A0316D. IBus Wall-Dock for Distributed Audio

Transcription

1 A06D IBus Wall-Dock for Distributed Audio M By

2 he A06 is an on-wall ipod docking station for distributed audio and supports IR functions. he dock connector slides in and out to adjust for any ipod and the non-skid pad helps to hold the music player in place. It s elegant and contemporary design make the A06 perfect for anyone who wants to enjoy their music without defacing their wall. Features:! Supports IR control: compatible with A0505 or Apple Remote! Built-in IR receiver! Charges the ipod! Mounts in a standard -gang box Front/op Wall Dock Hinged Dock Lid Rotates down to cover the dock connector Dock Connector Connects to ipod Non-Skid Pad Secures the ipod Front/Bottom Sliding Dock Platform Slides up to conceal the dock connector Slide p Sliding Dock Lever Slides the dock connector forward, providing easy access to dock your ipod Input RJ-5 & 0 Connectors Connect to CA5 Audio Hub CA5 cable (only use one) Output RJ-5 & 0 Connectors Connect to CA5 Audio Amplifier Input CA5 cable (only use one)

3 Front Audio Outputs Connect to your amplifier. IR Input Connect an IR receiver and use the A0505 remote to control your ipod. Output Wall Plate Back Installing the rim Plate Accessory RJ-5 & 0 Connectors Receive signals from the wall dock via Category 5 or Category 6 cable. Install Output wall plate in j-box Snap trim into place Install rim plate chassis over output wall plate Snap front cover over chassis Snap side flange on to front cover Compatibility Made For:! ipod touch (nd generation)! IPod touch (st generation)! ipod classic! ipod video! ipod nano (5th generation)! ipod nano (th generation)! ipod nano (rd generation)! ipod nano (nd generation)! ipod nano (st generation)! ipod mini! ipod with dock connector

4 S O R C E VOL CHANNEL VISION MODEL A0505 S O ZONE CAMERA CAV ME MOD VOL R C E Basic Application A06 Wall Dock Front Rear CHANNEL VISION MODEL A0505 A0505 Remote Control he built-in IR receiver allows the A06 to be controlled directly by the A0505. ZONE CAMERA CAV MOD ME CA5 cable up to 50ft. Whole-House Audio System Rear Front Pwr. IR receiver (optional) A06 Output Wall Plate Note: An IR emitter output from a whole-house IR system can also be connected here. As shown on the following page. A0505 Remote

5 VOL MOD CAV ME ZONE CAMERA S O R C E MODEL A0505 CHANNEL VISION 5 Sample Wiring Diagram: When used with the A6 Power supply not shown Connect an IR emitter output into the IR in of the A06 output wall plate. DVD player IR-80 CD player 6 Control 5 Control Control Serial IR Emitters Link Input Voltage S O P E A P K E R S O O O Hi-Z 5 I 75 N P P P P 6 C R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO + R - - L + + R - - L + + R - - L + + R - - L + + R - - L + + R - - L + Warning: Channel Vision A6 o prevent fire or shock hazard do not expose this unit to rain or moisture. ested o Comply With FCC Standards CAION FSE RISK OF ELECRIC SHOCK FOR HOME OR OFFICE SE 6 5 DO NO OPEN.5AL/50V 5VAC S 0/5V 50/60 Hz MAX 5W ~ RG59 or RG6 A6 Rear Panel RG59 or RG6 V or Video Display he single-gang trim plate can be used to hold a single-gang keypad next to the ipod dock in a -gang junction box. See installation section for details. IR signals detected by the A07 keypad will be repeated back to the A6. his allows control of the input sources. CA5 CA5 5

6 Your A06 Wall Dock comes mostly assembled for safer travel. Disassemble to the point of removing the front cover and then install following the steps below. Installing the Wall Dock 7 Installation Steps. Connect all wiring.. Attach main chassis to j-box using the provided four 6- screws. 5. Keep the dock connector circuit board in position in the opening in the front cover. 6. Hang the front cover on the main chassis from the two top tabs. 5. Secure the front cover with the two small screws at the bottom. 6. Place the dock platform over the slide rail and push downward until the retention snaps are engaged Slide the side protectors into the slots on the main chassis. Slide Rail 6 Retention Snap Steps & complete Steps 5 & 6 complete Completed Installation 6

7 Installing the Wall Dock In some installations it may be desirable to mount a single gang control keypad next to the A06. o accomplish this, the single gang trim plate can be installed next to the A06 in a -gang junction box. Follow the steps below: Installation Steps. Connect all wiring. se the correct installation tools: J-0 tool, or 0 crimp tool.. Install keypad and single-gang trim plate in the far left position of the -gang junction box. (See details on page ). Leave off the right side flange and trim piece.. Install the ipod dock in the left side of the -gang j-box. It will overlap and snap into the single gang trim plate. (See page 5 for details) See attachment detail on previous page Completed Installation 7

8 Docking the ipod he dock platform can slide up to hide the dock connector when the system is not in use. Make sure the dock platform is in the down position so the dock connector is exposed (as shown here). he sliding dock lever beneath the dock adjusts the position of the dock connector to create a perfect fit for all compatible ipods (see page for a list of compatible ipods). 8

9 sing the A0505 Remote Control he buttons above the ibus label on the A0505 remote control will mimic the functions on the ipod wheel. CHANNEL VISION MODEL A0505 ZONE CAMERA S O R C E he volume, mute, power, and source buttons on the A0505 are designed to control Channel Vision s whole-house audio systems such as the A60 and P-0. CAV MOD VOL ME Please note that this remote will only function when your ipod is docked in the A06 wall dock. It can be pointed directly at the wall dock or at an IR receiver that is part of an external whole-house IR system. An IR-80 cable can be used to connect the emitter output of the whole-house IR system into the IR IN of the A06 output wall plate. See page 5 of this manual for an example. We realize that custom integrators way wish to design advanced control systems. o provide assistance we have published the hex codes for the IR commands (see below). (IR codes can be downloaded at: Hex codes for IR commands: ibus Play/Pause: D B 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 0CA ibus Skip <<: D B 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 0CA ibus Skip >>: D A 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 00F 0CC 9

10 Connection ips and roubleshooting ) Be sure you have connected the CA-5 cable correctly. Follow the IA-568A standard at both ends. Incorrect wiring can cause distorted sound or prevent the system from working at all! ) Be sure you have connected the speakers in phase. Follow the label on the product. Out of phase speakers can rob the system of its bass. Especially when driving dual-voice-coil speakers. ) rouble with IR control? a. Make sure you are using the correct remote control. he A06 will only respond to IR signals from the Apple Remote produced by Apple Computer or the A0505 produced by Channel Vision. Other rd party remote controls are not supported. b. Disconnect anything that is connected to the IR IN on the output wall plate. Point the A0505 remote at the Wall Dock and see if you can control the ipod. If this works, you need to troubleshoot your IR repeating system. c. roubleshooting an external IR system: Some IR receivers have a feedback LED that flashes whenever IR signals are received. If the IR receiver you are using has this feature, check to make sure the LED flashes whenever you press buttons on your remote control. i. If you don t see the feedback LED, try replacing the batteries in your remote control. ) he A06 is designed to charge the ipod (see compatibility notes on page). When the ipod is not playing music, the screen should indicate that the ipod is being charged. If this does not occur, make sure the power supply is connected to the output wall plate of the A06. 5) Observe wiring distance specifications. he maximum recommended wire length between the wall dock and output wall plate is 50 fee for audio & power. For meta data output limitations, please reference page 9. 6) If you are experiencing problems with your ipod that occur even when it is not docked in the A06, then please contact Apple customer service for support. 7) If you need additional help troubleshooting the A06 please contact Channel Vision technical support or check our website for more details: Stripping and Connecting CA-5 Wire CA-5 cable should be stripped with a proper stripping tool, such as Channel Vision s J-0 tool.. Place the CA-5 between the blade and the first notch of the J-0 tool. Cat5 Blade. Rotate the tool only once. Multiple turns will cause you to cut into the inner wires.. Inspect the inner wires for damage. If any wires are cut start over at step. IA-568A RJ-5 Modular Plug Check for damage 8 Side view: op view: Green/White - Left channel ground Green - Left channel Orange/White - Right channel ground Blue - Signal Blue/White - Status Orange - Right channel Brown/White - Ground Brown - vdc

11 Specifications: C) Audio Output Output Level: 0.9 Vrms (may vary with ipod model) HD + Noise: <0.%, 0Hz-0kHz Signal/Noise: >-96dB Frequency Response: 0Hz-0kHz +/- 0.dB Output Impedance: 600 Ohms Power Requirements: 0.500A (500mA) Power Supply: 800mA Wire type: -pair, P Category 5, 5e or 6 Recommended Max. Cable Length: 50ft. (Audio & Power only) Video Output: Vp-p (may vary with ipod model) Video ype: Composite RS- Protocol Standard: 8-bit data, No Parity, stop bit Baud Rate Serial Cable Specification: Straight through, pins,, & 5 Dimensions: Wall Dock (-gang):.88 W x 5. H x. D(front) Rear Depth:.56 Wall Dock & Keypad (-gang): 6.7 W x 5. H x. D(front) Rear Depth:.56 Output Plate (-gang):.5 W x 5. H x. D(front) Rear Depth:.95 Color: White Operating emperature: -0ºC to +50ºC Distance limitation on Meta Data output of A06 ipod Nano Single Cat5-5 Single Cat6-0 Double Cat5-00 IPhone Single Cat5-85 Single Cat6-85 Double Cat5-0 ipod Classic Single Cat5-80 Single Cat6-80 Double Cat5-0 *Specifications subject to change without notice. 9

12 Channel Vision echnology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the SA, for one year from the date of original purchase. his is a no hassle warranty with no mail in warranty card needed. his warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision echnology, or failures due to accident, misuse, abuse, or alteration of the equipment. his warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling (7) A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton. his warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision echnology, your dealer or any factory-authorized service center. Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale. Made for ipod means that an electronic accessory has been designed to connect specifically to ipod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. ipod is a trademark of Apple Inc., registered in the.s. and other countries. ested o Comply Model: A06 ipod Wall Dock for Distributed Audio With FCC Standards his device complies with part 5 of the FCC rules. Operation is subject to the following two conditions: () his device may not cause harmful interference, and () his device must accept any interference received, including interference that may cause undesired operation. w w w. c h a n n e l v i s i o n. c o m Fischer Avenue, Costa Mesa, California 966 SA (7)-6500 (800) (7)-650 fax techsupport@channelvision.com Rev A