MP8765 Multimedia Projector

Transcription

1 MP8765 Multimedia Projector Operator's Guide MP8765 Projecteur multimedia - Guide de L' opérateur MP8765 Multimedia-Projektor - Benutzerhandbuch MP8765 Proyector de Multimedia - Guía del usuario MP8765 Proiettore Multimediale - Guida dell' operatore MP8765 Multimedia Projector - Gebruiksaanwijzing MP8765 Projector dos Multimedia - Guia da operador MP8765 Multimedia Projektør- Brukerhåndbok 3M MP8765

2 Intended Use Statement Before operating this machine, please read the Operator s Guide and Product Safety Guide thoroughly. The 3M Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages have not been tested and could damage the projector peripheral equipment and/or create a potentially unsafe operating condition. 3M Multimedia projectors are designed to operate in a normal office environment. 16 to 29 C (60 to 85 F) % RH (without condensation) m ( feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the projector. Use of this product in adverse conditions will void the product warranty.

3 Liquid Crystal Projector Operator's Guide Thank you for purchasing this liquid crystal projector. WARNING Please read the Product Safety Guide and this Operator's Guide thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. ENGLISH NOTE The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual The reproduction, transmission or use of this document or contents is not permitted without express written authority. TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned. CONTENTS Page FEATURES...2 BEFORE USE...2 Contents of Package...2 Part Names...3 Loading the Batteries...5 INSTALLATION...6 Installation of the Projector and Screen...6 Angle Adjustment...6 Cabling...7 Power Connection...8 Example of System Setup...8 Plug & Play...8 OPERATIONS...9 Power ON...9 Power OFF...9 Basic Operation...10 Setup Menu...12 Input Menu...13 Image Menu...14 Options Menu...15 No Signal Menu...16 MAINTENANCE...17 Lamp...17 Air Filter...19 Other Maintenance...19 Page TROUBLESHOOTING...20 OSD Message...20 Indicators Message...21 Symptom...22 SPECIFICATIONS...23 ACCESSORIES TABLES Table 1. Installation Reference...6 Table 2. Cabling...7 Table 3. Basic Operation...10 Table 4. Setup Menu...12 Table 5. Input Menu...13 Table 6. Image Menu...14 Table 7. Options Menu...15 Table 8. No Signal Menu...16 Table 9. OSD Message...20 Table 10. Indicators Message...21 Table 11. Symptom...22 Table 12. Specifications For "TECHNICAL", see the end of this manual. ENGLISH-1

4 Product Safety Guide MP8765 Projecteur multimedia - Guide de Securite de Produit MP8765 Multimedia-Projektor - Sicherheitsanleitung des Gerats MP8765 Proyector de Multimedia - Guía de Seguridad del Producto MP8765 Proiettore Multimediale - Guida di Sicurezza del Prodotto MP8765 Multimedia Projector - Veiligheidgids op Product MP8765 Projector dos Multimedia - Guia da Seguranca de Produto MP8765 Multimedia Projektør- Bruksabvisning for Produktsakerhets 3M MP8765 STANDBY/ON VIDEO AUTO MENU POSITION MAGNIFY LASER MENU SELECT FREEZE OFF BLANK RGB KEYSTONE RESET PinP MUTE VOLUME FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. Outstanding Brightness The UHB lamp and high-efficiency optical system assure a high level of brightness. Partial Magnification Function Interesting parts of images can be magnified for closer viewing. Distortion Correction Function Distortion-free images are quickly available. Extra-low Noise Function Acoustic noise level from the unit can be reduced. BEFORE USE Contents of Package Make sure all of the following items are included in the package. If anything is missing, please contact your dealer. NOTE Keep the original packing material for future reshipment. Power Cord (US, UK, Europe) S-Video Cable Stereo Mini-Cable Projector MP8765 Multimedia Projector VGA Cable Video/Audio Cable (with white lead) Component Video Cable (with green lead) Product Safety Guide Warranty Quick Start Guide Mouse Cable (PS/2, Serial) Batteries for Remote Control Transmitter Remote Control Transmitter ENGLISH-2

5 BEFORE USE (continued) Part Names Carrying Handle AC Inlet (to the Power Cord) Power Switch Foot Adjuster Ventilation Openings (Intake) Speaker FRONT/LEFT VIEW OF THE PROJECTOR Zoom Knob Focus Ring Remote Control Sensor Lens Foot Adjuster Lens Cap ENGLISH Control Panel (Refer to P.9 "OPERATIONS") STANDBY/ON Button KEYSTONE Button Foot Adjuster Button Filter Cover Air Filter and Intake for the Cooling Fan ( ) INPUT Button LAMP Indicator TEMP Indicator POWER Indicator RESET Button MENU Button Ventilation Openings (exhaust) REAR/RIGHT VIEW OF THE PROJECTOR Terminal Panel (Refer below) S-VIDEO Terminal COMPONENT VIDEO Y Terminal CB/PB Terminal CR/PR Terminal VIDEO IN Terminal AUDIO IN R Terminal AUDIO IN L Terminal AUDIO IN 1 Terminal AUDIO IN 2 Terminal AUDIO OUT Terminal TERMINAL PANEL Remote Control Sensor DVI Terminal RGB IN 1 Terminal RGB IN 2 Terminal CONTROL Terminal RGB OUT Terminal USB Terminal ENGLISH-3

6 BEFORE USE (continued) Part Names (continued) STANDBY/ON Button VIDEO Button Disk Pad Used to operate the mouse shift function and left click function. AUTO Button MENU Button MENU SELECT Button Used to click the left mouse button.,,, Button Used to operate the mouse shift function. POSITION Button MAGNIFY Button STANDBY/ON VIDEO LASER BLANK AUTO RGB MENU KEYSTONE MENU SELECT POSITION MAGNIFY RESET FREEZE PinP OFF MUTE VOLUME BLANK Button LASER Button RGB Button MOUSE / RIGHT Button Used to click the right mouse button. KEYSTONE Button RESET Button Used to click the right mouse button. PinP Button FREEZE Button MUTE Button VOLUME Button REMOTE CONTROL TRANSMITTER (Refer to P.9 "OPERATIONS") These functions work when the mouse control function is activated. Remember, the POSITION, BLANK ON and MENU ON functions disable the mouse control function. WARNING The laser pointer of the remote control transmitter is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. AVOID EXPOSURE- LASER RADIATIONS IS EMITTED FROM THIS APERTURE C A U T I O N LASER RADIATION- DO NOT STARE INTO BEAM MAX. OUTPUT: 1mW WAVE LENGTH: 650nm CLASS2 LASER PRODUCT LASER RADIATION DO NOT STARE INTO BEAM CLASS2 LASER PRODUCT MAX. OUTPUT: 1mW WAVE LENGTH: 650nm IEC :1993+A1:1997 Complies with 21 CFR and except for deviations pursuant to Laser Notice No.50, dated SMK CORPORATION Togoshi Shinagawa-ku, Tokyo, JAPAN MANUFACTURED Novemver 2001 PLACE OF MANUFACTURER: A NOTE Keep the remote control transmitter away from children and pets. Do not give the remote control transmitter any physical impact. Take care not to drop. Do not place the heavy objects on the remote control transmitter. Do not wet the remote control transmitter or place it on any wet object. Do not place the remote control transmitter close to the cooling fan of the projector. Do not disassemble the remote control transmitter. ENGLISH-4

7 BEFORE USE (continued) Loading the Batteries Install the AA batteries into the remote control transmitter. 1. Remove the battery cover. Push the knob while lifting up the battery cover. 2. Load the batteries. Make sure the plus and minus poles are correctly oriented. 3. Close the battery cover. 1 2 ENGLISH CAUTION Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries. This could cause battery cracking or leakage, which could result in fire or personal injury. When loading the batteries, make sure the plus and minus terminals are correctly oriented as indicated in the remote control transmitter. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment. When you dispose the battery, you should obey the law in the relative area or country. Keep the battery away from children and pets. When not to be used for an extended period, remove the batteries from the remote control transmitter. NOTE Replace the batteries when remote control transmitter operation becomes difficult. ENGLISH-5

8 INSTALLATION Installation of the Projector and Screen Refer to the drawing and table below for determining the screen size and projection distance. The projection distances shown in the table below are for full size (1024 x 768 dots). a: Distance from the projector to the screen. (±10%) Table 1. Installation Reference Screen size a [inches (m)] [inches (m)] Min. Max. 40 (1.0) 62 (1.6) 82 (2.1) 60 (1.5) 94 (2.4) 123 (3.1) 80 (2.0) 127 (3.2) 164 (4.2) 100 (2.5) 160 (4.1) 205 (5.2) 120 (3.0) 192 (4.9) 246 (6.3) 150 (3.8) 241 (6.1) 308 (7.8) 200 (5.0) 323 (8.2) 411 (10.4) Top View Side View CAUTION Install the projector in a suitable environment according to instructions of the Product Safety Guide and this manual. When you fix this unit with a metal tool and the like, you must connect it with ground wire; otherwise, fire or electric shock can result. Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using an optional three-core power-supply cord. Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and cause damage. Be especially careful not to install it with ventilation holes blocked. Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.lcd panel, Lens Assy etc.). Angle Adjustment Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0 to 9 approximately. a Press the foot Foot Adjusters adjuster button 1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle. 2. Release the button to lock at the desired angle. 3. Use the foot adjusters for fine adjustment. Do not force the adjuster screws. This could damage the adjusters or cause the lock to fail. CAUTION Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or fingers could get caught and cause personal injury. ENGLISH-6

9 INSTALLATION (continued) Cabling Refer to the table below for connecting each terminal of the projector to a device. Table 2. Cabling Function Terminal Cable RGB input RGB IN 1 VGA cable RGB IN 2 with D-sub 15-pin shrink jack RGB output RGB OUT and inch thread screws DVI input DVI DVI cable with inch thread screws Audio input (from the computer) PS/2 mouse control ADB mouse control Serial mouse control RS-232C communication AUDIO IN 1 (interlocked with RGB IN 1 or DVI) AUDIO IN 2 (interlocked with RGB IN 2) CONTROL Audio cable with stereo mini jack PS/2 mouse cable ADB mouse cable Serial mouse cable RS-232C cable USB mouse control USB USB cable S-video input S-VIDEO IN S-video cable with mini DIN 4-pin jack Video input VIDEO IN Video/Audio cable COMPONENT VIDEO Y Component video input COMPONENT VIDEO CB/PB COMPONENT VIDEO CR/PR Component video cable Audio input AUDIO IN L Video/Audio cable (from video equipment) AUDIO IN R or Audio cable with RCA jack Audio output AUDIO OUT Audio cable with stereo mini jack ENGLISH CAUTION Incorrect connecting could result in fire or electrical shock. Please read this manual and the Product Safety Guide. Before connecting, turn off to all devices to be connected, except for the USB cable. The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified. NOTE Before connecting, read instruction manuals of the devices to be connected, and make sure that the projector is compatible with the device. Secure the screws on the connectors and tighten. For some RGB input modes, the optional Mac adapter is necessary. To select the DVI input, the comuter may need some settings. See the manuals of the computer for details. Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Refer to the TECHNICAL section for the pin assignment of connectors and RS-232C communication data. When the DVI terminal is used, the RGB OUT terminal may not function. ENGLISH-7

10 INSTALLATION (continued) Power Connection Use the correct power cord depending on the power outlet to be used. Connect the AC inlet of the projector to the power outlet firmly by the power cord. CAUTION Be carful in handling the power cord according to instructions of the "Product Safety Guide" and this manual. Connect the power cord firmly. Avoid using a loose, unsound outlet or failed contact. Example of System Setup Power outlet Power Cord AC Inlet Display Monitor DVD Player COMPONENT VIDEO CR/PR CB/PB Y S-VIDEO IN AUDIO R L VIDEO IN IN 1 RGB IN 2 AUDIO IN 1 2 AUDIO OUT USB S-Video Tape Recorder RGB OUT CONTROL Computer (notebook type) Speaker with amplifier Computer (desktop type) NOTE When connecting with a notebook computer, set the proper RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information. Plug & Play This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. Please use this function by connecting the VGA cable with RGB IN 1 terminal (DDC 1/2B compatible), or by connecting a DVI cable with DVI terminal (DDC 2B compatible). Plug & play may not operate by other connections. NOTE Plug & play is a system configured with peripheral equipment including a computer, display and an operating system. This projector is recognized as a plug & play monitor. Use the standard display drivers. Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug & play does not operate correctly. ENGLISH-8

11 OPERATIONS POWER Indicator STANDBY/ON Button STANDBY/ ON Button STANDBY/ON VIDEO LASER BLANK RGB ENGLISH Zoom Knob Focus Ring AUTO MENU KEYSTONE MENU SELECT POSITION RESET FREEZE PinP MAGNIFY MUTE OFF Power Switch Lens Cap VOLUME Power ON 1. Check that the power cord is connected correctly. 2. Set the power switch to [ ]. The standby mode is selected, and the POWER indicator is turned to orange. 3. Press the STANDBY/ON button on the control panel or the remote control transmitter. Warm-up begins and the POWER indicator blinks in green. 4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens cap. 5. Adjust picture size using the zoom knob. 6. Adjust focus using the focus ring. Power OFF 1. Press the STANDBY/ON button on the control panel or the remote controller. Then,the message "Power off?" will appear on the screen, and the message will disappear by any operation or no operation for 5 seconds. During this message indication, press the STANDBY/ON button again. The projector lamp is extinguished and lamp cooling begins. The POWER indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button has no effect while the POWER indicator is blinking. 2. The system assumes the Standby mode when cooling is complete, and the POWER indicator ceases blinking and changes to orange. Check that the indicator is orange and set the power switch to [O]. 3. The POWER indicator is extinguished when power is off. Do not forget to attach the lens cap. WARNING Please read this manual, and the Product Safety Guide thoroughly before using the equipment. Always ensure that the equipment is used safely. NOTE Except in emergencies, follow the above-mentioned procedure for turning power off. Incorrect procedure will reduce the life of the projector lamp and LCD panel. To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF. Providing a RS-232C cable is connected, turn on the computer before the projector. When a projector continues projecting the same image, the image may remain as an afterimage. Please do not project the image same for a long time. ENGLISH-9

12 OPERATIONS (continued) Basic Operation The basic operations shown in Table 3 is performed from the supplied remote control transmitter or the projector control panel. Items indicated by (*) may be used from the control panel. Table 3. Basic Operation Item INPUT SELECT POSITION RESET (*) MAGNIFY FREEZE Description Select Input Signal (*) : Press the INPUT button. RGB IN 1 RGB IN 2 DVI VIDEO IN S-VIDEO IN COMPONENT VIDEO ( RGB IN 1) Select RGB Input : Press the RGB button. VIDEO IN / S-VIDEO IN / COMPONENT VIDEO RGB IN 1 / RGB IN 2 / DVI RGB IN 1 RGB IN 2 DVI ( RGB IN 1) Select Video Input : Press the VIDEO button. RGB IN 1 / RGB IN 2 / DVI VIDEO IN / S-VIDEO IN / COMPONENT VIDEO VIDEO IN S-VIDEO IN COMPONENT VIDEO ( VIDEO IN) The selected signal name is displayed for approximately 3 seconds when the input signal is changed. Set/Clear Position Adjustment Mode : Press the POSITION button. The [ ] icon is displayed in the POSITION mode. Image Position Adjustment: Press the,, and buttons in the POSITION mode. Valid only in the MAGNIFY mode with a video signal is input. After approximately 10 seconds of inactivity the [ ] icon is extinguished and the POSITION mode is cleared automatically.,, and buttons may operate as the mouse control button. Refer to page 4. Initialize Each Item : Select an item and press the RESET button. Initialize Position Adjustment : Press the RESET button and the POSITION mode. This function is valid only when RGB signal is input. Valid except for the VOLUME, LANGUAGE and H PHASE. The RESET button may operate as the mouse control button. Refer to page 4. Set MAGNIFY Mode : Press the MAGNIFY button. Move Magnified Area : Run the POSITION in the MAGNIFY mode. Adjust Magnification : Press the MAGNIFY / button in MAGNIFY mode. Clear MAGNIFY Mode : Press the MAGNIFY button. OFF The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT SELECT or VIDEO, or by changing the input signal. Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is displayed, and the image is frozen, in the FREEZE mode. The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE, Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the input signal. Do not forget to clear frozen static images. NOTE Strong light and obstacles will interfere with operation of the remote control transmitter. ENGLISH-10

13 SETUP INPUT IMAGE OPT. BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL R COLOR BAL B ASPECT CONTRAST -2 OPERATIONS (continued) Items indicated by (*) may be used from the control panel. Table 3. Basic Operation (continued) Item Description VOLUME Volume Adjustment : Press the VOLUME / button. MUTE AUTO BLANK ON/OFF MENU ON/OFF (*) MENU SELECT Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the MUTE mode. Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal position(h.posit), vertical position (V.POSIT),clock phase (H.PHASE), and horizontal size(h.size) are automatically adjusted. Use with the window at maximum size in the application display. Automatic Adjustment at Video Input : Press the AUTO button. A signal type appropriate for the input signal is selected automatically. Valid only when AUTO is set for VIDEO on the menu. This operation requires approximately 10 seconds. It may not function correctly with some input signals. Set/Clear Blank Mode: Press the BLANK button. No image is displayed in the Blank mode. The screen color is as set in BLANK on the Image menu. Menu Display Start/Stop: Press the MENU button. The menu display is terminated automatically after approximately 10 seconds of inactivity. Select Menu Type: Press the MENU SELECT button. Allows the user to select the normal menu or the single menu. Only the selected item is displayed on the single menu, and other items are displayed with the and buttons as with the normal menu. Valid only when the Setup menu is used. Push the MENU SELECT button after selecting items such as "BRIGHTNESS". The MENU SELECT button may operate as the mouse control button. Refer to page 4. Normal menu Single menu (MENU SELECT) ENGLISH P.IN P. MODE Select Mode of P.IN P. Display : Press the PinP button. Small Large P.IN P. off ( Small) P.IN P. function superimposes a video image over RGB or DVI signals. Set / Clear KEYSTONE Mode (*) : Press the KEYSTONE button. KEYSTONE Select KEYSTONE Mode : Press the / button in the KEYSTONE mode. Vertical Horizontal Adjust KEYSTONE : Press the / button. ENGLISH-11

14 OPERATIONS (continued) Setup Menu The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and video input. Select an item with the and buttons, and start operation. Use the Single menu to reduce menu size (see Table 3, MENU SELECT). Table 4. Setup Menu SETUP INPUT IMAGE OPT. BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL R COLOR BAL B ASPECT RGB IN 1 RGB IN 2 DVI SETUP INPUT IMAGE OPT. BRIGHT 0 CONTRAST +1 SHARPNESS +1 COLOR 0 TINT 0 H PHASE 0 COLOR BAL R 0 COLOR BAL B 0 ASPECT VIDEO S-VIDEO COMPONENT VIDEO Item Description RGB IN 1 RGB IN 2 DVI VIDEO S-VIDEO COMPONENT BRIGHT Adjustment: Dark Light CONTRAST Adjustment: Weak Strong V POSIT Adjustment: Down Up - - H POSIT Adjustment: Left Right - - H PHASE Adjustment: Left Right Adjust to eliminate flicker. - Adjustment: Small Large H SIZE The image may not be displayed correctly if the horizontal size is excessive. In such cases, press the RESET button, and initialize the horizontal size. - - SHARPNESS Adjustment: Soft Clear - - COLOR Adjustment: Light Dark - - TINT Adjustment: Red Green Valid only when NTSC or NTSC 4.43 signal is received. - - COLOR BAL R Adjustment: Light Dark COLOR BAL B Adjustment: Light Dark Select Image Aspect Ratio : Full [ ] 16:9[ ] Select Position of Image: Press the button while 16:9[ ] is selected. Center Down Up ( Center ) Select Image Aspect Ratio: ASPECT 4:3[ ] 16:9[ ] 4:3 small[ ] Select Position of Image : Press the button while 16:9[ ] / 4:3 small[ ] is selected. Center Down Up ( Center ) 4:3 small cannot be selected with the input of 720p or 1080i component. 4:3 small may not be displayed correctly with some input signals. ENGLISH

15 OPERATIONS (continued) Input Menu The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode. Table 5. Input Menu AUTO RGB Item VIDEO (**) HDTV SETUP INPUT IMAGE OPT. AUTO RGB VIDEO HDTV EXECUTE CANCEL Description Automatic Adjustment at RGB Input: Select the EXECUTE with the button. Horizontal position (H.POSIT), vertical position (V.POSIT), clock phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted. Use with the window at maximum size in the application display. Automatic Adjustment at Video Input: Select the EXECUTE with the button. A signal type appropriate for the input signal is selected automatically when EXECUTE is selected automatically. Valid only when AUTO is set for VIDEO on the menu. This operation requires approximately 10 seconds. It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem. This function is the same as for the AUTO function in Basic operation. Displays RGB Input Frequency: Displays the horizontal and vertical sync signal frequencies for RGB input. Valid only at RGB input. Select Video Signal Type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as appropriate for the input signal. The selection of AUTO enables and executes the function AUTO (Automatic Adjustment at Video Input), except for the N-PAL input. Use this function when the image becomes unstable (eg. the image becomes irregular, or lacks color) at VIDEO/S-VIDEO input. Automatic Adjustment requires approximately 10 seconds. It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem except for the N-PAL input. For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the signal of HDTV. Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input signal with the / button. ENGLISH ENGLISH-13

16 OPERATIONS (continued) Image Menu The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. Table 6. Image Menu Item BLANK START UP MyScreen ENGLISH-14 Description SETUP INPUT IMAGE OPT. BLANK START UP MyScreen MIRROR P. IN P. POSIT P. IN P. INPUT GAMMA MyScreen ORIGINAL Select Blank Screen: Select the screen in case of the BLANK mode with the / button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the BLANK mode is ON. MyScreen is a mode that the customer-customized screen is displayed. This is the blue screen at the factory setting. Refer to the description of MyScreen below. ORIGINAL is a mode that the factory fixed screen is displayed. When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes. Select Start Up Screen: Select the screen in case of no signal input with the / button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when no signal is input. My Screen is a mode that the customer-customized screen is displayed. This is the blue screen at the factory setting. Refer to the description of MyScreen below. ORIGINAL is a mode that the factory fixed screen is displayed. TURN OFF displays the blue screen. When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes. Set MyScreen Mode: Select the EXECUTE with the button to display the MyScreen menu and set the MyScreen mode for BLANK and START UP functions. ESC clears and closes the menu box. NORM. is default of the MyScreen menu. FREEZE freezes the image and displays the frame to capture. Press the button after freeze to go to the MyScreen Capture Position mode. In the MyScreen Capture Position mode, the buttons,, and allow to move the frame to capture. After adjusting the position, press the KEYSTONE button to go to the MyScreen Display Size mode. To cancel freezing and return to the NORM. of the MyScreen menu, press the RESET button. In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with the button /. After selecting the magnification, press the KEYSTONE button to go to the CAPT. mode and start capturing. To return to the MyScreen Capture Position mode, press the RESET button. CAPT. executes a capturing the image. It requires about 20 seconds. After capturing, the captured image will be displayed for about 10 seconds. MIRROR Select Mirror Status: Select mirror status with / button. P. IN P. POSIT P. IN P. INPUT GAMMA Select Position of P. in P. Display : Press the or button. P.IN P. function superimposes a video image over RGB or DVI signals. Select signal of P. in P. Display : Press the or button. VIDEO S-VIDEO Select Gamma Mode: Select the gamma mode with the / button. NORMAL CINEMA DYNAMIC

17 OPERATIONS (continued) Options Menu The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. Table 7. Options Menu Item VOLUME Reduce Increase Description SETUP INPUT IMAGE OPT. VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE MENU COLOR Select Menu Background Color: Select with the / button. LANGUAGE Select Menu Display Language: Select with the / button. AUTO OFF SYNC ON G WHISPER Set AUTO OFF: Set 1~99 minutes with the / button. The system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select STOP (0 min.) with the button. When STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Valid: Select TURN ON with the button. SYNC ON G Invalid: Select TURN OFF with the button. May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set SYNC ON G to invalid, and reconnect the signal. Set / Crear WHISPER Mode: Press the / button. When the WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise level from the unit is reduced, and brightness level on screen is a little lower. Select Remote Control Sensor: Select the sensors to activate along the menu with the / button. Use this function if the remote does not work stably. The ambient light may affect the remote. 16 ENGLISH IR REMOTE SETUP INPUT IMAGE OPT. VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE : active : inactive ENGLISH-15

18 OPERATIONS (continued) No Signal Menu The same adjustments and settings are available with the Image and Options menus when the MENU button is pressed during display of the NO INPUT IS DETECTED ON *** or SYNC IS OUT OF RANGE ON *** message while no signal is received.select an item with the and buttons, and start or stop operation with the and buttons. Table 8. No Signal Menu Item VOLUME BLANK START UP Description VOLUME BLANK START UP MIRROR MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE Reduce Increase When this function is used, audio input is automatically switched to video. The audio input can be switched by moving the DISK PAD left and right during the display of the volume adjustment bar. The volume adjustment bar is displayed by pressing VOLUME / button. Select Blank Screen: Select the screen in case of the BLANK mode with the / button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the BLANK mode is ON. MyScreen is a mode that the customer-customized screen is displayed. This is the blue screen at the factory setting. Refer to the description of MyScreen below. ORIGINAL is a mode that the factory fixed screen is displayed. When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes. Select Start Up Screen: Select the screen in case of no signal input with the / button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when no signal is input. My Screen is a mode that the customer-customized screen is displayed. This is the blue screen at the factory setting. Refer to the description of MyScreen below. ORIGINAL is a mode that the factory fixed screen is displayed. TURN OFF displays the blue screen. When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes. MIRROR Select Mirror Status: Select the mirror status with the / button. MENU COLOR Select Menu Background Color: Select the color with the / button. LANGUAGE Select Menu Display Language: Select the language with the / button. AUTO OFF SYNC ON G WHISPER Set AUTO OFF: Set 1~99 minutes with the / button. The system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select the STOP (0 min.) with the button. When the STOP is selected the system does not enter the standby mode even if no signal is received. SYNC ON G Valid: Select the TURN ON with the button. SYNC ON G Invalid: Select the TURN OFF with the button. May not be displayed correctly with some input signals when the SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid, and reconnect the signal. Set / Crear WHISPER Mode: Press the / button. When the WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level from the unit is reduced, and brightness level on screen is a little lower. Select Remote Control Sensor: Select the sensors to activate along the menu with the / button. Use this function if the remote does not work stably. The ambient light may affect the remote. 16 IR REMOTE VOLUME BLANK START UP MIRROR MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE : active : inactive ENGLISH-16

19 MAINTENANCE Lamp HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Contact your dealer before replacing the lamp. For the optional lamp, see the item ACCESSORIES of P.24. Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high temperatures. ENGLISH WARNING For disposal of used lamp, treat according to the instruction of community authorities. Since the lamp is made of glass, do not apply shock to it and do not scratch it. Also, do not use old lamp. This could also cause explosion of the lamp. Premature lamp failure MAY be caused by an electronic component in the projector and not necessarily the lamp. If unsure contact your local service center. If it is probable that the lamp has exploded (explosive sound is heard), disconnect the power plug from the power outlet and ask your dealer to replace lamp. The lamp is covered by front glass, but in rare cases, the reflector and the inside of the projector may be damaged by scattered broken pieces of glass, and broken pieces could cause injury when being handled. Do not use the projector with the lamp cover removed. Reflector Lamp Front glass Lamp Life Projector lamps have a finite life. The image will become darker, and hues will become weaker, after a lamp has been used for a long period of time. Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21. NOTE The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. ENGLISH-17

20 MAINTENANCE (continued) Replacing the Lamp 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp. 3. Check that the projector has cooled sufficiently, and gently turn it upside down. 4. Loosen the two screws as shown in the diagram, and remove the lamp cover. 5. Loosen the three screws, and gently remove the lamp while holding the grips. Touching the inside of the lamp case may result in uneven coloring. 6. Install the new lamp and tighten the three screws firmly. Also steadily push the opposite side of the screwed lamp into the unit. 7. Replace the lamp cover in position and tighten the two screws firmly. 8. Gently turn the projector right-side up. CAUTION Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. Do not use the projector with the lamp cover removed. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP indicator is red, or the CHANGE THE LAMP message is displayed, complete the following operation within ten minutes of switching power ON. The power will be turned off automatically in over 10 minutes. 1. Switch power ON, and press the RESET button, for approximately three seconds. The LAMP xxxx hr message will appear on the lamp timer on the bottom of the screen. 2. Press the MENU button on the remote control transmitter, or the RESET button on the control panel, while the lamp timer is displayed. The LAMP xxxx 0 CANCEL message will then appear. 3. Press the and select 0, and wait until the timer display is cleared. NOTE Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly. ENGLISH-18

21 MAINTENANCE (continued) Air Filter Cleaning the air Filter The air filter should be cleaned as described below at intervals of approximately 100 hours. 1. Switch the projector power supply OFF, and remove the power cord from the power outlet. 2. Clean the air filter with a vacuum cleaner. Replacing the Air Filter Replace the air filter if contamination cannot be removed, or if it is damaged. 1. Remove the filter cover. 2. Remove the old filter. 3. Set the new filter and the filter cover. ENGLISH CAUTION Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the Product Safety Guide thoroughly to ensure that maintenance is performed correctly. Replace the air filter if contamination cannot be removed, or if it is damaged. Contact your dealer in such case. For the optional air filter, see the item ACCESSORIES of P.24. Do not use the equipment with the air filter removed. When the air filter is clogged with dust etc. the power supply is switched OFF automatically to prevent the temperature rising inside the projector. Other Maintenance Maintenance Inside the Equipment For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two years. Maintaining the equipment by yourself is dangerous. Cleaning the Lens Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands. Cleaning the Cabinet and Remote control transmitter Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth. CAUTION Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the Product Safety Guide thoroughly to ensure that maintenance is performed correctly. Do not use detergents or chemicals other than those noted above (e.g. benzene or thinners). Do not use cleaning sprays. Do not rub with hard materials, or tap the equipment. ENGLISH-19

22 TROUBLESHOOTING Service Infomation For product infomation,product assistance,service infomation,or to order accessories,please call: In U.S.or Canada : In other locations,contact your local 3M sales office. OSD Message The messages as described below may appear on the screen at power ON. Take the appropriate measures when such messages appears. Table 9. OSD Message Message Contents CHANGE THE LAMP The usage time of lamp will be reaching 2000 hr AFTER REPLACING LAMP, shortly.(*2) RESET THE LAMP TIME. It is recommended to replace the lamp soon. Prepare a (*1) new lamp as a replacement. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. THE POWER WILL TURN OFF AFTER ** hr. (*1) CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. THE POWER WILL TURN OFF AFTER 0 hr. The usage time of lamp will be reaching 2000 hr shortly. It is recommended to replace the lamp within * * hours.(*2) It might be happened that the lamp is cut off before * * hr by any chance. Power will be switched OFF automatically in * * hours. Replace the lamp as shown in P.17~18 Lamp. Always reset the lamp timer after replacing the lamp. The usage time of lamp is about to reach. Power will be switched OFF in a few minutes.(*2) Switch power OFF immediately and replace the lamp as shown in P.17 ~18 Lamp. Always reset the lamp timer after replacing the lamp. NO INPUT IS DETECTED ON *** SYNC IS OUT OF RANGE ON *** No input signal found. Check signal input connections and signal sources. The horizontal or vertical frequency of the input signal is not within the specified range. Check the specifications of the equipment and the signal source. NOTE (*1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON. (*2) The unit has a function to turn the power off which will be active when the usage time reaches 2000 hr. However the life of lamp might be much different among lamps, so that it might be happened that a lamp is cut off before the function is active. ENGLISH-20

23 TROUBLESHOOTING (continued) Indicators Message The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures. Table 10. Indicators Message POWER indicator Lights orange Blinks green Lights green Blinks orange LAMP indicator TEMP indicator Turns off Turns off The Standby mode has been set. Turns off Turns off Warming up. Please wait. Turns off Turns off ON. Normal operation possible. Turns off Turns off Cooling. Please wait. Blinks red - - Blinks /Lights red Blinks /Lights red Lights red Blinks red Turns off Turns off Blinks /Lights red Turns off Blinks red Blinks /Lights red Lights green Turns off Lights red Blinks red Blinks red Contents Cooling. Please wait. The error is found. Take the appropriate measures when the POWER indicator ceases blinking Lamp is not lit. The interior of the equipment may be too hot. Switch power OFF, wait 20 minutes until the equipment cools, and check whether the ventilation openings are blocked, whether the air filter is dirty, or whether the ambient temperature exceeds 35 C. And switch power ON again. Replace the lamp if the same problem occurs. Lamp or lamp cover is not found, or hasn t been fitted in correctly. Switch power OFF, and wait for 45 minutes until the equipment cools. Check fitting of the lamp and lamp cover, and switch power ON again. Contact your dealer if the same problem occurs again. The cooling fan is not operating. Switch power OFF, and wait for 20 minutes until the equipment cools. Check for foreign matters in the fan, and switch power ON again. Contact your dealer if the same problem occurs again. The interior of the equipment is too hot. Switch power OFF, and wait for 20 minutes until the equipment cools. Check whether the ventilation openings are blocked, whether the air filter is dirty, or whether the ambient temperature exceeds 35 C. Then switch power ON again. Contact your dealer if the same problem occurs again. The interior of the equipment is too cool. Check whether the ambient temperature is below 0 C. Contact your dealer if the same problem occurs when the ambient temperature is 0~35 C. NOTE When the internal temperature becomes excessive power is switched OFF automatically for safety reasons, and the indicator is extinguished. Set the power switch to [O] and wait for 20 minutes until the equipment has cooled sufficiently. ENGLISH ENGLISH-21

24 TROUBLESHOOTING (continued) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Table 11. Symptom Symptom Possible cause Remedy Page The power is not turned on. No video or audio. The main power switch is not turned on. The power cord is disconnected. The input is not correctly set. Turn on the main power switch. Plug the power cord into an AC power outlet. Use the projector or remote control transmitter to set. No signal input. Connect correctly. 7,8 8,9 10 Video is present but no audio. The projector is not correctly connected. The volume is set to minimum. Connect correctly. 7,8 Press VOLUME on the remote control or display the menu screen and adjust the volume. 11,15 Mute is turned on. Press the MUTE button. 11 Audio is present but no video. The projector is not correctly connected. The brightness adjustment knob is rotated fully clockwise. Connect correctly. 7,8 Select BRIGHT with the MENU button and the press the button. 12 The lens cap is still attached. Remove the lens cap. 9 Colors are pale and color matching is poor. Images are dark. Color density and color matching are not correctly adjusted. Brightness and contrast are not correctly adjusted. The lamp is nearing the end of its service life. Adjust the video. 12 Adjust the video. 12 Replace with a new lamp. 17 WHISPER mode is set. Clear WHISPER mode. 15 Video is blurred. Focus or H PHASE is out of adjustment. Adjust the focus or H PHASE. 9,12 ENGLISH-22

25 SPECIFICATIONS Table 12. Specifications Item Specification Product name Liquid crystal projector Liquid Panel size 2.3 cm (0.9 type) crystal Drive system TFT active matrix panel Pixels 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm Lamp 250 W UHB Speaker 1.0W+1.0W (stereo) Power supply AC100 ~ 120V, 4.5A / AC220 ~ 240V, 1.9A Power consumption 410W Temperature range 0 ~ 35 C (Operating) Size 360 (W) x 106 (H) x (D) mm Weight (mass) 4.5 kg RGB signal input Video signal input Signal output Control functions RGB IN DVI AUDIO IN VIDEO IN S-VIDEO IN COMPONENT VIDEO AUDIO IN RGB OUT AUDIO OUT CONTROL USB 1 Video: Analog 0.7Vp-p, 75Ω terminator (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level 2 D-sub 15-pin shrink jack TMDS, DC: 150~1200 mv / AC: 1.56 Vp-p TTL Level (Positive/Negative) RGB1 DVI RGB2 Y CB/CR PB/PR L R 200mVrms, 50 kω (max. 3.0Vp-p) Stereo mini jack 1.0Vp-p, 75Ω terminator RCA jack Brightness signal: 1.0Vp-p, 75Ω terminator Color signal: 0.286Vp-p (NTSC, burst signal),75ω terminator 0.300Vp-p (PAL/SECAM, burst signal),75ω terminator Mini DIN 4-pin jack 1.0 Vp-p, 75 Ω Terminator (Positive) 0.7 Vp-p, 75 Ω Terminator (Positive) 0.7 Vp-p, 75 Ω Terminator (Positive) 200mVrms, 50 kω (max. 3.0Vp-p) RCA jack Video: Analog 0.7Vp-p, 75Ω output impedance (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack 200mVrms, output impedance 1 kω (max. 3.0Vp-p) Stereo mini jack D-sub 15-pin shrink plug USB jack (B type) ENGLISH NOTE This specifications are subject to change without notice. ENGLISH-23

26 ACCESSORIES Acccessories...Part Number UHB Lamp, 250W Air Filter Power Cord (US) Power Cord (UK) Power Cord (Europe) VGA Cable RCA Component Cable RCA Video/Audio Cable S-Video Cable Stereo Mini-Cable Mouse Cable (PS/2) Mouse Cable (Serial) Remote Control Transmitter Not Included with Basic Packet...Part Number Ceiling mount Adjustable Height Suspension Shipping Case Carry Case Mouse Cable (ADB) Mouse Cable (USB) RS-232C Control Cable Mac Adapter How to Order Please order these parts through your dealer, or contact 3M Customer Service at the following number : In U.S. or Canada : In other locations,contact your local 3M sales office. ENGLISH-24

27 TECHNICAL Dimension Diagram 360 Pin No Signal Pin No Signal Pin No Signal 1 Video input Red 9 - RGB IN 1: SCL(DDC) 2 Video input Green 10 Ground 15 RGB IN 2: - 3 Video input Blue 11 - RGB OUT: RGB IN 1: SDA(DDC) 5 Ground 12 RGB IN 2: - 6 Ground Red RGB OUT: - 7 Ground Green 13 H. sync./ Composite sync. 8 Ground Blue 14 Vertical sync Mini Din 4-pin Connector (S-VIDEO) Pin No Signal Color:0.286Vp-p (NTSC, burst signal),75ω terminator Vp-p (PAL/SECAM, burst signal),75ω terminator 2 Brightness:1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Unit : mm Signal Connector Pin Assignment 1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT) 2. Digital Receptacle Connector (DVI) Pin No Signal Pin No Signal Pin No Signal 1 T.M.D.S. Data 2-11 T.M.D.S. Data 1 / 3 Shield 21-2 T.M.D.S. Data T.M.D.S. Clock Shield 3 T.M.D.S. Data 2 / 4 Shield T.M.D.S. Clock V Power 24 T.M.D.S. Clock Ground (+5V, Analog H/V Sync.) 6 DDC Clock 16 Hot-Plug Sense 7 DDC Data 17 T.M.D.S. Data Analog V. Sync. 18 T.M.D.S. Data T.M.D.S. Data 1-19 T.M.D.S. Data 0 / 5 Shield 10 T.M.D.S. Data TECHNICAL - 1 TECHNICAL

28 TECHNICAL (continued) Example of computer signal Resolution H V fh (khz) fv (Hz) Rating Signal mode Display mode VESA VGA-1 Zoom in VESA VGA-2 Zoom in VESA TEXT Zoom in VESA VGA (60Hz) Zoom in Mac13"mode Zoom in VESA VGA (72Hz) Zoom in VESA VGA (75Hz) Zoom in VESA VGA (85Hz) Zoom in VESA SVGA (56Hz) Zoom in VESA SVGA (60Hz) Zoom in VESA SVGA (72Hz) Zoom in VESA SVGA (75Hz) Zoom in VESA SVGA (85Hz) Zoom in Mac16"mode VESA XGA (60Hz) VESA XGA (70Hz) VESA XGA (75Hz) VESA XGA (85Hz) VESA SXGA (75Hz) Zoom out VESA SXGA (60Hz) Zoom out VESA SXGA (60Hz) Zoom out VESA SXGA (75Hz) Zoom out NOTE Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. The image may not be displayed correctly when the input sync. signal is "Composite Sync." or "Sync. on G". The image might be something wrong with computer by computer on the DVI mode. In this case, it is recommended to reduce the resolution and / or reflesh rate. TECHNICAL - 2