MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module

Transcription

1 MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module Function Upgrades (Version 2.1) For MD1230A Data Quality Analyzer MU120111A/MU120112A Features OSPF Protocol (MD1230A-07) OSPF Emulation satisfying the RFC2328 OSPF Version 2 standards can be performed by adding the optional MD1230A-07 OSPF Protocol software. Up to 200 virtual routers can be registered for each physical port and each of Router-LSA, Network-LSA, Summery-LSA, AS-external-LSA, and NSSA External-LSA can be registered for each router. As a result, HELLO packets, Database Description packets, Link- State Request packets, Link-State Update packets and Link- State Acknowledgement packets are all acknowledged (send and receive). Note: DR and BDR operation is not supported. MPLS (LDP/CR-LDP) Protocol (MD1230A-08) LDP and CR-LDP emulation satisfying the RFC3036 and RFC3212 standards can be performed by adding the optional MD1230A-08 MPLS (LDP/CR-LDP) Protocol software. Adjacent LSR detection can be performed using Hello messages, LDP section establishment, and LDP message exchange. Moreover, explicit LSPs can be specified. RFC2889 Benchmarking Test (MD1230A-10) Benchmarking tests of LAN switching devices satisfying the RFC2889 standards can be performed by adding the optional MD1230A-10 RFC2889 Benchmarking Test software. The following tests can be performed. 1) Fully meshed throughput, frame loss and forwarding rates 2) Partially meshed one-to-many/many-to-one 3) Partially meshed multiple devices 4) Partially meshed unidirectional traffic 5) Congestion control 6) Forward pressure and maximum forwarding rate 7) Address caching capacity 8) Address learning rate 9) Errored frames filtering 10) Broadcast frame forwarding and latency MPLS (RSVP) Protocol (MD1230A-09) RSVP and RSVP-TE emulation satisfying the RFC2205 and RFC3209 standards can be performed by adding the optional MD1203A-09 MPLS (RSVP) Protocol software.

2 IPv6 Expansion (Option MD1230A-12) The following functions can be performed by adding the optional MD1230A-12 IPv6 Expansion software. 1) ICMPv6 support 2) MLD (Multicast Listener Discovery) Emulation 3) Ping6 4) RFC2544 test using IPv6 5) IPv6 traffic monitoring and mapping 6) Sending these IPv6 protocols in transmit streams: IPv6 over IPv4 TCP/IPv6 UDP/IPv6 ICMPv6/IPv6 ICMPv6/IPv6 over IPv4 TCP/IPv6 over IPv4 UDP/IPv6 over IPv4 7) IPv6 related counters Send/Receive IPv6 packet count/rate Send/Receive ICMPv6(NA) packet count Send/Receive ICMPv6(NS) packet count Send/Receive ICMPv6 Echo Request packet count Send/Receive ICMPv6 Echo Reply packet count User-defined counter for IPv6 8) Filter and trigger for capture based on IPv6 9) Filter for user-defined counter based on IPv6 Protocol Addition and Expansion The following functions are added or expanded. 1) Advertising 2 32 routes and maintaining 200 BGP Peers in BGP-4 emulation 2) Added IS-IS send and protocol decode functions 3) Added OSPF protocol decode function 4) Added MPLS (LDP/CR-LDP) protocol decode function 5) Added MPLS (RSVP) protocol decode function 6) IPv6 expanded header support for IPv6 send and protocol decode functions Support for 1000BASE-T The new MU120112A Gigabit Ethernet module supports the standard 1000BASE-T copper interface using the G0124A 1000BASE-T GBIC optional accessory. Note: For 1000BASE-T, the wire speed is 1 Gbps full duplex. 1000BASE-T GBIC 2

3 Function Upgrades Monitor Mode Function For network equipment R&D as well as network troubleshooting, it is helpful to use the MD1230A to monitor in-service traffic at full wire speed. Starting in version 2.0, using the new MD1230A monitor mode saves time by avoiding any port settings, so the monitoring is simple and trouble-free. Router Monitor Signal BER Measurement Function The MD1230A has two BER measurement functions that are supported by both Ethernet and POS modules. 1) Unframed BER Test When evaluating the quality of WDM and long-distance lines using a media converter, a bit error rate test is typically used. A PRBS pattern is converted to 8B/10B data and sent without an Ethernet frame (unframed). At the receive side, the PRBS pattern is recovered and the bit error rate is measured. Note: An idle code and start field delimiter are inserted cyclically into the PRBS pattern. When option MD1230A-13 is installed, the MU120118A 10 Gigabit Ethernet module supports a similar function. 8B/10B encoded PRBS pattern MD1230A Service Disruption Time Measurement This function, supported from version 2.0, measures service disruption time by computations based on the frame transmit rate and the relationship between the numbers of received frames vs. sent frames. TCP/UDP Port Increment Function A function for incrementing the port number has been added to the UDP or TCP transmit data stream settings. The destination port number or the source port number can be set to increment automatically. Firewall equipment MD1230A WDM line 2) Packet BER Test (MD1230A-11 option) When measuring the bit error rate of networks using routers and switches, it is necessary to encapsulate the PRBS pattern in an Ethernet frame or IP packet. At the sending side, a PRBS9 pattern can be sent in the data field by selecting the MD1230A Test Frame function. At the receiving side, the MD1230A checks the PRBS pattern in the data and reports the PRBS bit error rate and PRBS error frame rate. A sequence number is included in MD1230A Test Frames, and out of order frames are counted at the receiving side. Incorporating PRBS9 pattern in data field of frames MD1230A UDP port scan test for firewall equipment MD1230A Router, Switch 3

4 Functions Supported by Version 2.1 MU120101A MU120102A MU120103A - Function 10/100M Ethernet Gigabit Ethernet MU120106A Module Module 2.5G/10G Modules MD1230A-07 OSPF Protocol Option MD1230A-08 MPLS (LDP/CR-LDP) Protocol Option MD1230A-09 MPLS (RSVP) Protocol Option MD1230A-10 RFC2889 Benchmarking Test Option X MD1230A-12 IPv6 Expansion Option MD1230A-13 XENPAK Test Option (including unframed BER test) N/A N/A N/A BGP-4 emulation function expansion IS-IS send/protocol decode function X X X Protocol expansion OSPF protocol decode function X X X or addition MPLS (LDP/CR-LDP) protocol decode function X X X MPLS (RSVP) protocol decode function X X X IPv6 expanded header support for IPv6 send and decode functions X X 1000BASE-T support N/A N/A Monitor mode support X X X Service disruption time measurement X X X TCP/UDP port number increment function X X BER measurement X: Supported function N/A: Not applicable Unframed BER test X X MD1230A-11 Packet BER Test Option X X 4

5 MU120111A MU120112A MU120118A Function 10/100M Ethernet Gigabit Ethernet 10 Gigabit Module (New) Module (New) Ethernet Module MD1230A-07 OSPF Protocol Option X X MD1230A-08 MPLS (LDP/CR-LDP) Protocol Option X X MD1230A-09 MPLS (RSVP) Protocol Option X X MD1230A-10 RFC2889 Benchmarking Test Option X X MD1230A-12 IPv6 Expansion Option X X MD1230A-13 XENPAK Test Option (including Unframed BER test) N/A N/A X BGP-4 emulation function expansion X X X IS-IS send / protocol decode function X X X Protocol expansion OSPF protocol decode function X X X or addition MPLS (LDP/CR-LDP) protocol decode function X X X MPLS (RSVP) protocol decode function X X X IPv6 expanded header support for IPv6 send and protocol decode functions X X X 1000BASE-T support N/A X N/A Monitor mode support X X X Service disruption time measurement X X X TCP/UDP port number increment function X X X BER measurement Unframed BER test X X Note 1 MD1230A -11 Packet BER Test Option X X X Note 1: Supported by MD1230A-13 XENPAK Test Option X: Supported function N/A: Not applicable 5

6 Specifications Ports MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module Interface Optical: 1000BASE-SX/LX/LH/ZX 1, Electrical: 1000BASE-T Number of ports: 2 Connector Optical: SC, Electrical: RJ-45 Link speed: 1,000 Mbit/s Duplex mode: Full Negotiation: On/off Flow control: On/off LED Link (10/100M), Tx /Collision, Rx/Error Link, Tx, Rx, Error Connection mode When the mapping is Framed : Normal mode, Through mode, Monitor mode Preamble length: 2 to 255 bytes MAC address: Static, increment, decrement, random (changeable parts specified in 4-bit units) VLAN tag 2 :Static, increment, decrement, random MPLS label 2 : Up to 10 MPLS labels with fixed settings can be appended. Protocol editing: Frame settings IPv4, IPv6, TCP/IPv4, UDP/IPv4, IGMP/IPv4, ICMP/IPv4, RIP/UDP/IPv4, DHCP/UDP/IPv4, IPX, ARP, pause control, IS-IS The following protocols are added by the MD1230A-12 option: TCP/IPv6, UDP/IPv6, ICMPv6/IPv6, IPv6 over IPv4, ICMPv6/IPv6 over IPv4, TCP/IPv6 over IPv4, UDP/IPv6 over IPv4 Data field Can set any 4 parts in data field: All1s, all 0s, alternate1/0 (each bit, each 2 bits, each 4 bits, each byte, each 2 bytes, increment, decrement, random, user programmable, single PRBS9, time stamp, sequence number, test frame) Frame length 18 to 10,000 bytes (settable as auto, fixed, increment, or random) 48 to 65,280 bytes (settable as auto, fixed, increment, or random) Stream settings Interface: 10BASE-T/100BASE-TX Number of ports: 8 Connector: RJ-45 Link speed: 10 Mbit/s, 100 Mbit/s Duplex mode: Full, Half Negotiation: On/off Flow control: On/off Stream transport mode: Continuous, continuous burst, stop after this stream, next stream, jump to stream, jump to stream for count (loop count: 1 to 16,000,000, frame count per burst: 1 to 16,777,215, burst count per stream: 1 to 16,777,215) Interframe gap 10BASE-T: 8,000 ns to 1,700 s, resolution of 800 ns settable as fixed, random 100BASE-TX: 800 ns to 170 s, resolution of 80 ns settable as fixed, random Interburst gap 10BASE-T: 8,000 ns to 1,700 s, resolution of 800 ns settable as fixed, random 100BASE-TX: 800 ns to 170s, resolution of 80 ns settable as fixed, random Interstream gap 10BASE-T: 8,000 ns to 1,700 s, resolution of 800 ns settable as fixed, random 100BASE-TX: 800 ns to 170 s, resolution of 80 ns settable as fixed, random 256 streams/port Stream transport mode: Continuous, continuous burst, stop after this stream, next stream, jump to stream, jump to stream for count (loop count: 1 to 16,000,000, frame count per burst: 1 to 16,777,215, burst count per stream: 1 to 16,777,215) Interframe gap 64 ns to 120 s, resolution of 8 ns settable as fixed, random Interburst gap 64 ns to 120 s, resolution of 8 ns settable as fixed, random Interstream gap 64 ns to 120 s, resolution at of ns settable as fixed, random Number of streams Collision, FCS error, alignment error, dribble bit error, undersize FCS error, undersize error, oversize error, fragments error, Error insertion error, oversize error, fragments error, oversize/fcs error, IPv4 oversize/fcs error, IPv4 header checksum error, TCP/UDP header checksum error, TCP/UDP checksum error checksum error 6

7 MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module When Framed mapping is selected: Send & receive frame count/rate, send & receive byte count, send & receive data rate, capture trigger, capture filter, flow control, send & receive ARP reply count, send & receive ARP request count, send & receive PING reply count, send & receive PING request count, QoS 0-7 count/rate, user-defined 1/2 and rate, send & receive IPv4 packet count/rate, receive TCP packet count/rate, receive UDP packet count/rate, fragment, undersize, oversize, oversize & FCS error, FCS error, IPv4 header checksum error, TCP checksum error, UDP checksum error, alignment error, When Framed mapping is selected: Send & receive frame count/rate, send & receive byte count, send & receive data rate, capture trigger, capture filter, flow control, send & receive ARP reply count, send & receive ARP request count, send & receive PING reply count, send & receive PING request count, QoS 0-7 count/rate, user-defined 1/2 and rate, send & receive IPv4 packet count/rate, receive TCP packet count/rate, receive UDP packet count/rate, fragment, undersize, oversize, oversize & FCS error, FCS error, IPv4 header checksum error, TCP checksum error, UDP checksum error, byte Counters dribble bit error, collision error, line error alignment error, line error The following counters are added by the MD1230A-12 option: The following counters are added by the MD1230A-12 option: Send & receive IPv6 packet count/rate, send & receive ICMPv6 Echo Request count, send & receive ICMPv6 Echo Reply count, send & receive ICMPv6 (NA) count, send & receive ICMPv6 (NS) count The following counters are added by the MD1230A-11 option: Send & receive test frame count, sequence error, PRBS bit error count/rate, PRBS frame error count/rate When Unframed mapping is selected: Bit error count/rate, pattern sync loss count, pattern sync loss seconds Send & receive IPv6 packet count/rate, send & receive ICMPv6 Echo Request count, send & receive ICMPv6 Echo Reply count, send & receive ICMPv6 (NA) count, send & receive ICMPv6 (NS) count The following counters are added by the MD1230A-11 option: Send & receive test frame count, sequence error, PRBS bit error count/rate, PRBS frame error count/rate When Unframed mapping is selected: Bit error count/rate, pattern sync loss count, pattern sync loss seconds Latency measurement Maximum, minimum, average values Service disruption time measurement Time measurement Frame arrival time variation measurement Time resolution: 1 µs, 10 µs, 100 µs, 1 ms, 10 ms, 100 ms, 1 s With Packet BER Test (MD1230A-11 option) With Packet BER Test (MD1230A-11 option) Test pattern: Single PRBS9 Test pattern: Single PRBS9 Error insertion: PRBS error Error insertion: PRBS error With Unframed BER Test (supported on ports 1 and 5 only) With Unframed BER Test Test patterns: Test patterns: BER measurement All 0s, All 1s, Alternate1/0, All 0s, All 1s, Alternate1/0, User defined 16 bytes, PRBS23, PRBS31 User defined 16 bytes, PRBS23, PRBS31, CJPAT, CRPAT Error insertion: PRBS error Error insertion: PRBS error Error insertion timing: Error insertion timing: Single, rate (1E-3, 4, 5, 6, 7, 8, 9), Single, rate (1E-3, 4, 5, 6, 7, 8, 9), Programmable rate (9.9 E-3 to 1.0 E-10) Programmable rate (9.9 E-3 to 1.0 E-10) QoS counter setting 8-level priority frame count using either the IEEE 802.1D VLAN tag user priority field or 3 bits of the RFC2474 DSCP (DiffServ) field Capture buffer 8 Mbytes/port 32 Mbytes/port Capture filter Capture filter condition settings for each port: Destination MAC address, source MAC address, 128-bit pattern (settable bit length and offset) x 2, error conditions Capture trigger condition settings for each port: Capture trigger Destination MAC address, source MAC address, 128-bit pattern (settable bit length and offset) x 2, error conditions, traffic over, latency over, external trigger input Protocol decode Protocol emulation Ethernet, MPLS, VLAN, ARP, IPX, IPv4, ICMP for IPv4, ICMP for IPv6, IPv6, TCP, UDP, IGMP, RIP, BGP-4, DHCP, DVMRP, OSPFv2, MPLS LDP/CR-LDP, MPLS RSVP, IS-IS, IPv6 (expanded header) ARP, ICPM for IPv4, IGMP, BGP-4, OSPF (MD1230A-07 option), MPLS LDP/CR-LDP (MD1230A-08 option), MPLS RSVP (MD1230A-09 option), ICMP for IPv6 (MD1230A-12 option) 1: 1000BASE-SX/LX/LH/ZX/T can be selected by changing the GBIC module. 2: The VLAN tag and MPLS labels cannot be used simultaneously. 7

8 Ordering Information The MD1230A family includes these newly added products and options. Refer to the separate MD1230A datasheet regarding existing MD1230A family products. Model/Order No. MD1230A-07 MD1230A-08 MD1230A-09 MD1230A-10 MD1230A-11 MD1230A-12 MD1230A-13 MU120111A MU120112A Name Option OSPF Protocol MPLS (LDP/CR-LDP) Protocol MPLS (RSVP) Protocol RFC2889 Benchmarking Test Packet BER Test IPv6 Expansion XENPAK Test Plug-in modules 10/100M Ethernet Module Gigabit Ethernet Module 1 Model/Order No. MU120111A-90 MU120112A-90 G0105A G0106A G0107A G0108A G0124A 1: MU120112A requires two GBIC modules (sold separately). 2: GBIC modules are sold individually. MU120112A can accommodate two GBIC interfaces. Name Maintenance service Extended three year warranty service Extended three year warranty service Optional accessories GBIC SX 850 nm 2 GBIC LX 1310 nm 2 GBIC LH 1310 nm 2 GBIC ZX 1550 nm 2 GBIC T (1000BASE-T) 2 Specifications are subject to change without notice. ANRITSU CORPORATION , Minamiazabu, Minato-ku, Tokyo , Japan Phone: Telex: J34372 Fax: U.S.A. ANRITSU COMPANY North American Region Headquarters 1155 East Collins Blvd., Richardson, TX 75081, U.S.A. Toll Free: ANRITSU ( ) Phone: Fax: Canada ANRITSU ELECTRONICS LTD. 700 Silver Seven Road, Suite 120, Kanata, ON K2V 1C3, Canada Phone: Fax: Brasil ANRITSU ELETRÔNICA LTDA. Praia de Botafogo 440, Sala 2401 CEP , Rio de Janeiro, RJ, Brasil Phone: Fax: U.K. ANRITSU LTD. 200 Capability Green, Luton, Bedfordshire LU1 3LU, U.K. Phone: Fax: Germany ANRITSU GmbH Grafenberger Allee 54-56, Düsseldorf, Germany Phone: Fax: France ANRITSU S.A. 9, Avenue du Québec Z.A. de Courtabœuf Les Ulis Cedex, France Phone: Fax: Italy ANRITSU S.p.A. Via Elio Vittorini, 129, Roma EUR, Italy Phone: Fax: Sweden ANRITSU AB Botvid Center, Fittja Backe Stockholm, Sweden Phone: Fax: Spain ANRITSU ELECTRÓNICA, S.A. Europa Empresarial Edificio Londres, Planta 1, Oficina 6 C/ Playa de Liencres, Las Rozas. Madrid, Spain Phone: Fax: Catalog No. MU120111A/120112A-E-A-3-(1.00) Singapore ANRITSU PTE LTD. 10, Hoe Chiang Road #07-01/02, Keppel Towers, Singapore Phone: Fax: Hong Kong ANRITSU COMPANY LTD. Suite 719, 7/F., Chinachem Golden Plaza, 77 Mody Road, Tsimshatsui East, Kowloon, Hong Kong, China Phone: Fax: Korea ANRITSU CORPORATION 14F Hyun Juk Bldg , Yeoksam-dong, Kangnam-ku, Seoul, Korea Phone: Fax: Australia ANRITSU PTY LTD. Unit 3/170 Forster Road Mt. Waverley, Victoria, 3149, Australia Phone: Fax: Taiwan ANRITSU COMPANY INC. 7F, No. 316, Sec. 1, NeiHu Rd., Taipei, Taiwan Phone: Fax: Printed in Japan ddc/M