P/N : M INSTRUCTION MANUAL. USB/AUX/BLUETOOTH/iPod AM/FM RADIO RB-02 WITH

Transcription

1 P/N : M INSTRUCTION MANUAL RB-02 USB/AUX/BLUETOOTH/iPod WITH AM/FM RADIO

2 Contents Important Note: Before operating the unit, please read this manual thoroughly and retain it for future reference. Please refer to the main vehicle user manual section Features of Your Vehicle for general information regarding radio reception, care and use of the vehicle mounted antenna, and care and use of media (USB etc.). The operation of the steering wheel remote controls shown in the main vehicle user manual are not relevant to the radio model depicted in this user manual. Contents: 1. General Controls 2. Steering Wheel Controls 3. AM/FM Radio 4. USB Player 5. USB Music Player 6. USB Photo Player 7. ipod Player 8. AUX Input 9. My Music 10. Bluetooth Wireless Technology 11. BT AUDIO player 12. BT Call 13. Voice Recognition 14. Set up 15. Firmware Upgrade 16. Warnings and Precautions 17. Product and Warranty Service 18. SPECIFICATIONS Page 03 Page 08 Page 09 Page 13 Page 16 Page 19 Page 21 Page 25 Page 27 Page 31 Page 36 Page 39 Page 44 Page 45 Page 59 Page 61 Page 61 Page 62 1

3 Apple CarPlay Feature This instruction manual provides the user with basic information to confidently operate the Apple CarPlay feature. Please refer to the main instruction manual for this audio set for operation of other functions. It is recommended that the user regularly visits the official Apple website to become aware of changes to Apple CarPlay features by visiting Apple CarPlay requires iphone 5 and ios 8.0 or later. 1. Activating Apple CarPlay 3. Using Siri Voice Function Connect the cable between the iphone and the USB socket fitted to the car. Apple CarPlay mode starts and the main menu is displayed (pictured below). NOTE: Apple CarPlay may not operate until the iphone is unlocked. If a Bluetooth device is connected, it will be disconnected when Apple CarPlay is active. Apple CarPlay mode must be switched on (see next page). Apple CarPlay must be enabled in the iphone settings; it is enabled by default. Check the iphone Settings>General>Restrictions. To use ipod mode on an Apple CarPlay capable iphone change the restrictions or switch off Apple CarPlay mode. Momentarily press the VOICE button on the front panel of the audio set to activate the Siri voice recognition feature. When using Siri, speak clearly, toward the front of the audio unit. For best results, reduce the noise levels in the car cabin. It is not recommended to use the Hey Siri feature. Siri provides many valuable functions via voice control. See 4. Apple CarPlay Settings To alter Apple CarPlay settings related to this audio set, press the SETUP button on the front of the audio set front panel, then tap the Apple CarPlay icon shown. 2. Operating Apple CarPlay Setup Screen Apple CarPlay Settings Screen Apple CarPlay Main Menu Tap the desired icon on the Apple CarPlay main menu (see above). To return to the Apple CarPlay main menu, tap the home icon on the lower right hand side on Apple CarPlay screens. During operation of some Apple CarPlay functions, (for example guidance) it is possible to listen to AM/FM tuner by pressing the RADIO button on the front of the audio set or by pressing the MODE button on the steering wheel remote control. A uxiliary input mode may also be used concurrently with some Apple CarPlay functions. The MODE button on the steering wheel remote control switches between Apple CarPlay music sources (if playing) and the audio set s AM/FM tuner and auxiliary input (if connected). Display or Button Description Home icon Changes the screen to main menu (home) selection. CarPlay OFF / ON buttons OFF: ipod mode will operate. ON: Apple CarPlay mode will operate. Note: Apple CarPlay mode and ipod mode cannot be operated simultaneously. ALT. Vol Control Sets the level of the Apple CarPlay navigation guidance voice in relation to the currently selected volume level of the audio set. 2 3

4 2

5 General Steering wheel controls 1. General 1.1 Front Panel 1.2 General Controls 1.3 Main Menu (Home) Screen 1.4 Media Menu Screen Steering Wheel Controls 08 3

6 General 1. General 1.1 Front Panel TUNE Knob (Press or Rotate) Selects the radio frequency, media tracks and sound setting screen. VOL Knob (Press or Rotate) Selects the volume level, power on/off, clock and dark screen on/off. MEDIA Button (Press) Selects the media menu screen and changes mode. RADIO Button (Press) Selects the radio mode and changes radio band. PHONE Button (Press) Selects phone connection, keypad, call list and contacts. SETUP Button (Press) Selects the settings menu, system info and emmc memory screen. GUI Graphic User Interface for each function. Bluetooth Microphone Microphone used in Bluetooth handsfree or voice recognition mode. VOICE button (Press) Selects the voice recognition function in CarPlay and Bluetooth mode. Note: Before using the audio, remove the protective tape LCD from the LCD screen (if fitted). Operating the touch screen without removing the LCD protective tape will lead to abnormal operation. 4

7 General 1.2 General Controls TUNE Knob Searches the desired track in media mode. Searches the desired frequency in radio mode. (Manual Tuning) Press this knob to access the sound settings screen. Power On/Off, Volume Up/Down Knob Press this knob momentarily (less than 1 second) to turn the power on or off. Press and hold this knob to switch the display off or on. You can also press the MEDIA button to show the display. If display is off, sound is playing.(except power off mode). Turn this knob right or left to increase or decrease the volume level. The level will be shown on the display. After 3 seconds the display will return to the previous mode. MEDIA Button Press the MEDIA button to display the media menu screen. Change the mode by touching the desired media icon. RADIO Button Selects the radio mode or changes the radio wave band. The sequence of radio band selection: FM 1 FM 2 FM 3 AM VOICE Button Press the VOICE button to activate voice recognition of connected phone. For more information see the chapter in this manual titled Bluetooth and Car Play. PHONE Button Press the PHONE button to display the phone operation screen when the phone is connected via Bluetooth. If a phone is not connected, pressing the button displays the Bluetooth phone connection screen. If a phone is connected, press this button for more than 1 second to redial the last called number. If a call is connected, press the PHONE button to end the call. SETUP Button Press the SETUP button to display the setup screen. Select the desired setting category by touching the corresponding icon. For more information see the chapter in this manual titled Settings. GUI Screen Graphic user interface for each function. BT Microphone Microphone used for Bluetooth hands-free or voice recognition mode of connected phone. 5

8 General 1.3 Main Menu (Home) Screen To access the main menu screen, tap the Home icon at the top left hand side of the display. Radio: Selects radio mode. USB: Selects USB music or photo mode. ipod: Selects ipod mode. Connectivity: Selects smart phone tethering mode. AUX: Selects auxiliary input mode. My Music: Selects internally stored memory music mode. Bluetooth: Selects Bluetooth mode. Set Up: Selects setup mode. Notes: If an icon is greyed out, it is not available for selection as it may not be connected. 6

9 General 1.4 Media Menu Screen To access the media menu screen, press the MEDIA button on the front panel. Home: Selects the main menu screen. Music: Selects USB music mode. Photo: Selects USB photo mode. ipod: Selects ipod mode. AUX: Selects Auxilary mode. BT Audio: Selects Bluetooth audio mode. My Music: Selects internally stored memory music mode. Connectivity: Selects the smart phone tethering mode. [ X ]: Closes Media menu mode. Notes: a) Press the MEDIA button momentarily to display the media screen. Press the MEDIA button again to return to the last selected media mode. b) If a selection is not made selected within 6 seconds, the previous screen will be restored automatically. c) If an icon is greyed out, it is not available for selection as it may not be connected. 7

10 Steering Wheel Controls (if fitted) 2. Steering Wheel Controls VOLUME ( + / - ) button 1) Push the toggle switch toward + to increase the volume level. 2) Push the toggle switch toward - to decrease the volume level. 2.2 SEEK ( / ) button When in RADIO mode: 1) Press the SEEK Up button when SEEK up is operating to stop searching. 2) Press the SEEK Down button when SEEK down is operating to stop searching. 3) Press the SEEK buttons for more than 1 sec. to seek to the next / previous available radio station. When in MEDIA (USB / BT Audio / My Music) mode: 1) Press the SEEK buttons for less than 1 second to change to the next / previous track. 2) Pressing & holding the SEEK button for more than 1 second to CUE or REVIEW the current playing track. Note: a. The SEEK buttons may not operate when using some Bluetooth music players. b. CUE and REVIEW is not available when using BT AUDIO mode. 2.3 MODE button 1) Press the MODE button for less than 1 sec. to change to the next available mode. 2) The complete mode sequence for selection is shown below: FM 1 FM 2 FM 3 AM USB (MUSIC PHOTO) ipod AUX MY MUSIC BT AUDIO 3) Press the MODE button for more than 1 second to switch the HYUNDAI Bluetooth radio off. Note: Only those mode sources connected will be displayed and available for selection when using the Steering Wheel MODE button. 2.4 MUTE button 1) Press the MUTE button to switch the sound off. 2) Pressing again to restore the sound. 2.5 VOICE button (If fitted) Press the VOICE button to activate voice recognition of connected phone. 2.6 ON HOOK button (If fitted) HYUNDAI D-Audio is connected in phone. (in Bluetooth pairing status) 1) Press the ON HOOK button to switch phone screen. 2) Press the ON HOOK button to answer the phone. 2.7 OFF HOOK button (If fitted) HYUNDAI D-Audio is connected in phone. (in Bluetooth pairing status) Press the OFF HOOK button to hang up the phone.

11 AM/FM Radio 3. AM/FM Radio 3.1 AM/FM Radio Mode Screen 3.2 Selecting Radio Band 3.3 Searching Radio Stations 3.4 Best Station Memory 3.5 Preset Memory 3.6 Scan and Preset Scan

12 AM/FM Radio 3. AM/FM Radio 3.1 AM/FM Radio Mode Screen Display or Button Description Home icon Change the screen to main menu (home) selection. Radio / Time Displays the operating mode (FM1~FM3,AM) & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Band(FM1 / FM2 / FM3 / AM) button Touch button, select to wave band (FM1/FM2/FM3/AM). Playing / Preset frequencies & channel Displays the currently playing frequency Displays preset frequencies & channel numbers. Ch1 ~ Ch6 button The saved frequency by each.of preset channels (1 ~ 6). SEEK (Down / Up) icon Seek previous / next radio frequency automatically. SCAN button Seek broadcast frequency and listen for 5 sec. and seek next broadcast frequency until ending 1 cycle. BSM button Saves frequencies with superior reception to preset 6-buttons. P.SCAN button Displays frequencies are stored preset 6-buttons of currently band. Note: To display the radio menu screen, press the RADIO button on the front panel to display or touch the Radio icon on the main menu (home) screen or by pressing the steering wheel MODE button. 10

13 AM/FM Radio 3.2 Selecting Radio Bands 1) When the Radio screen is displayed, touch the desired radio band tab (FM1/FM2/FM3/AM). 2) Press the RADIO button to change the radio wave band. The sequence of selection is FM 1 FM 2 FM 3 AM 3.3 Searching Radio Stations 1) To manually tune to a radio station, turn the TUNE knob clockwise or anticlockwise. 2) To automatically seek for a radio station, tap the forward or backward icon soft button on the radio display screen. Note: a. Press the steering wheel SEEK up or down buttons for more than 1 second to seek to the next / previous available radio station. b. Only radios stations of acceptable signal strength will be selected when automatic seek is activated. If your desired station is not found, drive to another location and begin the seek tune again. 3.4 Best Station Memory (BSM) Tap the BSM soft button on the radio display screen to activate the BSM function. Note: a. Radio stations in the vicinity of the vehicle that are of acceptable reception quality are stored in the radio preset buttons (CH01~06) memory locations automatically. b. If less than six stations are found during the BSM function, the previously stored preset memories are retained in the higher numbered memory locations. c. Tap the BSM soft button to stop the function. 3.5 Preset Memory 1) To store the currently tuned station to a preset, touch and hold the desired soft button preset for more than a second. 2) To recall a preset memory, tap the desired soft button. Note: a. Each of the radio bands store six preset memories. b. When storing a station in preset memory, the previously store station is overwritten. c. A Beep sound is heard when the memory is stored. d. Preset station memories are lost if the vehicle battery is disconnected. 3.6 Scan and Preset Scan 1) Tap the SCAN soft key to begin a five seconds preview of each received radio station on the current chosen radio band. Tap the SCAN button again to stop the scan. 2) Tap the P.SCAN soft key to begin a five second preview of each preset memory radio station received on the current chosen radio band. Tap the P.SCAN button again to stop the scan. 11

14 12

15 USB Player 4 USB Player Important notes for the use of USB 4.1 USB Player Screen 4.2 Charging USB Player USB Music Player 5.1 USB Music Player Screen 5.2 Play or Pause 5.3 File Previous & Review 5.4 File Next & Cue 5.5 File Scan 5.6 File List 5.7 File Copying 5.8 Repeat Play 5.9 Random Play 5.10 Time Seek USB Photo Player 6.1 USB Photo Player Screen 6.2 File Zoom 6.3 File Scan 6.4 File Slide show 6.5 File Rotate 6.6 File List

16 USB Player 4. USB Player Important Notes: 1. USB devices should be disconnected from the at Engine start because USB external device can be damaged. 2. If you turn on & off vehicle engine during the connection of the USB external device, USB devices may not operate. 3. If it is not MP3, WMA files in a standard format, it can not play music. 4. Pay attention to static electricity when attaching or detaching USB device. 5. If the encrypted MP3 player connected to Audio Headunit, it does not recognize. 6. Depending on the USB external device, Audio Headunit can not be recognized. 7. At formatting USB external device, the USB device which is not 512 byte or 2048 byte can be recognized. 8. USB external device which is formatted with FAT 12/16/32 can be recognized. 9. In some cases of the USB device, there are compatibility issues, which Audio Headunit may not be operating normally. Please use it after confirming the operation in the vehicle. 10. Do not touch the body of a person or object in the USB connection. 11. If you repeat connection and disconnection of USB device in a short period of time, this can cause damage to the Audio headunit. 12. During playing file in USB device, do not disconnect USB device from audio headunit due to the possibility of damage on USB device. Make use of disconnection at Audio power off condition. 13. Depending on the type of USB device, memory size and the type of files, there can be time delay to recognize device. 14. Depending on the complex of USB memory and folder s trees, the message of ID3 tag or RPT/RDM can be displayed slowly. 15. Do not use USB device except music playing. 16. Charging via USB interface is not recommended due to the possibility of mal-function or damage on USB multi-media device. 17. Do not use USB hub or the extension cable for USB device connection because data loss can be happened. 18. In case of logical partition of memory in USB external device, it is only possible to play music in the top logical memory driver. Please put music file in the top logical memory driver. 19. In the connection of MP3 player, cellphone and digital camera, it might not operate normally. 20. USB memory except standard(metal cover type) USB can not guarantee the operation. 21. HDD type, CF, SD memory can not guarantee the operation. 22. DRM (Digital Rights Management) file can not be supported to play. 23. The USB memory sticks such as SD, CF type USB memory stick and adaptor type USB might not be detected by audio headunit. 24. USB memory stick such as USB HDD or poor connection type of USB can make contactless in USB interface of audio headunit. Do not use those USB memory sticks which can make damage on audio headunit. USB socket located lower on the center console, inside cover. 1) To play files using the USB connection, connect your USB device to the USB socket located lower on the center console. 2) When the USB memory device is connected, the HYUNDAI D-Audio will change to USB mode, display Reading and then USB mode playback will begin. 3) If another mode is selected, USB player may be resumed by pressing the MEDIA button on the HYUNDAI D-Audio or by pressing the MODE button on the steering wheel. 4) The HYUNDAI D-Audio display shows the file ID3 information. If the ID3 information is too long for the display, the display scrolls when touch that ID3 information. 14

17 USB Player 4.1 USB Player Screen USB - Music USB - Photo USB - List Note: When Using the USB Player a. If there are no compatible files found on the USB device, returns to the previous mode and displays There is no valid files. b. If the USB device is not compatible Reading Error will be displayed on the HYUNDAI D-Audio. c. Use of Multi-Card Reader devices may not work correctly. d. USB players will be recognized as storage devices by the HYUNDAI D-Audio. e. The HYUNDAI D-Audio is realize 2,000 files stored USB device. 4.2 Charging USB Player When a USB device is connected to the HYUNDAI D-Audio, the USB device will be charged whilst the vehicle ACC switch is ON. The HYUNDAI D-Audio does not need to be operating. Note: When Using the USB Socket for Charging a. Effective battery charging of USB devices using the USB socket cannot be assured. b. The power is available at the USB socket when the vehicle ignition switch is in the ACC position. The HYUNDAI D- Audio is not required to be operating. 4.3 MP3/WMA Information 1) The HYUNDAI D-Audio is able to play MP3 and WMA music files from a USB memory device. 2) MP3 is an abbreviation of Motion Picture Experts Group (MPEG) Audio layer-3. MP3 audio format files are typically only 1/10th the size of conventional CD DA audio files. Most MP3 files are created on a personal computer using special software. Additional text information such as track TITLE, ARTIST and ALBUM included in the audio track can be displayed on the HYUNDAI D-Audio. The sound quality of MP3 files varies depending on the settings used when the file was created. 3) Your HYUNDAI D-Audio plays most MP3 files. 4) WMA is an abbreviation of Windows Media Audio, an audio format developed by Microsoft Corporation. WMA is similar to MP3 with respect to size, sound quality and text display. WMA files are created using the Windows Media Player on a personal computer. 5) Your HYUNDAI D-Audio plays most WMA files. Note: a. The elapsed playing time shown on the display may not be correct when playing MP3 files encoded with variable bit rate (VBR). b. MP3 and WMA files encoded at bit rates lower than 128 KB/s will provide lower sound quality compared to conventional CD DA audio tracks. c. MP3 and WMA files with Digital Rights Management* (DRM) activated cannot be played on this car audio set. d. Only 32 character file names are displayed. e. Only FAT12, FAT16 and FAT32 file systems are supported. f. Only ID3 tags V1.1 and V2.2 are supported. Copyright: a. Copyright may exist on some audio program material. b. Please observe the copyright restrictions. c. For additional technical information, see the specifications page in this manual. 15

18 USB Player-Music 5. USB Music Player MP3 and WMA music files located on a compatible USB memory device can be played. 5.1 USB Music Player Screen Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. USB Music / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) FILE Informations Displays currently playing file information (Title, Artist, Album Name) RPT / RDM / Intro / Track No icon Executes play mode as repeat (all/one/folder) / random (off/all/folder). Plays for 10 seconds for each next track. Diplays currently playing / total track number. Playing / Total time Diplays currently playing / total time. Previous / Next icon Plays previous / next track. Play / Pause icon Plays or Pauses currently playing track. LIST button Displays file list within the USB device. COPY button: Changes the screen to copy confirmation. (Copies the currently playing file from USB to internal device memory.) The USB music player screen can be selected by pressing the MEDIA button, then tapping the Music icon on the media menu screen. The USB music player screen can also be selected using the MODE button on the steering wheel remote control. Note: a. A compatible USB memory device must be connected to the USB socket in the vehicle console in order for the USB music player to be activated. b. The Music and Photo icons on the media menu screen will be greyed out if no USB memory device or playable files are available. 16

19 USB Player - Music 5.2 Play or Pause 1) Touch the Play/Pause icon on the USB music player screen to begin playing the selected file. 2) Touch the Play/Pause icon on the USB music player screen to pause the playing file. 5.3 File Previous & Review 1) Tap the Back icon on the USB music player screen to select the previous file. 2) Tap and hold the Back icon on the USB music player screen to review the audio contents of the currently playing file. Releasing the icon will allow playback to resume. 5.4 File Next & Cue 1) Tap the Forward icon on the USB music player screen to select the next file. 2) Tap and hold the Forward icon on the USB music player screen to cue the audio contents of the currently playing file. Releasing the icon will allow playback to resume. Note: The Next and Previous functions can be operated by the steering wheel remote controls. Refer to the steering wheel control section for instructions. 5.5 File Scan 1) Tap the Headset icon on the USB music player screen to play the first 10 seconds of each file on the USB memory device. The Repeat icon will show a small A indicating All files are being playback scanned. When the desired file is found, tap the Headset icon or the Repeat icon to continue playing that file. 2) To scan the files in only the currently selected folder on the USB memory device, touch and hold the Headset icon for more than 1 second; the Repeat icon will show a small F, indicating Folder. 5.6 File List 1) Tap the LIST soft button on the USB music player screen to display the contents of the USB memory device. 2) Folders are selected by tapping the left or right arrow icons to the left of the currently selected folder name. 3) Files are selected by tapping the file name displayed on the screen. Slide the sliding position bar on the far right of the list screen to move files up and down for view. Note: a. Use the TUNE knob to quickly display all files on the USB memory device. b. When the desired file is shown, press the TUNE knob momentarily to begin playback of that file. c. The number of tracks on the USB memory device is shown on the USB music player screen. 17

20 USB Player - Music 5.7 Copying Files 1) Tap the COPY button on the USB music player screen to copy the currently playing file. 2) Once copying starts, the copy screen will be displayed. 3) Once copying is complete, the copy screen disappears. 4) The copied file is stored to the internal emmc (SD) memory and can be played within My Music mode. 5.8 Repeat Play 1) During USB or MyMusic play, tap the Repeat icon shown on the USB music player screen for less than 1 second. The Repeat icon will show a small 1 indicating that the currently playing file will play repeatedly. Playback of the same file will continue to repeat until the icon is tapped again. 2) Touch and hold the Repeat icon for more than 1 second. The icon will not show a small F indicating that playback of the currently selected folder will repeat. 5.9 Random Play 1) During USB music or MyMusic play, touch the Random icon for less than 1 second to play files on the USB in a random or shuffled order. 2) Touch and hold the Random icon for more than 1 second. The icon will not show a small F indicating that playback of the files in the currently selected folder will play in random order Time Seek 1) The progress of the currently playing files is displayed on screen as a thin orange line. Elapsed and total time is shown at each end of the progress line. 2) Tap anywhere on the progress line to change the play position. 18

21 USB Player - Photo 6 USB Photo Player Image files located on a USB memory device may be viewed on the screen. 6.1 USB Photo Player Screen Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. USB Photo / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the image & Info. Diplays currently playing folder name. Diplays currently playing file name. Shows the image currently playing. Zoom In / Out icon Zooms in or out the image by centre align. Previous / Next icon Shows the previous / next image. Slide show icon Shows the image one by one with effect. Rotate(Right) icon Rotates the image to right 90 degree. LIST button Displays file list within the USB device. The USB photo player screen can be selected by pressing the MEDIA button, then tapping the Photo icon on the media menu screen. The USB photo player screen can also be selected using the MODE button on the steering wheel remote control. Note: a. A compatible USB memory device must be connected to the USB socket in the vehicle console in order for the USB photo player to be activated. b. The Music and Photo icons on the media menu screen will be greyed out if no USB memory device or playable files are available. 19

22 USB Player - Photo 6.2 File Zoom In & Out Adjust the magnification of the photo image using the Plus or Minus soft buttons. 6.3 File Scan Tap the Next and Previous soft key icons to move through and display files in the currently selected folder. The chosen file will remain on the display indefinately. 6.4 File Slide show Tap the Film Strip soft button to begin the slide show. Each file will be displayed for 3 seconds, then progress to the next file and display it. Tap the screen during the slide show to stop on the currently selected file. 6.5 File Rotate Tap the 3/4 Circle icon on to rotate the image 90 degrees clockwise. 6.6 File List 1) Tap the LIST soft button on the USB photo viewer screen to display the contents of the USB memory device. 2) Folders are selected by tapping the left or right arrow icons to the left of the currently selected folder name. 3) Files are selected by tapping the file name displayed on the screen. Slide the sliding position bar on the far right of the list screen to move files up and down for view. Note: a. Use the TUNE knob to quickly display all files on the USB memory device. b. When the desired file is shown, press the TUNE knob momentarily to view that file. c. The number of files on the USB memory device is shown on the USB photo viewer screen. 20

23 ipod Player AUX Input 7. ipod Player Note: Directions for the use of ipod 7.1 ipod Music Player Screen 7.2 Play or Pause 7.3 Track Previous & Review 7.4 Track Next & Cue 7.5 Song Searching 7.6 Repeat Play 7.7 Random Play 7.8 Searching Files List AUX Input 8.1 Aux Connector 8.2 Aux Player Screen

24 ipod Player 7 ipod Player Note: Directions for the use of ipod. a. Please use the dedicated ipod cable for vehicle when playing music in ipod. b. During the connection between ipod and Audio headunit, ipod is charging at Acc On status. c. Not recommend to use the PC cable provided by Apple. d. Insert the terminals to the end of the jack so as not to interfere with communications. e. Unplug ipod cable in case of no connection of ipod since noise can be got into audio headunit. f. Depending ipod model and its software version, ID3 tag or RPR/RDM information can be displayed late. 7.1 ipod Music Player Screen Connect the ipod to the USB socket located lower on the centre console using the cable supplied with ipod (see to 4. USB Player ). Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. ipod / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ,BT,Phone Battery&Ant.,Volume) FILE Informations Displays currently playing file information (Title, Artist, Album Name) RPT / RDM / Track No icon Executes play mode as repeat (all/one) / random (on/off). Diplays currently playing / total track number. Playing / Total time Diplays currently playing / total time. Previous / Next icon Plays previous / next track. Play / Pause icon Plays or Pauses currently playing track. LIST button Displays file list within the ipod device. 22

25 ipod Player The ipod player screen can be selected by pressing the MEDIA button, then tapping the ipod icon on the media menu screen. The ipod player screen can also be selected using the MODE button on the steering wheel remote control. Note: a. A compatible ipod device must be connected to the USB socket in the vehicle console in order for the ipod player to be activated. b. The ipod icons on the media menu screen will be greyed out if no ipod device or playable files are available. 7.2 Play or Pause 1) Touch the Play/Pause icon on the ipod player screen to begin playing the selected file. 2) Touch the Play/Pause icon on the ipod player screen to pause the playing file. 7.3 File Previous & Review 1) Tap the Back icon on the ipod player screen to select the previous file. 2) Tap and hold the Back icon on the ipod player screen to review the audio contents of the currently playing file. Releasing the icon will allow playback to resume. 7.4 File Next & Cue 1) Tap the Forward icon on the ipod player screen to select the next file. 2) Tap and hold the Forward icon on the ipod player screen to cue the audio contents of the currently playing file. Releasing the icon will allow playback to resume. 7.5 Song Searching A quick file or song browser is available to view the available files in the current category 1) Turn the TUNE button to search the file title. 2) When the desired file title is displayed, press the TUNE button to begin playback of that file. 7.6 Repeat Play 1) During ipod play, tap the Repeat icon shown on the ipod player screen for less than 1 second. The Repeat icon will show a small 1 indicating that the currently playing file will play repeatedly. Playback of the same file will continue to repeat until the icon is tapped again. 2) Touch and hold the Repeat icon for more than 1 second. The icon will not show a small F indicating that playback of the currently selected folder will repeat. 7.7 Random Play 1) During ipod play, touch the Random icon for less than 1 second to play files on the ipod in a random or shuffled order. 2) Touch and hold the Random icon for more than 1 second. The icon will not show a small F indicating that playback of the files in the currently selected folder will play in random order. 23

26 ipod Player 7.8 Searching Files List (through Category search) 1) Touch the LIST button on the ipod player screen to display the stored files list. 2) Touch the desired file to play the file. Note: Using File browser screen. a. In ipod mode, touch the LIST icon to display the list of categories within the ipod memory. b. Select the desired category to display sub-categories. If there are no sub-categories, then the stored category list will be displayed. c. Repeat Step - b until reaching the stored category list. d. To move to a previous category, touch the name of the current category displayed at the top of the screen. For example, touching the Play lists within the above track will restore the previous category. e. Select the desired track from the list to play the category. f. Touch the icon to restore the previous screen. 24

27 AUX Input 8. AUX Input 8.1 Aux Connector 1) It is possible to connect your portable media player to the HYUNDAI D-Audio for playback of the audio tracks via the car speakers. 2) To get the best results when connecting the portable media to the HYUNDAI D-Audio, follow these steps: Use the supplied 3.5mm stereo plug to 3.5mm stereo plug cable to connect the media player headphone socket to the AUX socket located inside the centre console. Adjust the portable media player to approximately 3/4 (75%) volume level and start playback. Press the MEDIA button on the HYUNDAI D-Audio or press the steering wheel remote MODE button until the display shows Connected. Note: 1) The audio quality of your media player and the audio tracks on it may not be of the same sound quality as the HYUNDAI D-Audio's USB player. 2) If the volume level of the media player is too low compared with the radio or USB, increase the volume of the connected media player. 3) If the sound of the media player is too loud and or distorted, decrease the volume of the player. 4) For technical information regarding the AUX input, refer to the speci-fication section at the end of this manual. AUX socket located lower on the center console, inside cover. 8.2 Aux Player Screen Display Description Home icon Change the screen to media menu or main menu (home) selection. AUX / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the Aux screen. Display aux playing screen. 25

28 26

29 My Music 9. My Music Player 9.1 My Music Player Screen 9.2 Play or Pause 9.3 Track Previous & Review 9.4 Track Next & Cue 9.5 Track Scan 9.6 Song Searching 9.7 Searching Files List 9.8 Deleting File 9.9 Copying Files 9.10 Repeat Play 9.11 Random Play 9.12 Time Seek

30 My Music 9. My Music Player 9.1 My Music Player Screen Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. MyMusic / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) FILE Informations Displays current file information (Title, Artist, Album Name) RPT / RDM / Intro / Track No icon Executes play mode as repeat (all/one)/ random (on/off). Plays for 10 seconds for each next track. Diplays currently playing / total track number. Playing / Total time Diplays currently playing / total time. Previous / Next icon Plays previous / next track. Play / Pause icon Plays or Pauses currently playing track. LIST button Displays file list within the My Music. Copy button: Changes the screen to copy confirmation. (Copies the currently playing file from internal device to external device.) The My Music screen can be selected by pressing the MEDIA button, then tapping the My Music icon on the media menu screen. The My Music screen can also be selected using the MODE button on the steering wheel remote control. Note: The My Music icons on the media menu screen will be greyed out if internal memory are empty(no file). 28

31 My Music 9.2 Play or Pause 1) Touch the Play/Pause icon on the My Music player screen to begin playing the selected file. 2) Touch the Play/Pause icon on the My Music player screen to pause the playing file. 9.3 File Previous & Review 1) Tap the Back icon on the My Music player screen to select the previous file. 2) Tap and hold the Back icon on the My Music player screen to review the audio contents of the currently playing file. Releasing the icon will allow playback to resume. 9.4 File Next & Cue 1) Tap the Forward icon on the My music player screen to select the next file. 2) Tap and hold the Forward icon on the My music player screen to cue the audio contents of the currently playing file. Releasing the icon will allow playback to resume. Note: The Next and Previous functions can be operated by the steering wheel remote controls. Refer to the steering wheel control section for instructions. 9.5 File Scan Tap the Headset icon on the My Music player screen to play the first 10 seconds of each file on the USB memory device. The Repeat icon will show a small A indicating All files are being playback scanned. When the desired file is found, tap the Headset icon or the Repeat icon to continue playing that file. 9.6 Song Searching A quick track or song browser is available to view the available files in the current category. 1) Turn the TUNE button to search the track title. 2) When the desired track title is displayed, press the TUNE button to begin playback of that track. 9.7 Searching Files List 1) Tap the LIST soft button on the My Music player screen to display the contents of the internal memory device. 2) Files are selected by tapping the file name displayed on the screen. Slide the sliding position bar on the far right of the list screen to move files up and down for view. Note: 1) Use the TUNE knob to quickly display all files on the internal memory device. 2) When the desired file is shown, press the TUNE knob momentarily to begin playback of that file. 3) The number of tracks on the internal memory device is shown on the My Music player screen. 29

32 My Music 9.8 Deleting File 1) When a file is playing, you can delete the current file by touch the Delete button on the My Music List screen. 2) As shown below, the file name is shown and you are asked whether you wish to delete the file. 3) Touch the NO button to cancel deleting, and return to the previous screen. Touch the YES button to delete the file. 9.9 Copying Files 1) Tap the COPY button on the My Music player screen to copy the currently playing file. 2) Once copying starts, the copy screen will be displayed. 3) Once copying is complete, the copy screen disappears. 4) The copied file is stored to the USB memory and can be played within USB music mode Repeat Play During My Music play, tap the Repeat icon shown on the My Music player screen for less than 1 second. The Repeat icon will show a small 1 indicating that the currently playing file will play repeatedly. Playback of the same file will continue to repeat until the icon is tapped again Random Play During USB music or MyMusic play, touch the Random icon for less than 1 second to play files on the USB in a random or shuffled order Time Seek 1) The progress of the currently playing files is displayed on screen as a thin orange line. Elapsed and total time is shown at each end of the progress line. 2) Tap anywhere on the progress line to change the play. 30

33 Bluetooth Voice Recognition 10. Bluetooth Wireless Technology 10.1 Bluetooth Indicators 10.2 Bluetooth Connection Pairing a Bluetooth Device Setting your Bluetooth Device Disconnecting a Bluetooth Device Selecting a Bluetooth Device Deleting a Paired Bluetooth Device Bluetooth Audio Player 11.1 BT Audio Player Screen 11.2 Play or Pause 11.3 File Previous / Next 11.4 Playing Music Bluetooth Call 12.1 Bluetooth KeyPad Screen 12.2 Bluetooth Call List Screen 12.3 Bluetooth Contact Screen 12.4 Bluetooth Calling... Screen 12.5 Bluetooth Incoming Screen Voice Recognition 13.1 Voice Recognition Screen

34 Bluetooth 10. Bluetooth Wireless Technology Your HYUNDAI D-Audio supports Bluetooth wireless technology. Bluetooth technology provides a wireless link between a Bluetooth mobile phone or Bluetooth music player and the HYUNDAI D-Audio. The HYUNDAI D-Audio features a hands-free system so that you may talk on the telephone without taking your eyes off the road or your hands off the wheel. A microphone built into the front of the HYUNDAI D-Audio receives your voice and the calling party can be heard through the car speakers. Additionally, a Bluetooth music player can be wirelessly connected to the HYUNDAI D-Audio and playback music tracks in high quality sound through the car speakers. Some Bluetooth mobile phones include a music player and can provide both hands-free calling and music playback. Please check the user manual of your Bluetooth mobile phone or music for details of the Bluetooth features supported and how they are operated when connected to a Bluetooth audio accessory such as this HYUNDAI D-Audio. Note: When Using the Bluetooth Feature a. When the vehicle ignition switch is in the ACC position, the HYUNDAI D-Audio is on Stand-by, ready to connect with your mobile phone even if the car radio is switched off. The car battery may therefore become drained if the ignition switch remains in the ACC position for an extended period of time. b. Bluetooth technology uses low power radio transmission to connect to your Bluetooth mobile phone or Bluetooth music player. As radio signal strength reduces over distance, the quality of sound performance during phone calls and music playback may become poor if the distance between the radio and device widens. It is recommended that the mobile phone or music player is kept inside the car cabin, and where possible, close to the car radio for best performance. c. As a Bluetooth wireless connection can extend to 10 meters, your Bluetooth device may automatically connect to the HYUNDAI D-Audio even if the device is not in the car. d. Please consider this, especially when pairing or connecting Bluetooth devices to the HYUNDAI D-Audio when other Bluetooth devices may be within wireless radio range of the HYUNDAI D-Audio. e. The HYUNDAI D-Audio uses the latest Digital Noise & Echo suppression system to provide the best sound clarity with little or no distortion, but in some conditions there may be some echo and noise experienced. It is recommended to keep the car windows closed during hands-free calls for best results. f. The HYUNDAI D-Audio uses the following Bluetooth profiles: GAVDP (Generic Audio/Video Distribution Profile) PBAP (Phone Book Access Profile) HFP (Hands Free Profile) HSP (Head Set Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) 32

35 Bluetooth 10.1 Bluetooth Indicators shown on the Radio display Bluetooth Indicator 1) The Bluetooth logo above is displayed steady on the radio screen when a Bluetooth device is connected. 2) If the indicator is not displayed, then no Bluetooth device is connected or the connection is not of satisfactory quality. 3) The indicator may occasionally flash, indicating the radio is searching for a previously paired mobile phone or music player. Battery Strength Indicator 1) This indicator shows the condition of the battery charge level of your connected mobile phone. 2) The battery indicator on the radio display incorporates a series of vertical black sections providing a guide to the battery charge level. 3) This indicator may not be 100% accurate nor show the identical level of the battery compared to the indicator on the mobile phone or music player. 4) If your device does not transmit battery condition level via Bluetooth or is not fully compatible with the HYUNDAI D-Audio s Bluetooth specification, the indicator is not displayed. Signal Level Indicator 1) This indicator shows the signal strength of the mobile phone network received by your mobile phone within your current location. 2) This indicator will not be displayed if only a Bluetooth music player (without a mobile phone) is connected to the car radio. 3) The signal level indicator operates in a similar way to the battery strength indicator above and it s operation limitations may therefore also be similar Bluetooth Connection Pairing a Bluetooth Mobile Phone or Music Player 1) A Bluetooth connection must first be established between your Bluetooth mobile phone or Bluetooth music player and the HYUNDAI D-Audio. The first step to connecting the Bluetooth radio and Bluetooth device is to introduce or air the HYUNDAI D-Audio and Bluetooth device together. 2) It is recommended that you have the instruction manual for your Bluetooth mobile phone or music player with you during the pairing process described below to assist your understanding of how to set your device to pair with the HYUNDAI D-Audio. Note: It is recommended that all other Bluetooth devices other than the device to be paired are switched off during the following steps : a) to g). Paring instructions a. Press the PHONE button to display Bluetooth screen. If a Bluetooth is not connected, then press the PHONE button to display the Device Manager screen. b. Press the Setting button to display the Bluetooth setting screen. c. Press 1. Device Manager to display the Device Manager screen. d. To pair a new device, press the + or EMPTY button on the screen. e. The radio will now allow itself to be discovered by other compatible Bluetooth devices and the display will show Pairing Active - Enter Code 0000 into Device. f. Now, set your Bluetooth device to search for and pair with the HYUNDAI D-Audio. A guide for setting your Bluetooth device to search and pair with the radio is provided in section Setting your Bluetooth device to pairing mode. g. If you wish to end the radio PAIRING mode, press the CANCEL button. h. If pairing is successful, then the phrases Connected and Handsfree - device name will be displayed on the screen. i. If the paired Bluetooth device supports Bluetooth Audio, then B/T audio - device name will also be displayed. j.your Bluetooth device is now ready for use with the HYUNDAI D-Audio. 33

36 Bluetooth Notes: When Pairing Bluetooth Devices a. The HYUNDAI D-Audio allows a maximum of 6 Bluetooth devices to be paired. Once paired, the device is retained in memory and pairing is not required again unless the device is deleted from the car radio. b. Only one Bluetooth mobile phone may be connected to the HYUNDAI D-Audio at one time for hands free telephone operation. c. If a Bluetooth music player is to be connected together with a mobile phone, refer to the notes in section Playing Music using Bluetooth Audio. d. Bluetooth connection between the HYUNDAI D-Audio and mobile phone is normally established using the Hands Free Profile (HFP). However, some mobile phones may only allow the connection to establish in Head Set Profile (HSP) and therefore some functions may not be available Setting your Bluetooth Device to Pairing Mode 1) Select the Set up or Connectivity menu of your Bluetooth phone or music player and find the menu dealing with Bluetooth connection. 2) Select the function on the device to begin searching for Bluetooth devices. 3) After the search is complete, HYUNDAI should appear on the screen of the device. 4) Select CONNECT or SELECT device HYUNDAI. 5) The mobile phone or music player should now prompt you top enter a PIN code. Enter 0000 into your Bluetooth device. 6) The mobile phone or music player should confirm that it has established a new paired connection with the HYUNDAI D-Audio. 7) The pairing process is now complete. Notes: When Pairing Your Bluetooth Devices a. As each mobile phone or music player brand and model has a different menu structure and process for adding a Bluetooth audio accessory such as the HYUNDAI D-Audio you should refer to the user manual of your Bluetooth device for the accurate and correct procedure. b. A device must first be paired to the HYUNDAI D-Audio before it can be connected, i.e. if a device has been paired, it must then be connected before the hands free and/or audio playback features can be used. c. Once the Bluetooth pairing is complete, the HYUNDAI D-Audio will attempt to connect to your device. Some devices will require further operation to then connect to the car radio. It is recommended that the device is set to Automatically Connect to the HYUNDAI D-Audio so that whenever the car ignition switch is switched on, the device will automatically connect to the HYUNDAI D-Audio. d. The HYUNDAI D-Audio will give connection priority to the last connected mobile phone. e. t is recommended that all other Bluetooth devices other than that device to be paired are switched off during the pairing process. f. The 0000 passcode may not be required to be required on Bluetooth devices during the pairing process. g. The 0000 passcode is fixed in the HYUNDAI D-Audio and cannot be changed by the user Disconnecting a Bluetooth Device If disconnection of the Bluetooth mobile phone or music player with the HYUNDAI D-Audio is required, follow the steps below: 1) Select the Device Manager screen. 2) Press Bluetooth Device name to disconnect the currently connected mobile phone or music player from the HYUNDAI D-Audio. 3) Once the device is connected, then the phrases Disconnected and Handsfree - device name will be displayed on the screen. If the paired Bluetooth device supports Bluetooth Audio, then B/T audio - device name will also be displayed. 34

37 Bluetooth Selecting a Bluetooth Device The HYUNDAI D-Audio can pair up to 6 Bluetooth devices. A previously paired mobile phone or music player can be selected for connection using the method described below. 1) Select the Device Manager screen. 2) Select the Bluetooth device you want to connect. 3) If pairing is successful, then the phrases Connected and Handsfree - device name will be displayed on the screen. If the paired Bluetooth device supports Bluetooth Audio, then B/T audio - device name will also be displayed. Notes: When Pairing Your Bluetooth Devices a. The name of the Bluetooth device is sent by the device and stored in the HYUNDAI D-Audio memory. In most Bluetooth devices, the name can be changed by the user. Refer to the user manual of your Bluetooth device for details. b. If the selected previously paired Bluetooth device is switched off or if the Bluetooth feature is switched off, then the HYUNDAI D-Audio will retune to the previous screen when connection is attempted Deleting a Paired Bluetooth Device If a previously paired Bluetooth device is no longer to be used with the HYUNDAI D-Audio, it may be deleted from memory. 1) Select the Device Manager screen. 2) Press the - button in front of the Bluetooth device you want to delete. 3) After moving to the Delete Phone screen, then Handsfree - device name is displayed. If the paired Bluetooth device supports Bluetooth Audio, then B/T audio - device name will also be displayed. 4) Press the NO button if you do not wish to delete the device and pressing YES button to delete the selected device. 5) Once the Bluetooth device is successfully deleted, then the phrases Deleted and Handsfree - device name will be displayed on the screen. If the paired Bluetooth device supports Bluetooth Audio, then B/T audio - device name will also be displayed. 35

38 Bluetooth-Audio 11. BT Audio Player 11.1 BT Audio Player Screen Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. BT Audio / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows FILE Informations. Displays current file information (Title, Artist, Album Name) Previous / Next icon Plays previous / next track. Play / Pause icon Plays or Pauses currently playing track. The BT audio player screen can be selected by pressing the MEDIA button, then tapping the BT audio icon on the media menu screen. The BT audio player screen can also be selected using the MODE button on the steering wheel remote control. Note: a. A compatible BT device must be connected to head unit in order for the BT audio player to be activated. b. The BT Audio icons on the media menu screen will be greyed out if no BT device or playable files are available. 36

39 Bluetooth-Audio 11.2 Play / Pause 1) Touch the Play icon on the BT audio player screen to begin playing the selected file. 2) Touch the Pause icon on the BT audio player screen to pause the playing file File Previous / Next 1) Tap the Back icon on the BT audio player screen to select the previous file. 2) Tap the Forward icon on the BT audio player screen to select the next file Playing Music The HYUNDAI D-Audio supports the Bluetooth profile Advanced Audio Distribution Profile (A2DP). If your mobile phone or music player supports this profile then it is possible to listen to music tracks located on your Bluetooth device through the HYUNDAI D-Audio and car speakers. Additionally, the HYUNDAI D-Audio supports the Audio Video Remote Control Profile (AVRCP). If your Bluetooth mobile phone or music player supports this profile then it is possible to advance to the next track or replay previous tracks on using the buttons on the front of the HYUNDAI D-Audio or steering wheel remote controls (if fitted) on your vehicle. 1) Press the MEDIA button to select BT Audio mode. 2) Select the music player of your Bluetooth device. 3) Touch the PLAY on the device to begin playback (see notes below). 4) Touch the Back or Forward icon to advance to the previous or next music track. Using Steering Wheel Remote Control. 1) Press the MODE button until Bluetooth Audio is displayed. 2) Select the music player of your Bluetooth device. 3) Press PLAY on the device to begin playback (see notes below). 4) Press SEEK and buttons on the steering wheel to advance to the next or previous music track. Note: When Playing Bluetooth Audio a. Check your Bluetooth device user manual for details of how to play music tracks via an external Bluetooth audio system such as the HYUNDAI D-Audio. b. Some Bluetooth mobile phones cannot play music at all or may play music tracks in low quality audio through the HYUNDAI D-Audio. c. Text Information attached to music tracks on the music player (e.g. the elapsed playing time, song or artist name etc.) will not be displayed on the HYUNDAI D-Audio. d. Playback may automatically begin as soon as the Bluetooth Audio mode is selected using the radio or steering wheel buttons. When a device capable of playing music by Bluetooth audio and by USB connection is connected to the radio using the USB connector (eg. ipod Touch or iphone Models), it may be necessary to manually select the audio playback route on the device when changing modes on the HYUNDAI D-Audio. 37

40 Bluetooth-Call 12. BT Call 12.1 Bluetooth KeyPad Screen Display or Button Description Home icon Change the screen to media menu or main menu (home) selection. Bluetooth / Time Displays the operating mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Selecting menu button Selected the Bluetooth keypad screen. Shows the Play screen. Number, Keypad: Display Bluetooth KeyPad screen. Back icon Changes the screen to the currently playing media mode. Using the Bluetooth KeyPad screen. Touch the KeyPad button on the Bluetooth screen. Touch the desired phone number by keypad on the Bluetooth KeyPad screen. Touch the Call icon to calling the input number. Select phone key to change the keypad screen and input phone number for outgoing call and push Call icon. The Bluetooth screen can be selected by pressing the phone button, then tapping the keypad icon on the Bluetooth screen. The Bluetooth screen can also be selected using the MODE button on the steering wheel remote control. Note: a. A compatible BT device must be connected to the head unit in order for the Bluetooth function to be activated. b. The Bluetooth icons on the media selection screen will be greyed-out if not connected Bluetooth device. c. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 38

41 Bluetooth-Call 12.2 Bluetooth Call List Screen Display or Button Description Home icon Change the screen to main menu (home) selection. Bluetooth / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Selecting menu button Selected the call list screen. Shows the Play screen. BT Call list: Displays the contacts info as category like (outgoing, incoming, missed) Call Log List: Displays the contacts list for each category. Back icon Changes the screen to the currently playing media mode. Using the Bluetooth keypad screen. Touch the CallList button on the Bluetooth screen. Touch the desired phone number on each of call lists (outgoing, incoming, missed). Select the desired name in the list and then touch the phone number of mobile, home or office for outgoing call. How to select the Bluetooth screen. On the HYUNDAI D-Audio: If the Bluetooth device is connected. Press the PHONE button then, displays phone setting device or phone keypad screen when HYUNDAI D-Audio is offed or another mode is operating. Press the MEDIA button to display the media menu screen. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 39

42 Bluetooth-Call 12.3 Bluetooth Contact screen Display or Button Description Home icon Change the screen to main menu (home) selection. Bluetooth / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Selecting menu button Selected the Contact screen. Shows the Play screen. BT Call list: Displays the contacts info as category like (All, A to F, G to L,...). Contacts list: Displays the contacts list for each category. Shows the Play screen. Name, Number: Executes calling as category like (name, mobile, home, office). Back icon Changes the screen to the currently playing media mode. Using the Bluetooth Contact screen. Touch the Contact button on the Bluetooth screen. Touch the desired contact number on each of initial name. Phone book list can be downloaded automatically when BT pairing done via PBAP. It is possible to download 1,000 list for each phone device and see phonebook list at the contact mode in phone mode. How to select the Bluetooth screen. On the HYUNDAI D-Audio: If the Bluetooth device is connected. Press the PHONE button then, displays phone setting device or phone keypad screen when HYUNDAI D-Audio is offed or another mode is operating. Press the MEDIA button to display the media menu screen. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 40

43 Bluetooth-Call 12.4 Bluetooth Calling... Screen Display or Button Description Home icon Change the screen to main menu (home) selection. Call / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Selecting menu Contacts: Changes the screen to phone book displaying mode. Volume: Changes the mic mute to on or off. Keypad: Displays keypad during call state. Shows the Play screen. Calling... Displays the calling info as category like (name, phone number). Private / Hands Free button Changes the call mode to private or hands free mode. Call END icon: End call. Shows the Play screen. Number, #, *, screen: Inputs the ARS numbering. Using the Bluetooth Contact screen. Touch the Contact button on the Bluetooth screen. Touch the desired contact number on each of initial name. Phone book list can be downloaded automatically when BT pairing done via PBAP. It is possible to download 1,000 list for each phone device and see phonebook list at the contact mode in phone mode. How to select the Bluetooth screen. On the HYUNDAI D-Audio: If the Bluetooth device is connected. Press the PHONE button then, displays phone setting device or phone keypad screen when HYUNDAI D-Audio is offed or another mode is operating. Press the MEDIA button to display the media menu screen. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 41

44 Bluetooth-Call 12.5 Bluetooth Incoming screen Display or Button Description Home icon Change the screen to main menu (home) selection. Call / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the Play screen. Incoming Displays the incoming info as category like (name, phone number). Accept / Decline button Accepts the incoming call or decline it. Using the Bluetooth Incoming screen. At the incoming call, Caller ID is displayed. It is possible to get into handsfree mode and to communicate thought vehicle s microphone and speakers when touching Accept button. When touch Decline button, the calling complete and audio headunit operates in the last mode. How to select the Bluetooth screen. On the HYUNDAI D-Audio: If the Bluetooth device is connected. Press the PHONE button then, displays phone setting device or phone keypad screen when HYUNDAI D-Audio is offed or another mode is operating. Press the MEDIA button to display the media menu screen. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 42

45 Voice Recognition 13. Voice Recognition 13.1 Voice Recognition Screen Display or Button Description Home icon Change the screen to main menu (home) selection. Voice Recognition / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the Voice Recognition playing screen. BT AUDIO button Changes the media mode to BT Audio mode. How to select the Bluetooth screen. On the HYUNDAI D-Audio: If the Bluetooth device is connected. Press the VOICE button then, holding changes the screen to Voice recognition GUI and be ready to listen. And operates Siri / Voice recognition mode for phone. Press the MEDIA button to display the media menu screen. On the playing mode screen: Touch the Home icon at the top left hand corner of the display to change the main menu (home) selection screen. Touch the Bluetooth icon at the main menu (home) selection screen to display the Bluetooth screen. 43

46 44

47 Setting 14. Set up 14.1 Set up Screen 14.2 Set up screen - Sound Sound (Fader / Balance) Sound-BMT (Bass / Middle / Treble) Sound-EQ (Status value) Sound-BT (Ring / Voice volume) Sound-ETC (Beep / Loudness / Initial volume) 14.3 Set up screen - Display Brightness (Brightness / Colors / Contrast / Saturation) Display type (BT Display / Clock type) 14.4 Set up screen - Bluetooth Bluetooth Connection (BT Device) Bluetooth Connection Priority Bluetooth Info (Device name / Password) 14.5 Set up screen - System System Time (Current time / AM,PM / H-Type) Version (Model name / System,MCU,BT / Memory / Format)

48 Setting 14. Set up 14.1 Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Setup / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the Setup screen. Setup menu icon Displays the set up menu as category like (sound, display, Bluetooth, time, system). Sound setup icon Changes the screen to sound setting. Display setup icon Changes the screen to display setting. Bluetooth setup icon Changes the screen to Bluetooth setting. Time setup icon Changes the screen to currently time setting. System setup icon Changes the screen to system informations. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 46

49 Setting 14.2 Set up screen - Sound Sound (Fader / Balance) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Sound / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. Fader / Balance Displays the set up menu as category like (fader / balance value). Fader value set up icon (up/down) Changes fader setting value. Balance value set up icon (left/right) Changes balance setting value. Flat value set up icon Sets fader and balance value to default value. Shows the play screen. FAD: Displays fader value step as (10F,...F=R,... 10R). BAL: Displays balance value as (10L,... L=R,... 10R). Back icon Changes the screen to the currently playing media mode. Using the Sound set up screen. Touch the Sound icon at the set up screen to change the Sound set up screen. Touch the FAD / BAL button on the sound set up screen. Touch the up / down icon to select the level for fader volume. Touch the left / right icon to select the level for Balance volume. Controling fader / balance level, to change the volume red line and numbers on the screen. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 47

50 Setting Sound-BMT (Bass / Middle / Treble) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Sound / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. BMT: Displays the set up menu as category like (bass, mid, treble). Setting BMT (Tone) value button Changes the setting value each of tone (bass, mid, treble). Setting BMT (Tone) Flat value button Sets bass, middle, treble value to default value (0). Back icon Changes the screen to the currently playing media mode. Using the Sound set up screen. Touch the Sound icon at the set up screen to change the Sound set up screen. Touch the BMT button on the sound set up screen. Touch the up / down icon to select the level for each of TONE-Bass / Mid / Treble volume. Controling TONE-Bass/Mid/Treble level, to change the level red line and numbers on the screen. In case of changing Bass / Middle / Treble, EQ set-up level is memorized to user set. Touch the flat button on the display to setting all TONE-Bass/Mid/Treble volume that is Flat (0). How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 48

51 Setting Sound-EQ (Status value) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Sound / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. EQ: Displays the set up menu as category like (normal, classic, jazz, pop, rock) and User set. Setting EQ status buttons Changes the each of EQ status setting value (normal, classic, jazz, pop, rock). USER SET button Changes the screen to BMT(Bass, Mid., Treb.) mode. Back icon Changes the screen to the currently playing media mode. Using the Sound set up screen. Touch the Sound icon at the set up screen to change the Sound set up screen. Touch the EQ button on the sound set up screen. Touch the EQ status Normal / Classic / Jazz / Pop / Rock button to select the EQ status level automatically. Sound can be set up such as fader, balace, bass middle treble when user select user set at Equalizer. In case of selection of user set, EQ turns off and it gets back to the last set condition of BMT(Bass / Mid/ Treb). Possible to change and set the level by TUNE dial. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 49

52 Setting Sound-BT (Ring / Voice volume) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Sound / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. BT: Displays the set up menu as category like (ring, voice). Setting BT buttons Ring: Controls the ring volume level. Voice: Controls the voice volume level. Back icon Changes the screen to the currently playing media mode. Using the Sound set up screen. Touch the Sound icon at the set up screen to change the Sound set up screen. Touch the BT button on the Sound set up screen. Touch the plus / minus icon each of Bluetooth Ring / Voice to select the Bluetooth volume level. Possible to change voice and ring volume at calling condition. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 50

53 Setting Sound-ETC (Beep / Loudness / Initial volume) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Sound / Time Displays the mode & currently time. Currently playing state: Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume). Shows the set up screen. ETC: Displays the set up menu as category like (beep, loudness, initial volume). Setting ETC buttons Beep: Sets the beep out status as on, off and 2nd. Loud: Sets the loudness status as on or off. Initial Vol: Sets the initial volume level. Back icon Changes the screen to the currently playing media mode. Using the Sound set up screen. Touch the Sound icon at the set up screen to change the Sound set up screen. Touch the ETC button on the Sound set up screen. Touch the beep status OFF/2ND/ON button to select the beep status automatically. Touch the loudness function OFF/ON button to select the loudness function automatically. Rotate the volume knob or touch the plus / minus button to select the Initial volume. (If main volume is louder than initial volume after initial volume setting, volume gets back to initial volume at Audio On.) How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 51

54 Setting 14.3 Set up screen - Display Brightness (Brightness / Colors / Contrast / Saturation) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Display / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume). Shows the set up screen. Brightness: Displays the set up menu as category like (brightness / colors / contrast / saturation). Setting Brightness buttons Brightness: Sets the brightness level. Colors: Sets the color level. Contrast: Sets the contrast level. Saturation: Sets the saturation level. Back icon Changes the screen to the currently playing media mode. Using the Display set up screen. Touch the Display icon at the set up screen to change the Display set up screen. Touch the Brightness button on the Display set up screen. Touch the plus / minus button each of Brightness(Brightness,Color,Contrast,Saturation) to select the Brightness level. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 52

55 Setting Display type (Display / Clock type) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Display / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume). Shows the set up screen. Clock: Displays the set up menu as category like (displays, clock type). Setting Type buttons Display type: Sets the display type ( off or clock type). Clock type: Sets the clock type (digital or analog type). Back icon: Changes the screen to the currently playing media mode. Using the Display set up screen. Touch the Display icon at the set up screen to change the Display set up screen. Touch the Clock button on the Display set up screen. Touch the desired type icon each of Type (OFF, CLOCK / DIGITAL, ANALOG) to select the Display type. If select the CLOCK to display the selected Clock type screen when HYUNDAI D-Audio is offed. Digital Analog How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 53

56 Setting 14.4 Set up screen - Bluetooth Bluetooth Connection (BT Device) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Bluetooth / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume). Shows the set up screen. Connection Displays the set up menu as category like (BT device). Setting Bluetooth Connection buttons Connection Name Executes adding, connecting or disconnecting BT device. Touching + / - icon, then adding or deleting Bluetooth device. Back icon Changes the screen to the currently playing media mode. Using the Bluetooth set up screen. Touch the Bluetooth icon at the set up screen to change the Bluetooth set up screen. Touch the Connection button on the Bluetooth setup screen. Touch the desired Bluetooth device name to select the Bluetooth device connection. Touch the plus / minus icon to selects adding or deleting Bluetooth device. Refer to the below Bluetooth pairing scenario. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 54

57 Setting Bluetooth Connection Priority (BT Device) Set up screen Display or Button Description Home Change the screen to main menu (home) selection. Bluetooth / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume). Shows the set up screen. Priority Displays the set up menu as category like (BT device name). Setting Priority Device name buttons Device Name Sets the priority connection as selected phone device. Back icon Changes the screen to the currently playing media mode. Using the Bluetooth set up screen. Touch the Bluetooth icon at the set up screen to change the Bluetooth set up screen. Touch the Priority button on the Bluetooth set up screen. Touch the desired BT device name to select the Bluetooth device priority. Touch the device name icon to sets the priority connection as selected phone device. It gives priority to the connected Bluetooth device. If selected, the device is preferentially connected at the audio operation mode. If the highest priority is not searched, the last paired BT device at audio power off is connected. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 55

58 Setting Bluetooth Info (BT Device name / Password) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Bluetooth / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. Info. Displays the set up menu as category like (BT Infomation). Resetting button BT Reset: Initializes BT device connection infomation. (device name / password). Back icon Changes the screen to the currently playing media mode. Using the Bluetooth set up screen. Touch the Bluetooth icon at the set up screen to change the Bluetooth set up screen. Touch the Info button on the Bluetooth set up screen. Touch the desired Bluetooth device name to select the Bluetooth device priority. Touch the BT Reset button to sets the initial Bluetooth. Possible to check device name and pincode. Bluetooth mode shall be initialized at the reset condition and it s condition, all paired device shall be initialized. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 56

59 Setting 14.5 Set up screen - System System Time (Current time / AM,PM / Time type) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. Clock / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) Shows the set up screen. Time Text Display current setting time and AM/PM info. (current setting time and AM/PM info.) Setting Time buttons Hour/Min.: Changes time setting value. AM/PM: Changes AM/PM setting value. Clock Type: Changes the display type to 12hour or 24hour mode. OK button Saves the changed time setting information. Back icon Changes the screen to the currently playing media mode. Using the Time set up screen. Touch the Time icon at the set up screen to change the time set up screen. Clock in audio can be set to 12/24 hour mode. Touch the desired time type 12Hour or 24Hour button on the time set up screen. Touch the up / down icon each of hour/min. to sets the currently time. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 57

60 Setting Version (Model name / System,MCU,BT / Memory / Format) Set up screen Display or Button Description Home icon Change the screen to main menu (home) selection. System / Time Displays the mode & currently time. Currently playing state Displays the operating state. (EQ, BT, Phone Battery & Ant., Volume) System About button Model name: Displays model name. System, MCU, BT versions Displays system version, MCU version, BT version. System Memory button SD Used memory: Displays used internal memory. SD Remain memory: Displays remain internal memory. SD Format button Deletes all copied files & text. Back icon Changes the screen to the currently playing media mode. Using the Version set up screen. Touch the System icon at the set up screen to change the system setup screen. Touch the About button on the system setup screen. Check the model name, soft version(system, MCU, Bluetooth) on the display. Touch the Memory button on the system setup screen. Check the used memory,remain memory,format button on the display. By selection of memory tap, possible to check the memory status of emmc. How to select the Setup screen. On the HYUNDAI D-Audio: Press the SETUP button to display the set up screen when HYUNDAI D-Audio is offed or another mode is operating. On the playing mode screen: Touch the home icon at the top left hand corner of the display to change the main menu (home) selection screen. If the display to change the media menu screen, touch the home icon at the display. Touch the Setup icon at the main menu (home) selection screen to display the Setup screen. Touch the desired set up menu at the Setup screen. 58