INSTALLATION MANUAL FOR USING YOUR THROTTLE V3. Version

Transcription

1 INSTALLATION MANUAL FOR USING YOUR THROTTLE V3 Version Aug w w w. c o k c p it f o r y o u. c o m To r s t en M ü ll e r

2 Installation manual for using your TQ Thank you for purchasing the motorized version V3 of our new COCKPITFORYOU 737 throttle quadrant. It has been assembled and tested with the greatest care. To make the installation as convenient as possible for you, we tried to describe the installation process in great detail. Should you still experience difficulties with the setup or operation of your throttle quadrant, please do not hesitate to contact us via or phone. In the near future we will release a video setup tutorial in addition to this manual that will guide you through all the necessary steps. We hope you will have as much fun flying your new TQ as we had engineering and assembling it. 1. Before getting started download CFY_TQ.zip download vjoy.rar 2. Connecting your Throttlew Your motorized butterfly comes with 1 Ethernet port and 1 female PC power supply. PC power supply ( V / 50-60Hz) SiteSeite 2 von 20

3 Ethernet cable:plug in the Ethernet cable into a free port of an Ethernet switch. Minimum requirement for switch is 100 Mbit. 3. installation software 1. Create new folder "CFY" on drive C: 2. Extract CFY_TQ.zip to C: CFY 3. In the folder C:\CFY double click the file "vjoy_216_150815". Installation may take 5 minutes. Restart computer. If installation seems to be halted after approx 5 minutes you can restart computer. SiteSeite 3 von 20

4 4. In the folder C:\CFY double click the file "setup" installation folder Change the in "C: CFY" SiteSeite 4 von 20

5 Press Next and follow installation instructions Press Understood SiteSeite 5 von 20

6 The calibration is Carried out (at first start) The "TQ V3" is ready 5. Start your flight simulator SiteSeite 6 von 20

7 The "TQ V3" connects to your flight simulator 6. Start your AddOn Software None or TQ V3 connects to prosim737 or SimAvionics or PM 7. Sign the Trim button on the SiteSeite 7 von 20

8 Yoke (Soon automatically) Open FSUIPC, select Buttons + Switches Press the Nose up trim switch on your yoke Check the Select for FS control box Select Offset Word Set from the list Set the first offset to x9093 and the parameter to 2 The Control sent when the button is released: Select Offset Word Set from the list Set the first offset to x9093 and the parameter to 0 Press OK to save these changes SiteSeite 8 von 20

9 Open FSUIPC, select Buttons + Switches Check the Select for FS control box Select Offset Word Set from the list Set the first offset to x9093 and the parameter to 1 The Control sent when the button is released: Select Offset Word Set from the list Set the first offset to x9093 and the parameter to 0 Press OK to save these changes SiteSeite 9 von 20

10 All automatically created joystick assignmntin FS delete!!! SiteSeite 10 von 20

11 Advanced settings: FS2004 without AddOn FS FSX without AddOn FS P3D without AddOn => no adjustments necessary / FSUIPC must be installed => no adjustments necessary / FSUIPC must be installed => no adjustments necessary / FSUIPC must be installed FS XPlane without AddOn => no adjustments necessary / XPUIPC must be installed PM IFly Sim-Avionics PMDG NGX ProSim737 For IFly => no adjustments necessary / FSUIPC must be installed => see item 11 / FSUIPC must be installed => see item 12 / FSUIPC or XPUIPC (XPlane) must be installed => see item 13 / FSUIPC must be installed => see item 14 / FSUIPC must be installed 11. IFly to FSUIPC installed. SiteSeite 11 von 20

12 12. For Sim-Avionics Sim-Avionics Setup with Cockpit For You Throttle An FSUIPC connection is require, so the CFY controller software should either be run on the FS computer, or run on a remote computer with WideClient running. Sim -Avionics Server Configuration 1) FSUIPC_IO.INI Set Multi Function Offset MULTI_FUNCTION=53FE Remove 5418 offset from PARKING_BRAKE=5418 [FSUIPC_INPUTS] PARKING_BRAKE= ENGINE_L_FUEL_CONTROL_SWITCH=5452 ENGINE_R_FUEL_CONTROL_SWITCH=5453 Add Autothrottle output offsets [FSUIPC_OUTPUTS] COMMANDED_THROTTLE_L_POSITION=53E0 COMMANDED_THROTTLE_R_POSITION=53E2 THRUST_REF_MODE=53E4 2) Control Panel Tab Enable FSUIPC Outputs ON 3) Flight Controls 1 Tab Parking Brake External Flaps External Gear External Elevator Trim via FSUIPC Toe brakes release Parking Brake Enable Simple Braking 4) Flight Controls 2 Tab Main Throttles Reversers OFF OFF ON OFF OFF OFF FDS Pro Throttle/Sys Controller Axis/SIOC SIOC / Offsets 52DA and 52DC SiteSeite 12 von 20

13 CFY FS FSUIPC oftware ConfigConfigurationuration 1) FSUIPC > Axis Assignment Add "Parking Brake" to Brake Axis Detect Brake Axis Control sent when range entered = Parking Brake Up Dn OFF ON From = 95% of brake pedal To = 100% of brake pedal 2) FSUIPC > Buttons Trim Up Offset Word Set x Repeat ON Offset Word Set x Trim Down Offset Word Set x Repeat ON Offset Word Set x SiteSeite 13 von 20

14 13. For PMDG_NGX Current FSUIPC4 version! As of today: 4,949 FSUIPC4 Current SimConnect version! Configuring the PMDG ini open Windows Explorer ( where FSX is instaled ), open Computer, Drive FSX, open folder "PMDG" open folder "PMDG 737 NGX" SiteSeite 14 von 20

15 " 737 NGX_Options.ini" open Writing at the end of the text following this: [SDK] EnableDataBroadcast=1 Please check carefully!!! The text must be written exactly!!! In small and capital letters Be sure!!! The text must be written exactly!!! In small and capital letters Ensure!!! SiteSeite 15 von 20

16 Save and close the file SiteSeite 16 von 20

17 14. For ProSim737 Setting in ProSim737 Config / Drivers Generic COM port/tcp diver => Enabled SiteSeite 17 von 20

18 SiteSeite 18 von 20

19 Sit back relax and enjoy your flight. This is it. By now your 737 throttle quadrant should be up and running. In case you have any further questions or you are experiencing difficulties, please do not hesitate to contact us via or phone. Torsten Müller Berlin, Germany 2017 SiteSeite 19 von 20

20 SiteSeite 20 von 20