Game Boy Micro Motherboard Replacement

Size: px

Start display at page:

Download "Game Boy Micro Motherboard Replacement"

Merry Morrison
5 years ago
Views:

1 Game Boy Micro Motherboard Replacement Written By: Brendan Kelly ifixit CC BY-NC-SA Page 1 of 12

2 INTRODUCTION In this guide, we will show you how to remove and replace the motherboard and LCD. TOOLS: Phillips #00 Screwdriver (1) Spudger (1) Tweezers (1) Tri-point Y0 Screwdriver (1) ifixit CC BY-NC-SA Page 2 of 12

3 Step 1 Faceplate Locate the two circular holes on the side of the Game Boy nearest to the directional pad. Step 2 Straighten the end of a paper clip and push it into each of the circular holes. You may hear a faint click afterwards. Use the paper clip to lever the faceplate off from the unit. ifixit CC BY-NC-SA Page 3 of 12

4 Step 3 Battery Cover Remove the Phillips #00 screw on the side of the Game Boy closest to the directional pad. Once the screw has been loosened, lift the cover off the back of the device. Step 4 Once the back cover is removed, you should see that the battery is connected to the device by two wires and a plastic connector. Gently grab the wires. ifixit CC BY-NC-SA Page 4 of 12

Step 5 Carefully pull the wires until the

device, make sure the connector is put in

5 Step 5 Carefully pull the wires until the connector comes out of the device. Be careful! Don't pull too hard, or you may rip the wires out from the connector. When putting the battery back into the device, make sure the connector is put in exactly the way it came out. Step 6 Buttons Remove the two tri-wing screws on the top of the Game Boy and the two screws next to the volume/contrast switch. ifixit CC BY-NC-SA Page 5 of 12

6 Step 7 Remove the three Phillips #00 screws. Remove the two tri-wing screws. Step 8 Lift the back cover off of the Game Boy. ifixit CC BY-NC-SA Page 6 of 12

Step 9 Remove the two Phillips #00 screws from

As you are pulling off the plastic frame, the

on the lower right corner of the plastic guard.

7 Step 9 Remove the two Phillips #00 screws from the plastic frame. As you are pulling off the plastic frame, the shoulder buttons and the volume switch may fall out of the device. Underneath each shoulder button is a small spring. Do not lose them. Step 10 With a spudger, depress the small clip on the lower right corner of the plastic guard. Grab the edges of the plastic frame and lift the frame off the motherboard. ifixit CC BY-NC-SA Page 7 of 12

Step 11 Remove the two gold Phillips #00 screws from the

With your other hand, pull out the EMI shield until the tab comes

8 Step 11 Remove the two gold Phillips #00 screws from the motherboard. Step 12 With one hand, gently slide the top left end of the motherboard up and out of the front case. With your other hand, pull out the EMI shield until the tab comes out of the front case. Once the tab is pulled out from the bottom, slide the EMI shield down and out of the device. ifixit CC BY-NC-SA Page 8 of 12

Step 13 The entire motherboard is now accessible.

avoid damaging the device and its components.

Lift the motherboard and the front plastic cover

Once the front case is removed, the plastic on/off

Step 14 When you remove the motherboard from the front

9 Step 13 The entire motherboard is now accessible. Take extreme care when working with the motherboard to avoid damaging the device and its components. A small ribbon cable connects the start and select buttons to the motherboard. It can rip very easily, so do not pull on it. Lift the motherboard and the front plastic cover assembly off of the front case. Once the front case is removed, the plastic on/off switch will fall out of place. Step 14 When you remove the motherboard from the front case, the start and select buttons may fall out. If the buttons do not fall out, remove them with a pair of tweezers. ifixit CC BY-NC-SA Page 9 of 12

Step 15 Without the front case, you will be left with

The LCD screen is attached to the motherboard by a

Using metal tweezers, grab the start/select board and

Step 16 Lift the entire motherboard assembly off the

Take caution not to damage any of the gold ribbon

10 Step 15 Without the front case, you will be left with the motherboard and the plastic mount. The LCD screen is attached to the motherboard by a ribbon and can fall off the plastic mount. Using metal tweezers, grab the start/select board and slide it out gently. Step 16 Lift the entire motherboard assembly off the plastic guard. Take caution not to damage any of the gold ribbon cables on the motherboard. The LCD screen is the only thing connecting the motherboard and plastic guard. ifixit CC BY-NC-SA Page 10 of 12

Step 17 To remove the LCD screen, carefully angle it until it is

It is now possible to remove the entire motherboard assembly from

Step 18 On the plastic guard, there are two rubber pads that

These pads rest on the motherboard and sometimes stick to it.

With the rubber pads off, you may use your fingers to remove the

11 Step 17 To remove the LCD screen, carefully angle it until it is diagonal to the square hole in the plastic guard and slide it out. It is now possible to remove the entire motherboard assembly from the plastic guard. Step 18 On the plastic guard, there are two rubber pads that cover the buttons. Remove them. These pads rest on the motherboard and sometimes stick to it. If they do, peel them off. With the rubber pads off, you may use your fingers to remove the buttons to clean or replace them. When returning the buttons to the guard, they have to be put back in exactly the way they were pulled out. ifixit CC BY-NC-SA Page 11 of 12

Step 19 Motherboard The LCD screen is connected to

Use a plastic spudger to disconnect the LCD's ZIF

Step 20 Use the tip of the spudger to lift the

With both tabs lifted, pull the ribbons off the

12 Step 19 Motherboard The LCD screen is connected to the motherboard by two ribbon cables. Use a plastic spudger to disconnect the LCD's ZIF connector. Step 20 Use the tip of the spudger to lift the small, black tab holding the thin ribbon. With both tabs lifted, pull the ribbons off the motherboard and remove the LCD screen. To reassemble your device, follow these instructions in reverse order. This document was last generated on :46:48 AM. ifixit CC BY-NC-SA Page 12 of 12

Written By: Brendan Kelly

Game Boy Micro LCD Screen Replacement Written By: Brendan Kelly ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION In this guide, we'll show you how to change the LCD Screen. TOOLS: Phillips #00