MOXA C101 Synchronous Interface
|
|
|
- Muriel Williamson
- 6 years ago
- Views:
Transcription
1 MOXA C101 Synchronous Interface Document revision 1.3 (February 6, 2008, 2:58 GMT) This document applies to V3.0 Table of Contents Table of Contents General Information Summary Specifications Additional Documents Synchronous Interface Configuration Property Notes Example Troubleshooting Synchronous Link Application Examples MikroTik Router to MikroTik Router MikroTik Router to Cisco Router General Information Summary Specifications Packages required: synchronous License required: level4 Home menu level: /interface moxa-c101 Standards and Technologies: Cisco/HDLC-X.25 (RFC 1356), Frame Relay (RFC1490), PPP (RFC-1661), PPP (RFC-1662) Hardware usage: Not significant Page 1 of 7
2 MOXA C101 PCI variant cabling DB25f Signal Direction V.35m 4 RTS OUT C 5 CTS IN D 6 DSR IN E 7 GND - B 8 DCD IN F 10 TxDB OUT S 11 TxDA OUT P 12 RxDB IN T 13 RxDA IN R 14 TxCB IN AA 16 TxCA IN Y 20 DTR OUT H 22 RxCB IN X 23 RxCA IN V short 9 and 25 pin Additional Documents Synchronous Interface Configuration Home menu level: /interface moxa-c101 Property cisco-hdlc-keepalive-interval (time; default: 10s) - keepalive period in seconds clock-rate (integer; default: 64000) - speed of internal clock Page 2 of 7
3 clock-source (external internal tx-from-rx tx-internal; default: external) - clock source frame-relay-dce (yes no; default: no) - operate or not in DCE mode frame-relay-lmi-type (ansi ccitt; default: ansi) - Frame-relay Local Management Interface type: ansi - set LMI type to ANSI-617d (also known as Annex A) ccitt - set LMI type to CCITT Q933a (also known as Annex A) ignore-dcd (yes no; default: no) - ignore or not DCD line-protocol (cisco-hdlc frame-relay sync-ppp; default: sync-ppp) - line protocol name mtu (integer; default: 1500) - Maximum Transmit Unit name (name; default: moxa-c101-n) - interface name Notes Example [admin@mikrotik] interface> moxa-c101 [admin@mikrotik] interface moxa-c101> print Flags: X - disabled, R - running 0 R name="moxa-c101-1" mtu=1500 line-protocol=sync-ppp clock-rate=64000 clock-source=external frame-relay-lmi-type=ansi frame-relay-dce=no cisco-hdlc-keepalive-interval=10s ignore-dcd=no [admin@mikrotik] interface moxa-c101> [admin@mikrotik] interface moxa-c101> monitor 0 dtr: yes rts: yes cts: no dsr: no dcd: no [admin@mikrotik] interface moxa-c101> [admin@mikrotik] interface moxa-c101> monitor 0 dtr: yes rts: yes cts: yes dsr: yes dcd: yes [admin@mikrotik] interface moxa-c101> Troubleshooting Page 3 of 7
4 Synchronous Link Application Examples MikroTik Router to MikroTik Router Page 4 of 7
5 ip address> add address= /32 interface=wan \ \... network= broadcast= [admin@mikrotik] ip address> print Flags: X - disabled, I - invalid, D - dynamic # ADDRESS NETWORK BROADCAST INTERFACE / ether / ether / wan [admin@mikrotik] ip address> /ping byte ping: ttl=255 time=31 ms 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 26/27.6/31 ms [admin@mikrotik] ip address> [admin@mikrotik] ip route> add gateway [admin@mikrotik] ip route> print Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit # DST-ADDRESS PREF-SRC G GATEWAY DISTANCE INTER... 0 A S /0 r wan 1 ADC / r 0 ether2 2 ADC / r 0 ether1 3 ADC / r 0 wan [admin@mikrotik] ip route> [admin@mikrotik] ip address> add address= /32 interface=moxa \ \... network= broadcast= [admin@mikrotik] ip address> print Flags: X - disabled, I - invalid, D - dynamic # ADDRESS NETWORK BROADCAST INTERFACE / Public / moxa [admin@mikrotik] ip address> /ping byte ping: ttl=255 time=31 ms byte ping: ttl=255 time=26 ms byte ping: ttl=255 time=26 ms 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 26/27.6/31 ms [admin@mikrotik] ip address> MikroTik Router to Cisco Router Page 5 of 7
6 ip address> add address /32 interface wan \ \... network broadcast [admin@mikrotik] ip address> print Flags: X - disabled, I - invalid, D - dynamic # ADDRESS NETWORK BROADCAST INTERFACE / ether / ether / wan [admin@mikrotik] ip address> /ping byte ping: ttl=255 time=31 ms 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 26/27.6/31 ms [admin@mikrotik] ip address> [admin@mikrotik] ip route> add gateway [admin@mikrotik] ip route> print Flags: X - disabled, A - active, D - dynamic, Page 6 of 7
7 C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit # DST-ADDRESS PREF-SRC G GATEWAY DISTANCE INTER... 0 A S /0 r wan 1 ADC / r 0 ether2 2 ADC / r 0 ether1 3 ADC / r 0 wan [admin@mikrotik] ip route> CISCO#show running-config Building configuration... Current configuration:... interface Ethernet0 description connected to EthernetLAN ip address interface Serial0 description connected to MikroTik ip address serial restart-delay 1 ip classless ip route end CISCO# CISCO#ping Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 28/32/40 ms CISCO# Page 7 of 7
MOXA C101 Synchronous Interface
MOXA C101 Synchronous Interface Document revision 1.1 (Fri Mar 05 08:15:42 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents General Information Summary Specifications Related
CISCO/Aironet 2.4GHz 11Mbps Wireless Interface
CISCO/Aironet 2.4GHz 11Mbps Wireless Interface Document revision 1.3 (February 6, 2008, 2:56 GMT) This document applies to V3.0 Table of Contents Table of Contents Summary Specifications Additional Documents
RIP. Table of Contents. General Information. Summary. Specifications
RIP Document revision 1 (Wed Mar 24 12:32:12 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents General Information Summary Specifications Related Documents Additional Documents
C101 ISA/PCI SuperSync Board
C101 ISA/PCI SuperSync Board User s Manual Fifth Edition, June 2008 www.moxa.com/product 2008 Moxa Inc., all rights reserved. Reproduction without permission is prohibited. C101 ISA/PCI SuperSync Board
Netopia R7100 Application Note Part Number
Netopia R7100 Application Note Part Number 6190003-00-01 Copper Edge 200 and Cisco Configuration Using RFC1483 via V.35 Written by: Ryan Eccles Date: 12/17/99 Revised: None This application note describes
Chapter 7 Lab 7-2, Using the AS_PATH Attribute
Chapter 7 Topology Objectives Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use the AS_PATH attribute to filter BGP routes based on their source AS numbers.
GRE Tunnel with VRF Configuration Example
GRE Tunnel with VRF Configuration Example Document ID: 46252 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Caveats
Lab 3.5.1: Basic Frame Relay
Lab 3.5.1: Basic Frame Relay Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 R2 Default Gateway Fa0/0 192.168.10.1 255.255.255.0 N/A S0/0/1 10.1.1.1 255.255.255.252 N/A S0/0/1
Configuring and Troubleshooting Frame Relay
Configuring and Troubleshooting Frame Relay Document ID: 16563 Interactive: This document offers customized analysis of your Cisco device. Contents Introduction Before You Begin Conventions Prerequisites
Cisco Configuring and Troubleshooting Frame Relay
Table of Contents Configuring and Troubleshooting Frame Relay...1 Related Information...2 Introduction...3 Configuring Basic Frame Relay...6 Introduction...6 Network Diagram...6 Configurations...6 debug
Terminal Console. Table of Contents. General Information. Summary. Specifications. Related Documents. Summary Specifications
Terminal Console Document revision NaN (Tue Apr 20 16:17:53 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents Summary Specifications Related Documents Common Console Functions
Configuring the 4-Port Serial Interface SPA
This chapter provides information about configuring the 4-Port Serial Interface SPA on Cisco ASR 1000 Series Routers. Configuration Tasks, page 1 Verifying the Interface Configuration, page 11 Configuration
Terminal Console. Table of Contents. General Information. Summary. Specifications. Related Documents. Summary Specifications
Terminal Console Document revision 1.0 (Mon Nov 8 13:15:54 GMT 2004) This document applies to V2.9 Table of Contents Table of Contents Summary Specifications Related Documents Common Console Functions
Chapter 7 Lab 7-1, Configuring BGP with Default Routing
Chapter 7 Topology Objectives Configure BGP to exchange routing information with two ISPs. Background The International Travel Agency (ITA) relies extensively on the Internet for sales. For this reason,
Packet Tracer - Connect a Router to a LAN (Instructor Version)
(Instructor Version) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Device Interface IP Address Subnet Mask Default
Distance vector Routing protocols. 2000, Cisco Systems, Inc. 9-1
Distance vector Routing protocols 2000, Cisco Systems, Inc. 9-1 IP Routing Configuration Tasks Router configuration Select routing protocols Specify networks or interfaces RIP Network 172.16.0.0 IGRP,
Implement Static Routes for IPv6 Configuration Example
Implement Static Routes for IPv6 Configuration Example Document ID: 113361 Contents Introduction Prerequisites Components Used Conventions Configure Network Diagram Configurations Verify Related Information
Case Study 2: Frame Relay and OSPF Solution
Case Study 2: Frame Relay and OSPF Solution Objective In this case study, you troubleshoot a complex scenario involving Frame Relay and Open Shortest Path First (OSPF). Figure 2-1 shows the topology for
EIGRP Lab / lo1. .1 lo / /30
EIGRP Lab 172,16,1.0/24.1 lo1 192.168.20.0/30.2.1 Merida fa0 fa0 Vargas lo2.1 lo2.5.1 lo1 192.168.30.0/24 172.16.2.0/24 192.168.20.4.0/30 Scenario: Loopback0 is used for RouterID Loopback1 is a virtual
The information in this document is based on Cisco IOS Software Release 15.4 version.
Contents Introduction Prerequisites Requirements Components Used Background Information Configure Network Diagram Relevant Configuration Verify Test case 1 Test case 2 Test case 3 Troubleshoot Introduction
Cisco Configuring Hub and Spoke Frame Relay
Table of Contents Configuring Hub and Spoke Frame Relay...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...1 Network Diagram...2 Configurations...2
Lab Configuring and Verifying Standard IPv4 ACLs Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
Configuration and Management of Networks
Configuring BGP using the AS_PATH attribute Topology Objectives Background Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use the AS_PATH attribute to filter
Lab Troubleshooting Using traceroute Instructor Version 2500
Lab 9.3.4 Troubleshooting Using traceroute Instructor Version 2500 294-833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 9.3.4 Copyright 2003, Cisco Systems, Inc. Objective Use the traceroute Cisco IOS
Management IP Interface
The management interface is used for the video control plane messages, such as session creation and deletion, between the Logical Edge Devices (LED) and the external Edge Resource Manager (ERM) server.
Basic Router Configuration
This section includes information about some basic router configuration, and contains the following sections: Default Configuration, on page 1 Configuring Global Parameters, on page 2 Configuring Gigabit
Lab Configuring and Verifying Standard ACLs Topology
Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 9 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
3 ROUTER SETUP WITH FRAME RELAY CONFIGURATION OF FRAME RELAY ROUTER
3 ROUTER SETUP WITH FRAME RELAY R2 s0 Network 192.168.1.0 s1 DCE * Frame Relay Network * s0 192.168.1.0 s0 DCE R1 Hardware Requirement: 1 Router with t 2 Serials 2 Router with 1 Serial 2 DTE/DCE Serial
RealCiscoLAB.com. Chapter 6 Lab 6-2, Using the AS_PATH Attribute. Topology. Objectives. Background. CCNPv6 ROUTE
RealCiscoLAB.com CCNPv6 ROUTE Chapter 6 Lab 6-2, Using the AS_PATH Attribute Topology Objectives Background Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use
IPv6 Tunnel through an IPv4 Network
IPv6 Tunnel through an IPv4 Network Document ID: 25156 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations (Manual IPv6 Mode) Configurations
L2TP Interface. Table of Contents. General Information. Summary
L2TP Interface Document revision 1.1 (Fri Mar 05 08:26:01 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents General Information Summary Quick Setup Guide Specifications Related
Building the Routing Table. Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles
Building the Routing Table Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles Introducing the Routing Table R1# show ip route Codes: C - connected,
Configuration and Management of Networks 2012
Configuring BGP with default routing Topology Objectives Background Instructions Configure BGP to exchange routing information with two ISPs. The International Travel Agency (ITA) relies extensively on
Cisco Back to Back Frame Relay
Table of Contents Back to Back Frame Relay...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...2 Network Diagram...2 Configurations...2 Verify...3
UNC20 Module. User's Manual. D Breisach, Germany D Breisach, Germany Fax +49 (7667)
UNC20 Module User's Manual P.O: Box 1103 Kueferstrasse 8 Tel. +49 (7667) 908-0 sales@fsforth.de D-79200 Breisach, Germany D-79206 Breisach, Germany Fax +49 (7667) 908-200 http://www.fsforth.de Copyright
MPLS Point-to-Multipoint Traffic Engineering Support for Static Pseudowires
MPLS Point-to-Multipoint Traffic Engineering Support for Static Pseudowires The MPLS Point-to-Multipoint Traffic Engineering: Support for Static Pseudowires feature allows you to configure a point-to-multipoint
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Layer3 VPN with OSPF Protocol between CE-PE
MPLS Layer3 VPN with OSPF Protocol between CE-PE Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made
This chapter covers the following subjects:
This chapter covers the following subjects: Configuring and Testing Static Routes Distance Vector Concepts Configuring RIP and IGRP C H A P T E R 5 RIP, IGRP, and Static Route Concepts and Configuration
(ICMP), RFC
Internet et Control o Message Protocol (ICMP), RFC 792 http://icourse.cuc.edu.cn/networkprogramming/ linwei@cuc.edu.cn Nov. 2009 Overview The IP (Internet Protocol) relies on several other protocols to
RealCiscoLAB.com. Chapter 6 Lab 6-1, Configuring BGP with Default Routing. Configure BGP to exchange routing information with two ISPs.
RealCiscoLAB.com CCNPv6 ROUTE Chapter 6 Lab 6-1, Configuring BGP with Default Routing Topology Objectives Background Configure BGP to exchange routing information with two ISPs. The International Travel
Table of Contents 1 System Maintaining and Debugging Commands 1-1
Table of Contents 1 System Maintaining and Debugging Commands 1-1 System Maintaining Commands 1-1 ping 1-1 tracert 1-4 System Debugging Commands 1-6 debugging 1-6 display debugging 1-7 i 1 System Maintaining
Internet Control Message Protocol (ICMP), RFC 792. Prof. Lin Weiguo Copyleft 2009~2017, School of Computing, CUC
Internet Control Message Protocol (ICMP), RFC 79 Prof Lin Weiguo Copyleft 009~07, School of Computing, CUC Oct 07 Overview } The IP (Internet Protocol) relies on several other protocols to perform necessary
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Topology Objectives Configure EIGRP for IPv4. Create a 6to4 tunnel. Configure static IPv6 routes. Background In this lab, you configure EIGRP for full connectivity
Adapted from the Synchronization example in g/case/studies/icsbgp4.html
Adapted from the Synchronization example in http://www.cisco.com/en/us/docs/internetworkin g/case/studies/icsbgp4.html When an AS provides transit service to other ASs when there are non-bgp routers in
Chapter 6: Network Layer
Chapter 6: Network Layer Introduction to Networks Intro to Networks v5 Network Layer Intro to Networks v5 2 The Network Layer End to End Transport processes Addressing end devices Encapsulation of Packets
Lab 4.2.5a Connectivity Tests Ping
Lab 4.2.5a Connectivity Tests Ping Objective Use the ping command to send ICMP datagrams to target host. Verify that the network layer between source and destination is working properly. Retrieve information
Chapter 6 Lab 6-3, Configuring IBGP and EBGP Sessions, Local Preference, and MED
Chapter 6 Lab 6-3, Configuring IBGP and EBGP Sessions, Local Preference, and MED Topology Objectives Background For IBGP peers to correctly exchange routing information, use the next-hop-self command with
LAB 5: DMVPN BGP. LAB 5: Diagram. Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M.
LAB 5: DMVPN BGP LAB 5: Diagram Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M. LAB 5: Configure BGP over DMVPN Configuration Step 1: Enable loopback and physical interfaces
Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Table of Contents 1 System Maintaining and Debugging 1-1
Table of Contents 1 System Maintaining and Debugging 1-1 System Maintaining and Debugging 1-1 Ping 1-1 Introduction 1-1 Configuring Ping 1-1 Ping Configuration Example 1-2 Tracert 1-4 Introduction 1-4
Troubleshooting LSP Failure in MPLS VPN
Troubleshooting LSP Failure in MPLS VPN Document ID: 23565 Contents Introduction Prerequisites Requirements Components Used Conventions Network Diagram Router Configurations Problem Cause of the LSP Failure
Cisco Interconnecting Cisco Networking Devices Part 2
Cisco 200-105 Interconnecting Cisco Networking Devices Part 2 R1# show running-config description ***Loopback*** ip address 192.168.1.1 255.255.255.255 Question: 374 description **Connected to R1-LAN**
Chapter 1 Frame Relay Configuration and Management
Chapter 1 Frame Relay Configuration and Management 1 This chapter describes the configuration tasks for the Cisco frame relay packet-switched software. You will find the following information in this chapter:
Table of Contents 1 System Maintenance and Debugging Commands 1-1
Table of Contents 1 System Maintenance and Debugging Commands 1-1 System Maintenance Commands 1-1 ping 1-1 ping ipv6 1-5 tracert 1-6 tracert ipv6 1-7 System Debugging Commands 1-8 debugging 1-8 display
Easy Virtual Network Configuration Example
Easy Virtual Network Configuration Example Document ID: 117974 Contributed by Fabrice Ducomble, Cisco TAC Engineer. Aug 04, 2014 Contents Introduction Prerequisites Requirements Components Used Background
TS Open Day Data Center Fibre Channel over IP
TS Open Day Data Center Fibre Channel over IP Presented by: Rong Cheng- TAC LAN & DCN China Jan 30 th, 2015 2013 Cisco and/or its affiliates. All rights reserved. 1 FCIP Introduction FCIP Configuration
CS 356: Computer Network Architectures. Lecture 10: IP Fragmentation, ARP, and ICMP. Xiaowei Yang
CS 356: Computer Network Architectures Lecture 10: IP Fragmentation, ARP, and ICMP Xiaowei Yang xwy@cs.duke.edu Overview Homework 2-dimension parity IP fragmentation ARP ICMP Fragmentation and Reassembly
Contents. Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9
Contents Ping, tracert, and system debugging commands 1 debugging 1 display debugging 2 ping 2 ping ipv6 5 tracert 7 tracert ipv6 9 i Ping, tracert, and system debugging commands debugging Syntax Default
Application Notes for ADTRAN NetVanta 3205 Access Router and IP Office Using Frame Relay over T1 - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for ADTRAN NetVanta 3205 Access Router and IP Office Using Frame Relay over T1 - Issue 1.0 Abstract These Application Notes describe a sample
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration Topology Objectives Configure IPv6 addressing. Configure and verify RIPng on R1 and R2. Configure IPv6 static routes between R2 and R3.
Lab - Troubleshooting Connectivity Issues
Lab - Troubleshooting Connectivity Issues Topology Addressing Table R1 ISP Objectives Device Interface IP Address Subnet Mask Default Gateway G0/1 192.168.1.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252
I Commands. iping, page 2 iping6, page 4 itraceroute, page 5 itraceroute6 vrf, page 6. itraceroute vrf encap vxlan, page 12
iping, page 2 iping6, page 4 itraceroute, page 5 itraceroute6 vrf, page 6 itraceroute6 vrf encap vlan, page 7 itraceroute6 vrf encap vxlan dst-mac, page 8 itraceroute vrf, page 9 itraceroute vrf encap
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
LAB5: OSPF IPv4. OSPF: Stub. Disclaimer
Page1 LAB5: SPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Using an ADTRAN Terminal Adapter with Cisco Routers
Using an ADTRAN Terminal Adapter with Cisco Routers Document ID: 28080 Contents Introduction Prerequisites Requirements Components Used Conventions Dialing Method V.25 or V.25bis Dialing DTR Dialing Keypad
Configuring GRE Tunnel Over Cable
Configuring GRE Tunnel Over Cable Document ID: 12084 Introduction Before You Begin Conventions Prerequisites Components Used Background Theory Configure Network Diagram Configurations Verify Troubleshoot
Chapter 5: Maintaining and Troubleshooting Routing Solutions
Chapter 5: Maintaining and Troubleshooting Routing Solutions CCNP TSHOOT: Maintaining and Troubleshooting IP Networks Course v6 1 Troubleshooting Network Layer Connectivity 2 Routing and Routing Data Structures
Using the Management Ethernet Interface
The Cisco ASR 920 Series Router has one Gigabit Ethernet Management Ethernet interface on each Route Switch Processor. The purpose of this interface is to allow users to perform management tasks on the
2016 Braindump2go Valid Cisco Exam Preparation Materials:
Guarantee All Exams 100% Pass One Time 2016 NEW Cisco CCNA Routing and Switching 200-105: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Exam Questions and Answers RELEASED in Braindump2go.com
Lab Configuring ISDN Dial Backup
Lab 8.7.1 Configuring ISDN Dial Backup Objective Configure ISDN dial backup for a fixed Frame Relay WAN link. Scenario The network engineer for the International Travel Agency (ITA) is responsible for
Chapter 4: outline. 4.5 routing algorithms link state distance vector hierarchical routing. 4.6 routing in the Internet RIP OSPF BGP
Chapter 4: outline 4.1 introduction 4.2 virtual circuit and datagram networks 4.3 what s inside a router 4.4 IP: Internet Protocol datagram format IPv4 addressing ICMP 4.5 routing algorithms link state
Vorlesung Kommunikationsnetze
Picture 15 13 Vorlesung Kommunikationsnetze Prof. Dr. H. P. Großmann mit B. Wiegel sowie A. Schmeiser und M. Rabel Sommersemester 2009 Institut für Organisation und Management von Informationssystemen
Lab 2.5.1: Basic PPP Configuration Lab
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 R2 R3 Default Gateway Fa0/1 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252 N/A Lo0 209.165.200.225 255.255.255.224
Overview of Keepalive Mechanisms on Cisco IOS
Overview of Keepalive Mechanisms on Cisco IOS Document ID: 118390 Contributed by Atri Basu and Michael Sullenberger, Cisco TAC Engineers. Dec 17, 2014 Contents Introduction Background Information Interface
Configuring IS IS over IPv6
Configuring IS IS over IPv6 Document ID: 40262 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Troubleshooting
IP NAT Troubleshooting. Solutions. Luke Bibby, CCIE #45527
IP NAT Troubleshooting Solutions Luke Bibby, CCIE #45527 Quick Overview of Scenario Solutions Scenario #1 R2 s E0/0 should be NAT inside not NAT outside ACL 100 is configured incorrectly NAT policy missing
CSE/EE 461 The Network Layer. Application Presentation Session Transport Network Data Link Physical
CSE/EE 461 The Network Layer Application Presentation Session Transport Network Data Link Physical This Lecture Focus: What to do when one wire isn t big enough? Point to point link Broadcast link (Ethernet
RealCiscoLAB.com. Chapter 2 Lab 2-2, EIGRP Load Balancing. Topology. Objectives. Background. CCNPv6 ROUTE
RealCiscoLAB.com CCNPv6 ROUTE Chapter 2 Lab 2-2, EIGRP Load Balancing Topology Objectives Background Review a basic EIGRP configuration. Explore the EIGRP topology table. Identify successors, feasible
CCNP ROUTE 6.0 Student Lab Manual
CCNP ROUTE 6.0 Student Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors
The Access Tier ISP, considering upstream connectivity
College of Engineering, Design, Art and Technology Makerere University The Access Tier, considering upstream connectivity / Diarmuid O Briain GameCORE / netlabs!ug 30 January 2018 MikroTik MUM, The Access,
IP - The Internet Protocol. Based on the slides of Dr. Jorg Liebeherr, University of Virginia
IP - The Internet Protocol Based on the slides of Dr. Jorg Liebeherr, University of Virginia Orientation IP (Internet Protocol) is a Network Layer Protocol. IP: The waist of the hourglass IP is the waist
Configuring MLPPP. Finding Feature Information
The Multilink Point-to-Point (MLPPP) feature provides load balancing functionality over multiple WAN links, while providing multivendor interoperability, packet fragmentation and proper sequencing, and
MPLS Troubleshooting. Contents. Prerequisites. Document ID: Requirements. Components Used
MPLS Troubleshooting Document ID: 12492 ontents Introduction Prerequisites Requirements omponents Used onventions Troubleshoot Procedures Verify That Routing Protocol Runs Verify EF Switching Verify MPLS
ICMP (Internet Control Message Protocol)
Today s Lecture ICMP (Internet Control Message Protocol) Internet Protocols CSC / C 573 I. ICMP Overview II. ICMP rror Reporting III. ICMP Query / Response Messages IV. ICMP Message Processing Fall, 2005
IP MultiLayer Switching Sample Configuration
IP MultiLayer Switching Sample Configuration Document ID: 12022 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Network Diagram MLS Operation
South America Workshop WALC 2006 (Quito, Ecuador July 06) Router Configuration #2 (continued)
South America Workshop WALC 2006 (Quito, Ecuador 26-28 July 06) Router Configuration #2 (continued) Miguel Baptista (miguel.baptista@fccn.pt) Pedro Lorga (lorga@fccn.pt) Simon Muyal (muyal@renater.pt)
ROUTER COMMANDS. BANNER: Config# banner motd # TYPE MESSAGE HERE # - # can be substituted for any character, must start and finish the message
ROUTER COMMANDS TERMINAL CONTROLS: Config# terminal editing - allows for enhanced editing commands Config# terminal monitor - shows output on telnet session Config# terminal ip netmask-format hexadecimal
Layer3 VPN with RIP protocol between CE-PE
MPLS Layer3 VPN with IP protocol between E-PE Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to
Lab 4-3a Configuring IS-IS over Frame Relay: Router Used As Frame Switch
Lab 4-3a Configuring IS-IS over Frame Relay: Router Used As Frame Switch Learning Objectives Configure and verify Frame Relay point-to-point subinterfaces Configure and verify the operation of Integrated
Total Access 600R (P/N L1#TDM) Menu Tree - System Info Branch. Total Access 600R (P/N L1#TDM) Menu Tree - System Utility Branch
Total Access 600R (P/N 4200600L1#TDM) Menu Tree - System Info Branch System Info System Config System Utility Router Modules System Name System Location System Contact Unit Name Part Number Serial Number
Step 2. Manual configuration of global unicast and link-local addresses
Lab: ICMPv6 and ICMPv6 Neighbor Discovery CIS 116 IPv6 Fundamentals Enter your answers to the questions in this lab using Canvas Quiz DHCPv6 Lab. Part 1: Setup Step 1. Basics a. Log into NetLab: ccnp.bayict.cabrillo.edu
DA-820 Series Quick Installation Guide
DA-820 Series Quick Installation Guide x86 Rackmount Embedded Computers Edition 2.0, January 2018 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel:
Exercise Sheet 4. Exercise 1 (Routers, Layer-3-Switches, Gateways)
Exercise Sheet 4 Exercise 1 (Routers, Layer-3-Switches, Gateways) 1. What is the purpose of Routers in computer networks? (Also explain the difference to Layer-3-Switches.) 2. What is the purpose of Layer-3-Switches
Using Serial Ports to Connect to ATM with DXI Encapsulation
Using Serial Ports to Connect to ATM with DXI Encapsulation Document ID: 10418 Contents Introduction Prerequisites Requirements Components Used Conventions Physical Setup ATM DXI Modes ATM DXI Headers
Using the Management Ethernet Interface
This chapter covers the following topics: Gigabit Ethernet Management Interface Overview, page 1 Gigabit Ethernet Port Numbering, page 1 IP Address Handling in ROMmon and the Management Ethernet Port,
Chapter 3: Using Maintenance & Troubleshooting Tools and Applications
Chapter 3: Using Maintenance & Troubleshooting Tools and Applications CCNP TSHOOT: Maintaining and Troubleshooting IP Networks Course v6 1 Chapter 3 Objectives Use Cisco IOS commands to gather information
Application Note. IP Nano (IPn920F & IPn920T) & Centracs Compatibility. February Country Hills Landing NW Calgary, Alberta Canada T3K 5P3
Application Note IP Nano (IPn920F & IPn920T) & Centracs Compatibility February 2013 150 Country Hills Landing NW Calgary, Alberta Canada T3K 5P3 Phone: (403) 248-0028 Fax: (403) 248-2762 www.microhardcorp.com
Juniper Netscreen Security Device. How to Enable IPv6 Page-51
Juniper Netscreen Security Device Page-51 Netscreen Firewall - Interfaces Below is a screen shot for a Netscreen Firewall interface. All interfaces have an IPv6 address except ethernet0/0. We will step
LAB8: OSPF IPv4. OSPF: Virtual Link. Disclaimer
Page1 AB8: OSPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material