COMMANDS MANUAL TG2460H TG2480H TL60 TL80

Transcription

1 COMMANDS MANUAL TG2480H TL80

2 CUSTOM S.p.A. Via Berettine 2/B Fontevivo (PARMA) - Italy Tel. : Fax : http: Customer Service Department: support@custom.it 2014 CUSTOM S.p.A. Italy. All rights reserved. Total or partial reproduction of this manual in whatever form, whether by printed or electronic means, is forbidden. While guaranteeing that the information contained in it has been carefully checked, CUSTOM S.p.A. and other entities utilized in the realization of this manual bear no responsibility for how the manual is used. Information regarding any errors found in it or suggestions on how it could be improved are appreciated. Since products are subject to continuous check and improvement, CUSTOM S.p.A. reserves the right to make changes in information contained in this manual without prior notii cation. The pre-installed multimedia contents are protected from Copyright CUSTOM S.p.A. Other company and product names mentioned herein may be trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. CUSTOM S.p.A. assumes no responsibility with regard to the performance or use of these products. THE IMAGES USED IN THIS MAN- UAL ARE USED AS AN ILLUSTRA- TIVE EXAMPLES. THEY COULDN T REPRODUCE THE DESCRIBED MODEL FAITHFULLY. UNLESS OTHERWISE SPECIFIED, THE INFORMATION GIVEN IN THIS MANUAL ARE REFERRED TO ALL MODELS IN PRODUCTION AT THE ISSUE DATE OF THIS DOCUMENT. GENERAL SAFETy INFORMATION your attention is drawn to the following actions that could compromise the characteristics of the product: Read and retain the instructions which follow. Follow all indications and instructions given on the device. Make sure that the surface on which the device rests is stable. If it is not, the device could fall, seriously damaging it. Make sure that the device rests on a hard (non-padded) surface and that there is sufi cient ventilation. When positioning the device, make sure cables do not get damaged. Use the type of electrical power supply indicated on the device label. If uncertain, contact your dealer. Make sure the electrical system that supplies power to the device is equipped with a ground wire and is protected by a differential switch. Do not block the ventilation openings. Do not insert objects inside the device as this could cause short-circuiting or damage components that could jeopardize printer functioning. Do not carry out repairs on the device yourself, except for the normal maintenance operations given in the user manual. Make sure that there is an easily-accessible outlet with a capacity of no less than 10A closely to where the device is to be installed. Periodically perform scheduled maintenance on the device to avoid dirt build-up that could compromise the correct, safe operation of the unit. Before any type of work is done on the machine, disconnect the power supply. Do not touch the head heating line with bare hands or metal objects. Do not perform any operation inside the printer immediately after printing because the head and motor tend to become very hot. GENERAL INSTRUCTIONS CUSTOM S.p.A. declines all responsibility for accidents or damage to persons or property occurring as a result of tampering, structural or functional modii cations, unsuitable or incorrect installations, environments not in keeping with the equipment s protection degree or with the required temperature and humidity conditions, failure to carry out maintenance and periodical inspections and poor repair work. THE CE MARK AFFIXED TO THE PRODUCT CERTIFy THAT THE PRODUCT SAT- ISFIES THE BASIC SAFETy REQUIREMENTS. The device is in conformity with the essential Electromagnetic Compatibility and Electric Safety requirements laid down in Directives 2006/95/CE and 2004/108/CE inasmuch as it was designed in conformity with the provisions laid down in the following Standards: EN Class B (Limits and methods of measurements of radio disturbance characteristics of Information Technology Equipment) EN (Information Technology Equipment Immunity characteristics Limits and methods of measurement) EN (Safety of information equipment including electrical business equipment) GUIDELINES FOR THE DISPOSAL OF THE PRODUCT The crossed-out rubbish bin logo means that used electrical and electronic products shall NOT be mixed with unsorted municipal waste. For more detailed information about recycling of this product, refer to the instructions of your country for the disposal of these products. Do not dispose of this equipment as miscellaneous solid municipal waste, but arrange to have it collected separately. The re-use or correct recycling of the electronic and electrical equipment (EEE) is important in order to protect the environment and the wellbeing of humans. In accordance with European Directive WEEE 2002/96/EC, special collection points are available to which to deliver waste electrical and electronic equipment and the equipment can also be handed over to a distributor at the moment of purchasing a new equivalent type. The public administration and producers of electrical and electronic equipment are involved in facilitating the processes of the re-use and recovery of waste electrical and electronic equipment through the organisation of collection activities and the use of appropriate planning arrangements. Unauthorised disposal of waste electrical and electronic equipment is punishable by law with the appropriate penalties. The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this copy.

3 INTRODUCTION TG2460 EMULATION ESC/POS EMULATION ALIGNMENT

4

5 INTRODUCTION Each command reported in this manual is described as shown in the following picture. In the irst heading ield is reported the hexadecimal command value and the ASCII command value. In the second heading ield reported the command function. In the third heading ield are listed the devices on which it is possible to use the command (for example, device AAAA). 0x0D Print and carriage return <CR> Command value Command function AAAA BBBB CCCC Devices that use the command [Format] ASCII CR Hex 0D Decimal 13 [Range] When autofeed is CR enabled, this command functions in the same way as 0x0A, otherwise it is disregarded. This command sets the print position to the beginning of the line. Information valid for devices AAAA, BBBB, CCC AAAA BBBB Information valid for devices AAAA, BBBB This command sets the print position to the beginning of the line. CCCC This command is immediately executed even when Information the data valid buffer for device is full. CCCC This status is transmitted whenever data sequence is received. [Default] 0x0A Information valid only for the devices marked in bold Information valid for all the devices listed in the third heading field Introduction 5

6 The ields shown in the scheme of the previous igure have the following meaning: [Format] ASCII, hexadecimal and decimal command value. [Range] Limits of the values the command and its variables can take Description of command function Additional information about command use and settings. [Default] Default value of the command and its variables. Pertaining commands related to described command. Example of using the command Listed below are the meanings of some of symbols that may be found in the command description: 0x indicates the representation of the command hexadecimal value (for example 0x40 means HEX 40). n, m, t, x, y are optional parameters that can have different values. 6 Introduction

7 PAPER SPECIFICATIONS NOTE: All the dimensions shown in the following igures are in millimetres. TG2480H 20 10, ,5 15 NON-THERMAL SIDE 5 21 NON-THERMAL SIDE min 106 PAPER WIDTH = 60 PAPER WIDTH = 80 Introduction 7

8 TL80 6,5 16,5 min NON-THERMAL SIDE NON-THERMAL SIDE min 55 PAPER WIDTH = 60 PAPER WIDTH = 80 8 Introduction

9 TG2460 EMULATION

10 COMMANDS LISTED IN ALPHANUMERIC ORDER 0x08...<BS> x09...<HT> x0A <LF> x0D...<CR> x10 0x04...<DLE EOT> x18...<CAN> x1B 0x20...<ESC SP> x1B 0x21...<ESC!> x1B 0x2A...<ESC *> x1B 0x2D...<ESC -> x1B 0x30...<ESC 0> x1B 0x32...<ESC 2> x1B 0x33...<ESC 3> x1B 0x34...<ESC 4> x1B 0x3D...<ESC => x1B 0x1B 0x44...<ESC D> x1B 0x45...<ESC E> x1B 0x47...<ESC G> x1B 0x4A...<ESC J> x1B 0x52...<ESC R> x1B 0x56...<ESC V> x1B 0x5C...<ESC \> x1B 0x61...<ESC a> x1B 0x63 0x35...<ESC c 5> x1B 0x64...<ESC d> TG2460 emulation

11 0x1B 0x69...<ESC i> x1B 0x74...<ESC t> x1B 0x76...<ESC v> x1B 0x78...<ESC x> x1B 0x7B...<ESC {> x1B 0xFA x1B 0xFF x1C 0xC0 0x x1C 0xC x1D 0x21...<GS!> x1D 0x3A...<GS :> x1D 0x42...<GS B> x1D 0x43 0x <GS C 0> x1D 0x43 0x <GS C 1> x1D 0x43 0x <GS C 2> x1D 0x43 0x3B...<GS C ;> x1D 0x48...<GS H> x1D 0x49...<GS I> x1D 0x4C...<GS L> x1D 0x50...<GS P> x1D 0x57...<GS W> x1D 0x5E...<GS ^> x1D 0x63...<GS c> x1D 0x66...<GS f> x1D 0x68...<GS h> x1D 0x6B...<GS k>...22 TG2460 emulation 11

12 0x1D 0x72...<GS r> x1D 0x77...<GS w> x1D 0x7C...<GS > x1D 0x7E...<GS ~> x1D 0xDC TG2460 emulation

13 COMMANDS LISTED By FUNCTION BARCODE COMMANDS 0x1D 0x48...<GS H>...19 Select printing position of Human Readable Interpretation (HRI) 0x1D 0x66...<GS f>...20 Select font for HRI characters 0x1D 0x68...<GS h>...21 Set bar code height 0x1D 0x6B...<GS k>...22 Print bar code 0x1D 0x77...<GS w>...25 Set bar code width CHARACTERS COMMANDS 0x1B 0x20...<ESC SP>...27 Set character right-side spacing 0x1B 0x21...<ESC!>...28 Set print mode 0x1B 0x2D...<ESC ->...30 Turn underline mode on/off 0x1B 0x34...<ESC 4>...31 Set / reset script mode 0x1B 0x45...<ESC E>...32 Select bold mode 0x1B 0x47...<ESC G>...33 Select double-strike mode 0x1B 0x52...<ESC R>...34 Select international character set 0x1B 0x56...<ESC V>...35 Set print mode rotated by 90 0x1B 0x74...<ESC t>...36 Select character code table 0x1B 0x7B...<ESC {>...37 Select upside-down printing mode TG2460 emulation 13

14 0x1D 0x21...<GS!>...38 Select character size 0x1D 0x42...<GS B>...39 Turn white / black reverse printing on/off 0x1D 0x7E...<GS ~>...40 Set superscript / subscript PRINTING COMMANDS 0x0A <LF>...41 Print and line feed 0x0D...<CR>...42 Print and line feed 0x1B 0x4A...<ESC J>...43 Print and feed paper 0x1B 0x64...<ESC d>...44 Print and feed paper n lines 0x1B 0x78...<ESC x>...45 Select speed / quality mode 0x1D 0x7C...<GS >...46 Set printing density STATUS COMMANDS 0x10 0x04...<DLE EOT>...47 Transmission of status in real time 0x1B 0x76...<ESC v>...53 Transmit paper status 0x1D 0x72...<GS r>...54 Transmit status LINE SPACING COMMANDS 0x1B 0x30...<ESC 0>...55 Select 1/8-inch line spacing 14 TG2460 emulation

15 0x1B 0x32...<ESC 2>...56 Select 1/6-inch line spacing 0x1B 0x33...<ESC 3>...57 Set line spacing using minimum units PRINTING POSITION COMMANDS 0x08...<BS>...59 Moving back of one character 0x09...<HT>...60 Horizontal tabs 0x18...<CAN>...61 Cancel print data buffer 0x1B 0x44...<ESC D>...62 Set horizontal tab position 0x1B 0x5C...<ESC \>...63 Set relative print position 0x1B 0x61...<ESC a>...64 Select justiication 0x1D 0x4C...<GS L>...65 Set left margin 0x1D 0x57...<GS W>...66 Set printing area width BIT-IMAGE COMMANDS 0x1B 0x2A...<ESC *> Set bit image mode 0x1B 0xFA Print graphic bank (448 * 584 dots) MACRO FUNCTION COMMANDS 0x1D 0x3A...<GS :>...71 Start / end macro of deinition TG2460 emulation 15

16 0x1D 0x5E...<GS ^>...72 Execute macro MECHANISM CONTROL COMMANDS 0x1B 0x69...<ESC i>...73 Total cut 0x1C 0xC0 0x Total cut and automatic paper moving back ANTI-JAMMING COMMANDS 0x1C 0xC Enable/disable automatic anti-jamming movement 0x1D 0xDC Perform the anti-jamming movement MISCELLANEOUS COMMANDS 0x1B 0x3D...<ESC =>...77 Select device 0x1B Inizialize the printer 0x1B 0x63 0x35...<ESC c 5>...79 Enable / disable panel keys 0x1B 0xFF Receive and store logos in lash 0x1D 0x43 0x <GS C 0> Select counter print mode 0x1D 0x43 0x <GS C 1> Select count mode (A) 0x1D 0x43 0x <GS C 2> Select counter 0x1D 0x43 0x3B...<GS C ;>...85 Select count mode (B) 16 TG2460 emulation

17 0x1D 0x49...<GS I>...86 Transmit printer ID 0x1D 0x50...<GS P>...88 Set horizontal and vertical motion units 0x1D 0x63...<GS c>...89 Print counter TG2460 emulation 17

18 18 TG2460 emulation

19 BARCODE COMMANDS 0x1D 0x48 <GS H> Select printing position of Human Readable Interpretation (HRI) [Format] ASCII GS H n Hex 1D 48 n Decimal n [Range] 0 n 3 48 n 51 Selects the printing position of HRI characters when printing bar code. n selects the printing position as follows: n FUNCTION 0, 48 Not printed 1, 49 Above the bar code. 2, 50 Below the bar code. 3, 51 Both above and below the bar code HRI characters are printed using the font speciied by 0x1D 0x66. [Default] n = 0 0x1D 0x66, 0x1D 0x6B TG2460 emulation 19

20 0x1D 0x66 <GS f> Select font for HRI characters [Format] ASCII GS f n Hex 1D 66 n Decimal n [Range] n = 0, 1, 48, 49 Selects a font for the HRI characters used when printing a bar code. n selects a font from the following table: n FONT 0, 48 Font A 1, 49 Font B The HRI characters are printed at the position speciied by the command 0x1D 0x48. [Default] n = 0 0x1D 0x48, 0x1D 0x6B 20 TG2460 emulation

21 0x1D 0x68 <GS h> Set bar code height [Format] ASCII GS h n Hex 1D 68 n Decimal n [Range] 1 n 255 Sets the height of the bar code. n speciies the number of dots in the vertical direction. [Default] n = 96 (12 mm) 0x1D 0x6B TG2460 emulation 21

22 0x1D 0x6B <GS k> Print bar code [Format 1] ASCII GS k m <data> NUL Hex 1D 6B m <data> 00 Decimal m <data> 0 [Format 2] ASCII GS k m n <data> Hex 1D 6B m n <data> Decimal m n <data> [Range] Formato 1 0 m 6 Formato 2 65 m 73 Selects a bar code system and prints the bar code. m selects a bar code system as follows: Formato 1 m BARCODE SySTEM No. OF CHARACTERS REMARKS 0 UPC-A 11 k d 57 1 UPC-E 11 k d 57 2 EAN13 (JAN) 12 k d 57 3 EAN8 (JAN) 7 k 8 48 d 57 4 CODE39 1 k 48 d 57, 65 d 90, 32, 36, 37, 43, 45, 46, 47 5 ITF 1 k (even number) 48 d 57 6 CODABAR 1 k 48 d 57, 65 d1 68, 36, 43, 45, 46, 47, 58 7 CODE93 1 k d CODE128 2 k d CODE32 8 k 9 48 d TG2460 emulation

23 Formato 2 m BARCODE SySTEM No. OF CHARACTERS REMARKS 65 UPC-A 11 n d UPC-E 11 n d EAN13 (JAN) 12 n d EAN8 (JAN) 7 n 8 48 d CODE39 1 n d 57, 65 d 90, 32, 36, 37, 43, 45, 46, ITF 1 n d CODABAR 1 n d 57, 65 d1 68, 36, 43, 45, 46, 47, CODE93 1 n d CODE128 2 n d CODE32 8 n 9 48 d 57 If d is outside the speciied range, the printer prints the following message: BAR CODE GENERA- TOR NON OK! and processes the following data as normal data. If the horizontal size exceeds the printing area, the printer only feeds the paper. This command feeds as much paper as is required to print the bar code, irrespective of the line spacing speciied by 0x1B 0x32 or 0x1B 0x33. After printing the bar code, this command sets the print position at the beginning of the line. This command is not affected by print modes (bold, double strike, underline or character size), with the exception of upside-down mode and justiication. Formato 1 This command ends with a 0x00 code. When the bar code used is UPC-A or UPC-E, the printer prints the bar code data after receiving 11 (without check digit) or 12 ( with check digit) byte bar code data. When the bar code system used is EAN13, the printer prints the bar code after receiving 12 (without check digit) or 13 (with check digit) byte bar code data. When the system used is EAN8, the printer prints the bar code after receiving 7 (without check digit) or 8 (with check digit) byte bar code data. The number of data for ITF bar code must be even. When an odd number of data is input, the printer ignores the last received data. Formato 2 If n is outside the speciied range, the printer stops command processing and process the following data as normal data. TG2460 emulation 23

24 When to use CODE93: The printer prints an HRI character (o) as a start character at the beginning of the HRI character string. The printer prints an HRI character (o) as a stop character at the end of the HRI character string. The printer prints an HRI character (n) as a control character (0x00 to 0x1F and 0x7F). When to use CODE128: When using the CODE128 in this printer, take the following points into account for data transmission: The top of the bar code data string must be a code set selection character (CODE A, CODE B or CODE C) which selects the irst code set. Special characters are deined by combining two characters { and one character. The ASCII character { is deined by transmitting { twice consecutively. SPECIFIC CHARACTER DATA TRANSMISSION ASCII HEX DECIMAL SHIFT {S 7B, , 83 CODE A {A 7B, , 65 CODE B {B 7B, , 66 CODE C {C 7B, , 67 FNC1 {1 7B, , 49 FNC2 {2 7B, , 50 FNC3 {3 7B, , 51 FNC4 {4 7B, , 52 { {{ 7B, 7B 123, 123 [Default] 0x1D 0x48, 0x1D 0x66, 0x1D 0x68, 0x1D 0x77 24 TG2460 emulation

25 0x1D 0x77 <GS w> Set bar code width [Format] ASCII GS w n Hex 1D 77 n Decimal n [Range] 2 n 6 Sets the horizontal size of the bar code. n speciies the bar code width as follows: n MODULE WIDTH (mm) [Default] n = 3 TG2460 emulation 25

26 26 TG2460 emulation

27 CHARACTERS COMMANDS 0x1B 0x20 Set character right-side spacing <ESC SP> [Format] ASCII ESC SP n Hex 1B 20 n Decimal n [Range] 0 n 255 Sets spacing to right of character at [ n x horizontal or vertical motion units]. The spacing to the right of the character for double width mode is double that used for normal mode. When the characters are enlarged, the spacing to the right of the character is m (2 or 4) times the normal value. The horizontal and vertical motion units are speciied by the command 0x1D 0x50. Changing the horizontal or vertical motion does not affect the current right side spacing. The command 0x1D 0x50 can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum horizontal spacing amount. In standard mode, the horizontal motion unit is used. The maximum right side spacing is 255/200 inches. [Default] n = 0 0x1D 0x50 TG2460 emulation 27

28 0x1B 0x21 <ESC!> Set print mode [Format] ASCII ESC! n Hex 1B 21 n Decimal n [Range] 0 n 255 Selects the print mode using n (see following tables): BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 Character font A selected. On 01 1 Character font B selected RESERVED RESERVED 3 Off 00 0 Bold mode not selected. On 08 8 Bold mode selected. 4 Off 00 0 Double height mode not selected. On Double height mode selected. 5 Off 00 0 Double width mode not selected. On Double width mode selected. 6 Off 00 0 Script mode not selected. On Script mode selected. 7 Off 00 0 Underline mode not selected. On Underline mode selected The printer can underline all the characters, but it cannot underline the space set by commands 0x09, 0x1B 0x24, 0x1B 0x5C and 90 clockwise rotated characters. When the characters on the same line are enlarged to different heights, they are either aligned at the baseline or topline (see 0x1D 0x7E). This command resets the left and right margin at the default value (see 0x1D 0x4C, 0x1D 0x57). The command 0x1B 0x45 can also turn on/off bold mode. However, the setting of the last received command is effective. The command 0x1B 0x2D can also turn on/off underline mode. However, the setting of the last received command is effective The command 0x1B 0x34 can also turn on/off script mode. However, the setting of the last received command is effective. The command 0x1D 0x21 can select the character size. However,the setting of the last received command is effective. 28 TG2460 emulation

29 [Default] n = 0 0x1B 0x45, 0x1B 0x2D, 0x1B 0x34, 0x1D 0x21 TG2460 emulation 29

30 0x1B 0x2D <ESC -> Turn underline mode on/off [Format] ASCII ESC - n Hex 1B 2D n Decimal n [Range] 0 n 2 48 n 50 Turns underline mode on or off, based on the following values of n: n DESCRIPTION 0, 48 Turns off underline mode Turns on underline mode (1-dot thick) Turns on underline mode (2-dot thick) The printer can underline all characters but cannot underline the space set by 0x09 and right-side character spacing. The printer cannot underline 90 clockwise rotated characters and white/black inverted characters. When underline mode is turned off by setting the value of n at 0 or 48, the following data is not underlined. Underline mode can also be turned on or off by using 0x1B 0x21. Note, however, that the last command received is effective. [Default] n=0 0x1B 0x21 30 TG2460 emulation

31 0x1B 0x34 <ESC 4> Set / reset script mode [Format] ASCII ESC 4 n Hex 1B 34 n Decimal n [Range] 0 n 1 48 n 49 Turns script mode on or off, based on the following values of n: n FUNCTION 0, 48 Turns script mode off 1, 49 Turns script mode o The printer can print all characters in script mode. When script mode is turned off by setting the value n at 0 or 48, the data that follows is printed in normal mode. Script mode can also be turned on or off by using 0x1B 0x21. Note, however, that the last command received is effective [Default] n = 0 0x1B 0x21 TG2460 emulation 31

32 0x1B 0x45 <ESC E> Select bold mode [Format] ASCII ESC E n Hex 1B 45 n Decimal n [Range] 0 n 255 Turns bold mode On or Off. When the LSB of n is 0, bold mode is turned off. When the LSB of n is 1, bold mode is turned on. Only the LSB of n is effective. The command 0x1B 0x21 also turns bold mode on and off. In any case, the last command received is enabled. [Default] n = 0 0x1B 0x21 32 TG2460 emulation

33 0x1B 0x47 <ESC G> Select double-strike mode [Format] ASCII ESC G n Hex 1B 47 n Decimal n [Range] 0 n 255 Turns double-strike mode On or Off. When the LSB of n is 0, double-strike mode is turned off. When the LSB of n is 1, double-strike mode is turned on. Only the LSB of n is effective. The printer output is the same in double-strike mode and bold mode. [Default] n = 0 0x1B 0x45 TG2460 emulation 33

34 0x1B 0x52 <ESC R> Select international character set [Format] ASCII ESC R n Hex 1B 52 n Decimal n [Range] 0 n 12 Selects the international character set by setting n as in the following table: n HEX B 5C 5D 5E 60 7B 7C 7D 7E CHARACTERS SET 0 U.S.A. # [ \ ] ^ ` { } ~ 1 France # $ à ç ^ ` é ù è 2 Germany # $ Ä Ö Ü ^ ` ä ö ü b 3 United Kingdom [ \ ] ^ ` { } ~ 4 Denmark I # Æ Æ Å ^ ` æ f å ~ 5 Sweden # É Ä Ö Å Ü é ä ö å ü 6 Italy # \ é ^ ù à ò è ì 7 Spain I Pt i Ñ ^ ` ñ } ~ 8 Japan # [ ] ^ ` { } ~ 9 Norway # É Æ Æ Å Ü é æ f å ü 10 Denmark II # $ É Æ Æ Å Ü é æ f å ü [Default] n = 0 34 TG2460 emulation

35 0x1B 0x56 <ESC V> Set print mode rotated by 90 [Format] ASCII ESC V n Hex 1B 56 n Decimal n [Range] 0 n 1 48 n 49 Enable / disable print mode rotated by 90. n is used as follows: n FUNCTION 0, 48 Turns off 90 rotation mode 0,49 Turns on 90 rotation mode When underlined mode is turned on, the printer does not underline 90 rotated characters. All the same it s possible select the underline mode. Double-width and double-height commands in 90 rotation mode enlarge characters in the opposite directions from double-height and double-width commands in normal mode. This command is not available in Page mode. If this command is entered in Page mode, the printer all the same save the setting. Default] n = 0 0x1B 0x21, 0x1B 0x2D TG2460 emulation 35

36 0x1B 0x74 <ESC t> Select character code table [Format] ASCII ESC t n Hex 1B 74 n Decimal n [Range] n = 0, 19, 255 Selects a page n from the character code table, as follows: n PAGE 0 0 (PC437 [U.S.A., Standard Europe]) (PC858 for Euro symbol at position 213) 255 U.D.P. [Note] [Default] n = 0 See character code table For printing Euro symbol ( ), the command sequence is: 0x1B, 0x74, 0x13, 0xD5 36 TG2460 emulation

37 0x1B 0x7B <ESC {> Select upside-down printing mode [Format] ASCII ESC { n Hex 1B 7B n Decimal n [Range] 0 n 255 Turns upside-down printing mode on/off. When the LSB of n is 0, upside-down printing mode is turned off. When the LSB of n is 1, upside-down printing mode is turned on. Only the LSB of n is effective. This command is only enabled when input at the beginning of a line. In upside-down printing mode, the printer rotates the line to be printed by 180 and then prints it. [Default] n = 0 Upside-down printing Off ABCDEFG Paper outfeed direction Upside-down printing On ABCDEFG TG2460 emulation 37

38 0x1D 0x21 <GS!> Select character size [Format] ASCII GS! n Hex 1D 21 n Decimal n [Range] 0 n 255 Selects character height and width, as follows: Bits 0 to 3 : character height selection (see table 2). Bits 4 to 7 : character width selection (see table 1). Table1: Character width selection Table2: Character height selection HEX Decim. WIDTH HEX Decim. HEIGHT (normal) (normal) (double width) (double height) (quadruple width) (quadruple height) This command is effective for all characters (except HRI characters). If n is outside the deined range, this command is ignored. When characters are enlarged with different heights on one line, the are aligned at the baseline or topline (see 0x1D 0x7E). The character size can also be selected by the command 0x1B 0x21. However,the setting of the last received command is effective. [Default] n = 0 0x1B 0x21 38 TG2460 emulation

39 0x1D 0x42 <GS B> Turn white / black reverse printing on/off [Format] ASCII GS B n Hex 1D 42 n Decimal n [Range] 0 n 255 Turns white/black reverse printing mode on or off. When the LSB of n is 0, white/black reverse printing is turned off. When the LSB of n is 1, white/black reverse printing mode is turned on. Only the LSB of n is effective. This command is available for built-in characters and user-deined characters. This command does not affect bit image, downloaded bit image, bar codes, HRI characters and spacing skipped by 0x09, 0x1B 0x24 and 0x1B 0x5C. This command does not affect the space between lines. White/black reverse mode has a higher priority than underline mode. Even if underline mode is on, it is disabled (but not cancelled) when white/black reverse mode is selected. [Default] n = 0 TG2460 emulation 39

40 0x1D 0x7E <GS ~> Set superscript / subscript [Format] ASCII GS { } n Hex 1D 7E n Decimal n [Range] n = 0, 1, 48, 49 Sets superscript or subscript character position. n speciies the position as follows: n FUNCTION 0, 48 Subscript character position 1, 49 Superscript character position This command is executed if there are characters with different heights on the same line. [Default] n = 0 0x1B 0x21, 0x1D 0x21 40 TG2460 emulation

41 PRINTING COMMANDS 0x0A Print and line feed <LF> [Format] ASCII LF Hex 0A Decimal 10 Prints the data in the buffer and feeds one line, based on the current line spacing. This command sets the print position at the beginning of the line. [Default] 0x1B 0x32, 0x1B 0x33 TG2460 emulation 41

42 0x0D Print and line feed <CR> [Format] ASCII CR Hex 0D Decimal 13 [Default] When autofeed is 0x0D enabled, this command functions in the same way as 0x0A, otherwise it is ignored. This command sets the print position at the beginning of the line. See autofeed parameter on Setup. 0x0A 42 TG2460 emulation

43 0x1B 0x4A <ESC J> Print and feed paper [Format] ASCII ESC J n Hex 1B 4A n Decimal n [Range] 0 n 255 Prints the data in the print buffer and feeds the paper [ n * (vertical or horizontal motion unit) inches. After printing is over, this command sets the print starting position at the beginning of the line. The paper feed amount set by this command does not affect the values set by 0x1B 0x32 or 0x1B 0x33. The horizontal and vertical motion unit are speciied by 0x1D 0x50. The command GS P can change the vertical (and horizontal) motion unit. However, the value cannot be less than the minimum vertical movement amount. In standard mode, the vertical motion unit is used. The maximum paper feed amount is 31.8 mm. [Default] 0x1D 0x50 TG2460 emulation 43

44 0x1B 0x64 <ESC d> Print and feed paper n lines [Format] ASCII ESC d n Hex 1B 64 n Decimal n [Range] 0 n 255 Prints the data in the print buffer and feeds the paper n lines. This command sets the print starting position at the beginning of the line. This command does not affect the line spacing set by 0x1B 0x32 or 0x1B 0x33. The maximum paper feed amount is 200 lines. Even if a paper feed exceeding 200 lines is set, the printer only feeds the paper by 200 lines. [Default] 0x1B 0x32, 0x1B 0x33 44 TG2460 emulation

45 0x1B 0x78 <ESC x> Select speed / quality mode [Format] ASCII ESC x n Hex 1B 78 n Decimal n [Range] 0 n 2 Selects speed / quality mode. n FUNCTION 0 Draft mode (high speed) 1 Normal mode 2 High quality (low speed) In high quality mode (n= 2), the printer may be noisy. [Default] n = 1 TG2460 emulation 45

46 0x1D 0x7C <GS > Set printing density [Format] ASCII GS { } n Hex 1D 7C n Decimal n [Range] 0 n 4 48 n 52 Sets the printing density. n speciies the printing density as follows: n PRINTING DENSITy 0, 48-50% 1, % 2, 50 0 % 3, % 4, % The printing density is cleared at default value when the printer is reset or the power is turned off. [Default] n = 2 46 TG2460 emulation

47 STATUS COMMANDS 0x10 0x04 Transmission of status in real time <DLE EOT> [Format] ASCII DLE EOT n Hex n Decimal 16 4 n [Range] 1 n 4 n =17 20 n 21 Transmits in real time the selected status of the printer speciied by n according to the following parameters: n = 1 n = 2 n = 3 n = 4 n = 17 n = 20 n = 21 transmit printer status transmit off-line status transmit error status transmit paper roll sensor status transmit paper status transmit Full Status transmit printer ID. This command is executed even when the reception buffer is full. The status is transmitted whenever the data sequence 0x10 0x04 n is received. [Default] TG2460 emulation 47

48 n=1: Printer status BIT OFF/ON HEX Decimal FUNCTION RESERVED RESERVED RESERVED 3 Off 00 0 On-line On 08 8 Off-line RESERVED RESERVED RESERVED RESERVED n=2: Off-line status BIT OFF/ON HEX Decimal FUNCTION RESERVED RESERVED 2 Off 00 0 Print head down (no paper jam) On 04 4 Print head up (paper jam) 3 Off 00 0 Paper is not being fed by FEED button On 08 8 Paper is being fed by FEED button RESERVED 5 Off 00 0 No paper end stop On Printing stops due to paper end 6 Off 00 0 No error On Error RESERVED 48 TG2460 emulation

49 n=3: Error status Bit Off/On Hex Decimal FUNCTION RESERVED RESERVED RESERVED 3 Off 00 0 No auto-cutter error On 08 8 Auto-cutter error 4 On RESERVED 5 Off 00 0 No irreversible error On Irreversible error 6 Off 00 0 No auto-recoverable error On Auto-recoverable error RESERVED n=4: Paper roll sensor status BIT OFF/ON HEX Decimal FUNCTION RESERVED RESERVED 2, 3 Off 00 0 Paper is detected by the near paper end sensor On 0C 12 Paper end sensor not present or near paper end RESERVED 5, 6 Off 00 0 Paper is detected by the paper end sensor On Paper end is detected by the paper end sensor RESERVED TG2460 emulation 49

50 n=17: Paper status BIT OFF/ON HEX Decimal FUNCTION RESERVED RESERVED 2 Off 00 0 Motor not running On 04 8 Motor running RESERVED RESERVED 5 Off 00 0 Paper in On Paper end RESERVED RESERVED n=20: Full Status ( 6 bytes) 1 Byte = 0x10 (DLE) 2 Byte = 0x0F 3 Byte = Paper Status BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 Paper in On 01 1 Paper end RESERVED 2 Off 00 0 Paper in On 04 4 Near paper end RESERVED RESERVED RESERVED RESERVED RESERVED 50 TG2460 emulation

51 4 Byte = User Status BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 Print head down On 01 1 Print head up 1 Off 00 0 Cover down On 02 2 Cover up RESERVED 3 Off 00 0 Motor running (paper run) On 08 8 Motor not running (paper stand still) RESERVED 5 Off 00 0 FEED key not pressed On FEED key pressed 6 Off 00 0 PRINT key not pressed On PRINT key pressed RESERVED 5 Byte = Recoverable Error Status BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 Print head temperature normal On 01 1 Print head overheated RESERVED RESERVED 3 Off 00 0 Power supply voltage in range On 08 8 Power supply voltage out of range 4 Off 00 0 Receiving timeout not reached On Receiving timeout reached 5 Off 00 0 Acknowledge command On Not acknowledge command error 6 Off 00 0 Paper OK On Paper jam RESERVED TG2460 emulation 51

52 6 Byte = Unrecoverable Error Status BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 No auto-cutter error On 01 1 Auto-cutter error RESERVED 2 Off 00 0 No RAM error On 04 4 RAM error 3 Off 00 0 No EEPROM error On 08 8 EEPROM error RESERVED RESERVED RESERVED RESERVED 52 TG2460 emulation

53 0x1B 0x76 <ESC v> Transmit paper status [Format] ASCII ESC v Hex 1B 76 Decimal [Range] Transmits the current paper sensor status upon receiving this command. This command is executed immediately, even when the reception buffer is full (Busy ). The status to be transmitted is shown in the table below: BIT OFF/ON HEX Decimal FUNCTION 0,1 Off 00 0 Near paper end sensor: Paper present On 03 3 Near paper end sensor: Near paper end 2,3 Off 00 0 Paper end sensor: Paper present On (0C) (12) Paper end sensor: Paper end 4 Off 00 0 Fixed to Off RESERVED RESERVED 7 Off 00 0 Fixed to Off [Default] 0x10 0x04 TG2460 emulation 53

54 0x1D 0x72 <GS r> Transmit status [Format] ASCII GS r n Hex 1D 72 n Decimal n [Range] n = 1, n = 49 Transmits the status speciied by n as follows: n FUNCTION 1, 49 Transmits paper sensor status (same as 0x1B 0x76) BIT OFF/ON HEX Decimal FUNCTION 0, RESERVED RESERVED 2,3 Off 00 0 Paper end sensor: paper present On 0C 12 Paper end sensor: paper not present 4 Off 00 0 Fixed to Off RESERVED RESERVED 7 Off 00 0 Fixed to Off This command is executed when the data is processed in the reception buffer. There may therefore be a time lag between receiving the command and transmitting the status, depending on the status of the reception buffer. [Default] 0x10 0x04, 0x1B 0x75, 0x1B 0x76 54 TG2460 emulation

55 LINE SPACING COMMANDS 0x1B 0x30 <ESC 0> Select 1/8-inch line spacing [Format] ASCII ESC 0 Hex 1B 30 Decimal Selects 1/8-inch line spacing. [Default] 0x1B 0x32, 0x1B 0x33 TG2460 emulation 55

56 0x1B 0x32 <ESC 2> Select 1/6-inch line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal Selects 1/6 inch line spacing. [Default] 0x1B 0x30, 0x1B 0x33 56 TG2460 emulation

57 0x1B 0x33 <ESC 3> Set line spacing using minimum units [Format] ASCII ESC 3 n Hex 1B 33 n Decimal n [Range] 0 n 255 [Default] Sets the line spacing at [ n * (vertical or horizontal motion unit)] inches. Horizontal and vertical motion units are speciied by the command 0x1D 0x50. Changing the horizontal or vertical motion unit does not affect the current line spacing. The command 0x1D 0x50 can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum vertical movement amount. In standard mode, the vertical motion unit is used. The maximum line spacing is n = 255 (~ 32mm). n = 32 (1/6 inch) 0x1B 0x30, 0x1B 0x32, 0x1D 0x50 TG2460 emulation 57

58 58 TG2460 emulation

59 PRINTING POSITION COMMANDS 0x08 Moving back of one character <BS> [Format] ASCII BS Hex 08 Decimal 8 Moves print position to previous character. This command can put two characters at the same position. [Default] TG2460 emulation 59

60 0x09 Horizontal tabs <HT> [Format] ASCII HT Hex 09 Decimal 9 Moves the print position to the next horizontal tab position. This command is ignored if the next horizontal tab position has not been set. If the next horizontal tab is outside the print area, the printer will print the entire contents of the print buffer, then proceed with the processing of the horizontal tabs from the beginning of the following line. The horizontal tabs are set through the command 0x1B 0x44. [Default] 0x1B 0x44 60 TG2460 emulation

61 0x18 Cancel print data buffer <CAN> [Format] ASCII CAN Hex 18 Decimal 24 Deletes all the print data in the current print buffer. This command sets the print position at the beginning of the line. [Default] TG2460 emulation 61

62 0x1B 0x44 <ESC D> Set horizontal tab position [Format] ASCII ESC D n1...nk NUL Hex 1B 44 n1...nk 00 Decimal n1...nk 0 [Range] 1 n k 32 [Default] Sets the horizontal tabs. n speciies the number of columns for setting a horizontal tab from the beginning of the line. k indicates the total number of horizontal tabs to be set. The horizontal tab position is stored as a value of [character width x n] measured from the beginning of the line. The width of the character includes the space to the right of the character and double width characters are set with a width which is double that of normal characters. This command cancels the previous horizontal tab setting. When setting n = 8, the print position is moved to column 9 by sending 0x09. Up to 32 tab positions can be set ( k = 32). Any data exceeding the 32 tabs is processed as normal data. Transmit [ n ] k in ascending order and put a code 0 NUL at the end. When [ n ] k is less than or equal to the preceding value [ n ] k-1, tab setting is inished and the following data is processed as normal data. 0x1B 0x44 0x00 cancels all horizontal tab positions. The previously speciied horizontal tab positions do not change, even if the character width changes. The default tabs are at intervals of 8 characters (columns 9, 17, 25, ) for the A Font when the space to the right of the character is 0. 0x09 62 TG2460 emulation

63 0x1B 0x5C <ESC \> Set relative print position [Format] ASCII ESC \ nl nh Hex 1B 5C nl nh Decimal nl nh [Range] 0 nl nh 255 Sets the print starting position based on the current position by using the horizontal or vertical motion unit. This command sets the distance from the current position to [( nl+ nh * 256) * (horizontal or vertical motion unit)]. Any setting that exceeds the printable area is ignored. When the starting position is speciied by n motion units to the right: nl + nh * 256 = n When the starting position is speciied by n motion units to the left (negative direction) use the complement of 65536: nl + nh * 256 = n If setting exceeds printing area width, left or right margin is set to default value. The horizontal and vertical motion units are speciied by 0x1D 0x50. The command 0x1D 0x50 can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum horizontal movement amount. In standard mode, the horizontal motion unit is used. [Default] 0x1D 0x24, 0x1D 0x50 TG2460 emulation 63

64 0x1B 0x61 <ESC a> Select justiication [Format] ASCII ESC a n Hex 1B 61 n Decimal n [Range] 0 n 2 48 n 50 Aligns all the data in one line in the position speciied. n selects the type of justiication as follows: n JUSTIFICATION 0, 48 Left justiication 1, 49 Centring 2, 50 Right justiication This command is only enabled if input at the beginning of the line. The lines are justiied within the speciied printing area. The spaces set by the commands 0x09, 0x1B 0x24 and 0x1B 0x 5C remain justiied as per the previously set mode. [Default] n = 0 Left justiication Central justiication ABC ABCD ABCDE ABC ABCD ABCDE Right justiication ABC ABCD ABCDE 64 TG2460 emulation

65 0x1D 0x4C <GS L> Set left margin [Format] ASCII GS L nl nh Hex 1D 4C nl nh Decimal nl nh [Range] 0 nl, nh 255 Sets the left margin. The left margin is set at [(nl + nh * 256) * (horizontal motion unit)] inches. Printable area Left margin Printing area width This command is enabled only at the beginning of the line. If the setting exceeds the printable area, the maximum value of the printable area is used. If left margin + printing area width is greater than printable area, then printing area width is set at maximum value. The horizontal and vertical motion units are speciied by 0x1D 0x50. Changing the horizontal or vertical motion unit does not affect the current left margin. The command 0x1D 0x50 can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum horizontal movement amount and it must be expressed in even units of the minimum horizontal movement amount. [Default] If Font A : nl = nh = 0 If Font B : nl =14 nh = 0 0x1D 0x50, 0x1D 0x57 TG2460 emulation 65

66 0x1D 0x57 <GS W> Set printing area width [Format] ASCII GS W nl nh Hex 1D 57 nl nh Decimal nl nh [Range] 0 nl, nh 255 Sets the printing area width to the area speciied by nl and nh. The left margin is set at [(nl + nh * 256) * (horizontal motion unit)] inches. Printable area Left margin Printing area width This command is only enabled at the beginning of the line. If right margin is greater than printable area, then the printing area width is set at maximum value. If printing area width = 0, then it is set at maximum value. The horizontal and vertical motion unit are speciied by 0x1D 0x50. Changing the horizontal or vertical motion unit does not affect the current left margin. The command 0x1D 0x50 can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum horizontal movement amount and it must be expressed in even units of the minimum horizontal movement amount. [Default] If Font A : nl = 192 nh = 1 If Font B : nl =164 nh = 1 0x1D 0x4C, 0x1D 0x50 66 TG2460 emulation

67 BIT-IMAGE COMMANDS 0x1B 0x2A <ESC *> Set bit image mode [Format] ASCII ESC * m nl nh d1...dk Hex 1B 2A m nl nh d1...dk Decimal m nl nh d1...dk [Range] m = 0, 1, 32, 33 0 nl nh 1 0 d 255 Selects a bit image-mode using m for the number of dots speciied by nl and nh, as follows: m Mode Vertical direction Horizontal direction (*1) N dots DPI DPI N data (k) 0 8 dots single density nl + nh x dots double density nl + nh x dots single density (nl + nh x 256) x dots double density (nl + nh x 256) x 3 The commands nl and nh indicate the number of horizontal dots in the graphic image. The nl and nh indicate the number of dots of the bit image in the horizontal direction. The number of dots is calculated by nl + nh * 256. If the bit image data exceeds the number of dots to be printed on a line, the excess data is ignored. d indicates the bit image data. Set a corresponding bit to 1 to print dot or to 0 not to print dot. If the value of m is out of the speciied range, nl and the data following are processed as normal data. If the width of the printing area set by the commands 0x1D 0x4C and 0x1D 0x57 is less than the width required by the data sent with the command 0x1B 0x2A, the excess data is ignored. To print the bit image use commands 0x0A, 0x0D, 0x1B 0x4A or 0x1B 0x64. After printing a bit image, the printer returns to normal data processing mode. This command is not affected by bold, double-strike and underline (etc.) print modes, only by upsidedown mode. TG2460 emulation 67

68 The relationship between the bit image and the dots to be printed is as follows: 8 dot image 24 dot image MSB d1 d4 d7 MSB d1 d2 d3 Bitimage data d2 d5 d8 Bitimage data LSB d3 d6 d9 LSB Print data Print data [Default] 68 TG2460 emulation

69 0x1B 0xFA Print graphic bank (448 * 584 dots) [Format] ASCII ESC 0xFA n xh xl yh yl Hex 1B FA n xh xl yh yl Decimal n xh xl yh yl [Range] 1 n 2 0 xh, xl, yh, yl 255 Prints the graphics bank from lash or ram. n selects the bank as follows: n FUNCTION 1 Print lash bank logo 1 2 Print lash bank logo xl + xh * 256 speciies the starting dot line ( 1 862). yl + yh * 256 speciies the number of lines to print. If (xl + (xh * 256)) > 584 the printer does not execute the command. If ( xl + ( xh * 256) + yl +( yh * 256 )) > 584 the printer only prints xl + ( xh * 256 ) + 1 dotlines. [Default] To print logo 1 from lash bank dotline 100 to dotline 299, send: 0x1B 0xFA 0x01 0x00 0x64 0x00 0xC7 TG2460 emulation 69

70 70 TG2460 emulation

71 MACRO FUNCTION COMMANDS 0x1D 0x3A <GS :> Start / end macro of deinition [Format] ASCII GS : Hex 1D 3A Decimal Starts or ends macro deinition. Macro deinition starts when this command is received during normal operation. When the command 0x1D 0x5E is received during macro deinition, the printer ends the macro deinitions and clears all deinitions. Macro not deined when the power is turned on. The deined contents of the macro are not cleared by the command 0x1B 0x40. Therefore, 0x1B 0x40 can be included in the contents of the macro deinitions. If the printer receives the command 0x1D 0x3A again immediately after previously receiving 0x1D 0x3A, the printer remains in the macro undeined state. The contents of the macro can be deined up to 1024 bytes. If the macro deinition exceeds 1024 bytes, the excess data is not not stored. [Default] 0x1D 0x5E TG2460 emulation 71

72 0x1D 0x5E <GS ^> Execute macro [Format] ASCII GS ^ r t m Hex 1D 5E r t m Decimal r t m [Range] 0 r, t m 1 Executes a macro. r speciies the number of times to execute the macro. t speciies the waiting time for executing the macro. The waiting time is t * 100 msec. for every macro execution. m speciies macro executing mode: When the LSB of m = 0, the macro executes r times continuously at the interval speciied t. When the LSB of m = 1, after waiting for the period speciied by t, the LED indicator blinks and the printer waits for the FEED button to be pressed. After the button is pressed, the printer executes the macro once. The printer repeats the operation r times. This command lasts for a period of (t * 100 msec.) after a macro is executed by t. If this command is received while a macro is being deined, the macro deinition is aborted and the deinitions cleared. If the macro is not deined or if r is 0, nothing happens. When the macro is executed by pressing the FEED button (m = 1), the paper can not be fed by using the FEED button. [Default] 0x1D 0x3A 72 TG2460 emulation

73 MECHANISM CONTROL COMMANDS 0x1B 0x69 <ESC i> Total cut [Format] ASCII ESC i Hex 1B 69 Decimal This command enables cutter operation; if there is no cutter, a disabling lag is set any subsequent cutting commands will be ignored. The printer waits until all the paper movement commands have been completed before executing total cut. [Default] TG2460 emulation 73

74 0x1C 0xC0 0x34 Total cut and automatic paper moving back [Format] ASCII FS 0xC0 4 Hex 1C C0 34 Decimal This command enables cutter operation and executes a total cut and automatic paper moving back; if there is no cutter, a disabling lag is set any subsequent cutting commands will be ignored. The printer waits until all the paper movement commands have been completed before executing total cut. [Default] 74 TG2460 emulation

75 ANTI-JAMMING COMMANDS 0x1C 0xC1 Enable/disable automatic anti-jamming movement [Format] ASCII FS 0xC1 n Hex 1C C1 n Decimal n [Range] n = 0x00, 0x01, 0x30, 0x31 This command enables or disables the automatic anti-jamming movement that must be performed when the inspection door is lifted. The command works as described in the following table according to the n value: n 0x00, 0x30 0x01, 0x31 FUNCTION Disable the anti-jamming movement at the lift of the inspection door Enable the anti-jamming movement at the lift of the inspection door [Default] disabled TG2460 emulation 75

76 0x1D 0xDC Perform the anti-jamming movement [Format] ASCII GS 0xDC Hex 1D DC Decimal [Range] This command performs the anti-jamming movement regardless of the settings of the command 0x1C 0xC1 and the position of the inspection door. [Default] 0x1C 0xC1 76 TG2460 emulation

77 MISCELLANEOUS COMMANDS 0x1B 0x3D <ESC => Select device [Format] ASCII ESC = n Hex 1B 3D n Decimal n [Range] 0 n 255 Selects the device to which the host computer sends data, using n as follows: BIT OFF/ON HEX Decimal FUNCTION 0 Off 00 0 Printer disabled On 01 1 Printer enabled RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED When the printer is disabled, it ignores all transmitted data until the printer is enabled by this command. [Default] n = 1 TG2460 emulation 77

78 0x1B 0x40 Inizialize the printer [Format] ASCII Hex 1B 40 Decimal Clears the data in the print buffer and resets the printer mode to the mode that was in effect when the power was turned on. The data in the reception buffer is not cleared. The macro deinitions are not cleared. [Default] 78 TG2460 emulation