Software Release Notes

Transcription

1 Software Release Notes Application System MetroStar SNMP agent MetroStar I Version Previous version Version date

2 Added features/components Serial interface (console) alarming support PCM110-8E1/T1 support PCM110-4E1/T1 support MCM1000X support GSM1000X support MSM2500U support MCM100-xT1 support LTA41-xT1 support SFP devices support CLI commands: o Test alarm send command added (diag mode only) o config system radius udpport <port#> o config system radius timeout <timeout> o config system radius retransmit <retries> o config system snmp fibrolansnmprev <rev#> 2

3 Modified features/components Improved offline config mechanism New devices added to MetroStar MIB Traps were added: o remotedeviceunifosiglost 5054 o remotedeviceunifosigdetect 5055 o SFP related traps: A/N and Pause support in MCM1000T/S, GSM1000/MA (rev 2.6 or higher) Pause support in GSM1010/MA (rev 2.6 or higher) CLI support for MSM100/622U, MCM100RL, MCM110-0x, MCM OFC support for MCM110-0x, MCM Enhanced MCM100-RL functionality Default trap community name changed to "public" Added fdx command to MCM100-01/02 Added reset command (menus too) in GSM1000/MA and GSM1010/MA Configurable RADIUS UDP port Configurable RADIUS server timeout Configurable RADIUS retransmit attempts RADIUS shared secret minimum length changed from 8 characters to 1 character Login prompt changed from Login to Username when RADIUS is enabled Allow RFU files of up to 256kbytes instead of 128kbytes Fallback mechanism to local credentials in case of any RADIUS failure SNMP traps are always sent with severity variable as the first variable. When trap severity is disabled the value of this variable is off (0) 3

4 Modified features/components MIB object sysobjectid value and (con t) enterprise value for generic traps can be changed using a system variable. This system variable can be configured via startup menu or using CLI command config system snmp fibrolansnmprev <rev#>. Revision number 1 uses the old sysobjectid (flmetrostarmibconformance), and revision 2 uses the new sysobjectid (flmschassis) SNMP traps variables are sent with their own unique OIDs instead of the OID of the trap itself Telnet session and execution timeout are both configurable with the same variable Telnet session idle timeout Telnet login is limited to a maximum of 3 retries to enter credentials NTP synchronization poll all configured servers and choose the best stratum server available NTP sync interval changed to 4-14, in seconds to the nearest power of two Warning message and confirmation request when enabling phy loopback Removed features/components None 4

5 Bugs fixed MMM-01 / Firmware Upgrade Menus: Non- Supported devices in the list MMM-01 / OFC: Setting OFC targets via telnet could cause a system crash MMM-01 / OFC: MCM with OFC yields 'unknown' offline module after copy MMM-01 / OFC: GSM1000/MA with OFC copy commands or reboot may hang system (and corrupt config) MMM-01 / OFC Help: show offline? command produces an unnecessary error message MMM-01 / RADIUS: Incorrect login reject message with invalid secret MMM-01 / RADIUS: Incorrect error message when adding/removing server through menu MMM-01 / modules: folinkdown trap is generated at CPE power up, when CPE s connected to MCM1000T/S MMM-01 / Traplog: Unsuitable timestamp for time between first and last overwrites MMM-01 / SNMP: COLDSTART traps packets are sent as malformed packets MCM Duplex mode: Wrong Duplex mode after defaults-restore MCM / "Resdef" CLI command: "Resdef" CLI does not affect channel 2 MCM100-2E1 / E1 Information: E1 "Rem. Signal" indication error MCM100-RL & MCM110-0x: No warning message when changing B/W to 0 MCM1000 Series (T/S) / Alarming: When manually setting Enable parameter to "Off" the system issues Local TP link down message MSM100U/MSM622U / SNMP: P1 loopback is not shown by SNMP get MSM100U/MSM622U / SNMP: No simultaneous Loopbacks block via SNMP MSM100/622U / SNMP: a set command on the enabled mode disables channel H.CON/MA / Duplex Mode: Duplex mode change issue GSM1000/MA / Alarming: Remote SX signal lost and Remote SX link down traps sent with wrong parameters LTA41 / CLI: No "Reset" CLI command for LTA41 devices (command added) LTA41 / SNMP: Impossible to set max. packet size parameter of LTA41 via SNMP 5

6 This page intentionally left blank 6