RWS-858 All-in-one LCD Workstation User Manual.

Transcription

1 RWS-858 All-in-one LCD Workstation User Manual

2 Contents Chapter1 Product Introduction Overview Specification Packing List...2 Chapter2 Installation Instructions Install FDD/HDD Install CD-ROM/Motherboard Connect VGA Adapter Cable Starting Up Replace Filter Cotton Power Cable Connection(factory setting: cables connected) Motherboard Wiring Layout...8 Chapter 3 Structure View...9 Chapter 4 Cautions...10

3 Chapter 1 Product Introduction 1.1 Overview RWS-858 is an industrial Workstation with 10-slot expansion capability. Featuring a 15 detachable display module, the RWS-858 has a rugged yet flexible design for factory floor application. Its 15" high-brightness TFT LCD fulfills the needs for large information view. With 72 functional keypads & touch pad feature, an additional KB or MS is not needed for operation. The standard 8U size can easily be installed in either racks or mounted in panel. Designed with 8U Zinc-plated Chassis and Aluminum Alloy Front Panel, it combines the advantages of PPC, membrane keyboard, touchpad, industrial backplane and industrial power supply (standard configuration: NORCO-10P7 backplane & 300W industrial power supply, optional backplane NORCO-11P4 NORCO-09P6/NORCO-08P4) to form an industrial workstation for various industrial applications featuring low power, low radiation, interference-resistant, mag-electro compatibility, light-weight and easy to maintain. 1.2 Specifications Basic Features: 1. 8U Zinc-plated Chassis and duralumin sand blasting panel XGA (1024 X 768) Color TFT LCD functional keypads & touch pad 4. Disk Drive Bay for CD-ROM, Slim Floppy Disk Drive and 2x3.5 Hard Disk Drive 5. Standard configuration with NORCO-10P7 backplane provides 1x PCI card slot, 2x ISA, 7x PCI slot, dual USB ports 6. 1x 12cm hi-speed dual ball cooling fan 7. Design with hinged front lockable door for easy access 8. Dimension:(W x D x H)483mm x248.6mm x 354m 9. Standard ATX power supply 10.Color: Black 11.Weight:16/20Kgs Standard Configuration: 1. 10P7 backplane 2. ATX-300W Power Supply TFT LCD 1

4 1.3 Packing List User Manual Power Cables Standard CD-ROM screws & Floppy screws(m3*6,14pcs) Hard Disc Screws(1/8*6 screws,6pcs) VGA adapter cable (standard component,1pcs) Spare Sunk Screw(M4*8, 4pcs) Pan Head Screw(M3*6,6pcs) Spare inlet air filter cotton( , 1pcs) 2

5 Chapter 2 Installation Instructions 2.1 Install FDD/HDD 1. Loose the screws on the chassis rear panel to dismount the rear cover. Then loose two M3 screws and pull backward to remove the floppy drive and hard drive bays. 手拧钉 软驱螺钉 ) (remove back cover) (remove FDD/HDD bay) 2. Take out the floppy drive frame and put the floppy drive in it, then fix the floppy drive and floppy drive frame with M3 screws and push forward to tighten the screws. Put hard disc in the HDD bay and fix them with screws. Connect the data cable and power cable with FDD and HDD. 装硬盘螺钉位 装软驱螺钉位 3

6 2.2 Install CD-ROM & Motherboard 1. Loose the beam screws and remove the beam. Then loose M4 & M3 CD-ROM screws and pull backward to remove the CD-ROM frame. 压梁螺钉压梁螺钉光驱螺钉 (Remove CD-ROM frame) 2. Put the CD-ROM into CD-ROM frame and use M3 screws to fix the CD-ROM and its frame. Push forward and tighten the screws. Then install the CD-ROM frame into the chassis and push forward, finally use M3 and M4 screws to fix them. (Remove the beam when installing expansion cards). Tighten the M3 beam screws to mount the beam. Finally, connect data cable and power cable with the CD-ROM. (install CD-ROM) 4

7 3. Loose baffle screws to remove the baffle. Hold the baffle and insert it into the slot on backplane. Then install the motherboard according to the motherboard instructions. 板卡 (install motherboard) 2.3 Install VGA Adapter Cable Take out the VGA Adapter Cable from the accessory kit box and use it to connect the motherboard and the VGA display and tighten the screws. 板卡 显示屏 座 座 板卡 VGA 转接线 (connect VGA adapter cable) 5

8 2.4 Starting Up 1. Unlock and open the front door. Then you can see the black ATX Power switch, the reset switch (red) and dual USB sockets. 2. Turn on the black POWER switch and also turn on the reset switch, then the system starts up. 2.5 Replace Filter Cotton 1. Replace the filter cotton regularly based on different working environments.(recommended once every half-year) 2.Filter cotton can be stored for later use after cleaning it(accessory kit box contains filter cotton) 3. Replace filter cotton: loose filter plate screws and remove the filter plate, then replace the filter cotton. ( 滤网板 ) 螺钉 6

9 2.6 Power Cable Connection(factory setting: cables connected) 7

10 2.7 Motherboard Cables Layout Note: This type of RWS-858 doesn t have a motherboard. Following picture takes NORCO-860 board as an example. For different board choice, the wiring/ cables connection is different. For details, please refer to the user manual of the board you select. 硬盘示灯复位键 ) 电源开关 ) 电源指示灯 KB( 触摸键盘插座 ) MS( 触摸鼠标插座 ) ( 插座 ) 底板 (6 插座 ) 8

11 Chapter 3 Structure View RWS-858 Internal View 9

12 Chapter 4 Cautions 1. To optimize system performance, please do not attempt to connect/disconnect the display screen cables, touch keyboard (Control Panel) by yourself. 2. Select different data cable and power cable as per the motherboard specification. Please refer to the Motherboard Cables Layout in this manual. 3. Touch screen is selectable. Users can select touch screen for this machine based on their actual needs. 10