Board Options. Modified by Phil Loughhead on 27-Jan Parent page: PCB Dialogs. Old Content - visit altium.com/documentation
|
|
- Amberlynn Hunt
- 5 years ago
- Views:
Transcription
1 Board Options Old Content - visit altium.com/documentation Modified by Phil Loughhead on 27-Jan-2016 Parent page: PCB Dialogs
2 The Board Options Dialog. Summary Board Options dialog allows the designer to control special drawing features for PCB Sheets, and object snap behavior. To learn more about cursor snap behavior, refer to the Unified Cursor-Snap System page.
3 Access The Board Options dialog can be accessed from PCB Editor (Design» Board Options), or Right click in PCB Editor, choose Options» Board Options in context menu. Right click in PCB Library Editor, choose Library Options... from the popup menu. Right click in PCB Editor, choose Options» Sheet... from the popup menu. Options/Controls Measurement Unit Unit - Select the default measurement units for the current PCB document here. Click to select from either metric (mm) or imperial (mil) units. Default units are used to display any distance related information on screen or in reports. The default units are always used if a units suffix (mm or mil) is not entered when specifying any distance related information in any dialog editing fields. Many dialogs feature a direct units toggle at the top-left corner (also accessed through CTRL + Q) that will convert between metric and imperial measurement in that dialog. Designator Display The Display Physical Designators option is defined by the Designator Format on the Multi-Channel tab from the Option for Project dialog. The physical designators are unique, eg. R1_CH1. The Display Logical Designators option only shows the designators (eg. R1) which were specified from the schematics. The logical designators show up on the PCB document, printouts and Gerbers. All other outputs such as BOM will always use the unique physical designator format. Route Tool Path Layer - Choose a layer from drop-down list as routing path for routing tool. Sheet Position X - Enter a X (horizontal) coordinate for the bottom left corner of the sheet here. This distance is measured from the absolute origin, which is the bottom left corner of the workspace. The distance can be defined in either metric or imperial units regardless of the default units (which are determined by themeasurement Unit setting). To specify the units when entering a size, add the mm or mil suffix to the value. The PCB position does not change with sheet position as the PCB position is referenced from the absolute origin. Enable the Origin Marker checkbox to see the absolute origin reference point. This Origin Marker is accessed from the View Options page of the View Configurations dialog (Design» Board Layers & Colors).
4 Y - Enter a Y (vertical) coordinate for the bottom left corner of the sheet here. This distance is measured from the absolute origin, which is the bottom left corner of the workspace. The distance can be defined in either metric or imperial units regardless of the default units (which are determined by themeasurement Unit setting). To specify the units when entering a size, add the mm or mil suffix to the value. The PCB position does not change with sheet position as the PCB position is referenced from the absolute origin. Enable the Origin Marker checkbox to see the absolute origin reference point. This Origin Marker is accessed from theview Options page of the View Configurations dialog (Design» Board Layers & Colors). Width - Enter a width for the sheet here. The sheet provides an area that emulates the traditional drawing sheet and is useful for placing information such as dimensions, notes and title blocks on. Information placed on mechanical layers can be linked to the sheet so that they only display when the sheet is being displayed. Sheet size can be defined in either metric or imperial units regardless of the default units (which are determined by the Measurement Unit setting). To specify the units when entering a size, add the mm or mil suffix to the value. Height - Enter a height for the sheet here. The sheet provides an area that emulates the traditional drawing sheet and is useful for placing information such as dimensions, notes and title blocks on. Information placed on mechanical layers can be linked to the sheet so that they only display when the sheet is being displayed. Sheet size can be defined in either metric or imperial units regardless of the default units (which are determined by the Measurement Unit setting). To specify the units when entering a size, add the mm or mil suffix to the value. Display Sheet - Enable to display the sheet. The sheet provides an area that emulates the traditional drawing sheet and is useful for placing information such as dimensions, notes and title blocks on. Information placed on mechanical layers can be linked to the sheet so that they only display when the sheet is being displayed. You can set sheet size using the Width and Height fields and sheet position, relative to the absolute origin, using the X and Y fields. You can set the sheet related colors and layers linked to the sheet in the Board Layers And Colors page of the View Configurations dialog (Design» Board Layers & Colors). Auto-size to linked layers - Enable this option to automatically size the sheet to linked layers. Snap Options Snap To Grids - enable this option to allow the cursor to snap to the default cartesian grid defined for the board. Snap To Linear Guides - enable this option to allow the cursor to snap to manually placed linear Snap Guides. Snap To Point Guides - enable this option to allow the cursor to snap to manually placed point Snap Guides. Snap To Object Axis - enable this option to allow the cursor to snap to dynamic alignment guides created through proximity to the hotspot(s) of placed objects. Advanced/Simple - use this control to accessed advanced options for this feature. Snap To Object Hotspots - use this option to toggle whether the cursor can snap to the hotspot of placed objects when it is simultaneously close (on both the X and Y axes) to such a hotspot. Range - use this field to define the electrical grid range. This value determines how close
5 you need to get to an electrical object's hot-spot before the cursor will snap to it, even if the object is not on the Snap Grid. In general, you would set the Electrical Grid range to a setting somewhat less than the Snap Grid. For example, if the Snap Grid is set to 50mil, an appropriate Electrical Grid range would be 30mil. Enter a value directly, or choose one of the predefined values available from the field's drop-down. Snap On All Layers - enable this option to allow the cursor to snap to any electrical object on any visible layer. When this option is disabled, the cursor will only recognize and snap to objects placed on the currently selected layer. When in Single Layer mode, the Electrical Grid will only apply to electrical objects on the current layer. Snap To Board Outline - enable this option to allow the cursor to snap to the board outline. This option can be useful for dimensioning a PCB, particularly when the board corners or vertices are off the Snap Grid. Snap To Arc Centers - enable this option to allow the cursor to snap to the centers of placed arc objects. Advanced Options - Snap To Object Axis Near Range - use this field to specify the distance the cursor can be from an enabled object, inside which that object's hotspot will cause the cursor to snap to a system-generated dynamic alignment guide. Near Objects - Enable this option, and the required design objects to be used as snap point sources as the cursor is moved near to them. Far Objects - enable this option, and the required design objects to be used as snap point sources when the cursor is further away from an object, beyond the specified Near Range. An enabled object's hotspot will continue to cause the cursor to snap to a system-generated dynamic alignment guide, at this greater distance. Additional Buttons Grid - click this button to access the Grid Manager dialog, from where to manage the default and user defined snap grids for the board. Guides - click this button to access the Snap Guide Manager dialog, from where a range of manual snap guides and snap points for the board can be defined and managed. Link To Vault This can only be accessed in PCB Library Editor.
6 Target Vault - Choose the vault which the PCB Library will be released to. Target Folder - Choose the folder in the target Vault where the PCB Library will be released. Lifecycle Definition - Make sure which Lifecycle definition will be used when the PCB Library is released to the Vault. Revision Naming - To determine which naming scheme will be used when the PCB Library is released to the Vault.
7 Buttons Grids - This command opens the Grid Manager dialog, from where local customized grids can be defined and managed, as well as the default snap grid for the board. Guides - This command opens the Snap Guide Manager dialog, from where a range of manual snap guides and snap points for the board can be defined and managed. Source URL:
Unified Cursor-Snap System (PCB)
Unified Cursor-Snap System (PCB) Old Content - visit altium.com/documentation Modified by on 21-Nov-2013 Related Videos Advanced Snap Management Cursor snap is the process whereby the physical mouse cursor's
More informationLibrary Editor Workspace
Library Editor Workspace Modified by Jason Howie on Oct 1, 2014 Other Related Resources Schematic - Grids (Preferences) Grids (Commands) Parent page: Sch Dialogs The Library Editor Workspace dialog. Summary
More informationDrill Table. Summary. Modified by Phil Loughhead on 16-Jun Parent page: PCB Dialogs
Drill Table Old Content - visit altium.com/documentation Modified by Phil Loughhead on 16-Jun-2015 Parent page: PCB Dialogs The Drill Table Dialog. Summary A standard element required for manufacture of
More informationComponent. Modified by Jason Howie on Feb 13, Parent page: PCB Dialogs. Other Related Resources Component (Object) The Component Dialog.
Component Modified by Jason Howie on Feb 13, 2015 Other Related Resources Component (Object) Parent page: PCB Dialogs The Component Dialog. Summary The Component dialog is used to edit the properties of
More informationPublished on Online Documentation for Altium Products (https://www.altium.com/documentation)
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > 3D Body A New Era for Documentation Modified by Phil Loughhead on Jun 16, 2017 The 3D Body Dialog. Summary
More information3D Body. Modified by Jason Howie on 8-Oct Parent page: PCB Dialogs. Other Related Resources 3D Body (Object)
3D Body Modified by Jason Howie on 8-Oct-2016 Other Related Resources 3D Body (Object) Parent page: PCB Dialogs The 3D Body Dialog. Summary The 3D Body dialog allows you to modify the attributes of an
More informationBaseline dimension objects are available for placement in the PCB Editor only, by clicking Home
Baseline Dimension Modified by Jason Howie on 24-Oct-2014 Parent page: Dimension A placed Baseline Dimension. Summary A baseline dimension is a group design object. It allows for the dimensioning of a
More informationSchematic Editing Essentials
Summary Application Note AP0109 (v2.0) March 24, 2005 This application note looks at the placement and editing of schematic objects in Altium Designer. This application note provides a general overview
More informationPolygon Pour. Modified by Susan Riege on Aug 13, Parent page: PCB Dialogs. Other Related Resources Polygon Pour (Object)
Polygon Pour Modified by Susan Riege on Aug 13, 2018 Other Related Resources Polygon Pour (Object) Parent page: PCB Dialogs The Polygon Pour dialog in Solid mode, Hatched mode and None mode. Summary This
More informationPCB Design View. Contents
PCB Design View Contents Placing a Design View Defining the View Area Setting the Location and Scale of the Design View Defining the Title Interactively adjusting the Scale, Size and Focus of the Design
More informationBaseline dimension objects are available for placement in the PCB Editor only. Use one of the following methods to access a placement command:
Baseline Dimension Old Content - visit altium.com/documentation Modified by on 19-Nov-2013 Parent page: Objects A placed Baseline Dimension. Summary A baseline dimension is a group design object. It allows
More informationDrill Table. Summary. Availability. Modified by on 19-Nov Parent page: Objects
Drill Table Old Content - visit altium.com/documentation Modified by on 19-Nov-2013 Parent page: Objects The Drill Table presents a live summary of all drill holes present in the board. Summary A standard
More informationTutorial : First board in CircuitMaker.
Tutorial : First board in CircuitMaker. Objectives 1. Create a new project in CircuitMaker. 2. Design electronic circuit in CircuitMaker schematic editor. 3. Design a pcb board for your circuit in CircuitMaker
More informationComments. Summary. Modified by Rob Evans on Jun 10, Parent page: Workspace Manager Panels
Comments Modified by Rob Evans on Jun 10, 2015 Parent page: Workspace Manager Panels The Comments panel showing a collection of user comments for the currently active project. Summary The Comments panel
More informationCycle through three routing modes (ignore, avoid or push obstacle) Toggle electrical grid on/off
PCB Editor Shortcuts Old Content - visit altium.com/documentation Modified by on 13-Sep-2017 Parent article: Shortcut Keys PCB Editor Shortcuts + E + B + PAGE UP + PAGE DOWN Cycle through three routing
More informationRadial Diameter Dimension. Contents
Radial Diameter Dimension Contents Description Availability Placement Editing via an Associated Properties Dialog Editing via the PCB Inspector Panel Editing via the PCB List Panel Graphical Editing Notes
More informationThe user-defined grids can only be defined and managed from within the Grid Manager dialog.
Custom Local Grid Old Content - visit altium.com/documentation Modified by Admin on Nov 22, 2013 Parent page: Objects Cartesian and Polar-based local grids. Summary User-defined Cartesian and/or Polar-based
More informationLesson 5: Board Design Files
5 Lesson 5: Board Design Files Learning Objectives In this lesson you will: Use the Mechanical Symbol Editor to create a mechanical board symbol Use the PCB Design Editor to create a master board design
More informationPreparing the Board for Design Transfer. Creating and Modifying the Board Shape. Modified by Phil Loughhead on 15-Aug-2016
Preparing the Board for Design Transfer Old Content - visit altium.com/documentation Modified by Phil Loughhead on 15-Aug-2016 This article describes how to prepare the new PCB file so that it is ready to
More information3D Body. Summary. Modified by Admin on Sep 13, Parent page: Objects
3D Body Old Content - visit altium.com/documentation Modified by Admin on Sep 13, 2017 Parent page: Objects A sphere, a cylinder and 4 extruded rectangles have been used to create the 3D body for an LED.
More informationPublished on Online Documentation for Altium Products (
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > SnapSTEPModel Using Altium Documentation Modified by Jason Howie on Apr 11, 2017 Parent page: PCB Commands
More informationFrom Idea to Manufacture - Driving a PCB Design through CircuitStudio
From Idea to Manufacture - Driving a PCB Design through CircuitStudio Modified by Susan Riege on 13-Sep-2018 Welcome to the world of electronic product development in Altium's world-class electronic design
More informationString. Summary. Availability. PCB Editor. PCB Library Editor. Modified by on 20-Nov Parent page: Objects
String Old Content - visit altium.com/documentation Modified by on 20-Nov-2013 Parent page: Objects Placed String objects. Summary A string is a primitive design object. It places text on the selected
More informationPart. Summary. Modified by Susan Riege on Aug 5, Parent page: Objects
Part Old Content - visit altium.com/documentation Modified by Susan Riege on Aug 5, 2016 Parent page: Objects Related Resources Net Ties and How to Use Them (PDF) The Part represents the actual physical
More informationSchematic Libraries, Models and Integrated Libraries
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Главная > A Look at Creating Library Components Using Altium Documentation Modified by Jason Howie on Apr 11,
More informationUsing the PCB Component Wizard
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > PCB Component Wizard Using Altium Documentation Modified by Phil Loughhead on Jun 19, 2017 The PCB Component
More informationFrom Idea to Manufacture - Driving a PCB Design through SOLIDWORKS PCB
From Idea to Manufacture - Driving a PCB Design through SOLIDWORKS PCB Modified by Jason Howie on 24-Oct-2017 Welcome to the world of electronic product development in Altium's world-class electronic design
More informationSystemVue 2011 Fundamentals (version ) LAB EXERCISE 1. SystemVue Basics
SystemVue 2011 Fundamentals (version 1-2012) LAB EXERCISE 1 SystemVue Basics This lab exercise introduces the basic use model of SystemVue, including using the built-in templates, running analyses and
More informationParameter. Parent page: Objects. Mod. ifi. Rob. Eva 25- Aug -20. Old Content - visit altium.com/documentation
Parameter Old Content - visit altium.com/documentation Mod ifi ed by Rob Eva ns on 25- Aug -20 16 Parent page: Objects Parameters are used for components, documents and projects to add detail information
More informationTo learn more about a command, dialog, object or panel, press F1 when the cursor is over that item.
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) 主页 > 从理念到制造 通过Altium Designer推动PCB设计 Altium技术文档新纪元 Modified by Jun Chu on Apr 26, 2018 Welcome to the world
More informationGerber X2 Setup. Summary. Modified by Jason Howie on Mar 10, Parent page: WorkspaceManager Dialogs
Gerber X2 Setup Modified by Jason Howie on Mar 10, 2015 Other Related Resources Gerber Setup (Dialog) Parent page: WorkspaceManager Dialogs The Gerber X2 Setup dialog. Summary This dialog allows the designer
More informationTutorial - Getting Started with PCB Design
Tutorial - Getting Started with PCB Design Old Content - visit altium.com/documentation Modified by Phil Loughhead on 3-Aug-2016 Welcome to the world of electronic product development environment in Altium
More informationBoot Camp-Special Ops Challenge Quiz
1. What s the key difference between a panel and dialog window? a. There is none b. Panels must be closed in order to continue editing, whereas dialogs can be left open c. Dialogs must be closed in order
More informationMET 107 Drawing Tool (Shapes) Notes Day 3
MET 107 Drawing Tool (Shapes) Notes Day 3 Shapes: (Insert Tab Shapes) Example: Select on the rounded rectangle Then use the mouse to position the upper left corner and produce the size by dragging out
More informationPCB Rules and Violations
PCB Rules and Violations Old Content - visit altium.com/documentation Modified by on 6-Nov-2013 Parent page: Panels Browse, edit and interactively view design rules and their associated violations. Summary
More informationPADS-PowerPCB 4 Tutorial (with Blazeroute)
PADS-PowerPCB 4 Tutorial (with Blazeroute) PADS-PowerPCB is the ultimate design environment for complex, high-speed printed circuit boards. PROCEDURE FOR SIMULATION IN SCHEMATICS 1. Importing Design Data
More informationPCB Design Training Module
PCB Design Training Module Document Version 1.01, December 4, 2006 Software, documentation and related materials: Copyright 2006 Altium Limited. All rights reserved. You are permitted to print this document
More informationPublished on Online Documentation for Altium Products (
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > Coverlay Polygon Using Altium Documentation Modified by Phil Loughhead on Oct 24, 2018 Parent Page: PCB
More informationThe Department of Construction Management and Civil Engineering Technology CMCE-1110 Construction Drawings 1 Lecture Introduction to AutoCAD What is
The Department of Construction Management and Civil Engineering Technology CMCE-1110 Construction Drawings 1 Lecture Introduction to AutoCAD What is AutoCAD? The term CAD (Computer Aided Design /Drafting)
More informationExercise 1. Section 2. Working in Capture
Exercise 1 Section 1. Introduction In this exercise, a simple circuit will be drawn in OrCAD Capture and a netlist file will be generated. Then the netlist file will be read into OrCAD Layout. In Layout,
More informationQuestions? Page 1 of 22
Learn the User Interface... 3 Start BluePrint-PCB... 4 Import CAD Design Data... 4 Create a Panel Drawing... 5 Add a Drill Panel... 5 Selecting Objects... 5 Format the Drill Panel... 5 Setting PCB Image
More informationExploring CircuitMaker
Exploring CircuitMaker Modified by Phil Loughhead on 2-Jun-2015 Getting Started Driving a PCB Design through CircuitMaker Project Management Component Management Variants Parent page: CircuitMaker Documentation
More informationCreating Buttons and Pop-up Menus
Using Fireworks CHAPTER 12 Creating Buttons and Pop-up Menus 12 In Macromedia Fireworks 8 you can create a variety of JavaScript buttons and CSS or JavaScript pop-up menus, even if you know nothing about
More informationIntegrating MCAD Objects and PCB Designs
Integrating MCAD Objects and PCB Designs Summary Altium Designer offers high levels of interaction with MCAD data. This means you can import, manipulate and check mechanical design elements against your
More informationDefining Board Regions and Bending Lines
Defining Board Regions and Bending Lines Old Content - visit altium.com/documentation Modified by on 29-Nov-2016 Related Videos Bending Lines Layer Stack Regions A Board Region is the term used to describe
More informationRelease Highlights for BluePrint-PCB Product Version 3.0
Release Highlights for BluePrint-PCB Product Version 3.0 Introduction BluePrint V3.0 Build 568 is a rolling release, containing defect fixes for 3.0 functionality. Defect fixes for BluePrint V3.0 Build
More informationWorking with Plan Production ObjectsChapter1:
Chapter 1 Working with Plan Production ObjectsChapter1: The lessons in this chapter guide you through the processes of creating and working with plan production objects. Plan production objects include
More informationAltium Designer Viewer - Viewing PCB Documents
Altium Designer Viewer - Viewing PCB Documents Old Content - visit altium.com/documentation Modified by on 6-Nov-2013 In Altium Designer Viewer PCB documents are opened in the PCB Editor. The tools and
More informationWorking with the Board Insight System
Working with the Board Insight System Old Content - visit altium.com/documentation Modified by on 29-Jul-2014 Board Insight is a configurable system of features that give you complete control over viewing
More informationGenerating a Custom Bill of Materials
Generating a Custom Bill of Materials Old Content - visit altium.com/documentation Modified by on 6-Nov-2013 This tutorial describes how to use the Report Manager to set up a Bill of Materials (BOM) report.
More informationL E S S O N 2 Background
Flight, Naperville Central High School, Naperville, Ill. No hard hat needed in the InDesign work area Once you learn the concepts of good page design, and you learn how to use InDesign, you are limited
More information6/23/2009. AutoCAD Chapter 3 Objectives. Line Command. Coordinate Entry Methods. Rectangular Coordinate System
Chapter 3 Objectives AutoCAD 2009 CHAPTER 3 JUNE 23, 2009 Use the correct entry format when entering numbers Demonstrate how to end or cancel commands Describe and use several point entry methods Draw
More informationGetting Started. In This Chapter
Getting Started In This Chapter 2 This chapter introduces concepts and procedures that help you get started with AutoCAD. You learn how to open, close, and manage your drawings. You also learn about the
More informationQuickTutor. An Introductory SilverScreen Modeling Tutorial. Solid Modeler
QuickTutor An Introductory SilverScreen Modeling Tutorial Solid Modeler TM Copyright Copyright 2005 by Schroff Development Corporation, Shawnee-Mission, Kansas, United States of America. All rights reserved.
More informationParent page: PCB Panel
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) 主页 > PCB Library Using Altium Documentation Modified by Annika Krilov on Apr 11, 2017 Parent page: PCB Panel
More informationUsing Coordinate Systems
Using Coordinate Systems In This Chapter 5 As you draw you use the coordinate system to specify points in the drawing. You can locate and use your own movable user coordinate system (UCS) for working on
More informationP3e REPORT WRITER CREATING A BLANK REPORT
P3e REPORT WRITER CREATING A BLANK REPORT 1. On the Reports window, select a report, then click Copy. 2. Click Paste. 3. Click Modify. 4. Click the New Report icon. The report will look like the following
More informationText strings are available for placement in both Schematic and Schematic Library Editors by:
Text String Old Content - visit altium.com/documentation Modified by on 20-Nov-2013 Parent page: Objects A placed Text String. Summary A text string (also referred to as an annotation) is a non-electrical
More informationLAB # 2 3D Modeling, Properties Commands & Attributes
COMSATS Institute of Information Technology Electrical Engineering Department (Islamabad Campus) LAB # 2 3D Modeling, Properties Commands & Attributes Designed by Syed Muzahir Abbas 1 1. Overview of the
More informationIntroduction Make a plan with tool Rectangle Measurements Toolbar Enter Return Measurements Toolbar Measure Protractor
Introduction Open SketchUp, and an empty file appears. You are looking at the red-green plane, and the blue axis (vertical) is pointing toward you. By default, you are in the Line tool, as indicated by
More informationFitted with modified component parameters, such as the component's value.
Variants Modified by Susan Riege on Sep 4, 2018 Parent page: Exploring CircuitStudio The ability to create variations of the same base design is a real strength of CircuitStudio, and a tremendous productivity
More informationProtel 99 Installation Notes
Protel 99 Installation Notes Frozen Content Modified by Admin on Nov 21, 2013 Protel 99 SE Service Pack 6 Information Installation Notes To install the Service Pack run the downloaded file and follow the
More informationGetting Started With Excel
Chapter 1 Getting Started With Excel This chapter will familiarize you with various basic features of Excel. Specific features which you need to solve a problem will be introduced as the need arises. When
More informationTable Basics. The structure of an table
TABLE -FRAMESET Table Basics A table is a grid of rows and columns that intersect to form cells. Two different types of cells exist: Table cell that contains data, is created with the A cell that
More informationStarting Excel application
MICROSOFT EXCEL 1 2 Microsoft Excel: is a special office program used to apply mathematical operations according to reading a cell automatically, just click on it. It is called electronic tables Starting
More informationTechnical Documentation Version 7.3 Output
Technical Documentation Version 7.3 Output These documents are copyrighted by the Regents of the University of Colorado. No part of this document may be reproduced, stored in a retrieval system, or transmitted
More informationCreating a Multi-board Assembly
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) 主页 > Creating the Physical Multi-board Assembly Using Altium Documentation Modified by Susan Riege on Mar 23,
More informationPublished on Online Documentation for Altium Products (
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > Using Altium Documentation Modified on Nov 15, 2016 Overview This interface is the immediate ancestor
More informationGetting_started_EN (Ind : 3) 06/01/2014. elecworks. Getting Started
Getting_started_EN (Ind : 3) 06/01/2014 elecworks Getting Started 1 Start with elecworks This document has been made to help you in starting elecworks. It summarizes the features available. If you would
More informationIntroduction to NI Multisim & Ultiboard
George Washington University School of Engineering and Applied Science Electrical and Computer Engineering Department Introduction to NI Multisim & Ultiboard Dr. Amir Aslani 8/20/2017 2 Outline Design
More informationAnsoft HFSS Windows Screen Windows. Topics: Side Window. Go Back. Contents. Index
Modifying Coordinates Entering Data in the Side Windows Modifying Snap To Absolute Relative Each screen in divided up into many windows. These windows can allow you to change the coordinates of the model,
More informationInteractively Routing a Net
Interactively Routing a Net Old Content - visit altium.com/documentation Modified by on 18-Nov-2013 Interactive Routing is more than placing down track objects to join the dots (pads). Altium Designer
More informationA Guide to Autodesk Maya 2015
A Guide to Autodesk Maya 2015 Written by Mitchell Youngerman Table of Contents Layout of Toolbars...pg 1 Creating Objects...pg 2 Selecting & Deselecting Objects...pg 3 Changing Perspective... pg 4 Transforming
More informationTutorial - Integrating MCAD Objects and PCB Designs
Tutorial - Integrating MCAD Objects and PCB Designs Old Content - visit altium.com/documentation Mod ifi ed by Adm in on Jul 14, 201 4 Altium Designer offers high levels of interaction with MCAD data.
More informationSPARK. User Manual Ver ITLAQ Technologies
SPARK Forms Builder for Office 365 User Manual Ver. 3.5.50.102 0 ITLAQ Technologies www.itlaq.com Table of Contents 1 The Form Designer Workspace... 3 1.1 Form Toolbox... 3 1.1.1 Hiding/ Unhiding/ Minimizing
More informationLibraries. Modified by Rob Evans on 15-Oct Related pages: Component Management in CircuitMaker
Libraries Modified by Rob Evans on 15-Oct-2015 Related pages: Component Management in CircuitMaker From Idea to Manufacture - Driving a PCB Design through CircuitMaker Parent page: Panels Use the Libraries
More informationAutoCAD 2009 Configuration for MUS
AutoCAD 2009 Configuration for MUS NOTE: The following steps do not apply to AutoCAD 2006 or earlier versions. These steps must be done before attempting to use MicroScribe Utility Software (MUS) with
More informationGetting Started. The main tasks described in this section are the following:
Getting Started Getting Started Before getting into the detailed instructions for using Interactive Drafting workbench, the following tutorial aims at giving you a feel of what you can do with the product.
More informationImpress Guide Chapter 11 Setting Up and Customizing Impress
Impress Guide Chapter 11 Setting Up and Customizing Impress This PDF is designed to be read onscreen, two pages at a time. If you want to print a copy, your PDF viewer should have an option for printing
More informationTo be able to create charts that graphically represent your worksheet data, you will: Create column charts on chart sheets by using the F11 key.
L E S S O N 1 Creating charts Suggested teaching time 55-65 minutes Lesson objectives To be able to create charts that graphically represent your worksheet data, you will: a b c Create column charts on
More informationTexas School for the Blind and Visually Impaired. Using The Drawing Tools in Microsoft Word 2007 for Tactile Graphic Production
Texas School for the Blind and Visually Impaired Outreach Programs 1100 West 45 th Street Austin, Texas, 78756 Using The Drawing Tools in Microsoft Word 2007 for Tactile Graphic Production Developed by:
More informationProNest 2010 Version 9.2
ProNest 2010 Version 9.2 What s New Released August 17, 2011 What s New in ProNest 2010 (v9.2) 1 Enhancements The following enhancements are available in the ProNest 9.2 release: Color-Filled Parts Parts
More informationVersion Software Update Details Release Date 22-Sep Problem Fixes in Version
Version 12.0.6 Software Update Details Release Date 22-Sep-2009 Problem Fixes in Version 12.0.6 This is the final roll-up patch for Version 12. No further updates will be issued for this version. Add Shape
More informationComponent Templates. The Component Template Item Type. Modified by Jason Howie on 31-May-2017
Component Templates Old Content - see latest equivalent Modified by Jason Howie on 31-May-2017 Altium Vault 2.5, in conjunction with Altium Designer 15.1, brings support for creating and defining Component
More informationCollaborating between Altium Designer and SOLIDWORKS
Collaborating between Altium Designer and SOLIDWORKS Old Content - visit altium.com/documentation Mod ifi ed by Jas on How ie on 21- Oct -20 16 Parent page: MCAD Co-Designer: SOLIDWORKS This documentation
More informationDesktop Studio: Charts. Version: 7.3
Desktop Studio: Charts Version: 7.3 Copyright 2015 Intellicus Technologies This document and its content is copyrighted material of Intellicus Technologies. The content may not be copied or derived from,
More informationUsing OrCAD Layout Plus A Simple Guide
Using OrCAD Layout Plus A Simple Guide Written by Jose Cabral September 2006 Revised by Nithin Raghunathan 1 SKETCH THE CIRCUIT YOU WISH TO LAYOUT SKETCH THE LAYOUT COM J1 OUTPUT +12 COM -12 COM INPUT
More informationPublished on Online Documentation for Altium Products (https://www.altium.com/documentation)
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > Sheet Symbol Using Altium Documentation Modified by Susan Riege on Apr 11, 2017 Parent page: Schematic
More informationPoster-making 101 for 1 PowerPoint slide
Poster-making 101 for 1 PowerPoint slide Essential information for preparing a poster for the poster printer 1. Poster size: You will be creating a single large slide in PowerPoint. 2. Before adding any
More informationWord 3 Microsoft Word 2013
Word 3 Microsoft Word 2013 Mercer County Library System Brian M. Hughes, County Executive Action Technique 1. Insert a Text Box 1. Click the Insert tab on the Ribbon. 2. Then click on Text Box in the Text
More informationCECOS University Department of Electrical Engineering. Wave Propagation and Antennas LAB # 1
CECOS University Department of Electrical Engineering Wave Propagation and Antennas LAB # 1 Introduction to HFSS 3D Modeling, Properties, Commands & Attributes Lab Instructor: Amjad Iqbal 1. What is HFSS?
More informationCOMSC-031 Web Site Development- Part 2. Part-Time Instructor: Joenil Mistal
COMSC-031 Web Site Development- Part 2 Part-Time Instructor: Joenil Mistal Chapter 9 9 Creating Pages with Frames You can divide the display area of a Web browser into multiple panes by creating frames.
More informationPlacing Spaces. Let Me Try! Before you begin. The following files are needed for this Let Me Try exercise: M_c04_archi_spaces_rmp2015.
Placing Spaces Before you begin The following files are needed for this Let Me Try exercise: For Imperial: For Metric: c04_archi_spaces_2016.rvt M_c04_archi_spaces_rmp2015.rvt To access the files from
More informationRandy H. Shih. Jack Zecher PUBLICATIONS
Randy H. Shih Jack Zecher PUBLICATIONS WWW.SDCACAD.COM AutoCAD LT 2000 MultiMedia Tutorial 1-1 Lesson 1 Geometric Construction Basics! " # 1-2 AutoCAD LT 2000 MultiMedia Tutorial Introduction Learning
More informationJust Enough Eclipse What is Eclipse(TM)? Why is it important? What is this tutorial about?
Just Enough Eclipse What is Eclipse(TM)? Eclipse is a kind of universal tool platform that provides a feature-rich development environment. It is particularly useful for providing the developer with an
More informationGetting Started with PCB Design
Getting Started with PCB Design Summary Tutorial TU0117 (v1.2) April 13, 2005 This introductory tutorial is designed to give you an overview of how to create a schematic, update the design information
More information2008 년안산일대디지털정보통신학과 CAD 강의용자료 PADS 2007
2008 년안산일대디지털정보통신학과 CAD 강의용자료 PADS 2007 1 Learning the PADS User Interface What you will learn: Modeless Commands Panning & Zooming Object Selection Methods Note: This tutorial will use PADS Layout to
More informationSNS Vibe Data Processor
SNS Vibe Data Processor The SNS Vibe Data Processor in GPSQL determines duplicates based on the 'Selected_Point' field in an SNS table. To start, select a query which isolates the data you want to examine.
More informationSmarTools. Feature Summary
SmarTools Feature Summary Product Description SmarTools, an MDL application, is a collection of productivity tools for those organisations involved in schematic drafting. Supported Platforms SmarTools
More information1 In the Mini Window Editor, double-click phase 1 (GF-Wall-External) to make it current:
1 This Quick Start tutorial introduces you to the basics of creating an intelligent drawing using the BIM components supplied with MicroGDS 2010. Here we demonstrate how to construct the external walls
More information