12/24/240V LED TV/DVD/PVR SMART TV (32") Instruction Manual

Transcription

1 12/24/240V LED TV/DVD/PVR SMART TV (32") Instruction Manual

2 What s in the Box TV Controls & Mounting TV Input & Output Contents SYSTEM CONNECTIONS AV Input 5 PC Input 5 HDMI Input 6 YPbPr (Component) Input 6 Output 7 USB Input 7 Remote Control 8 Remote Control Functions 9-11 First Time Operation 11 TV MENU OPERATION Source Selection 12 Using the TV Menu System 12 Picture Menu Sound Menu Applications Menu (TV Tuner) Electronic Program Guide 19 PVR 20 Preferences Setup Menu MEDIA PLAYBACK Photo Movie Music USB Drive Setup SMART TV OPERATION Info & Quick Start Guide 28 Launcher 29 My Recommend & My Apps 30 Local 32 Settings Menu Built-in DVD Player Operation Cleaning and Maintenance Troubleshooting Specifications

3 Important Safety Instructions (cont) AU TEL: NZ TEL: May Before installing this TV set, make sure your outlet voltage corresponds to the voltage stated on the appliance rating label of the power adaptor being used.. Only use this TV with the power adaptors supplied. If either plug does not fit into your outlets, consult your dealer or an RV service center for replacement of the outlet. Do not overload the power outlet. CAUTION the power supply cord, plug and antenna cable to rain or moisture; do not use it anywhere near water; do not touch the power plug with wet hands. Do not let the cord hang over the edge of a table or counter, or touch hot surfaces. Do not allow anything to rest on or roll over the power cord and antenna cable. Protect the cord and run all cables so that no one steps on or trips over them. Do not run the cord near heat-producing appliances such as radiators, stoves or irons. The excessive heat could melt the insulation and expose live wires. When not in use, disconnect the power cord from the outlet. Hold the plug, not the cord, when disconnecting the unit. Pulling the cord can damage the internal wires and may cause a fire. Never touch the TV screen, antenna or cord during thunderstorms. Stop use during thunderstorms; unplug the unit when a thunderstorm is approaching. Usage conditions and restrictions Follow the instructions in this manual when installing and adjusting the TV set. Only adjust those controls that are covered in this instruction manual; improper adjustment of other controls may result in damage. If this happens, unplug the TV and have it serviced by appropriately qualified personnel. Do not change or modify the TV set in any way. Only use the attachments/ accessories specified. Do not cover the ventilation openings with items such as newspapers, tablecloths, curtains etc., as this could impede ventilation. Do not insert any objects of any kind into this unit through the ventilation slots or DVD slot, as they could touch the current-carrying parts or short-circuit parts, resulting in fire, electric shock or damage to the unit. Do not touch the screen with fingers, as this may scratch or smudge the TV screen. Do not expose the batteries to excessive heat such as sunshine, fire or the like. Unplug the TV set in all of the following circumstances: If it has been subject to impact or has been dropped and is damaged. If its voltage adaptor plugs, or the wall socket, are damaged. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure they do not play with the TV. Position If a television is not positioned in a sufficiently stable location, when stand mounted, it can potentially be hazardous if it falls. Many injuries, particularly to children, can be avoided by taking simple precautions such as: Using cabinets, shelves or stands that provide a sturdy support for the TV and are not in areas where the TV can be accidently knocked or bumped. Only using furniture that can safely support the television. Ensuring the TV is not overhanging the edge of the supporting furniture. Not placing the TV on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the TV to a suitable support. Not standing the TV on cloth or other materials placed between the TV and supporting furniture. Educating children about the dangers of climbing up to reach the TV controls.

4 Important Safety Instructions (cont) When deciding where to put the TV set, make sure the location is: Well ventilated. Leave at least a 20cm space all around the TV set for good ventilation. Protected from overheating and away from direct sunlight. Away from damp and cold. Away from areas with extremes of temperature (below 0 C or exceeding 40 C) or moisture. Away from moisture drips or splashes. Protected from excessive dust. Do not install this equipment in a confined space such as a bookcase or similar. Do not put any objects filled with liquids, such as vases, on top of the TV set. Do not place any naked flame sources, such as lighted candles, on top of the TV. What s in the Box TV with inbuilt DVD Player Remote Control Manual Audio Out Adaptor BB4*12 4PCS BM4*10 4PCS 1 2

5 TV Controls TV Input & Output Rear Bottom PC HDMI 2 HDMI 1 Y Pb Pr VGA VOL+ VOL- CH+ CH- MENU SOURCE POWER Rear Side Controls on the TV VOL+ VOL- CH+ CH- MENU SOURCE POWER 1. After you insert a disc in the disc tray, press the button to play, and press twice to pause. 2. Press the button when the power is on to eject the disc. Press the button again to re-load the disc. 3. VOL(+) - This button increases the TV s volume. If the On Screen Display (OSD) menu is active, pressing this button will move the selection to the right. 4. VOL(-) - This button decreases the TV s volume. If the OSD menu is active, pressing this button will move the selection to the left. 5. CH(+) - This button changes the TV channel upward. If the OSD menu is active, this button functions as up control for the menu. 6. CH(-) - This button changes the TV channel down. If the OSD menu is active, this button functions as down control for the menu. 7. MENU - This button activates the OSD menu. If a sub-menu is active, pressing this button will return selection to the previous menu level. 8. SOURCE - This button switches between all the different sources of the TV. When the OSD is active, this button acts as the enter button and confirms the menu selection. 9. POWER - Turn on the TV by pressing the button once. Press the button again to turn off the TV. Installation Wall Mounting RF USB MEDIA VIDEO L R EARPHONE 1. HDMI 2 Input Jack: HDMI in. 2. HDMI 1 Input Jack: HDMI in. 3. Y/Pb/Pr Input Jacks: Component Video in. 4. PC Audio Input Jack: Connect to the Audio Out jack of a computer. 5. VGA Input Jack: Connect to the VGA output jack on a personal computer. 6. RF Input: Connect to external antenna to receive the ATV/DTV signal in ATV/DTV mode. 7. USB: USB Port for media playback when Media is the TV s selected source. 8. VIDEO Input Jacks: Composite Video & Audio in (A/V). 9. Headphone Jack: Headphone output jack. 10. RJ45: Connection for a Network Cable for Smart TV Internet access. 11. USB: 2 x Smart TV Ports available for USB media/files, mouse and keyboard connection. 12. output: Audio output for external devices such as Head Units. 13. POWER (DC12/24V) input RJ45 USBX DC 12V NOTE:. Four mounting screws are supplied with this TV for use with the TV Bracket If. using a standard VESA 100 x 100 RV TV bracket, will need a 200 x 100 bracket converter. such as the RV Media 100 x 100 to 200 x 100 adaptor bracket P/N:

6 System Connections System Connections NOTE: Please, make sure the inputs and outputs have good connections before connecting power. 1. AV PUT Audio/video input: Use the SOURCE button to select AV on the remote control. DC 12V 3. HDMI PUT HDMI input: Use the SOURCE button on the remote control to select HDMI Source eg. Blu-ray, DVD, Satellite, camcorder etc DC 12V EARPHONE HDMI 1 EARPHONE Video Cable (Not supplied) VIDEO L R RF VIDEO L R USB RJ45 USBX2 PC HDMI 2 HDMI 1 Y Pb Pr VGA 2. PC PUT PC input: Use the SOURCE button on the remote control to select PC. VGA PUT VGA PUT Y Pb Pr PC PUT RF USB VIDEO L R RF USB RJ45 EARPHONE USBX2 PC HDMI 2 HDMI 1 Y Pb Pr VGA DC 12V 4. YPbPr COMPONENT PUT Video component input: Use the SOURCE button on the remote control to select YPbPr. This input consists of both Video (Green/Blue/Red) and Audio (Red/White) RF USBX2 RJ45 EARPHONE VIDEO L R USB DC 12V USBX2 RJ45 PC HDMI 2 HDMI 1 Y Pb Pr VGA PC HDMI 2 HDMI 1 Y Pb Pr VGA 5 6

7 Systems Connections 5. PUT The rear panel jack on the TV makes it easy to connect the audio system to the sound. DC 12V Remote Control 1 Installing Batteries Open the battery compartment cover on the back side. Battery Cable (Not supplied) EARPHONE RJ45 USBX2 2 Insert two 1.5V AAA size batteries in correct polarity. Don t mix old or used batteries with new ones. Cover 2xsize AAA 1.5V To use the remote control, point it towards the remote sensor at the front of the television. The remote control has a range of up to approximately seven meters from the TV at an angle of up to 60 degrees. Use the 3.5mm to RCA cable provided or 3.5mm to RCA cable. VIDEO L R 3 Closed the cover. USB Battery Cover RF PC HDMI 2 HDMI 1 Y Pb Pr VGA 6. USB PUT A: 2 x USB ports for Smart TV which can be used for a mouse, keyboard, Firmware Updates and to load Apps etc. B: Single USB port for Media playback when Media is the selected TV source. DC 12V - Batteries should not be exposed to excessive heat such as direct sunlight, fire or the like. - If not being used for a period of time, please remove the batteries from the remote in case of leakage. - Do not mix old & new batteries together. Antenna connection USBX2 Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly. EARPHONE RJ45 USB memory VIDEO L R 75ohm coaxial cable Antenna cable RF A NOTE: If the antenna lead is under strain when connected to the antenna jack, please use the supplied Antenna right-angle adaptor. USB MEDIA B PC HDMI 2 HDMI 1 Y Pb Pr VGA 7 8

8 Remote Control Functions No. Button Description /25 22/ AUTO P.MODE DISPLAY S.MODE QT SOURCE / /28 23/ POWER Turns the TV off and on. 2 MUTE Press to mute the sound. Press again to restore sound Press 0 9 to select a TV channel directly. The channel will change a er 2 seconds. AUTO adjust resolu on in PC mode. 5 Return to the previously viewed program AUTO P.MODE S.MODE MENU EXIT Select the picture mode. Select the sound mode. Allows you to navigate the on screen menus (OSD). Exit from the menu or sub menu. Allows you to navigate the on screen menus and adjust the system se ngs to your preference. 14 OK Select the highlighted op on. 15 CH+/ Press these two bu ons to change channels up or down VOL+/ QT Press these two bu ons to increase/decrease the volume. Quick Tune start scanning for TV sta ons. 18 Press to change the audio language in DTV or DVD mode DISPLAY ASPECT Press to display the source and channel's info. Select NICAM mode. Only be available in TV programmers with NICAM audio transmission. The default mode is mono. Press this bu on to select the aspect ra o of the screen (4:3, 16:9 etc). 22 D.MENU Quick naviga on for setup se ngs / DVD: Video and DVD Menu bu on. 23 SETUP DVD system setup. Only available when DVD source is selected. 24 D.DISP Quick naviga on during setup se ngs / DVD: DVD informa on bu on R (DELETE) G (RENAME) Delete func on bu on for use in DTV se Rename func on bu on for use in DTV se ngs. ngs Y (MOVE) B (SKIP) Move func on bu on for use in DTV se Skip func on bu on for use in DTV se ngs. ngs. 29 FAV Selects favorite viewing channels. 30 Smart TV return to home screen. 31 SMART Selects the Smart TV Source directly. 32 Smart TV return to previous screen or previous web page/ open DTV Record menu SLEEP SOURCE I/II EPG SIZE Set the me for the TV to turn off automa cally. Press to select signal sources for the TV. Ejects the DVD. Press to display EPG (Electronic Program informa on) for TV. Smart TV Open Web Browser. Smart TV Open onscreen keyboard where text entry is required. Smart TV delete text. Teletext func on no longer used in Australia. 9 10

9 Remote Control Functions cont d No. Button Description 38 Play and Pause control for the Media Player and DVD REC/ Fast Rewind control for the Media Player and DVD. Fast Forward control for the Media Player and DVD. Press to record the current TV program to USB Stops playback of the Media Player and DVD. Plays previous Media Player file or previous DVD scene. Plays the next Media Player file or previous DVD scene. Source Selection Press the SOURCE button to display the input source list. Press / buttons on the remote to select the input source you want to watch, Then press the OK button to select the desired input source. First Time Operation - Quick Setup Using the TV Menu System When you turn on the TV for the first time or Reset the TV from the Setup menu, will be presented with a number of dialogue boxes that will step you through the TV tuning process. Setup Process Selection 1: Language - English - select OK on the remote Selection 2: Country - Australia - select OK on the remote Selection 3: DTV Type - Terrestrial - select OK on the remote Selection 4: Primary Subtitle Language/Secondary Subtitle Language - do not change as subtitles are no longer available in Australia. For Primary & Secondary Audio Languages, you can make changes to these by pressing the right arrow on the remote but note that additional Audio Languages are dependant on the TV broadcaster - eg SBS.. Press OK on the remote to complete selection. Selection 5: Tuning Mode - (ensure you have the TV Antenna connected). Press the right arrow on the remote to select DTV only as ATV (analogue) TV signals are not available in Australia any more - this will speed up the tuning process. Press the down arrow on the remote to scroll down to Start Scan and press OK to start tuning in the TV stations. After the Channel Scan is completed, the TV is ready use. Press the MENU button to display the MA OSD (On Screen Display) MENU; Press / buttons on the remote to select the MENU you want; Press the OK button or button to enter the sub menu, and press button to return back to the previous menu. Press / buttons to select an option and then press ENTER button or button to select the submenu, press / buttons to adjust the setting or press / buttons to select in the sub menu. Press the MENU button to save and return back to the previous menu, the press the EXIT button to exit the entire menu

10 Picture Menu Press the MENU button on the remote to display the main menu. Press / buttons to select Picture in the main menu, and then press the OK button to select. Picture Menu cont d Contrast Press / buttons to select Contrast, then press the OK button to select and press / buttons to adjust. Then press the MENU button to return back to the previous menu. Brightness Press / buttons to select Brightness, then press the OK button to select and press / buttons to adjust. Then press the MENU button to return back to the previous menu. Colour Press / buttons to select Colour, then press the OK button to select and press / buttons to adjust. Then press the MENU button to return back to the previous menu. Tint Press / buttons to select Tint, then press the OK button to select and press / buttons to adjust. Then press the MENU button to return back to the previous menu. Sharpness Press / buttons to select Sharpness, then press the OK button to select and press / buttons to adjust. Then press the MENU button to return back to the previous menu. 1.Press the / buttons to select the option that you want to adjust in the Picture menu, and then press OK button or button to select. 2.Press / buttons to adjust or press / button to select. Then press the OK button to select the sub menu. 3.After finishing your adjustment, press MENU button to save and return back to the previous menu, and press EXIT button to exit the entire menu. Picture Mode Press / buttons to select Picture Mode, then press OK button to enter and press / button to select. (Available Options: User, Dynamic, Standard, Mild) You only can change the of brightness, contrast, sharpness & color settings when the picture mode is set to User mode. TIP: You can press the P-MODE button on the remote control repeatedly to change the Picture Mode directly without having to enter the Picture Menu. Contrast Booster Press / buttons to select Contrast Booster, then press the OK button to select and press / buttons to select On or Off. Then press the MENU button to return back to the previous menu. Colour Temperature Press / buttons to select Colour Temperature, then press the OK button to slect and press / buttons to select between Standard, Cool and Warm. DNR - Dynamic Noise Reduction Press / buttons to select DNR, and then press the OK button to select and / buttons to select between Off, Low, Middle & High to enhance the picture if required. Reset Press / buttons to select Reset, then press the OK button to select the confirmation menu, and then choose OK to reset the Picture settings to default

11 Sound Menu Press the MENU button to select the main menu. Press / buttons to select Sound in the main menu, and then press the OK button or button to enter. Sound Menu cont d Balance Press / button to select Balance, then press OK button to enter and press / button to adjust. Then press MENU button to return back the previous menu directly Surround Press / button to select Surround Sound mode, and then press the OK button to select and press the / buttons to select ON or OFF. AVL Press / button to select AVL, and then press OK button to enter and press / buttons to select ON or OFF. Digital Audio Output Press / buttons to select Digital Audio Output, then press OK button to enter and press / button to select. (Available SPDIF mode: OFF, PCM, AUTO) Then press the OK button or button to select and press / button to adjust, then press the MENU button to return back the previous menu. 1.Press / buttons to select the option that you want to adjust in the Sound menu, then press the OK button to select 2.Press / buttons to adjust or press / to select, and press OK button to select the submenu. 3.After finishing your adjustment, Press the MENU button to save and return back to the previous menu, or press EXIT button to exit the entire menu. Sound mode Press / buttons to select Sound mode, and then press the OK button to select and then press / buttons to select. (Available Sound modes: User, Standard, Music & Movie). You can only change the value of Bass &Treble when the sound mode is set to user mode. Reset Press / buttons to select Reset, then press the OK button to select the confirmation menu, and then choose OK to reset the Sound settings to default. Applications Menu (TV Tuner) Press the MENU button on the remote to display the main menu. Press / buttons to select APPLICATIONS on the main menu, and then press the OK button to select. TIP: You can press the S-MODE button on the remote control to change the Sound Mode directly without having to select the Sound menu. Bass Press / buttons to select Bass, then press / buttons to adjust. Note Bass can only be adjusted in User mode. Then press the MENU button to return to the previous menu. Treble Press / buttons to select Treble, then press / buttons to adjust. Note Treble can only be adjusted in User mode Then press the MENU button to return to the previous menu. Press / buttons to select the option that you want to adjust in the APPLICATIONS menu, and then press OK button to enter. 2. Press / buttons to select and press OK button to select the sub menu. 3. After finishing your adjustment, press the MENU button to save and return back to the previous menu, or press EXIT button to exit the entire menu

12 TV Tuner Channel Menu Channel Press / buttons to select Channel, and then press the OK button to change to the channel selected. The menu will appear as follows: TV Tuner Menu cont d Key Description: CH button: Press CH+ or CH- for the next or previous page. RED button: Press this button to set favorite channels. GREEN button: Press this button to lock the channel. YELLOW button: Press this button to skip the channel, if the channel is already skipped, press the YELLOW button again to cancel skip. Country Press / buttons to select Country, and then press / buttons to select your country. DTV Type Press / buttons to select DTV Type, then press / button to select. Note the Default setting is Terrestrial and should not need to be changed. Auto Tuning Press / buttons to select Auto Tuning, and then press the OK button to select (When the System Lock is on, please input the P code to unlock). Select to open the auto search menu and then press the OK button to start the scan. ATV Manual Tuning Press / buttons to select ATV Manual Tuning, and then press the OK button to start the scan. Remote Functions: CH button: Press CH+ or CH- to change the page. RED button: Press this button to modify the channel number. GREEN button: Press this button to move down the channel (channel order). YELLOW button: Press this button to sort the channels. GREEN button: Press this button to delete the channel selected. 0-9 buttons: Press these buttons to jump to the appropriate channel by inputting different channel numbers. Channel Options Press / buttons to select Channel Options, and then press the OK button to select the channel List menu. The menu will appear as follows: DTV Manual Tuning Press / buttons to select DTV Manual Tuning, and then press the OK button to start the scan. Common Interface This function is not available on this TV. Prsgramme Timers Press / buttons to select Programme Timers (scheduled Viewing and Scheduled Recording), and then press OK button to select. Guide Press / buttons to select Guide (EPG), and then press OK button to select

13 Electronic Program Guide EPG The EPG (Electronic Program Guide), which is available on DTV, allows you to see what program is currently playing on the TV and to see upcoming programs on the current channel plus other channels. To view the EPG, press the EPG button on the remote (button 33). PVR (Personal Video Recorder) PVR Recording The PVR (Personal Video Recorder) allows you to record Digital TV Programmes. It requires a correctly formatted USB drive or portable hard drive* to be plugged in to the TV before you begin. To check if the USB or HD is compatible and formatted correctly, Select the Media Source on the TV then Select Setup. Use the down arrow on the remote to select the USB or HDD then press OK to format the device. NOTE ALL EXISTG DATA WILL BE ERASED ON THE DEVICE.. Use the up and down arrows to view program info and left/right arrows to Change the channel being displayed. Use the Green and Yellow buttons on the remote to change days. To change the Program (if you have selected a different Channel), press OK on the remote. The PVR function can be activated in 2 different ways. 1. To quickly record the current TV channel you can press the Record button on the Remote (Button 41). To stop recording, press the Record button again which will display the Record menu on the bottom of the screen. From there you can also select the square button to stop recording. 2. To schedule a PVR recording, first open the EPG and locate the programme you would like to record by using the up and down arrows. When the desired program is selected, press OK on the Remote. * As there are many types and brands of portable HDD s on the market, it cannot be guaranteed that every model will be compatible with this TV. NOTE If you select a program that is not currently being viewed, this will bring up the timer menu which will allow you to set a reminder for the TV to automatically change channels to your selected program. For this operation, in the Timer menu, View must be displayed. If this is changed to Record, the program will be set to Record - see next page. Channels can only be changed by the Timer when the TV is turned on. NOTE If TIMER FULL is displayed, this means that another program is set to view (or record) at the same time. t A menu like the above will then be displayed. To confirm and schedule recording of the programme, use the Remote to highlight the Set Timer option and select OK on the Remote. TIP Press the Blue button on the remote to view the Programme Timers menu (above right). This screen will show you which programs are scheduled for a reminder to view (View will be listed in the Operation column), and which Programs are scheduled to Record (Record will be listed in the Operation column). NOTE The TV MUST remain turned on to record shows using the timer (the TV will automatically change channel to record the program but it will not record the program if not turned on) LIVE PAUSE By pushing the Record button the remote then selecting Pause, you can pause live TV as long as the is a USB drive inserted in the TV with enough available storage. You then can select Play to continue viewing from where you paused the Program. NOTE. The paused Program will be lost if the channel changed

14 Preferences Menu Preference Menu / Setup Menu The picture is for a reference only; the actual item is the standard. Press MENU button to display the main menu. Press / buttons to select PREFERENCES in the main menu, and then press OK or to enter. Automatic Power Down Press / button to select Automatic Power Down and press / button to select ON or OFF. CEC Settings Press / button to select CEC Settings, and then press ENTER to enter the sub menu. Setup Menu Press the MENU button to display the main menu. Press / buttons to select Setup in the main menu, then press OK to enter. 1.Press / buttons to select the option that you want to adjust in the PREFERENCES menu, then press OK to select 2.Press / buttons to adjust or press / buttons to select. 3.After finishing your adjustment, press the MENU button to save and return back to the previous menu and press the EXIT button to exit the entire menu. Menu Language Press / buttons to select Menu Language, then press the OK or button to enter the sub menu, then press / button to select, then press the OK or button to confirm. Teletext Language *Not Available in Australia Key Lock Press / buttons to select Key Lock, then press the OK button to enter and press / button to select ON or OFF. PC Settings Press / buttons to select PC Settings, then press OK to enter the sub menu, Then Press to enter, then press OK or to confirm. (When the PC signal is connected). System Lock Settings Press / buttons to select System Lock Settings, and then press OK to enter the sub menu. The default P Code is (0000)

15 Setup Menu cont d 1.Press / buttons to select the option that you want to adjust in the Setup menu, then press the OK or button to select. 2.Press / buttons to adjust or press / buttons to select. 3.After finishing your adjustment, press the MENU button to save and return back to the previous menu and press EXIT button to exit the entire menu. OSD Timer Press / buttons to select OSD Timer, and then Press / buttons to select. (Available OSD Timer Options: 10 S, 20 S, 30S, 40S, 50S, 60S, off), then press OK to confirm. MEDIA Playback Note 1: Before selecting the MEDIA source, Plug in a USB device with relevant media content, then press the SOURCE button to set the TV s Source to Media. Note 2: The USB device must be formatted FAT or FAT32 to be compatible with this TV s Media playback function. Note 3: Media can also be played back via the TV s Smart TV mode. If a file will not play using the TV s MEDIA Playback function, please try it using the Smart TV media players. Press / buttons to select MEDIA in the Source Menu, and then press OK or to Select. You can also enter Media Playback by pressing MEDIA button on the remote control. Cinema - Screen Ratio Press / buttons to select Cinema, and then Press / buttons to select. (Available Cinema: Auto, 4:3, Wide 16:9, Super Live), then press OK to confirm. Blue Screen Press / buttons to select Blue Screen Off or On, when there is no input signalthen press / to select On or Off.Press OK to confirm. Sleep Timer Press / buttons to select Sleep Timer, and then Press / buttons to select. (Available Sleep Timer Options: 00:15, 00:30, 01:00, 01:30, 02:00, off), then press OK to confirm. Location Press / buttons to select Location, and then Press / buttons to select Home or Store, then press OK to confirm. Quick Setup Press / buttons to select Quick Setup, and then Press then press OK to enter the sub menu, enter the password if locked, and then you can quickly go through the main TV setup settings. Reset TV - Restore TV to Original Factory Settings Press / buttons to select Reset TV, and then press OK to select the sub menu, enter the password if locked, and then you can restore the factory settings. Please see P11 for more information on First Time Installation settings. Press / buttons on the remote then OK to select either Photo, Movie (Video), Music playback or Setup USB Selection After you select your playback mode, then click on folder C to select the USB drive. Remember the USB drive must be inserted in the single USB port of the back of the TV, not the double Smart TV USB Port when in the Media source

16 MEDIA Playback cont d Photo Press / or / to select the photos, press the OK or button to view. MEDIA Playback cont d Movie. cont d Press the OK button to select the C: folder to view the attached USB drive. Photos can be viewed with a slide show. To start the slide show, select an image using the arrow keys on the remote control then press the OK button the remote to start the slide show. Once the slide show starts, press the menu button on the remote to adjust the slide show. Setting available include the delay between photos, the addition of background music, slide show repeat etc. You can use the same controls to adjust the playback of Movie & Music files as well. Movie Press / buttons to select Movie in the main menu, then press the OK button to select Press EXIT button to return back to the previous menu. Press OK button or button to play a video file, Press the button or EXIT button to stop playing. Press the button to return to the previous page. Music Press / buttons to select Music in the main menu, and then press the OK button to select. Press the EXIT button to return back to the previous menu. Press / buttons to select the audio file you want to listen to and then press OK or or button to play. Press the button to return back to the previous menu

17 MEDIA Playback cont d Smart TV - General Information & Quick Start Internet Connection To use the Smart TV functions you must have access to a WiFi network or wired (LAN) network. The TV features an inbuilt WiFi receiver and this is the preferred option to connect the TV to the Internet. Mouse/Keyboard While most functions can be controlled with the supplied Remote Control in conjunction with the Smart TV s on screen virtual popup keyboard; an optional Mouse, Keyboard or combination of both (not supplied) will allow faster operation of the Smart TV. Note: When using the TV s remote to control the Smart TV and you need to activate the on screen keyboard if it does not come up automatically (eg to sign-in to a service), press the button on the remote. Apps Apps are available for download from the Google Play store. Note you need a Google Play account to download the apps. To search for and download apps, click on the Google Play icon in the My Apps sub menu.. Once audio playback starts, you can press the menu button on the remote to adjust the audio playback settings. Setting available include sound quality settings (SOUND), Repeat options, Sleep Timer and Play List selection. Setup Press / button to select Setup in the main menu, and then press the OK button to select. Press EXIT button to return back to the previous menu. Smart TV Speed While the Smart TV can run a variety of apps, it may slow down once a number of apps have been opened. If you experience this, please disconnect the power from the TV for 10 seconds then turn it back on with the remote. Help/Updates Please visit the Camec website, and search the RV Media 32" Smart TV for any info/updates should they become available. First Time Operation When you select the Smart TV Source for the first time, you will see the following screen: Setup formats the USB device for Media playback PLUS the TV s PVR functions. When you are ready to format the USB drive, select Format Start then Yes. NOTE: Formatting the USB device will erase all existing data on the USB device. Select Next by pressing OK on the remote. Then select Next again which selects English as the system Language. Then press OK on the remote to confirm 100% screen size. Next using the arrow keys on the remote, select either a WiFi or Ethernet Internet connection. An Ethernet connection will immediately provide an Internet connection. For WiFi, after you select it you will then be provided with a list of available WiFi networks. Using the arrow keys on the remote and OK button, select your preferred WiFi network then input the password using the arrow keys on the remote in conjunction with the on-screen keyboard then press Done when you are finished. Then select Connect Now and Finish and your Smart TV will now be connected to the Internet! 27 28

18 Smart TV Operation Launcher Smart TV Operation My Recommend (Media Player) Sub Menu app shortcuts Launcher main screen, press the up and down + OK buttons on the Remote to select the desired sub menu or app. Apps are either stored in the My Apps Sub Menu or the smaller shortcut icons at the bottom of the screen. To return to this screen at any time, press the home button on the remote. To return to the previous screen within a sub menu, or to go to the previous webpage when using the Web Browser, press the button on the remote. This Sub Menu includes a Network Media Player app. If you have DLNA network storage, you stream media using this app. My Apps Sub Menu To add apps to the shortcut icons, select the + icon with the remote then select the app you want to add from the Sub Menu as pictured below. The RV Media TV comes pre-installed with a number of apps including a web browser, Google Play store and file viewer. When you install a new app by downloading it from the Google Play store, it will be displayed in this sub-menu

19 Smart TV Operation Website Sub Menu. Smart TV Operation/Settings Local Sub Menu When you select this option, a number of bookmarked Websites are displayed. Simply navigate to the desired website using the arrow keys on the remote and press OK to open the selected website (picture not representative of Australian version). Music Sub Menu By default, the local file Photo Viewer (Gallery), MoviePlayer and File Browser apps are located in this sub folder. These apps can be used to playback local files stored on the Local Disc internal memory (although this is not encouraged to preserve the internal memory for app installation) - or from a USB drive plugged in to the TV - which is labelled as USB(A:). Settings Menu This menu includes the inbuilt Music Player app so you can play back music that is stored on a USB drive. You can also add other apps to this sub menu by downloading the app then selecting the + icon to add the app to this sub menu. NETWORK This screen configures your Internet connection. First select Wi-Fi or Ethernet (note a Network cable must be plugged in to select Ethernet). For a WiFi connection, click on the WiFi network you wish to connect to, input the network password then the Smart TV will be connected to WiFi

20 Smart TV Settings Smart TV Settings DISPLAY This sets the Smart TV window size. You should not need to change this from the default setting. OTHER This screen displays the Smart TV Model Number, Android Version, Build number & Kernel version. System Update allows you to back up and/or restore your data. More Settings displays the core Android TV settings and should only be adjusted by advanced users. Factory Reset restores the Smart TV to its original settings. This is useful if the Smart TV is slowing down or you have apps that are crashing. Note any additional apps you may have installed will be deleted if you perform a Factory Reset ADVANCED Remote control allows the system to be controlled with Smart Phone apps when turned on. Digital audio auto-detection and Digital audio output should be left Off & set to HDMI passthrough respectively. LOADG NEW FIRMWARE (OTHER - SYSTEM UPDATE) Should new Smart TV Firmware become available, please select the Other/System Update menu. Then insert a USB drive with the new Firmware loaded on it. Click Select (circled above) to locate the Firmware update file and click on it to select the new Firmware. Then select Update to install the new Firmware and click Update again to begin the Firmware installation

21 Built-in DVD Player Operation Built-in DVD Player Operation(Cont.) 35 36

22 Built-in DVD Player Operation(Cont.) Built-in DVD Player Operation(Cont.) ITIAL SETTG(DVD) - - General Setup Page - - TV Display Wide - - Preference Page - - TV Type Audio Subtitle NTSC Eng Eng OSD Lang Eng Disc Menu Eng Captions Off Parental Last Memory Off Password Default Go To Preference Page 1. TV DISPLAY: Set the ratio of output to the television signal options are: Normal/PS(4:3 Pan Scan), Nomal/PS (4:3 Letter Box), Wide (16:9). The default setting is wide. 2. OSD Lang: Set the OSD Language options. 3. CAPTION: Overlay the captions on some DVD titles, optional setting: ON/OFF. 4. LAST MEMORY: Save the last playback point on the DVD: options ON/OFF - - General Setup Page - - Downmix STR Go To Speaker Setup Page 1. LT/RT: Logic Surround stereo audio output. This matrix-based coding process enables stereo audio tracks to carry four channels(left, center, right and surround) of audio data. 2. Stereo: Analog stereo audio output. The player sends the subwoofer and speech signals to your front right and front left speakers. 1. TV Type: This product supports output of various system, including Multi, NTSC, PAL. PAL: Choose this settings if your DVD player is connected to a PAL TV. The default setting is PAL: NTSC: Choose this settings if your DVD player is connected to a NTSC TV. MULTI: Choose this settings if your DVD player is connected to a multisystem TV. 2. Audio: DVD built-in disc dubbing language selection options. 3. Subtitle: This player provides English etc, languages as the built-in subtitle language. When playing DVD, you may hide the subtitle or choose any of them as the present subtitle language. 4. Disc menu: DVD Disc language selection options. 5. PARENTAL[DVD only]: This is to disable the playing of specified DVDs which are unsuitable for children. Some DVDs are encoded with specific rating level. lf the rating level of the disc is higher than that preset in the settings, playback of the disc will be blocked. To play the Disc, select the PARENTAL option and the screen will display to the PASSWORD menu. The default password is PASSWORD[DVD only]: Use this selection to change the PASSWORD. 7. Default: This option will return the original settings of this player

23 Built-in DVD Player Operation(Cont.) Built-in DVD Player Operation(Cont.) Chapter Title All O? 39 40

24 Cleaning and Maintenance Troubleshooting WARNG! For your personal safety, be sure to disconnect the power adaptor before proceeding with any maintenance or cleaning. Cleaning the TV screen Do not touch the TV screen with sharp objects. Use a clean, soft cloth to wipe off any dust and fingerprints from the TV screen surface. Wipe in a straight motion from the center of the TV panel to the outside. Do not clean the screen with water or chemical cleaners, as this may damage the TV screen surface. Never use chemicals such as household cleaning sprays, antistatic sprays or fluids, benzene or thinner to clean the TV screen. Cleaning the main unit Dust the TV set by wiping the screen and cabinet with a soft, clean cloth. If necessary, wipe the outside of the unit with a clean, soft cloth, moistened with lukewarm water. Do not use benzene, thinner or alcohol as these chemicals will smudge the surface finish. Maintenance Do not dismantle this product by yourself, as this may cause damage. There are no user-serviceable parts contained in the TV set. If your TV set has been damaged, contact the after sales support line for advice or take it to a local service center for inspection or repair. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling of appliance. This product should not be adjusted or repaired by anyone except properly qualified personnel

25 Troubleshooting(Cont.) Specifications " (80cm) LED NOT ALL TV CHANNELS CAN BE TUNED This is caused by a weak TV Signal which can be due to many factors such as RV location (in relation to the TV Transmitter), incorrect antenna rotation, poor quality antenna or poor quality antenna leads (eg the lead between to TV an wall socket). Even being located in a valley or gully or behind a large hill will affect the TV signal quality. SMART TV Android TV v Further, if the TV Channels are tuned in a weak signal area where not all channels can be received, and the RV is then moved to a stronger TV reception area, the TV will still not pick all channels up as they may not have been tuned in or stored. In this situation the TV should be retuned. If you cannot tune in all of the TV channels, one option is to plug the TV into better antenna (eg a home antenna) by connecting the TV via its 240V plugpack and retuning the channels to ensure they are all picked up. This will ensure that all TV channels can be tuned in when a strong enough signal is available. 3 TV Tuning can be activated easily by pressing the QT button on the remote control. RJ45 Out 732x441x71mm 732x484x174mm 8.0 kg DC12V 6A

26 *As RV Media continually strives to improve its products, Specifications may be subject to change without notice. Warranty Please complete your warranty card included with this TV. This product is backed up with a 2-Year Warranty. Warranty Helpline: V