Quick Reference Guide

Transcription

1 English for North America Quick eference Guide Accessories The following accessories are supplied with this product. PUSH emote control Batteries () (AAA, 0, UM-4) AM loop antenna Indoor FM antenna AUX input cover Preparing the remote control Take off the battery compartment cover. Insert the two supplied AAA batteries into the battery case, following the polarity markings. Snap the battery compartment cover back into place. Items necessary for connection Speakers Ex. Ex. Ex. Ex. Front speaker enter speaker Surround speaker Active subwoofer Use speakers with an impedance of at least 6Ω. If you are using a T T, we recommend that you use magnetically shielded speakers. Prepare at least two speakers (for front). The priority of the other speakers is as follows: Two surround speakers ne center speaker External components able ables for connecting external components (may differ depending on the devices you are connecting) Speaker cables (a quantity to match the number of speakers you are connecting) Audio pin cable (for subwoofer) T Playback device such as BD (Blu-ray Disc)/DD players - -

2 onnect and install as follows the first time you use this unit. See the following explanations for the connections for each number. T 4 This unit BD/DD player (recorder) Front speaker Front speaker Subwoofer Surround speaker enter speaker Surround speaker onnect the speakers onnect a T onnect playback device such as BD/DD players and recorders 4 onnect the A power cord, and turn the power on When connection and installation is finished, set up the speaker parameters

3 ANTENNA onnect the speakers Surround speaker Front speaker aution: SUBWFE FM GND AM SPEAKES SUUND ENTE FNT emove the A power cord of this unit from the power outlet before connecting the speakers. Generally speaker cables consist of two parallel insulated cables. ne of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the + (positive, red) terminal on this unit and the speakers, and the other cable into the - (minus, black) terminal. Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, HEK SP WIES! will appear on the front panel display when this unit is switched on. When connecting 6Ω speakers, set the speaker impedance to 6Ω on this unit before making connections. efer to wner s Manual for information on settings. Subwoofer onnecting front speakers enter speaker onnecting center speakers / surround speakers 4 KES FNT 4 emove approximately 0mm of insulation from the ends of the speaker cables, and twist the bare wires of the cables together fi rmly so that they will not cause short circuits. oosen the speaker terminals. Insert the bare wire of the speaker cable into the gap on the side of the terminal. Tighten the terminal. SUUND ENTE SPEAKE Press the tab on the speaker terminal down. Insert the speaker cable end into the terminal. ift the tab to fix the speaker cable in place. onnecting the subwoofer onnect the subwoofer input jack to the SUBWFE jack on this unit with an audio pin cable. onnecting the banana plug (Except U.K., Europe, Asia and Korea models) Tighten the knob, and then insert the banana plug into the end of the terminal. Banana plug KES FNT Set the subwoofer volume as follows. olume: Set to approximately half volume (or slightly less than half). rossover frequency (if available): Set to maximum. UME SSE/ HIGH UT MIN MAX MIN MAX Subwoofer examples - -

4 (BD/DD) (D) ( T ) onnect a T ideo input to this unit is output to a T using output jacks of the same kind. When you have made connections using different types of video such as and component video, make the same connection with your T. When viewing, be sure to switch the input source on your T to match the playback device. Input utput input omponent video input ideo input If your T has multiple inputs, connect with the following priority (A to ). DK A (BD/DD) 4 A When using an compatible T. MNIT MNIT B When using a component video input-compatible T. PTIA AXIA AXIA PTIA (D) ( T ) A A A A A 4 A 5 AUDI When using a T compatible with video input only. istening to T audio To playback T audio on this unit, connect the T audio output to this unit. onnect the following input jacks, matching the audio output jacks on your T. When viewing your T, select the appropriate input source on this unit. PTIA Audio output DK MNIT A PTIA AXIA AXIA PTIA A A A A 4 A 5 H When using an compatible T that supports Audio eturn hannel functions and / or ontrol functions (Ex. Panasonic IEA ink), you can enjoy the T sound on this unit as follows: When using a T that supports the Audio eturn hannel functions and ontrol functions The audio / video output from the unit to the T and audio output from the T to the unit are possible using a single cable. The input source is switched automatically to match operations carried out on the T, and that makes T sound control easier to use. For the connections and settings, refer to Single cable input to T audio with Audio eturn hannel function in wner s Manual. Audio output from T ptical digital output oaxial digital output Analog output Audio eturn hannel (Described in the right column) Input jack on this unit A or A4 A or A A5,,, or -AUX When using a T that supports ontrol functions When ontrol functions are enabled on the unit, input source can be switched automatically to match operations carried out on the T. For the connections and settings, refer to Switching the input source on this unit automatically when listening to T audio in wner s Manual. onnecting to A4 allows you to playback T audio just by pressing the T under SENE key

5 onnect playback device such as BD/DD players and recorders If your playback device has multiple audio/video outputs, connect with the following priority (A to D) to enjoy a higher quality sounds and images. A When playback device is capable of output B When playback device is capable of component video output (with optical digital audio output) PTIA DK A (BD/DD) 4 When playback device is capable of component video output (with coaxial digital audio output) AXIA MNIT PTIA AXIA AXIA (D) PTIA ( T ) A MNIT A A A A 4 A 5 D When playback device is capable of video output (with analog audio output) only When playback, select the corresponding input source the jack is connected. onnecting to allows you to select the input just by pressing the BD/DD under SENE key. onnecting to A allows you to select the A input just by pressing the D under SENE key. If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from component video output jacks and audio from analog output jacks. efer to wner s Manual for details. 4 onnect the A power cord, and turn the power on Be sure to aim the remote control directly at the remote control sensor on this unit during operation. A power cord To the power outlet. 0 0 within 0 ft SUE TANSMIT SEEP DE SET EEIE Press 4 A 4 5 -AUX [ A ] [ B ] DK - 5 -

6 5 Set up speaker parameters When you finish connecting, adjust the status, size, and volume of each speaker so that the output is normal. TANSMIT DE SET SUE EEIE SEEP 4 A 4 5 -AUX [ A ] [ B ] DK TUNE FM AM ESET TUNING INF MEM ENHANE SU. DEDE MIE MUSI STEE STAIGHT EEIE A STEP : Display the setting menu Press EEIE A on the remote control to switch this unit on. Press SETUP on the remote control. heck that Speaker Setup appears and press ENTE. This completes step. SETUP Speaker Setup SP SET onfig. S S. S S SENE BD T D ADI DD SETUP PTIN ENTE UME ETUN DISPA TP PP-UP MUTE MENU MENU E ENT T INPUT T T H MUTE SETUP ursor ENTE ETUN STEP : Set the speaker status and size 4 5 The settings in step are not necessary with the following speaker confi guration: Front speaker: woofer diameter is 6 cm or larger enter/surround speakers: woofer diameter is 6 cm or smaller Subwoofer: connected heck that onfig appears and press ENTE. Use ursor B / to select the speaker (subwoofer) you want to configure, and then use ursor D / E to select speaker status and size. Information Description Setting Subwoofer Sets the subwoofer status. es/none Front enter Sur. Selects the size (sound reproduction capacity) of the front speakers. Selects the size of the center speakers. hoose None if you do not have a speaker connected. Selects the size of the surround speakers. hoose None if you do not have a speaker connected. Small/arge None/Small/arge None/Small/arge rossover Audio with a frequency below this limit will be output from the subwoofer or the front speakers. 40 Hz to 00 Hz F Phase Switchs the phase of the subwoofer. NM/E Extra Bass. NFIG Subwoofer;;es Selects whether to play front channel low-frequency components through either the front speakers or the subwoofer (ff), or through both the subwoofer and front speakers (n). n/ff S S Whether or not you set rossover, F Phase, and Extra Bass is optional. heck how the effects sound and then configure them to your liking. Use the following as a guide when setting speaker sizes. 6 When you have completed the settings for one speaker, repeat the same procedure for all speakers to complete settings. Press ETUN when setting is complete. This completes step. STEP : Set the distance from the listening point 7 Press ursor to display Distance and press ENTE.. DIST Unit;;;;;;feet S S ontinues to the next page - 6 -

7 8 Press ursor B / to select the speaker (subwoofer) that you want to configure, and press ursor D / E to set the distance. If necessary, you can change the setting units under Unit. Information Description Setting Unit Switches between setting units (feet / meters). feet (ft) / meters (m) Front Front speaker.0 ft to 80.0 ft (0.0 m to 4.0 m) Front Front speaker.0 ft to 80.0 ft (0.0 m to 4.0 m) enter enter speaker.0 ft to 80.0 ft (0.0 m to 4.0 m) Sur. Surround speaker.0 ft to 80.0 ft (0.0 m to 4.0 m) Sur. Surround speaker.0 ft to 80.0 ft (0.0 m to 4.0 m) F Subwoofer.0 ft to 80.0 ft (0.0 m to 4.0 m) 9 When you have completed the settings for one speaker, repeat the same procedure for all speakers to complete settings. Press ETUN when setting is complete. This completes step. STEP 4: Playback a test tone Press ursor repeatedly to display Test Tone and press ENTE. 0 Use ursor D / E to select n. A test tone plays back from the speakers as soon as you select n. The test tone plays back in a clockwise fashion. nly speakers confi gured for use in procedure 5 output the test tone. heck that the test tone is playing back and press ETUN. This completes step 4. TEST >ff n. S S STEP 5: Adjust the volume Press ursor B repeatedly to display evel and press ENTE. 4 5 Use ursor B / to switch the speaker that is outputting the test tone, looking for speakers with a different volume level to the others. The front panel display shows the speaker that is outputting the test tone. nly speakers configured for use in procedure 5 output the test tone. Information F F S S F EE F----d ---- If you fi nd a speaker with a different volume level to the others, use ursor D / E to adjust the volume. Use Front speaker or as a default when adjusting volumes. d Speakers Front speaker Front speaker enter speaker Surround speaker Surround speaker Subwoofer. S S To raise the volume: Press ursor E. To lower the volume: Press ursor D. epeat steps 4 and 5 to adjust the volume balance for all speakers to your preference. Press ETUN when setting is complete. eturn to the previous menu. This completes step 5. epeat procedures 0- (step 4) to stop playback of the test tone. nce you have completed all settings, press SETUP to close the Setup menu

8 INF MEM ESET FM AM TUNING PTABE peration guide UME SENE BD DD T D ADI PHNES INPUT TNE NT GAM STAIGHT AUX SIENT INEMA A Switches this unit between on and standby modes This unit switches between on and standby mode every time you press this key. B hoose an input source to listen to The name of the selected input source appears on the front panel display.. S S Select sound field programs and sound decoders Front panel GAM STAIGHT emote control MIE MUSI ENHANE STEE SU. DEDE STAIGHT Description Selects sound field programs optimized for viewing movies, dramas, and sports. Selects sound field programs optimized for appreciating music. Selects settings for stereo playback or enhancers for compressed audio. Selects surround decoders such as Dolby Pro ogic II. Switches to straight decoding mode for faithful reproduction of audio / video. SUE SETUP TANSMIT SEEP A SENE ENHANE STAIGHT PTIN EEIE AUX TUNE FM INF AM MEM ESET MIE MUSI STEE BD DD TUNING SU. DEDE T D ADI ENTE DE SET [ A ] [ B ] DK UME D Adjusts the volume level The current volume level is displayed on the front panel display. ETUN TP MENU DISPA PP-UP MENU MUTE. olume -8.5dB S S E E Mutes the sound The indicator blinks while the sound is muted. F Switches between input settings ou can switch input sources and sound field programs with a single key. SENE Input Sound field program BD/DD STAIGHT T A4 STAIGHT D A STAIGHT ADI TUNE 5ch Enhancer - Pressing and holding this key allows you to store input sources/sound field programs. - Press this key when this unit is in standby mode to switch on the unit ENT T INPUT T T H MUTE G Adjusting high/low-frequency sound (Tone control) Press TNE NT to select Treble or Bass. TNE Treble 0.0dB. Press GAM l / h to increase the setting. S - ou can set the tone control for speakers and headphones separately. onnect the headphones when adjusting the headphone tone control. - If you set an extreme tone balance, sounds may not match those from other channels. S 0 amaha orporation D8A0/QEN - 8 -