RocketRAID esata 6G HBA Series Boot Single Installation. Guide.

Transcription

1 RocketRAID esata 6G HBA Series Boot Single Installation Guide. Overview: This installation guide provides step and step instructions on how to configure the RocketRAID esata 6G storage to support booting to Mac OS X. This guide also provides trouble shooting tips when problems occur. Part 1 What is a Boot Single Configuration? Part 2 Pre requisite for Boot Single Configuration. Part 3 Hardware Installation Steps and Verification Steps Part 4 Software Package Installation and Verification Guide Part 5 Ready for the Experience

2 Part 1 What is a Boot Single? A Boot Single is moving the onboard Mac OS X boot drive to the RocketRAID esata 6G series controller or cloning the Mac OS X boot drive to another single hard disk drive. Part 2 Pre Requisite for Boot Single Configuration Overview The RocketRAID esata 6Gb/s series controller support booting to Mac OS X 10.5.x and above. Boot Single configuration include moving the boot drive to the RocketRAID esata 6G series controller or cloning the boot drive to single hard drive. This document will include the installations steps to configure and setup your hardware to support Boot Single to Mac OS X. The hardware and software pre requests are listed below: RocketRAID esata 6Gb/s series HBA

3 RocketRAID esata 6Gb/s 32/64bit EFI ROM image RocketRAID esata 6Gb/s for Mac drivers Mac Pro system 2006 to Present Multiple bay esata external storage Mac OS X 10.5.x and above 3 rd party clone software (clone onboard boot OS to Single Hard Drive) System Requirements Mac Pro Hardware: Intel based Mac with an available PCIe 2.0 or 1.0 slot capable of supporting an x4 (4 lane) length PCIe card. For optimal performance, use a PCIe 2.0 slot running at x4 speeds or greater. Slot recommendations for the RocketRAID esata 6G series controller. Mac Pro Model Core / CPU Speed GHz EFI Slot Number 2006 Quad Core / 2.0, 2.66, bit 3, Eight Core / bit 3, Quad Core / bit 2,3, Eight Core/ 2.8, 3.0, bit 2,3, Quad Core / 2.66/2.93/ bit 2,3, Eight Core / 2.26, 2.66, bit 2,3, Quad Core / 2.9, bit 2,3, Six Core / bit 2,3, Eight Core / bit 2,3, Twelve Core / 2.66, bit 2,3,4 Operating System: Mac OS X 10.5.x Note: A 32 or 64 bit EFI rom image is needed on the RocketRAID esata 6G series controller to support booting to Mac OS X. Refer to the above table load the correct EFI rom image to support your Mac Pro system. Tip: The 32 or 64 bit EFI rom image is found in the CD of the RocketRAID esata 6G series controller and it is also available for download on the website. Before, installing the RocketRAID esata 6G series controller make sure the computer is turned off and unplugged from its power source. Take appropriate electrostatic discharge precautions: Your computer is a static sensitive device. It is susceptible to invisible damage if not

4 protected during installation. We recommend proper grounding by using a grounding strap. Make sure to work in a clean and static free area, and avoid wearing clothing that retains static charges. Part 3 Hardware Installation and Verification Before installing the RocketRAID esata 6G series controller Make sure computer is turned off and unplugged from its power source Take appropriate electrostatic discharge precautions:. Remove the PCIe slot cover. Gently insert the RocketRAID esata 6G series controller into the PCIe slot and secure the bracket to the computer chassis according to your chassis specifications. After installing the RocketRAID esata 6G series controller, restart your computer. After your computer has started, insert the Driver & Software Installation Disc to install the necessary drivers for your computer s operating system. Hardware Verification Verifying the RocketRAID esata 6G series controller is installed into the Mac Pro system: Step 1: Click on About this Mac Step 2: Click on More Info Step 3: Click on System Report Step 4: Click on PCI Cards Step 5: The RocketRAID esata 6G series controller will be identified as RAID CONTOLLER. Step 6: Verify the RocketRAID esata 6G HBA is detected and no drivers are installed. In Mac OS X 10.5.x and 10.6.x the Driver Installed will be No. Once you have verified that the RocketRAID esata 6G series controller is detected you can proceed to the Driver and Software Installation.

5 Troubleshooting Tip: If the RocketRAID esata 6G series controller is not detected please try the following troubleshooting tips. Step 1: Shut down the Mac Pro system then remove and insert the RocketRAID esata 6G series controller then follow the steps from Hardware Verification. Step 2: If Step 1 fails, then insert the RocketRAID esata 6G series controller into a different PCIe slot. Step 3: If Step 2 fails, try the RocketRAID esata 6G series controller in another Mac Pro system. In Mac OS X 10.7.x the Drive Installed will be reported as Yes for the RocketRAID esata 6G series controller.

6 Part 4 Driver and Software Installation The RocketRAID esata 6G series controller comes with a disc containing the drivers and software for Mac Pro system. For the latest drivers and software visit the product page for the RocketRAID esata 6G series controller on Mac OS X 10.x Once you have installed the RocketRAID esata 6G series controller and booted into your Mac, follow these instructions to install the drivers and the RocketRAID esata 6G series controller software: 1. Insert the RocketRAID esata 6G Card Install Disc into your Mac and navigate to the Mac OS X folder. 2. Double click on the file to mount the disc image containing the Mac OS X software and drivers. 3. Double click on the installer package to start the installation process. 4. Follow the on screen steps to complete the installation process and you will be prompted to restart your computer. Verify Software Installation Step 1: Click on About this Mac Step 2: Click on More Info

7 Step 3: Click on System Report Step 4: Click on PCI Cards Step 5: The RocketRAID esata 6G series controller will be identified as RAID CONTOLLER. Step 6: Verify the RocketRAID esata 6G HBA is detected and Driver Installed is Yes. Note: Once Driver Installed is verified as Yes, the WebGUI is also be installed,too.because the driver and WebGUI are in one package. You can just start the browser to log in WebGUI. Troubleshooting Tip: If the after installing the software package and the Driver Installed is still No, please try the following troubleshooting tips. Step 1: Confirm that you have the RocketRAID esata 6G series controller software package and not another HighPoint RocketRAID series controller that support Mac OS X. Step 2: Run the uninstall script, reboot the Mac Pro system and reinstall the RocketRAID esata 6G series controller software once more. Mac OS X 10.7.x software Installation

8 Note: Since the driver for the RocketRAID esata 6G series controller is embedded into Mac OS X 10.7.x, you will only need to install the HPT esata web GUI for Mac 10.6 which can also be applied to Mac 10.7.x. Once it is confirmed that the driver is installed and web GUI is installed you can now proceed to log into the web GUI to create a RAID array. Note:Remember to flash EFI BIOS before cloning. Part 5 Ready to Experience Log into web GUI Log into the web GUI by entering opening a browser and entering the following URL Troubleshooting Tip: If you are not able to login to the URL, please check previous troubleshooting steps to verify that the driver is install and that the RocketRAID esata 6G series controller is detected.

9 Note: Any single HDD attached to the RocketRAID esata 6G series controller will be detected automatically. Cloning Boot OS Use 3 rd party software utility to clone boot drive to a single hard disk drive ttached to the RocketRAID esata 6G series controller. Once the clone has completed you can select the single hard disk drive attached to the RocketRAID esata 6G series controller as the boot device. Note: There are two methods to select the boot device. First: During boot up, hold down the alt option key and select the boot device attached to the RocketRAID esata 6G series controller as the bootup device. Second: In System Preferences

10 Select the Startup Disk and choose the boot volume. Restart the system to boot from the RocketRAID esata 6G series controller.