Setup Guide for Express Line DVRs and NVRs

Transcription

1 Setup Guide XX Setup Guide for Express Line DVRs and NVRs Vicon Industries Inc. Tel: Fax: Toll Free: Hour Technical Support: VICON ( ) UK: 44/(0) Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose. Document Number: Product specifications subject to change without notice. Issued: 715 Copyright 2015 Vicon Industries Inc. All rights reserved.

2 Setup Express Series DVRs/NVRss 1 Connecting Express Line DVRs and NVRs to ViconNet This is a step-by-step procedure to add the Express Line DVRs and NVRs for use with the ViconNet Video Management System. It assumes an understanding of ViconNet and the DVRs/NVRs. Refer to the ViconNet and camera manuals for detailed information. The DVR/NVR is added to the network and then connected to the ViconNet system.

3 2 Setup Express Series DVRs/NVRs Setting the DVR/NVR Network Address Prior to adding the Express DVRs and HDExpress NVRs to ViconNet, it must be configured to a valid network address on the Express unit itself. 1. From SYSTEM SETUP, go to the NETWORK screen and select IP SETUP. 2. Specify each item of the network settings, IP address, gateway, subnet mask, primary and secondary DNS server. If DHCP is used, set the IP address of the unit to a Dynamic IP; when this is checked, the sub items of IP address, gateway, subnet mask, primary and secondary DNS server will fill in automatically. 3. Once the device is on the network, it can be added to ViconNet as explained below.

4 Setup Express Series DVRs/NVRss 3 Adding Express DVRs/NVRs to the Nucleus The Express device must be added to the Nucleus of the system to be recognized on the ViconNet site list. These devices do not require a license, but do not automatically show up on the site list and must be added to the ViconNet system. Refer to the Express manual for details on installation and setup of the camera. Note: These devices do not need to be registered and only need to be added once in the Nucleus for the entire system. The device name is determined by the name configured when adding the device and not by the host name. This is the name that will show up in the VIconNet site list. 1. From the ViconNet Main window, click. The Setup Site Selection window is displayed. 2. Select the Nucleus for which you want to configure the camera and click. The System Settings window is displayed. 3. From the System Settings window, select the button. 4. Click on the Open Standard Camera settings screen. 5. The devices that are detected on the network will be listed in the Available Cameras On Net drop down list. Alternatively, you can

5 4 Setup Express Series DVRs/NVRs Note: add the device name, IP and credentials in the designated fields. A message will display to add a User Name and Password for each detected device. The User Name and Password for the device are its credentials in its UI/browser. It is recommended that the user be administrator level to be able to access all camera features. After being named, the device can be activated. To edit details, click on the button. The Camera Details area will become enabled. Devices will only be detected and listed if they are on the same LAN as the PC. Devices that are not on the LAN have to be added manually by entering their details. 1. Enter a Name for this device and select IP or DNS. 2. The format is set from the camera s Video Settings screen. Select the same format, H.264 or M-JPEG. 3. The Port Number will default to Enter a User Name and Password for this device. It is recommended that the user be administrator level to be able to access all the features. If you want to specify a site where the device is recorded (instead of automatic recording search), select it from the dropdown Primary recording site list; this is an optional setting. Default User and Password are ADMIN and There is a checkbox to Enable Edge playback. This allows a device to be played back directly from the device itself, not from ViconNet. Note that for the Vicon Express devices, ViconNet recognizes it as an Edge device and the fields remain grayed out but Edge playback is enabled. You can test the playback address by clicking. When Edge playback is enabled, the camera playback interface will display and playback is viewed from there. See screen below. An Express device can record both on ViconNet and internally. 6. Click Save to save the settings. An Undo button is provided.

6 Setup Express Series DVRs/NVRss 5 7. Click the button for a direct link to the browser for that device. Click Save and Close. 8. If required, you can configure the primary ViconNet recording device; otherwise, ViconNet will search for it automatically (this is sometimes required for recording sites with network delay). 9. Click on the button. This opens a screen that allows setting up authorization for Live View, Playback and PTZ actions by selecting ( ) or deselecting ( ) the appropriate categories, as required. If all cameras are to have the same authorizations, check Apply to all cameras box to avoid setting up each camera individually. When this procedure is complete, the camera will appear on the ViconNet site list and there will be access to the video.

7 Vicon Industries Inc. For office locations, visit the website: