CO., LTD. ALL RIGHTS RESERVED. CONTEC CO., LTD. February 2013 Edition , Himesato, Nishiyodogawa-ku, Osaka , Japan Japanese English NA00244 (LYKT052) Chinese _rev2 [ ] No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD.