Security at Fingertips.

Transcription

1 Security at Fingertips

2 Installation Guide SF1000 Version: 2.0 Date: May 2014 All design and specification declared are subject to change without notice in advance.

3

4

5 I. Use Instructions 1. Panel Description LED Indicator Fingerprint Collector Numpad / LED Indicator Key Hole Locking Key / Start Key / Enter Key Emergency Power Interface 2. Precautions Figure 1 (1) Lock comes in default demo mode, any fingerprint or password will open the lock, user must first change default Master Passcode (MPC: 98989). User must have registered at least one admin before enrolling an ordinary user. Note: The method and step of changing Master Pass Code, Enroll Administrator and Enroll Ordinary user, please refer to II.The Basic Operation. (2) Do not remove batteries when matching, enrolling or deleting fingerprints because the sudden power-down may result in data loss of fingerprint locks. (3) It is recommended to replace the fingerprint lock batteries at least once every six months to avoid damaging the circ uit due to the battery leakage. (4) Operations have a stand-by (idle) time limit of 10 seconds, lock will shut off after 10 seconds of no activity. Within 5 times matching failed, the safebox will keep locking 15 minutes, then all fingerprint / password is invalid, except mechanical key. 1

6 3. Verification mode Successful 1 Long Beep/ LED Flashes Green Access Mode Green LED es every second Failed 2 Short Beeps/ LED Flashes Red User ID Admin (995~999) Ordinary (001~994) 4. Unlock with an Emergency Mechanical Key You can open the lock using an emergency mechanical key in case the electronic component does not operate. (1) Capping the tip of the tool into the lock flap at the bottom, a little f orce to pry open the lock cover. (2) Insert the emergency key into the keyhole and rotate 90ºto unlock, as shown in Figure Reset Figure 2 Figure 3 The red reset button is on the inner side of front panel (as shown in Figure 3), it is used to restore factory setting by following steps: Press to activate lock, then long press reset button 5 seconds until you hear a long beep. 6. Battery Low Voltage Protection Please change the battery in time when you hear short sharp sounds five times made by buzzer. 7. Two ways to Unlock the Non-lock Status Alarm 2 (1) Press and at the same time push the door inward, the machine will lock automatically. (2) Lock it by the mechanical key. The alarm will be switched off after the proper locking is done.

7 II. The Basic Operation 1 Change Master Passcode 1. Enter MPC [98989] 1. Press 5 2. Enter new 5-digit code 1. Enter same code again 2 Enroll Admin Fingerprint 1. Enter MPC 1. Press 9 2. Enter User ID (995~999) Place finger 3 times 3 Enroll Admin 1. Enter MPC 1. Press 9 2. Enter User ID (995~999) 1. Enter a 6~10 digits password 1. Enter same password again 4 Enroll Ordinary User Fingerprint 1. Enter MPC or Verify Admin by Fingerprint / 1. Press 1 2. Enter User ID (001~994) Place finger 3 times 3

8 5 Enroll Ordinary User 1. Enter MPC or Verify Admin by Fingerprint / 1. Press 2 2. Enter User ID (001~994) 1. Enter a 6~10 digits password 1. Enter same password again 6 Delete User 1. Enter MPC or Verify Admin by Fingerprint / 1. Press 3 2. Enter User ID (001~994) 1. Enter same User ID again 7 Modify Verification Mode 1. Enter MPC or Verify Admin by Fingerprint / Press 4 1. Enter [111]: normal mode (all registered users) Enter [222]: safe mode (ordinary user with fingerprint + password, or admin) 8 Restore Factory Settings 1. Enter MPC or Verify Admin by Fingerprint / 1. Press 7 2. Enter [0000] 1. Enter [0000] again 4

9 Ⅲ. Preparations before Installation 1. Packing list Name Safebox Expansion screw Mechanical key Buckle Division plate Installation guide Quantity keys+ Capping tool Recommended Installation Tools Spanner Percussion drill Ⅳ.Install the Safebox 1. Structure Description Expansion bolt Expansion tube Gasket Split washer Screw nut Four mounting holes in the back panel Four mounting holes on the baseboard Expansion screw 5

10 2. Installation Procedure (1) Drill holes. Back panel 4-10mm Baseboard 4-Φ10mm 257mm 300mm 257mm (2) Fix the expansion screw in the wall. 257mm Wall Wall Put expansion bolt and expansion tube together insert into the hole. Fit on gasket, split washer and screw nut. Tighten screw nut by spanner until the expansion tube is expanded, which makes expansion bolt fixed on the wall. Take out gasket, split washer and screw nut. 6

11 (3) Mount the safe box on the wall, then fit gasket, split washer and screw nut on the expansion bolt, then tighten screw nut by spanner to make the safe box fixed on the wall. Wall Wall (4) Fix the safebox on the ground in the same way Ground Ground 7

12 (5) Install Division Plate Fix two buckles with the same height on one side. Put division plate on the buckles with the angle of inclination. Fix two buckles with the same height on the other side, then down the division plate to make it horizontal. V. Install Batteries Ⅵ. Routine Maintenance 8 1. The lock surface is forbidden to contact corrosive substances. Otherwise, the protective layer of the lock surface may be damaged, and therefore the glossiness of the lock surface may be decreased. 2. Please clean it with the adhesive sticker tape or ethyl alcohol and dry it up using the fine cloth without the batting, when the fingerprint collector is used for long time. 3. Change batteries in time when it is low (pay attention to the negative and positive). It is recommended to use four new batteries of the same brand (the alkaline battery of 1.5 V). 4. Regularly check whether screws are loose.

13 #24,Shambavi Building, 23rd Main,Marenahalli, JP Nagar 2nd Phase, Bangalore Phone: sales@esslindia.com