VIPA HMI. Touch Panel 605-1B1E0 Manual

Transcription

1 VIPA HMI Touch Panel 605-1B1E0 Manual HB160E_TP RE_605-1B1E0 Rev. 10/16 April 2010

2 Copyright VIPA GmbH. All Rights Reserved. This document contains proprietary information of VIPA and is not to be disclosed or used except in accordance with applicable agreements. This material is protected by the copyright laws. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to VIPA), except in accordance with applicable agreements, contracts or licensing, without the express written consent of VIPA and the business management owner of the material. For permission to reproduce or distribute, please contact: VIPA, Gesellschaft für Visualisierung und Prozessautomatisierung mbh Ohmstraße 4, D Herzogenaurach, Germany Tel.: +49 (91 32) Fax.: Note Every effort has been made to ensure that the information contained in this document was complete and accurate at the time of publishing. Nevertheless, the authors retain the right to modify the information. This customer document describes all the hardware units and functions known at the present time. Descriptions may be included for units which are not present at the customer site. The exact scope of delivery is described in the respective purchase contract. CE Conformity Hereby, VIPA GmbH declares that the products and systems are in compliance with the essential requirements and other relevant provisions of the following directives: 2004/108/EC Electromagnetic Compatibility Directive 2006/95/EC Low Voltage Directive Conformity is indicated by the CE marking affixed to the product. Conformity Information For more information regarding CE marking and Declaration of Conformity (DoC), please contact your local VIPA customer service organization. Trademarks VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V, System 500S and Commander Compact are registered trademarks of VIPA Gesellschaft für Visualisierung und Prozessautomatisierung mbh. SPEED7 is a registered trademark of profichip GmbH. SIMATIC, STEP, SINEC, S7-300 and S7-400 are registered trademarks of Siemens AG. Microsoft und Windows are registered trademarks of Microsoft Inc., USA. Portable Document Format (PDF) and Postscript are registered trademarks of Adobe Systems, Inc. All other trademarks, logos and service or product marks specified herein are owned by their respective companies. Information product support Contact your local VIPA Customer Service Organization representative if you wish to report errors or questions regarding the contents of this document. If you are unable to locate a customer service center, contact VIPA as follows: VIPA GmbH, Ohmstraße 4, Herzogenaurach, Germany Telefax: documentation@vipa.de Technical support Contact your local VIPA Customer Service Organization representative if you encounter problems with the product or have questions regarding the product. If you are unable to locate a customer service center, contact VIPA as follows: VIPA GmbH, Ohmstraße 4, Herzogenaurach, Germany Telephone: /1180 (Hotline) support@vipa.de

3 Manual VIPA System HMI Contents Contents About this manual... 1 Safety information... 2 Chapter 1 Hardware description Safety information for Users Properties Structure Components Dimensions Technical Data Chapter 2 Deployment Touch Panel Installation Commissioning Connection to a PLC system Operating system Windows CE Communication via ActiveSync Integrated Server Access to the network resources Integration to WLAN network Firmware update Chapter 3 Installation Guidelines Basic rules for the EMC-equitable assembly of installations EMC-equitable assembly EMC-equitable cabling Special precautions providing high noise immunity Checklist for the EMC-compliant installation of controllers Appendix...A-1 Index...A-1 HB160E - TP - RE_605-1B1E0 - Rev. 10/16 i

4 Contents Manual VIPA System HMI ii HB160E - TP - RE_605-1B1E0 - Rev. 10/16

5 Manual VIPA System HMI About this manual About this Manual The manual describes the Touch Panel TP 605MQ from VIPA. Here you find detailed descriptions of the Touch Panel beside a product overview. Here you get information about structure, project engineering and operation of the Touch panels from VIPA. Overview Chapter 1: Hardware description During this chapter you get hints for deployment of the Touch Panel TP 605MQ from VIPA. Besides of a description of the single components of the Touch Panel, you will also find the dimensions that are required for the installation. The chapter closes with the technical data. Chapter 2: Deployment Touch Panel This chapter deals with the employment of the Touch Panel. At the start of the chapter you receive information about the assembly and the connection of the Touch Panel. The main part of the chapter introduces Windows CE and the various communication options offered by the Touch Panel. Chapter 3: Installation guidelines This chapter helps you to install an interference-free automation system. First, possible interference sources and their interaction mechanisms are shown, followed by basic rules for guaranteeing EMC. Afterwards you'll find information about assembly and cabling following EMC rules. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1

6 About this manual Manual VIPA System HMI Objective and contents This manual describes the Touch Panels from VIPA. The manual consists of chapters. Every chapter provides the description of one specific topic. It describes the installation, project engineering, usage and the technical data. This manual is part of the documentation package with order number VIPA HB160E_TP and relevant for: Product Order number as of state: HW OS TP 605MQ VIPA 605-1B1E0 01 Windows CE V. 5.0 Guide to the document Availability This manual provides the following guides: An overall table of contents at the beginning of the manual An overview of the topics for every chapter An index at the end of the manual. The manual is available in: printed form, on paper in electronic form as PDF-file (Adobe Acrobat Reader) Description conventions [Button] [Key] Display output Keyboard entry Terms Buttons are put in brackets e.g. [NEXT] or [OK]. Key entry are put in brackets e.g. [STRG]+[A]. Display outputs are illustrated as Courier e.g. \flashdisk> Keyboard entries are illustrated as Courier bold e.g. \flashdisk> Dir Menus, Display elements, terms are italics. Icons Headings Important passages in the text are highlighted by following icons and headings: Danger! Immediate or likely danger. Personal injury is possible. Attention! Damages to property is likely if these warnings are not heeded. Note! Supplementary information and useful tips. 2 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

7 Manual VIPA System HMI Safety information Safety information Applications conforming with specifications The Touch Panels are constructed and manufactured for: VIPA CPUs 11x, 21x, 31x, 51x and S7-300/400 from Siemens communication and process control general control and automation applications industrial applications operation within the environmental conditions specified in the technical data installation into a cubicle Danger! This device is not certified for applications in in explosive environments (EX-zone) Documentation The manual must be available to all personnel in the project design department installation department commissioning operation The following conditions must be met before using or commissioning the components described in this manual: Modification to the process control system should only be carried out when the system has been disconnected from power! Installation and modifications only by properly trained personnel The national rules and regulations of the respective country must be satisfied (installation, safety, EMC...) Disposal National rules and regulations apply to the disposal of the unit! HB160E - TP - RE_605-1B1E0 - Rev. 10/16 3

8 Safety information Manual VIPA System HMI 4 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

9 Manual VIPA HMI Chapter 1 Hardware description Chapter 1 Hardware description Overview During this chapter you get hints for deployment of the Touch Panel TP 605MQ from VIPA. Besides of a description of the single components of the Touch Panel, you will also find the dimensions that are required for the installation. The chapter closes with the technical data. Content Topic Page Chapter 1 Hardware description Safety information for Users Properties Structure Components Dimensions Technical Data HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1-1

10 Chapter 1 Hardware description Manual VIPA HMI Safety information for Users Handling of electrostatic sensitive modules VIPA modules make use of highly integrated components in MOStechnology. These components are extremely sensitive to over-voltages that can occur during electrostatic discharges. The following symbol is attached to modules that can be destroyed by electrostatic discharges: The symbol is located on the module, the module rack or on packing material and it indicates the presence of electrostatic sensitive equipment. It is possible that electrostatic sensitive equipment is destroyed by energies and voltages that are far less than the human threshold of perception. These voltages can occur where persons do not discharge themselves before handling electrostatic sensitive modules and they can damage components thereby, causing the module to become inoperable or unusable. Modules that have been damaged by electrostatic discharges may fail after a temperature change, mechanical shock or changes in the electrical load. Only the consequent implementation of protection devices and meticulous attention to the applicable rules and regulations for handling the respective equipment can prevent failures of electrostatic sensitive modules. Shipping of electrostatic sensitive modules Modules have to be shipped in the original packing material. Measurements and alterations on electrostatic sensitive modules When you are conducting measurements on electrostatic sensitive modules you should take the following precautions: Floating instruments must be discharged before use. Instruments must be grounded. Modifying electrostatic sensitive modules you should only use soldering irons with grounded tips. Attention! Personnel and instruments should be grounded when working on electrostatic sensitive modules. 1-2 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

11 Manual VIPA HMI Chapter 1 Hardware description Properties General The Touch Panel allows you to visualize and alter operating states and recent process values of a connected PLC. TP 605MQ 605-1B1E0 The VIPA Touch Panel is a compact and modular embedded PC based on Windows CE. Besides of the extensive Windows CE functions the Touch Panel offers varied communication possibilities. Here the Touch Panel can simply be configured, controlled and remoted. By including a selectable HMI/SCADA runtime the Touch Panel is particularly suitable for monitoring and controlling of process cycles. Microsoft Windows CE V. 5.0 (full version as option) Different HMI/SCADA-Runtime selectable Work memory 64Mbyte about 6Mbyte memory for user data on Board CF-Card II and MMC/SD card slot Horizontal and vertical display selectable in 90 steps RS232, RS422/485, MPI, Profibus DP slave, Ethernet, USB-A and USB-B interfaces on board Robust aluminium die casting case Display resolution up to 240 x 320 / 320 x 240 (16 levels) Battery backed clock Resistive touch screen Easy mounting via integrated pivoted lever Protection class IP65 (frontal) Order data Type Order number Description TP 605MQ VIPA 605-1B1E0 5.7" QVGA LCD monochrom, MPI/Profibus DP/RS485, RS232, RS422/485, USB-A, USB-B, Ethernet RJ45 HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1-3

12 Chapter 1 Hardware description Manual VIPA HMI Structure Front view 1 Touch Panel [1] Slot for storage medium (CF, SD/MMC) [2] Connection for interfaces and power supply [3] Display with touch sensitive area (touch screen) 3 2 Side view 1 [1] Compact Flash [2] MMC / SD 2 Note! Please regard that the Touch Panel always has to be supplied with external voltage! 1-4 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

13 Manual VIPA HMI Chapter 1 Hardware description Bottom view (Interfaces) TP 605MQ 5.7'' 605-1B1E Components [1] RS422/485 interface COM 2 [2] RS232 interface COM 1 [3] MPI/Profibus DP/RS485 interface [4] "Host"-USB-A interface [5] "Slave"-USB-B interface [6] RJ45 jack for Ethernet communication [7] Slot for DC 24V voltage supply [8] Slot for CF/SD/MMC storage medium HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1-5

14 Chapter 1 Hardware description Manual VIPA HMI Components Memory management Work memory Flash disc USB storage media Slot for CF The following memory systems are available for every Touch Panel: 64Mbyte work memory 32Mbyte Flash-Disk (6Mbyte for user data) USB storage media using "Host"-USB-A interface Slot for CF (Type II) Slot for MMC/SD Every Touch Panel has a work memory with a size of 64Mbyte. The work memory is not buffered and is deleted after shut down. Please regard that also registry entries are stored in the work memory that are set back to default settings after the next re-boot. You may save them permanently by means of the KuK Tools (within consignment). As internal permanent storage medium every Touch Panel has a flash disc with a size of 32Mbyte (6Mbyte user data). After the start of Windows CE this memory is listed as Flashdisk at My Device. The connection of USB sticks and USB drives by use of the "Host"-USB-A interface is supported by the Touch Panel. After connection the storage media is listed as Hard Disk at My Device. Here you may plug a CompactFlash type II. The card may be plugged and removed during runtime and is immediately listed as Storage Card at My Device. Every CompactFlash storage module has a pulling edge. Hold the CompactFlash in the way that the pulling edge points to the left side. Push the storage module without much power into the slot until the impact. To remove the card touch it at the pulling edge and pull. Slot for SD/MMC Security flap for memory cards At this slot you may plug storage modules of the type SD or MMC. The card may be plugged and removed during runtime and is immediately listed as SDMMC Card at My Device. Please take care to plug the according card as shown at the backside of the Touch Panel. At the left side of the Touch Panel are the card slots for memory cards. The cards are visibly covered by a security flap and are thus secured from slipping out. Please take care to pull the security flap back before plugging or pulling a memory card like shown in the illustration and put it back again afterwards. When plugging, the security flap additionally snaps into position above the plugged memory card. 1-6 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

15 Manual VIPA HMI Chapter 1 Hardware description RS422/485 interface Logical states represented by voltage differences between the 4 cores Serial bus connection in 4-wire technology using full duplex mode Data communications up to a max. distance of 500m Data communication rate up to 115.2kBaud Connection RS422/485 9pin jack Connection RS422 (isolated) Pin RS422/485 1 n.c. 2 n.c. 3 TxD+ (Line A) 4 RxD+ (Line A) 5 M5V 6 P5V 7 n.c. 8 TxD- (Line B) 9 RxD- (Line B) RS422 TxD+ (A) TxD- (B) RxD+ (A) RxD- (B) M5V P5V Shield Periphery RxD+ TxD+ Serial bus connection in 2-wire technology using half duplex mode Connection RS485 (isolated) RS485 Periphery TxD+ (A) TxD- (B) 3 8 RxD+/TxD+ RxD+ (A) 4 RxD- (B) M5V P5V Shield Periphery RxD+/TxD+ TxD- RxD- RxD-/TxD- RxD-/TxD- Profibus DP / MPI interface Connection RS485 9pin jack Connection RS485 RS485 Pin RS485 1 n.c M24V RxD/TxD-P(B) RxD/TxD-P (Line B) RxD/TxD-P(B) 8 8 RTS 4 4 RTS 3 M5V M5V P5V P5V 6 P24V P24V Shield 8 RxD/TxD-N (Line A) 9 n.c. Periphery RxD/TxD-P(B) RxD/TxD-N(A) Shield HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1-7

16 Chapter 1 Hardware description Manual VIPA HMI RS232 interface Interface is compatible to the COM interface of a PC Logical signals as voltage levels Point-to-point links with serial full-duplex transfer in two-wire technology up to 15m distance Data transfer rate up to 115.2kBaud Connection RS232 9pin plug Connection RS Pin RS232 1 CD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI TxD RxD GND RTS CTS Shield RS Periphery RxD TxD GND Shield Ethernet connection An RJ45 jack provides the interface to the twisted pair cable, required for Ethernet. The pin assignment of this jack is as follows: pin RJ45 jack: Pin Signal 1 Transmit + 2 Transmit - 3 Receive Receive HB160E - TP - RE_605-1B1E0 - Rev. 10/16

17 Manual VIPA HMI Chapter 1 Hardware description "Host"-USB-A Using the "Host"-USB-A interface mouse, keyboard, USB stick ore USB hard discs can be connected. The pin assignment is as follows: "Host"-USB-A: Pin Assignment 1 VCC 2 DM 3 DP 4 GND "Slave"-USB-B For project transfer with Microsoft ActiveSync a programming cable can be connected using the "Slave"-USB-B interface. The pin assignment is as follows: "Slave"-USB-B: Pin Assignment 1 VCC 2 DM 3 DP 4 GND VIPA USB-B Programming cable The USB-A interface of your PC can be connected to the "Slave"-USB-B interface of your Touch Panel deploying the USB programming cable. The USB programming cable is delivered by VIPA with order No. VIPA 670-0KB10. Power supply DC 24V The Touch Panel has got an integrated power supply. The power supply has to be provided with DC 24V ( V). For this you find an according DC 24V slot at the bottom side. The power supply is protected against inverse polarity and overcurrent. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 1-9

18 Chapter 1 Hardware description Manual VIPA HMI Dimensions installation width width installation hight hight installation depth Installation dimensions For the installation of the Touch Panel in control cabinets and desks the following dimensions are necessary: 5.7'' 605-1B1E0 Front panel width Installation cutting (W x H) Front panel (W x H) Display size (W x H) Back side (W x H x D) Installation depth mm 200 x 144mm 212 x 156mm x 86.4mm 198 x 142 x 37mm 37mm Note! The degrees of protection are only guaranteed when the following is observed: Material thickness at the mounting cut-out: mm the deviation from the plane for the panel cut-out is 0.5mm. This condition must be fulfilled for the mounted HMI device Permissible surface roughness in the area of the seal: 120µm (friction coefficient 120) 1-10 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

19 Manual VIPA HMI Chapter 1 Hardware description Technical Data TP 605MQ Electrical data VIPA 605-1B1E0 Nominal supply voltage DC 24V ( V) ESD/Burst Acc. IEC / IEC (up to level 3) Shock resistance Acc. IEC / IEC (1G/12G) Level of noise suppression Acc. IEC Mark of conformity and certification - Clock and housing Processor Xscale 520MHz Clock Hardware clock, buffered Housing - protection class Solid aluminium case - Front IP 65 - Back IP 20 Environment conditions Mounting position horizontally/vertically Operating temperature C Relative humidity max. 85% Storing / Transport temperature -20 to +60 C Display Size 5.7" (115.2 x 86.4mm) Resolution 240 x 320 / 320 x 240 Colors STN LCD monochrome (16 levels) MTBF Backlights (25 C) ca h Peripherals Touch screen resistive external Mouse, Keyboard USB Memory Type 32Mbyte Flash / 64Mbyte RAM Available memory for user data ca. 6Mbyte CF Card Slot Type II yes SD/MMC Push-Push-Slot yes Interfaces MPI (12Mbits), Profibus DP RS485 isolated serial RS232 COM1 serial RS422/485 isolated COM 2 USB USB-A, USB-B Ethernet 10/100 RJ45 Electrical Data Nominal supply voltage DC 24V ( V) Nominal current 0.4A Housing Mounting via 4 integrated pivoted lever Dimensions and weight Front side (W x H) 212 x 156mm Back side (W x H x D) 198 x 142 x 37mm Installation cutting (W x H) 200 x 144mm (Front panel width: mm) Weight 1560g HB160E - TP - RE_605-1B1E0 - Rev. 10/

20 Chapter 1 Hardware description Manual VIPA HMI 1-12 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

21 Manual VIPA HMI Chapter 2 Deployment Touch Panel Chapter 2 Deployment Touch Panel Overview This chapter deals with the employment of the Touch Panel. At the start of the chapter you receive information about the assembly and the connection of the Touch Panel. The main part of the chapter introduces Windows CE and the various communication options offered by the Touch Panel. Content Topic Page Chapter 2 Deployment Touch Panel Installation Commissioning Connection to a PLC system Operating system Windows CE Communication via ActiveSync Integrated Server Access to the network resources Integration to WLAN network Firmware update HB160E - TP - RE_605-1B1E0 - Rev. 10/16 2-1

22 Chapter 2 Deployment Touch Panel Manual VIPA HMI Installation Overview The Touch Panel is suitable for the installation in operating tables and control cabinet fronts. The installation happens via the backside. The Touch Panel is provided with a patented integrated fixing technique that allows an easy connection with a simple screwdriver. Due to the fact that the Touch Panel has a plug connector for bus connection and voltage supply, a fast and easy device change is possible. Installation cutting For the installation into a operating tableau and control cabinet fronts, the Touch Panel requires the following front plate cutting: W H Touch Panel W x H in mm 605-1B1E0 200 x 144 Installation The fixing technique is integrated in the casing of the Touch Panel and accessible via the backside. For the installation, a small slit screwdriver is required. Push the operator panel [3] from the front side into the front panel cutting [1] until it touches the panel with the seal [2]. Now bolt the lever [5] clockwise with the screwdriver [4] until it rotates to the outside. Further screwing bolts the lever to the front panel until it holds this to the control cabinet front HB160E - TP - RE_605-1B1E0 - Rev. 10/16

23 Manual VIPA HMI Chapter 2 Deployment Touch Panel Connect power supply 1 For the cabling of the DC 24V power supply green plugs with CageClamp technology are deployed. The spring-clip connector technology simplifies the wiring requirements for signaling and power cables. In contrast to screw terminal connections, spring-clip wiring is vibration proof. Here also you may connect wires with a cross-section of 0.08mm 2 to 2.5mm 2. You can use flexible wires without end case as well as stiff wires. You fix the conductors to the CageClamps like this: 2 DC 24V [1] Round opening for wires [2] Locking (orange) for screwdriver [3] Test point for 2mm test tip The picture on the left side shows the cabling step by step from top view. 3 For cabling you push the locking vertical to the inside with a suiting screwdriver and hold the screwdriver in this position. Insert the insulation-striped wire into the round opening. You may use wires with a cross-section from 0.08mm 2 to 2.5mm 2. By removing the screwdriver the wire is connected safely with the plug connector via a spring. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 2-3

24 Chapter 2 Deployment Touch Panel Manual VIPA HMI Commissioning Attention! Before commissioning the device must be brought to room temperature. At condensation the device must be absolutely dry before connected to power. To avoid overheat during operation the device must not be laid open to direct sun light. After opening the control cabinet or desk, there are parts with possible dangerous voltage available. For all signal connections only screened cables are permitted. Signal cables must not be let within the same cable shaft as high voltage cables. VIPA Startup Manager As soon as the Touch Panel is provided by power supply the Touch Panel starts with "user area" of the VIPA Startup Manager: User area Advanced On delivery the button [Advanced] is shown at the starting screen. Further buttons and their properties may be configured in the administrator area with the button [Settings] or freely programmed by means of an XML editor at the file startup.xml in the directory StartupMngr > flashdisc. Startup.xml The file startup.xml may be found at StartupMngr > flashdisc. By means of an XML editor the Startup Manager may be individually adapted. 2-4 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

25 Manual VIPA HMI Chapter 2 Deployment Touch Panel VIPA Startup- Manager With clicking to [Advanced] the administrator area is opened. On delivery there are the following buttons: Administrator area KuK Tools To permanently store changes within the Registry after PowerOFF - PowerON the program KuK Tools is to be used. The program may be executed by clicking to the button [KuK Tools]. To permanently store the registry file click at the button [Store] of "Permanent Registry". Backup With [Backup] the files of the flash disk and the Registry settings may be stored. Restore The backed up files may be restored by [Restore]. Normal With this button you may return to the user area. Control Panel With the button [Control Panel] or with Start > Settings > Control Panel the system settings like brightness and contrast of the display may be preset or the display may be re-calibrated. Here the communication interfaces may also be configured. Exit The VIPA Startup Manager is closed by [Exit] and the system returns to the Windows operating system. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 2-5

26 Chapter 2 Deployment Touch Panel Manual VIPA HMI Settings Buttons may be configured with [Settings]. Here buttons may be added or removed respectively assigned with programs. Main Here general settings may be established. A new background picture may be loaded at "Background...". With "Font Color" and "Back Color" the color of the button font and of the button may be preset. The position of the buttons may be changed by "Position". Enabling "Run on Startup" with the system start the functions established at "Settings" are activated. With disabling "Run on Startup" the Touch Panel starts with the Windows operating system. The functions preset at "Settings" are ignored. With enabling "Enable User Interface" the Touch Panel starts with the Startup Manager, the listed functions of "Copy" and "Execute" are executed and the program marked with "Autostart" is executed. If "Enable User Interface" is disabled, the Touch Panel starts without Startup Manager but in the background the listed functions of "Copy" and "Execute" are executed. Then the system return to the Windows operating system. A program marked with "Autostart" is not executed. Note! To remain the settings permanently, they have to be saved with KuK-Tools > Save Registry. 2-6 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

27 Manual VIPA HMI Chapter 2 Deployment Touch Panel Fixed Here the buttons are listed, which may not be changed in the user respectively administrator area. Custom Here new buttons may be configured and assigned with corresponding programs. You may choose "Normal" for the user area or "Advanced" for the administrator area. With [+] a new button may be added. Designate the button and click at [...] to assign the button to a program. The button may be removed with [-]. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 2-7

28 Chapter 2 Deployment Touch Panel Manual VIPA HMI Password The administrator area may be protected by a password. Here you may enter respectively change the password of the administrator area. If you click within the user area to the button [Advanced] and a password is defined, you were prompted to enter the password. If there is no password defined, the administrator area is opened. On delivery there is no password preset. If you have forgot you password by enabling the checkbox "Show Password" the password may be displayed. Copy Here with the startup of the panel files may be copied e.g. from flash disk to Windows. The files to be copied are added by [+]. With [-] the corresponding file is removed from the list. With [...] the file may be downloaded. 2-8 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

29 Manual VIPA HMI Chapter 2 Deployment Touch Panel Execute Here programs may be added, which have to start in the background during startup e.g. VNC server or transport services. With enabling the checkbox "Autostart" the program is always executed on startup after the preset "Delay time". On delivery the program of your run time version is preset. HB160E - TP - RE_605-1B1E0 - Rev. 10/16 2-9

30 Chapter 2 Deployment Touch Panel Manual VIPA HMI About Here you may find the current version of the VIPA Startup-Manager. Control Panel To configure the COM2 interface on the Touch Panel start via the button "Control Panel" the tool "Com2 Configuration". Configuration COM2 RS422/485 In the opened dialog window you activate the RS485 or the RS422 interface. Default: RS485 To remain the settings permanently, they have to be saved with KuK-Tools > Save Registry. To activate the changes the Touch Panel has to be restarted after configuration HB160E - TP - RE_605-1B1E0 - Rev. 10/16

31 Manual VIPA HMI Chapter 2 Deployment Touch Panel Configuration MPI/DP slave To configure the MPI/DP interface on the Touch Panel start via "Control Panel" the tool "MPI/DP Slave Configuration". Default: MPI - Address 1 The following settings are only required if not communicate via Movicon or zenon. Configuration DP slave Via mode the interface could be set up on "DP Slave". Note! It is possible to set up the DP slave with the tool via software, but the hardware of the Touch Panel do not support this. In this case MPI does not work either. To remain the settings permanently, they have to be saved with KuK-Tools > Save Registry. To activate the changes the Touch Panel has to be restarted after configuration. HB160E - TP - RE_605-1B1E0 - Rev. 10/

32 Chapter 2 Deployment Touch Panel Manual VIPA HMI Connection to a PLC system For the inclusion into your PLC system several HMI/SCADA projectengineering platforms are at your disposal that has to be installed at an external PC. Here you may create your project, where appropriate simulate it and transfer it to the Touch Panel via a connection that you ve entered before. Via the at the Touch Panel pre-installed runtime version of the HMI/SCADA project engineering platforms your project is run able. By using the according communication driver, the Touch Panel supports connecting options to the PLC via MPI, field bus and Ethernet. During the operation your operating device communicates with the according PLC and reacts to the application courses in the PLC according to the configured processes. Via dialogs configured before, process values may be monitored graphically, altered and evaluated. PC Touch Panel HMI/SCADA Runtime - ftp-server - http-server - Telnet - VNC Touch Panel MMC/SD/CF HMI/ SCADA MS ActiveSync, ftp, http, Telnet, VNC Fieldbus, MPI, Ethernet PLC CPU. PLC. CPU 2-12 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

33 Manual VIPA HMI Chapter 2 Deployment Touch Panel Operating system Windows CE Windows CE Windows CE Core 5.0 Windows CE Professional Plus 5.0 Differences Core- and Professional-Plus version Within the consignment of the Touch Panel is the operating system Microsoft Windows CE V It is an OEM licensed English version. The newly developed standard Windows CE allows devices that are communicating with each other to exchange information with Windows based devices and to establish connections to the Internet. Microsoft Windows CE is a 32bit, open and scalable platform for a multiplicity of communication and data processing devices. The functions like multi-tasking and multi-threading are supported by this operating system. As default Microsoft Windows CE Core 5.0 is delivered and optionally Microsoft Windows CE Professional Plus 5.0. The version may be found at a label at the backside of your Touch Panel. This version is a Windows operating system reduced to the absolute essentials with mouse operation (touch screen) that requires only small hardware resources. Here the 2 icons "My Device" and "Recycle Bin" may exclusively be found at the Desktop. The Professional-Plus version is an enhanced Core version. Here among others some file viewer, an Internet browser and bluetooth support are integrated. On the desktop besides many icons a mouse pointer is displayed at the pen position. As soon as the pen is hold at one position the context menu is displayed. Features Windows CE Core 5.0 Professional Plus 5.0 ftp, http, Telnet and VNC server x x RAS server - x ActiveSync file transfer x x (USB, RS232, Ethernet) RDP (Remote Desktop Protocol) - x Internet Explorer 6 - x Registry Editor x x WordPad - x Mouse pointer - x USB keyboard driver x x HP printer driver x x (COM, Ethernet, USB) Bluetooth USB stick support - x (Keyboard, mouse, modem, network) WLAN Support (SD Card, USB-Stick) x x File viewer for Word, Excel, - x PowerPoint and PDF VIPA Startup Manager x x HB160E - TP - RE_605-1B1E0 - Rev. 10/

34 Chapter 2 Deployment Touch Panel Manual VIPA HMI Differences to the standard Windows operation Pen entry Please regard that for the deployment of Windows CE a thorough knowledge of operating Windows are assumed. Here are only shown the differences to a "standard" Windows operating system. You re operating the Touch Panel by means of a pencil res. with the finger. When touching an area at the touch screen this area is recognized and the program reacts accordingly. The following types of entry are differentiated: Double click A double click has to be executed like mouse operation by touching the area at the screen twice. A double click on an object open res. executes this. Drag By tapping on an object and then dragging you may move the object on the screen. If no object is selected, a frame is created by the dragging that selects the touched objects. Characteristics with Windows CE Professional Plus V. 5.0 In the Professional Plus version mouse functions are fully supported. As soon as the touch screen is touched with the pen, a mouse pointer is shown on the desktop at the pen position. To show the context menu you can either press the right key of your mouse connected by USB or hold the pen on one position. Navigation within the dialog window Exit Windows (shut down) The windows may be moved via the head bar. Here you may also find the [OK] button to confirm entries and the [X] button for exiting the dialog. You may not exit Windows. By switching the power supply off and on again you may restart Windows. Before a reboot you should always save your data res. close all running applications to avoid data loss. Note! Please regard that made changes are set back after PowerOFF-PowerON and are only stored via Save Registry which is to be found at Start > Programs > KuK Tools HB160E - TP - RE_605-1B1E0 - Rev. 10/16

35 Manual VIPA HMI Chapter 2 Deployment Touch Panel Structure Icon Via icons on the desktop you gain direct access to the application related to the icon. 2 Desktop The desktop is the screen that is shown after login at Windows CE. It contains e.g. links to the mostly used applications res. system components. 3 Task bar The task bar is part of the desktop. When opening an application, a document or a window, every running object is displayed as button on the task bar. Via this buttons you may easily change between the open windows. Task bar Basically the task bar has the following structure: Start button This button offers you access to all components of your Touch Panel like e.g. applications, system settings, file browser etc. 2 Open applications 3 Network connection 4 Desktop direction 5 Keyboard layout For every open application a button is to be found in the task bar. There is no button for minimizing. The switch between the applications happens via this buttons. As soon as your Touch Panel is connected via Ethernet you may here display the Ethernet address. If there is no connection via Ethernet, the symbol is displayed crossed out. This symbol allows you to switch between 2 desktop directions. The position setting happens in steps of 90 and can be set via double click in a dialog window. If you ve connected a keyboard you may choose the wanted language layout via this button. 6 Time This area shows the time that you may change via double click. 7 Show desktop All windows are minimized and the desktop is shown. 8 Software keyboard This button displays a keyboard at the screen. "Hide Input Panel" hides the keyboard again. HB160E - TP - RE_605-1B1E0 - Rev. 10/

36 Chapter 2 Deployment Touch Panel Manual VIPA HMI Software keyboard The button allows you to select one of the available software keyboards. At the moment the following standard keyboards are implemented: Software keyboard Keyboard Normal: At pushed SHIFT key: At pushed [a ü] key: Note! Please regard that the umlauts äöü may exclusively entered via the software keyboard Keyboard. Software keyboard Large KB Normal: At pushed SHIFT key: Meaning: Home Position 1 End End BS Backspace up dn lt rt pgup Page pgdn Page ins Insert del Delete Tab Tabulator Shift Caps/Lock Hide keyboard The software keyboard allows you to enter key entries without connecting an external keyboard. As soon as an entry is required the software keyboard is automatically shown. Hide Input Panel hides the keyboard again HB160E - TP - RE_605-1B1E0 - Rev. 10/16

37 Manual VIPA HMI Chapter 2 Deployment Touch Panel System setting (Control Panel) Due to the fact that many components of the Control Panel are concurring with the system control of Windows, most of the description is here dispensed. The description of the control panel components relevant for operating the Touch Panel is to be found in the following: Set display Via Start > Settings > Control Panel > Display the dialog windows for the display properties opens. Here you may change the settings for the monitor options. For example you may adjust the brightness and contrast via the register Settings. Calibrate touch screen If your touch screen does not always react on a double click or recognizes the position of an entry not precisely, you may call the dialog Stylus via Start > Settings > Control Panel. In the register Double-Tap you may use the grid pattern to preset a double click velocity and test this on the symbol below. OK takes over the set value. The calibration of the touch screens happens via the register Calibration by following the instructions. Set Ethernet parameters The dialog field for pre-setting an Ethernet address is to be found at Start > Settings > Network and Dial-up Connections. The default setting is address assignment via DHCP. System properties (System) Here you receive information about the version of the current Windows operating system, the memory load and sharing (alterations here are not taken over into the registry) and about the copyright. The register Device Name allows you to change the device name that is e.g. shown during Ethernet communication. Note! All alterations made here are cleared after PowerOFF-PowerON. To store them permanently into the registry file you have to store them explicitly. For this, call Save Registry at Start > Programs > KuK Tools. Use [OK] to store the data in the registry file. HB160E - TP - RE_605-1B1E0 - Rev. 10/

38 Chapter 2 Deployment Touch Panel Manual VIPA HMI Set MPI parameters The dialog window where to configure the integrated MPI interface is to be found at Start > Settings > Control Panel > MPI Configuration. HSA Here you set the highest MPI address (highest station address). Within a MPI network the highest MPI address must be identical! TS With TS (this station) you set the local MPI address for the Touch Panel. Baud Rate Enter here the transfer velocity of your MPI net. The baud rate has to be identical for every MPI participant within the network. According to the Baud Rate the network parameters are set. Default Net Parameters It is recommended not to alter the Default Net Parameters that are set by the baud rate. Status The status of the MPI interface is monitored via Status as "Offline", "Online" or "Error". Note! Here made changes are also not saved after PowerOFF-PowerON. Save the data permanently in the current registry file via Save Registry at Start > Programs > KuK Tools HB160E - TP - RE_605-1B1E0 - Rev. 10/16

39 Manual VIPA HMI Chapter 2 Deployment Touch Panel Communication via ActiveSync Overview ActiveSync is a communication platform developed by Microsoft especially for mobile computers to synchronize data between a mobile device and a PC via USB res. Ethernet. Many developer tools res. SCADA projectengineering tools use ActiveSync for the data transfer. Before you may access the Touch Panel from the PC via ActiveSync you have to install it at the PC. ActiveSync is freeware and may be downloaded from Installation Download the ActiveSync from the Microsoft website and start the file MSASYNC.EXE. The following dialog window appears: Start the installation with [Next]. Choose an installation directory and click on [Next]. ActiveSync is installed. Establish connection After the installation the dialog window "establish connection" is opened. If your Touch Panel shall be available via Ethernet you have to install a pointto-point connection first. Start the search run with [Next]: HB160E - TP - RE_605-1B1E0 - Rev. 10/

40 Chapter 2 Deployment Touch Panel Manual VIPA HMI Install partnership for USB communication Now you may install a "partnership" via an USB connection with the following approach: Connect your Touch Panel via the "Device"-USB-B jack with your PC and turn on the Touch Panel. The USB device (Touch Panel) is recognized and the dialog window "new partnership" opens. Choose "yes" that you want to fix a partnership and push [Next]. In the now opening window, de-activate all synchronization settings and click on [Next]: [Finish] establishes the partnership. Now you may access the Touch Panel with ActiveSync via USB. Note! To keep the settings also after power on, you have to store them to the registry with START > Programs > KuK Tools > Save Registry HB160E - TP - RE_605-1B1E0 - Rev. 10/16

41 Manual VIPA HMI Chapter 2 Deployment Touch Panel Install partnership via Ethernet Please regard, Ethernet communication is only supported by ActiveSync up to Version 3.8. If your Touch Panel shall be available via Ethernet you have to install a partnership for USB communication first like shown above. Afterwards you may configure a partnership for Ethernet communication after the following approach: To enable the Touch Panel to be accessed via Ethernet you have to activate the option "enable network connection" in ActiveSync via File > Connection Settings: Disconnect the USB cable of the Touch Panel. Confirm the message that the device could not be found. Start the communication program required for ActiveSync at the Touch Panel via START > Programs > Communication > Act.Sync Netw and click on [Connect]. Now you may access the Touch Panel with ActiveSync via Ethernet. Note! To keep the settings also after power on, you have to store them to the registry with START > Programs > KuK Tools > Save. HB160E - TP - RE_605-1B1E0 - Rev. 10/

42 Chapter 2 Deployment Touch Panel Manual VIPA HMI Integrated Server Login data The Touch Panel has several integrated server that enable a remote maintenance within a network. Some servers only allow access by means of entering User name and Password. Per default the following login data are used: User name: wince Password: vipatp Change password You must not change the user name. But you may change the password via the registry. For this, start the editor via START > Programs > Registry Editor. The entry for the password is to be found at: HKEY_LOCAL_MACHINE/KUKINIT/DefaultPasswd Please remember to store the changes to the registry via START > Programs > KuK Tools before switching off. Overview Per default the following server are integrated: ftp server (activated) http server (activated) Telnet (activated) VNC (not activated) Phrases Phrases that are used in the description of the server: Client A client is an application that uses the service of a server within a network. For example, a web browser is a client because at every call of a website it sends a request to a web server and receives an answer. Server A server is an application that waits for the contact request of a client application and exchanges messages with it after contact start. This communication type is called Client-Server communication. Host Computer within a network where at least one server is running. Download Data transfer Server Client Upload Data transfer Client Server 2-22 HB160E - TP - RE_605-1B1E0 - Rev. 10/16

43 Manual VIPA HMI Chapter 2 Deployment Touch Panel ftp server By means of an ftp server data between client and server can be exchanged. Here you may copy, delete or create files and directories. For in the meanwhile an ftp client (Internet Explorer) is integrated in Windows, this is the easiest method for remote maintenance of the Touch Panel. Conditions for ftp access Depending on the ftp client your PC has to fulfill the following conditions for an ftp connection. If there are still problems with the ftp access ask your system administrator. Internet Explorer ftp access possible with version 5.5 or higher use passive ftp mode activate directory view for ftp sites For the adjustment choose in the Internet Explorer Options > Internet options, register "extended" in the area "Browsing and set the following settings: - activate: "activate directory view for ftp sites" - activate: "use passive ftp..." The settings are taken over when re-starting the Internet Explorer. Netscape Ftp access only possible with version 6.0 or higher, you need no further settings. HB160E - TP - RE_605-1B1E0 - Rev. 10/

44 Chapter 2 Deployment Touch Panel Manual VIPA HMI Establishing a ftp connection In the following the establishing of an ftp connection between a Windows based PC (here Windows 2000) with Internet Explorer as ftp client and your Touch Panel is shown. Connect your Touch Panel with the network where your PC is a member via an Ethernet cable. Switch on your Touch Panel. As soon as your Touch Panel is connected via Ethernet, you may monitor the IP address data via. After you ve confirmed the pre-settings, start your ftp client and enter the following text into the "address bar": ftp://wince:vipatp@ip-adresse The following window appears: Here you may execute the wanted file operations HB160E - TP - RE_605-1B1E0 - Rev. 10/16

45 Manual VIPA HMI Chapter 2 Deployment Touch Panel http server The Touch Panel has an integrated http server (web server) that allows depending on the access the administration of the Touch Panel res. of websites in the Touch Panel. The administrative access to the http server happens via Ethernet from the PC by setting the IP address of the Touch Panel with attached "Admin" type. By means of websites you may e.g. publish online documentations for a connected PC or go online with applications at the PC. Web admin As web admin you have access to all functions that are required for uploading and administrating of websites at the Touch Panel. Additionally you may set the access rights for user and create user groups. More detailed information about creating and administrating of websites at the Touch Panel is to be found in the online documentation of the web servers. The login as web admin requires the following steps: Start the web browser at your PC and enter the following into the address bar: IP address/webadmin Enter the following into the authentification: User name: wince Password: vipatp Remember to store your changes permanently in the registry via Start > Programs > KuK Tools > Save Registry! Sys admin Sys admin provides you with system administration rights for the administration of the Touch Panel. Here you may see system information and may administrate files, processes and registry entries. The login as sys admin requires the following steps: Start the web browser at your PC and enter the following into the address bar: IP address/sysadmin Enter the following into the authentification: User name: admin Password: vipatp Functions As sys admin you have access to the following functions: Group Area Description System Tools System Info System information about hardware, memory sharing and date/time. Processes Shows all running processes. Via "Kill" these can be terminated singularly res. be started with the field "Launch process". File Browser Drives File manager that offers all relevant functions for administration of files and directories. Registry Editor Registry key Registry editor for deleting, altering and creating of registry entries. HB160E - TP - RE_605-1B1E0 - Rev. 10/

46 Chapter 2 Deployment Touch Panel Manual VIPA HMI Telnet server Telnet is a text based client-server protocol on TCP level. By means of a Telnet client like e.g. the "MS-DOS console" in your Windows operating system you may execute text based all file remote functions at your Touch Panel like copy, delete and create files and directories. You may also start applications. Terminating an application is not possible. Establishing a Telnet connection The establishing of a Telnet connection is password protected and has the following approach: Start a Telnet client like for example "MS-DOS console" at your PC and enter the following into the address bar: telnet IP address When the connection is established, the Touch Panel asks for the user name and the password. Enter the following: Login: wince Password: vipatp (entry is hidden) After entering valid user data a command line for entries appears: By entering Exit res. closing the window you may terminate the Telnet connection at any time HB160E - TP - RE_605-1B1E0 - Rev. 10/16

47 Manual VIPA HMI Chapter 2 Deployment Touch Panel Commands After establishment of a Telnet connection the Touch Panel provides you with commands. A list of possible commands with a short description is available via the command help. By beginning with "help" before a command you receive help to this command. HB160E - TP - RE_605-1B1E0 - Rev. 10/

48 Chapter 2 Deployment Touch Panel Manual VIPA HMI VNC server The Touch Panel has an integrated VNC server (virtual network control) that allows the total control of the Touch Panel with a PC via network. For this, a window displays the current Touch Panel content for remote control. The operating happens via PC keyboard and mouse. Using VNC the context menu functions are available via the right mouse button. Condition for the VNC communication is that the VNC server is started at the Touch Panel and a VNC client at the PC. You may download a VNC client as Freeware from Internet. Note! Since with the VNC server all safety attitudes can be gone around, you should use these exclusively for start-up! For this reason the VNC server is on delivery deactivated. Establishing a VNC connection The VNC connection establishment has the following approach: Click on and open the "Windows" directory. You have to deactivate every option at View > Options to show the VNC server file. Start the VNC server by executing the file KUKVncSVR.exe. To show the server has been started the symbol appears in the task bar. You may also start the VNC server at the Touch Panel via a Telnet connection by entering the command kukvncsvr in the command console with an active Telnet connection. Now start the VNC client vncviewer.exe at your PC. Click on [Options] and de-activate the field "Emulate 3 Buttons..." like shown at Mouse. Enter the IP address of the Touch Panel at VNC server. With [OK] a VNC connection is established and the screen content of the Touch Panel is monitored within a window. Closing the VNC window terminates the VNC connection, the server keeps running HB160E - TP - RE_605-1B1E0 - Rev. 10/16

49 Manual VIPA HMI Chapter 2 Deployment Touch Panel Access to the network resources Overview The Touch Panel allows you to access shared resources in a Microsoft network like drives and printer. Here you may assign existing public directories or printer in the network to local directories or printer in the Touch Panel. Condition for this is that you login at the network with your user name and password. The assignment of a network resource happens in the Touch Panel via the command console "Command Prompt". Start the command console with START > Programs > Command Prompt. The access to the network resource happens with the commands Net view and Net use. List released resources Shared resources of a network PC can be listed with the command: \> net view PC-Name For example net view testserver lists all shared resources of the network PC "test server". To test the physical connection a PING to the IP address of the network PC may be executed if there are problems while contacting the network PC. \> net view testserver Shared resources on \\testserver: Share name Type Used as Comment Archive Disk (null) Process data KyoEDV Print (null) Kyocera FS-680 Printer Command completed successfully \> Connect net drive The connection of a local name at the Touch Panel with a shared drive of the network PC happens with the following approach: Enter the following in the command prompt: \> net use local_name \\network drive /user:user name Enter user name, password and where app. user group. After the successful login the following message appears: Successfully mapped to network name. The connected network drive is then available at the Touch Panel with the local name via My Device at Network. Example: Local_Name: data, network drive: testserver\archive, User name:gast Entry: \> net use data \\testserver\archive /user:gast The connected network drive is then available via \network\data at the Touch Panel. HB160E - TP - RE_605-1B1E0 - Rev. 10/

50 Chapter 2 Deployment Touch Panel Manual VIPA HMI Configure network printer The configuration of a network printer happens with the following approach: Enter the following into the command prompt: \> net use printer name network printer Example: Printer name: Printer, network printer: \\testserver\printer Entry: \> net use printer \\testserver\printer Enter user name, password and where app. user group. After the successful login the following message appears Successfully mapped to network printer The printer may now be accessed as "network\printer". Test print For example you may print the content of the current directory with \> dir > network\printer. List network connections The listing of all network connections of your Touch Panel happens via \> net use \> net use Connected resources: Status Local Name Remote Name Connected data \\testserver\archiv Connected printer \\testserver\printer Command completed successfully \> Terminate network connections You may terminate already assigned network resources via \> net use local_name /d Example: \> net use data /d deletes the network connection to the drive "archive" of "test server". Note! To keep the settings also after power on, you have to store them to the registry with START > Programs > KuK Tools > Save Registry HB160E - TP - RE_605-1B1E0 - Rev. 10/16

51 Manual VIPA HMI Chapter 2 Deployment Touch Panel Integration to WLAN network Overview By plugging a WLAN card there is the possibility to integrate your Touch Panel to a WLAN network. For this driver for the corresponding WLAN hardware are pre-installed. WLAN via SDIO card Please regard only SDIO WLAN cards are supported which drivers are preinstalled in the Touch Panel. In the Touch Panel driver exist for the following SDIO cards: Socketcom P300 Spectec SDW821 JustMobile Wireless LAN Card. Installation PowerON the Touch Panel. Plug the SDIO card the SDIO card is identified and a dialog window, which shows the available WLAN networks, is opened. Continue with "WLAN integration". WLAN via USB stick Please regard only WLAN-USB sticks are supported with the chip of the company Funkwerk inside! Installation PowerOFF the Touch Panel. Plug the WLAN USB stick to the USB-A interface. PowerON the Touch Panel the driver name is requested. Enter "prisma02" now your card is installed and activated. Note! To keep the settings also after PowerON, you have to store them to the registry with START > Programs > KuK Tools > Save Registry. WLAN integration Directly after installation a dialog window is shown. Here the available WLAN networks are displayed. Chose the corresponding network and click to [Connect]. At a safety-relevant network set the network parameters and enter the network key. If the parameters are correct the connection is established. HB160E - TP - RE_605-1B1E0 - Rev. 10/

52 Chapter 2 Deployment Touch Panel Manual VIPA HMI Automatically connect to WLAN If the Touch Panel should connect automatically to your WLAN network after startup, so the automatically connection is to be activated. For this open the register "Wireless Information" in the dialog window and click to the [Advanced...] button. The following window is shown: By activating of "Automatically connect to non-preferred networks" an automatically connection to the chosen network is established as soon as the network is available. Please do not forget to store the settings with the KuK Tools as shown above HB160E - TP - RE_605-1B1E0 - Rev. 10/16