User Manual. Unimax HSPA+ Ethernet Modem Router with I/O Board

Transcription

1 + Unimax HSPA+ Ethernet Modem Router with I/O Board User Manual This manual is the sole and exclusive property of Maxon Australia. Not to be distributed or divulged without prior written agreement. Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 1 of 11

2 Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 2 of 11

3 FCC RF EXPOSURE COMPLIANCE In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this device complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. The use of this device in any other type of host configuration may not comply with FCC RF exposure requirements and should be avoided. During operation, a 20cm separation distance should be maintained between the antenna, whether extended or retracted, and the user s/bystander s body (excluding hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance. CAUTION Change or modification without the express consent of Maxon Electronics Australia Pty. Ltd. voids the user s authority to use the equipment. This equipment has been tested and found to comply with the limits pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference in radio and television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient or relocate the receiving radio or TV antenna Increase the separation distance between the equipment and the receiver Contact Maxon Electronics Australia Pty Ltd. Technical Support for assistance. Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 3 of 11

4 CONTACT INFORMATION In keeping with Maxon's dedicated customer support policy, we encourage you to contact us. TECHNICAL: Hours of Operation: Monday to Friday 8.30am to 5.30pm* Telephone: Facsimile: support@maxon.com.au * Public holidays excluded SALES: Hours of Operation: Monday to Friday 8.30am to 5.30pm* Telephone: Facsimile: sales@maxon.com.au * Public holidays excluded WEBSITE: Maxon has also added for the benefit of developers and integrators, a forum on our website that can be accessed to discuss this product and/or technical matters in relation to your applications. All questions raised within this portal will be answered. FORUM: ADDRESS: Maxon Electronics Australia Pty Ltd 36a Gibson Avenue, Padstow Sydney, NSW, Australia 2211 POSTAL ADDRESS Maxon Electronics Australia Pty Ltd Po Box 1, Revesby North, Sydney, NSW Australia 2212 Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 4 of 11

5 Table of Contents CONTACT INFORMATION... 4 Unimax+ HSPA I/O Board... 6 Digital Input/Output... 6 Connection:... 9 Unimax+ Setup for I/O Reporting Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 5 of 11

6 Unimax+ HSPA I/O Board Digital Input/Output A digital output opens or closes the circuit between two terminals depending on the binary state of the output. A digital input is a switch and a voltage sending device. Depending on the switch's open/closed status, Unimax+ detects a voltage or no voltage condition, which in turn generates a logical 0 or 1, ON or OFF, alarm or normal or similarly defined state. To use the I/O functionality in the Unimax+, Maxon has designed an external I/O board that allows interfacing with customer data loggers without any external circuitry. 1.1 Interface Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 6 of 11

7 I/O board 1.2 Connector 1 (CN1) Name Pin Direction Description Electrical spec Min Max Unit EXT_PWR 1 Input Power Input 7 30 V DIGT_IN_0 2 Input High 3 24 V Low 1 V ma DIGT_IN_1 3 Input High 3 24 V Low 1 V ma DIGT_OUT_0 4 Output Power Output 1 A DIGT_OUT_1 5 Output Power Output 1 A GND 6 Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 7 of 11

8 1.3 Connector 2 (CN2) Name Pin Direction Description Electrical spec Min Max Unit VDD3.3V 1 Input 3.3V Power 3.3 V DIGTAL_IN_0 2 Output Power Output 3.3 V 20 ma DIGTAL_IN_1 3 Output Power Output 3.3 V 20 ma DIGTAL_OUT_0 4 Input High 3 V Low 0.5 V 1.8 ma DIGTAL_OUT_1 5 Input High 3 V Low 0.5 V 1.8 ma GND 6 Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 8 of 11

9 Connection: Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 9 of 11

10 Unimax+ Setup for I/O Reporting Digital I/O page allows configuring what messages to be sent via SMS when an Input/Output changes state. [Figure: Digital I/O Control Page] Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 10 of 11

11 ITEM DESCRIPTION Active To enable or disable this function Trigger time when input status changes from Trigger Time low to high or from high to low Reporting Enter mobile numbers for sending SMS in Number international format. E.g. (+614.) This message will be sent via SMS to the Message reporting phone numbers when an input INPUT changes state This is the message that will trigger the outputs on or off when received from the reporting Message phone numbers. Unimax+ will ignore OUTPUT messages received from any other phone numbers. [Table: Digital I/O Control Page Information] Please contact the Maxon Technical help desk team on or support@maxon.com.au for more information on the I/O board configuration and setup of Unimax+. Unimax+ HSPA Industrial Ethernet Router I/O Board Manual Page 11 of 11