Exam questions. 1. How many HSRP (Hot Standby Routing Protocol) groups will need to be configured for each VLAN?

Transcription

1 Nguyen Khac Quyet - Take Exam Exam questions Time remaining: 00: 20: How many HSRP (Hot Standby Routing Protocol) groups will need to be configured for each VLAN? What three tasks must be performed to successfully configure Hot Standby Routing Protocol (HSRP)? Define the encapsulation type. Define the standby route. Define the IP address. Enable the standby mode. Enable HSRP 3. In what three states is it possible for an HSRP router to be in? (Select three) Standby Established Idle Active Init Backup 4. Which one of the statements below correctly describes the Virtual Router Redundancy Protocol (VRRP)? A VRRP group has one active and one or more standby virtual routers. A VRRP group has one master and one redundant virtual router. A VRRP group has one active and one or more standby virtual routers. A VRRP group has one master and one or more backup virtual routers.

2 5. On a 3550 EMI switch, which three types of interfaces can be used to configure HSRP? Loopback interface SVI interface Routed port Access port EtherChannel port BVI interface 6. The RP with the highest Priority (default is 100) is elected as the Active RP and the RP with the second highest Priority is elected as the Standby RP. If both priorities are the same, what is used as the tiebreaker for an RP to become the active RP? The RP with the lowest IP address The RP with the highest IP address The RP with the lowest MAC address The RP with the highest MAC address 7. Which of the following statements accurately describes the function of Cisco HSRP? An HSRP group consists of one or more active routers to ensure continual network link availability An HSRP group consists of exactly two standby routers to ensure continual network link availability An HSRP route processor can belong to multiple groups but only within the boundaries of a single VLAN HSRP allows multiple routers to automatically assume the function of the standby router if the current standby router fails 8. What kind of message does an HSRP configured router send out every 3 seconds? Desire Snoop Hello Send Resign 9. "Which command will need to be added to Router2 to ensure that it will take over if serial 0/0 on Router1 fails? Router1 running config.: hostname Router1 interface fastethernet 0/0 ip address standby 9 ip standby 9 priority 110 standby 9 track serial 0/0 Router2 running config.: hostname Router2 interface fastethernet 0/0 ip address standby 9 ip standby 9 track serial 0/0 standby 9 track fastethernet 0/0 standby 9 track

3 standby 9 priority 130 standby 9 preempt None of the above 10. What types of RPs will each HSRP group contain? Choose four. Virtual RP Active RP Inactive RP Standby RP Flow RP Other HSRP RPs 11. Which protocol is an extension of ICMP that allows an IP host to find a new router when a router becomes unavailable(rfc 1256)? HSRP SNMP IRDP VRRP None of the above 12. Which statement describes Virtual Router Redundancy Protocol (VRRP)? A VRRP group has one master and at least one standby virtual router. A VRRP group has one master and one more backup virtual router A VRRP group has one active and one more standby virtual routers. A VRRP group has one active and one backup virtual router. 13. HSRP supports six states in the following order: Initial, Learning, Listening, Speaking, Standby, and Active. What happens when an RP enters the Speaking state? Listens for an active RP Learns about the virtual IP address Propagates broadcast messages so it can participate in the election Propagates multicast messages so it can participate in the election 14. What three tasks must a network administrator perform to properly configure Hot Standby Routing Protocol (HSRP)? (Select three)

4 Define the encapsulation type. Define the standby router. Define the standby preempt number. Define the standby IP address. Enable the standby priority. 15. You want to allow router to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this? standby preempt standby preempt enable standby preempt hot standby preempt 16. What are the three different Op Codes contained in an HSRP multicast message? Hello message Resign message Coup message State message 17. On a 3550 EMI switch, which two types of interfaces can be used to configure HSRP? Loopback interface SVI interface Routed port Access port BVI interface 18. Which of the following describe reasons for deploying HSRP? (Select three) HSRP provides redundancy and fault tolerance HSRP allows one router to automatically assume the function of the second router if the second router starts HSRP allows one router to automatically assume the function of the second router if the second router fails HSRP provides redundancy and load balancing 19. Which of the following is a valid HSRP virtual MAC address? b07.ac11

5 0000.0a07.ac c07.ac d07.acz2 20. Which type of scheme describes the default operation of Gateway Load Balancing Protocol (GLBP)? per session using a strict priority scheme per host using a strict priority scheme per session using a round robin scheme per host using a round robin scheme per GLBP group using a round robin scheme per GLBP group using a strict priority scheme 21. In the hardware address c07.ac0av, what does 07.ac represent? HSRP well-known physical MAC address Vendor code HSRP router number HSRP group number HSRP well-known virtual MAC address 22. You are verifying HSRP and see the following output: Standby router is unknown expired What does this usually mean? A problem with the CSU/DSU Unknown router by a different vendor Maximum Age timer is set incorrectly Physical Layer problems 23. The MAC address used by the HSRP virtual router consists of three components. In the hardware address c07.ac0a, what component does 07.ac represent? Vendor code HSRP group number HSRP router number HSRP well-known physical MAC address HSRP code 24. To protect against first-hop router failure, four protocols were developed to ensure IP routing redundancy. Which of the following

6 are they? (Select four) HSRP ICMP IRDP MSTP VRRP GLBP Showing page 1 of 1 : 1 Go! 2004 HanoiCTT. All rights reserved.