UMAC Guide PUB NE 60th Way Vancouver, WA Voice Fax
|
|
- Leon Ball
- 6 years ago
- Views:
Transcription
1 UMAC Guide PUB NE 60th Way Vancouver, WA Voice Fax
2 Applied Motion Systems, Inc. All rights reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means, whether electronic, mechanical, or otherwise without the prior written permission of Applied Motion Systems, Inc. No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law, no liability (including liability to any person by reason of negligence) will be accepted by Applied Motion Systems, Inc., its subsidiaries, or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document. Applied Motion Systems, Inc. reserves the right to change details in this publication without notice. Windows is a trademark and Microsoft, MS-DOS, and Windows NT are registered trademarks of Microsoft Corporation. Other product and company names herein may be the trademarks of their respective owners. Applied Motion Systems, Inc NE 60th Way Vancouver, WA Voice (360) Fax (360) Table 1 Revision History Revision Date Description February 2007 Initial release March 2007 Updated screenshots March 2007 Moved Download the Compiled Code before Download and Restore the Configuration File and minor editorial changes throughout April 2007 Updated the Downloading and Restoring a Configuration procedure October 2007 Added the About the PMAC section November 2007 Added /Pro2 terminology throughout the document. Revised the Establishing Communications section. Added the Configuring a Spare ControlNet UMAC Board section. UMAC Guide Page 2 of 40 PUB
3 Table 1 Revision History (Continued) Revision Date Description April 2009 Added the Setting or Changing a UMAC IP Address section (only for UMACs with Ethernet networking capability). UMAC Guide Page 3 of 40 PUB
4 Contents 1 Introduction Using This Guide Our Service Ethic Typographic Conventions PEWin32PRO/PRO2 and Your UMAC Controller Required Tools Cautions Summary of Uploading and Saving a Configuration Summary of Downloading and Restoring a Configuration Setting or Changing a UMAC IP Address Establishing Communications Before You Begin Select and Test the Desired PMAC Device PEWin32Pro/Pro2 Functions Uploading and Saving a Configuration Downloading and Restoring a Configuration Prepare the Processor Download the Compiled Code Download and Restore the Configuration File Verify the Downloads Controller Operation and Programming Details Configuring a Spare ControlNet UMAC Board Technical Support UMAC Guide Page 4 of 40 PUB
5 1 Introduction Thank you for purchasing an Applied Motion Systems machine control and drive system. 1.1 Using This Guide In this guide, we describe how to reconfigure a UMAC controller. We assume that users of this manual are system technicians, engineers, and/or managers. We assume you are trained on safety standards. Throughout this guide we refer to you as the operator, technician, user, or manager of the drive or control system. We are the designers of the system at Applied Motion Systems, Inc. 1.2 Our Service Ethic If you have questions about this system that are not answered in this guide, please contact us at (360) We will do our best to answer your questions quickly and accurately. If you have suggestions for system improvement or a new feature, please let us know. We will make every effort to put your idea to work on your machine. Thank you again for selecting AMS. We look forward to serving you. 1.3 Typographic Conventions The following table explains the typographic conventions used throughout this guide. Table 2 Typographic Conventions Convention To indicate a selection sequence, directories and subdirectories are boldfaced and separated by a pipe ( ). Example Go to Control Shear Control. In this example, first select the Control directory, followed by the Shear Control select button on the Control directory page. Hyperlinks are blue and underlined. See Appendix D on page 76. UMAC Guide Page 5 of 40 PUB
6 Table 2 Typographic Conventions (Continued) Convention Status messages and control and select buttons are capitalized. Placeholders are italicized. Example Selecting START RESOLVER TEST enables the selected motor and starts the resolver test. The file naming convention for event files is evyymmdd.evt. For example, a file named ev evt is the event log for February 14, Select and open the configuration file for your shop (Your_Shopname.p7k). UMAC Guide Page 6 of 40 PUB
7 2 PEWin32PRO/PRO2 and Your UMAC Controller The UMAC and PMAC are both high-performance motion controllers. Your system may have either controller, or both. We have provided a description of both controllers in this section for your reference. However, we use the terms UMAC and PMAC interchangeably in this guide unless otherwise noted. The process for configuring either motion controller is identical. AMS has made every effort to minimize the possibility of corruption of the application software and parameter settings stored in the UMAC. In the event that this does happen, or a hardware failure of the main UMAC CPU board occurs, you must download a complete backup configuration to your spare UMAC CPU board. To do this, you can use any Windows-compatible PC loaded with the UMAC Executive software, PEWin32Pro or PEWin32Pro2. Note: PEWin32Pro and PEWin32Pro2 are the two latest executive version releases from Delta Tau. Both are similar in look and functionality, but where differences occur, this guide provides instructions both versions. Note: The executive software can also be used to upload the current configuration from the UMAC CPU for archival purposes. If modifications are ever made to the software running in the UMAC, it is important to save the changes in a backup configuration file. Then, should a spare UMAC CPU board need to be restored, an accurate configuration is available to download. In this section, we provide instructions for: PEWin32Pro/Pro2 Functions on page 20 Uploading and Saving a Configuration on page 21 Downloading and Restoring a Configuration on page 23 In addition, we have provided abbreviated versions of the procedures for Uploading/Saving a Configuration and Downloading/Restoring a Configuration on page 9. About the UMAC The UMAC is a high-performance motion controller that is capable of managing up to 32 drives. The UMAC resides in a 3U rack and is often linked to a supervisory PLC via an industrial network such as ControlNet, Ethernet, or a local ISA bus to allow high-speed data transfer. This ongoing transfer of information allows control and adjustment of various parameters that can be changed through the HMI. The UMAC runs control software/code much like a PLC. Along with this program code, the UMAC also has memory definitions, axis-specific parameters, and set-up variables, which are also similar in structure to a PLC. UMAC Guide Page 7 of 40 PUB
8 About the PMAC The PMAC is a high-performance motion controller that is capable of managing up to 8 drives. The PMAC resides in a VME rack along with the Allen-Bradley V30B PLC processor. The Allen-Bradley reads and writes blocks of data to and from the PMAC, and to and from the SoftPLC in the control cabinet. This ongoing transfer of data allows high-speed control and adjustment of various parameters that can be changed via the HMI. The PMAC runs control software/code much like a PLC. Along with this program code, the PMAC also has memory definitions, drive specific parameters, setup variables, etc., which are similar in structure to a PLC. 2.1 Required Tools To complete the procedures in this section, you will need the following: A UMAC controller A Windows-compatible PC The PEWin32Pro or PEWin32Pro2 software This software is available for purchase from AMS. Alternatively, you can download a free trial version from Delta Tau s Web site ( A serial or Ethernet cable to connect your PC to the controller Note: If you are performing this procedure on a spare controller, you must install it in a rack with an identical hardware setup as is used in your system Cautions Do not attempt this operation while any motors in the system are running. When bringing a spare UMAC into service for the first time, verify all the jumpers are set correctly to ensure that the hardware is properly configured to your specific drive system (see drawing set shipped with your system for jumper details). When in doubt, compare the new card to the old one. Failure to comply with this instruction may cause severe damage to the UMAC card as well as any and all connected electronics and equipment. UMAC Guide Page 8 of 40 PUB
9 2.2 Summary of Uploading and Saving a Configuration Following is an abbreviated version of the process of uploading and saving a configuration to a backup file. For a detailed version of this process, see Uploading and Saving a Configuration on page Establish communications. Use PEWin32Pro/Pro2 to establish either serial or Ethernet communications with the UMAC. The software may take several seconds to find your UMAC. 2. Stop all programs. From the terminal window, type I5=0 and then Enter to stop all programs. 3. Kill the axes. Type CTRL+K to kill all running axes. 4. Select Backup Upload Configuration from the PEWin32Pro/Pro2 toolbar. 5. Configure the backup options as shown in Figure 12 on page Save a global configuration. Choose the location and filename for the configuration file (ex: Name_Shop#_YYMMDD.CFG where YYMMDD is the file creation date, e.g., denotes the 22nd of June, 2007). Select SAVE and wait for the upload operation to complete. 7. Close the Backup Configuration window by selecting DONE. 8. Re-enable the programs. In the terminal window, type I5=3 [Enter] to re-enable PLC and PLCC programs. 2.3 Summary of Downloading and Restoring a Configuration Following is an abbreviated version of the process of downloading and restoring a configuration to a UMAC CPU. For a detailed version of this process, see Downloading and Restoring a Configuration on page Establish communications. Use PEWin32Pro/Pro2 to establish either serial or Ethernet communications with the UMAC. The software may take several seconds to find your UMAC. 2. Stop programs. From the terminal window, type I5=0 and then Enter to stop all programs. 3. Kill the axes. Type CTRL+K to kill all running axes. 4. Clear the UMAC memory. Type $$$*** [Enter] to clear the UMAC memory. 5. Set the I46 value. Check the value of I46 in the backup (.cfg) file and set it in the UMAC. UMAC Guide Page 9 of 40 PUB
10 6. Save the I46 value. Type SAVE [Enter] to save the I46 value. 7. Activate the I46 value. Reset the system. Type $$$ [Enter] to enable the new I46 setting. 8. Select File Download File from the PEWin32Pro/Pro2 toolbar. 9. Download the compiled code. Choose the UMAC compiled code file to download (ex: Name_Shop#_PLCC_YYMMDD.PMC). Check for errors and warnings. 10. Select Backup Restore Configuration from the PEWin32Pro menu. 11. Download the configuration. Choose the UMAC configuration file to restore (ex: Name_Shop#_YYMMDD.CFG). Check for errors and warnings. 12. Enable the programs. In the terminal window, type I5=3 [Enter] to enable the PLC and PLCC programs. 13. Save the programs. Type SAVE [Enter] to save the program to flash memory. 14. Reset the system. Type $$$ [Enter] to reset the system. 2.4 Setting or Changing a UMAC IP Address This section explains how to configure or change an IP address for a UMAC so that you can connect to it via your Ethernet network. This option is available only for UMACs that have Ethernet networking capability. If you want to simply connect with an existing UMAC via a serial or Ethernet connection, you may skip this section and go to Establishing Communications on page 13. You would configure or change an IP address for a UMAC only when commissioning a new UMAC or when changing the address of an existing UMAC whose IP address has already been configured. CAUTION To avoid potential conflicts with the default IP address used by the UMAC and other devices/addresses on the Ethernet network, set up the UMAC IP address before you connect the UMAC to the network. 1. Using a USB cable, connect your computer to the USB port on the front of the UMAC. Note: All other communication activies with the UMAC require you to connect with it via an Ethernet connection from your computer. However, because the UMAC s IP address is stored in a separate flash memory location, you must set the UMAC s IP address using a USB connection, not an Ethernet connection. UMAC Guide Page 10 of 40 PUB
11 2. On your computer, launch the Ethernet configuration utility Configure Ethernet 100 BaseT.exe. This program is included with the PEWin32Pro2 software package and is typically located in the Windows Start menu under All Programs PMAC Executive Pro2 Suite Delta Tau Common. This software is available for purchase from AMS. Alternatively, you can download a free trial version from Delta Tau s Web site ( After you have launched the utility, the following window will be displayed on your computer: Figure 1 Ethernet Configuration Utility 3. Next to the Store IP button, type in the desired IP address. Then press the Store IP button. If you do not know the correct IP address to use, consult your IT department. A pop-up window confirms that you have successfully written the new IP address to the EEPROM, and prompts you to set up the registry on your computer. Select Yes to set up the registry. UMAC Guide Page 11 of 40 PUB
12 4. You can set up one or multiple IP address registry entries on your computer depending on the number of UMACs you will be communicating with from your computer. If this is the only UMAC in your plant, AMS recommends entering a value of 0 in the Ethernet Card Instance pop-up window (Figure 2). If you are or will be setting up for more than one UMAC (for example, if you have several UMACs dispersed throughout your plant), enter any unused value from 0 to 7 in the Ethernet Card Instance pop-up window (Figure 2). The instance used is arbitrary, but should be unique per UMAC IP address to be registered on your computer. Figure 2 Ethernet Card Instance 5. Next select the TCP radial button in the Protocol frame of the Ethernet Configuration Utility window. Again, you will need to set the Ethernet Card Instance. Use the same instance as entered when setting the IP address in step Make sure the Gateway IP and Gateway Masks are NOT set to If required, change each of them to and then press the Gateway IP and Gateway Mask buttons. 7. Close the Ethernet Configuration Utility, remove the USB cable, and cycle power to the UMAC. The new IP address and TCP mode have now been successfully set for the UMAC. In addition, you have successfully recorded the IP address and Ethernet instance in the Windows Registry of your computer. To verify the new IP address: 1. Make sure your computer and the UMAC are connected to each other directly with an Ethernet cable or through a switch. 2. Launch the Run utility from your Windows Start menu and type cmd into the Open: box. UMAC Guide Page 12 of 40 PUB
13 3. From the command prompt, type ping <your_ip_address_here>, for example: ping If the IP address is working, you will receive a reply from it. If the IP address is not working, your ping will be unsuccessful and time out. In this case, verify that you have correctly performed all of the steps in the Setting or Changing a UMAC IP Address procedure. 2.5 Establishing Communications If your computer has been previously set up to communicate with the UMAC, those settings are automatically saved. When you subsequently restart the PEWin32Pro or PEWin32Pro2 software, it should begin communicating with the UMAC as it had before. This section is intended for users who have just installed the software or encounter difficulties in getting online with the controller. Depending on your specific system and the UMAC CPU used, you may have the option of communicating via serial and/or Ethernet protocols. Ethernet is faster and should be used if it is an option. These instructions detail setting up both the serial and Ethernet communication methods; disregard comments if they do not apply to the connection type you will be using. Install the PEWin32Pro or PEWin32Pro2 software on your computer. For additional details see the Required Tools on page 8 section of this guide Before You Begin 1. Connect your computer to the UMAC using any of the following cables: Ethernet Use an Ethernet cable with RJ-45 connectors (AMS part number CAT5E-S, supplied with your system). You can plug directly into the front of the UMAC or through an Ethernet switch if it was provided with your system. Serial Use a 10-pin DB-9 adapter cable (AMS part number CBL-0005), which may already be attached, with a straight-through serial cable (AMS part number CV-20106, supplied with your system). UMAC Guide Page 13 of 40 PUB
14 2. Ensure your computer port settings are correct. Ethernet To communicate with the UMAC over Ethernet, you must ensure your PC IP address and subnet mask are set appropriately. It is always a good idea to open a command window and ping the address of the UMAC to ensure cabling and address issues are correct. Serial Ensure that RSLinx is not active. RSLinx is often set to use one of your computer s RS-232 COM ports and will tie it up, preventing the PEWin32Pro/Pro2 software from accessing the port and getting online with the UMAC Select and Test the Desired PMAC Device 1. Open the PEWin32Pro/Pro2 software. Go to Setup General Setup and Options as shown in the following figure. Figure 3 PEWin32Pro Setup Menu 2. Under the Default Device tab, click the Select button as shown in Figure 4. This opens the UMAC Devices window as shown in Figure 5. UMAC Guide Page 14 of 40 PUB
15 Figure 4 PEWin32Pro General Setup and Options Dialog Box Figure 5 PEWin32Pro Device Select Dialog Box 3. If the desired serial or Ethernet device is listed, select it and skip to Test the Device (step 6). Otherwise, if this is your first time running the program, there will not be any devices listed in the list box (as there are in Figure 5); you have not yet added any to your operating system so you will need to insert them. In the PMAC Devices list box, highlight any unassigned NA device numbers and then click Insert. 4. In the Available PMAC Devices list box, select the one you want to add and click OK. UMAC Guide Page 15 of 40 PUB
16 Figure 6 PEWin32Pro Available Devices Dialog Box For serial connections with PEWin32Pro1 If you need to insert a serial device, you must first install a driver before the serial device will become available to insert. Refer to the PEWin32Pro Help documentation or consult AMS for details with installing the serial driver. For Ethernet connections with PEWin32Pro1 Ethernet devices require a special configuration program to be run before they show up as available devices in PEWin32Pro1. If your devices do not show up in the Available Devices list, refer to Setting or Changing a UMAC IP Address on page 10. Note that in this case, you do not need to connect the UMAC to your computer with a USB cable because setting up the registry on your computer does not require you to be connected to the UMAC; you just need to run the utility and set up the UMAC address in the registry. For Ethernet connections with PEWin32Pro2 If any of the IP addresses are not available for insertion due to this being a new installation, you can define the addresses on-the-fly now by pressing the New button, selecting Ethernet (ETH) in the following window, and then entering the card instance (Enumeration) and its IP address. If this is the only UMAC in your plant, AMS recommends entering a value of 0 for the Enumeration. If you are or will be setting up for more than one UMAC (for example, if you have several UMACs dispersed throughout your plant), enter any unused value from 0 to 7 in the Enumeration box. The instance used is arbitrary, but should be unique per UMAC IP address to be registered on your computer. UMAC Guide Page 16 of 40 PUB
17 Figure 7 New IP Address 5. If using a serial device, you need to set its baud rate to match the baud rate of the UMAC CPU. Highlight the serial PMAC device and click the Properties button. On the Configure UMAC Serial Port dialog box that appears, select the appropriate baud rate (38400 is most common, followed by 19200) and then click OK. UMAC Guide Page 17 of 40 PUB
18 Figure 8 PEWin32Pro Device Properties Dialog Box 6. After you have inserted and highlighted the desired PMAC device, click the Test button to poll communications. The program will pause momentarily while loading the driver. Figure 9 Poll Communications Test Window UMAC Guide Page 18 of 40 PUB
19 If communication is successfully established, a dialog box informs you: The UMAC device was successfully detected. If communication is not established, a dialog box informs you: Unable to establish communications. If this occurs, ensure that you have the correct cable connected to the system and that your communications settings match. You may also need to ensure that there are no other serial drivers such as RSLinx interfering with the use of your RS-232 port. If you are unable to resolve this problem, contact AMS for technical support. 7. Click OK until all open configuration windows are closed. 8. If any terminal or position windows were previously open, you need to force them to use the communications device you just set up and tested. Go to Setup Force All Windows to Device Number to bring up the PMAC devices dialog box again. Figure 10 Forcing All Windows to Device Number 9. Select the device you wish all open windows to use and click OK. Your computer is now configured to communicate with the UMAC and initial communications have been established. To continue using the PEWin32Pro/Pro2 software for online functions with the UMAC, see PEWin32Pro/Pro2 Functions on page 20. UMAC Guide Page 19 of 40 PUB
20 2.6 PEWin32Pro/Pro2 Functions After you have successfully connected your computer and established communications with the controller, you can do the following using the PEWin32Pro/Pro2 software: Type any valid UMAC online command or query by going to View Terminal. View the positions of each of the axes by going to View Position. Continuously monitor any variables by going to View Watch Window. Download and restore a configuration to a UMAC CPU (see Downloading and Restoring a Configuration on page 23). Upload and save a configuration to a backup file (see Uploading and Saving a Configuration on page 21). The following figure shows the Terminal window open. If the Terminal Window or any other window is maximized, you will not be able to see the other windows easily. If this occurs, click on the Window Restore button at the top right corner of the screen; do not confuse this button with the Application restore button, which is top-most in the upper right-hand corner. Figure 11 PEWin32Pro with the Terminal Window Open UMAC Guide Page 20 of 40 PUB
21 2.7 Uploading and Saving a Configuration Uploading and saving a UMAC configuration to a backup file ensures that a UMAC can be restored to a proper running state at any time in the future. To save the UMAC s configuration to a backup file: 1. From the PEWin32Pro/Pro2 toolbar, select View Terminal. 2. In the terminal window, type I5=0 and then Enter. This disables the code running on the UMAC. 3. Type CTRL+K to kill all running axes. 4. From the toolbar, select Backup Upload Configuration. This brings up a dialog box with an assortment of check boxes used to determine what will be added to the configuration file. Set up the check boxes as follows, then click OK. Figure 12 PEWin32Pro/Pro2 Backup Configuration Options Dialog Box UMAC Guide Page 21 of 40 PUB
22 5. After clicking OK, you are prompted for a filename. Select (or create) the folder and filename on the hard drive and click Save. The file type for the backup must be.cfg. This is the default setting, so you do not need to enter the CFG file extension in the Save as type box. Figure 13 PEWin32Pro Save Configuration Filename Select Dialog Box 6. If you are using a serial connection, you are asked if you want to use check sum communications. Select Yes. The software then begins to upload the configuration file from the UMAC. A progress bar appears at the bottom of the window. The upload may take a few minutes. 7. After the upload is complete, in the Backup Configuration window, click Done. 8. When the software indicates the upload is complete, you need to set I5 equal to three in order to start the PLCs running again. In the terminal window, type I5=3 and then Enter. Note: This procedure does not save the compiled programs (PLCC). The PLCC programs should only be downloaded from PEWin32Pro/Pro2 and not saved in a backup file. This is because the compiled code is firmware-dependent and can only be loaded into a UMAC with the same firmware as it was backed up with. Uploading all code except the PLCC offers the most flexibility in restoration if a new UMAC processor has different firmware than the processor it is replacing. The downloadable PLCC source code supplied by the AMS engineer at startup should be kept in a safe place. UMAC Guide Page 22 of 40 PUB
23 2.8 Downloading and Restoring a Configuration Downloading and restoring a software configuration to a UMAC CPU board is a four-part process: 1. Prepare the processor (see page 23). 2. Download the compiled code (see page 27). 3. Download and restore the configuration file (including uncompiled code) (see page 29). 4. Verify the downloads (see page 33). Each of these steps is explained in detail in the following sections Prepare the Processor To prepare the processor, you must first clear the CPU memory and restore the card to factory defaults. This ensures that any previously running code is cleared and begins the restore process from a consistent starting point. Following the memory reset, you need to set any UMAC configurations that only take affect at power-up. Here we address only the location for storing P & Q variables. Each type or both can be stored in either battery-backed or RAM memory. The value of parameter I46 defines how they are stored. This value needs to be set and saved in the processor before loading configuration files. To set and save the I46 value: UMAC Guide Page 23 of 40 PUB
24 1. Open the backup configuration file with a text editor and note the value assigned to parameter I46, then close the file. (The value for parameter I46 should be a 0, 1, 2, or 3). Figure 14 Backup File Opened in a Text Editor 2. Establish communications with the UMAC. (For instructions, see PEWin32Pro/Pro2 Functions on page 20). 3. From the PEWin32Pro/Pro2 toolbar, select View Terminal. 4. In the terminal window, type I5=0 and then Enter. This disables the code running in the UMAC. 5. In the terminal window, type CTRL+K. This kills any currently executing motion programs. UMAC Guide Page 24 of 40 PUB
25 6. In the terminal window type $$$*** [Enter]. This clears the UMAC memory of all programs and definitions, and sets the processor back to factory defaults. The following figure shows the terminal window after clearing the UMAC memory. Figure 15 Terminal Window after Clearing the UMAC Memory 7. In the terminal window, type I46 [Enter] to check the current value of I46. If the value of I46 is different than you noted in Step 1, then set the value to the one from Step 1 by typing I46=n [Enter], where n is the value you noted in Step In the terminal window, type SAVE [Enter] to save the updated values to flash memory. UMAC Guide Page 25 of 40 PUB
26 9. In the terminal window, type $$$ [Enter]. This resets the UMAC and enables the new settings. The following figure shows the terminal window after setting up I46. Figure 16 Terminal Window after Setting Up I To continue, proceed to the next step in Download and Restore the Configuration File. UMAC Guide Page 26 of 40 PUB
27 2.8.2 Download the Compiled Code After you have prepared the processor, you must download the compiled code. To do so: 1. In the PEWin32Pro/Pro2 software, go to File Download File as shown in the following figure. Figure 17 PEWin32Pro File Menu UMAC Guide Page 27 of 40 PUB
28 2. In the Download File dialog box, select the necessary compiled code file (e.g., Name_Shop#_PLCC_YYMMDD.PMC) as shown in the following figure and click Open. If you are using a serial connection, you are asked if you want to use check sum communications. Select Yes. The software begins downloading the file to the UMAC card. A progress bar appears at the bottom of the window. The download may take a few minutes. Figure 18 Download File Dialog Box 3. When the software indicates the download is complete, check the status of the download in the status Results window at the bottom of PEWin32Pro/Pro2. It should read 0 warnings, 0 errors. Note: If the results show anything but 0 warnings and 0 errors, contact technical support at Applied Motion Systems at (360) Figure 19 Results Window UMAC Guide Page 28 of 40 PUB
29 4. The compiled code is now downloaded. To continue, proceed to the Download and Restore the Configuration File section Download and Restore the Configuration File After you have downloaded the compiled code, you must restore the configuration file. The UMAC Executive Program s Restore Configuration function manages this task. Make sure you copy the backup file to be used to your hard drive before using the Restore Configuration function. 1. In the terminal window, type I5=0 and then Enter. This disables the code running on the UMAC. 2. From the toolbar, select Backup Restore Configuration. This causes the software to open a window where you can select the required *.cfg backup file of your machine s setup parameters and software. This file contains all the information required to run the drive system and should be located on the hard drive, not a floppy drive. UMAC Guide Page 29 of 40 PUB
30 Figure 20 PEWin32Pro Backup Menu UMAC Guide Page 30 of 40 PUB
31 3. In the Download File box, select the file that you wish to use to restore the card (if your system does not have a mouse, use the Tab and arrow keys to select the file). The file you select should be the last backup file created from a known working system. If any changes to the operating software have been made since this backup was created, you must reload the changes after you have completed the restore process. Figure 21 Select Restore File Dialog Box (Download File) 4. After you have highlighted the appropriate backup file, press Enter. If you are using a serial connection, you are asked if you want to use check sum communications. Select Yes. The software begins restoring the file to the UMAC card. The downloading process may take several minutes. 5. When the software indicates the download is complete, check the status of the download in the status Results window at the bottom of PEWin32Pro/Pro2. It should read 0 warnings, 0 errors. Note: If the results show anything but 0 warnings and 0 errors, contact technical support at Applied Motion Systems at (360) UMAC Guide Page 31 of 40 PUB
32 Figure 22 Results Window 6. Type I5=3 and then Enter in the terminal window. This starts the PLCs running again. 7. In the terminal window, type SAVE [Enter]. This saves the new configuration to the flash memory in the UMAC and indicates when the operation is finished. 8. Restart the software by resetting the card. In the terminal window, type $$$ [Enter], or cycle power on the system. This ensures that the proper initialization sequence occurs. 9. Now that you have installed both of the required files to restore the UMAC, and the card has been saved and reset, ensure that the downloaded code is running properly. To continue, proceed to the final step of Downloading and Restoring a Configuration on page 23. UMAC Guide Page 32 of 40 PUB
33 2.8.4 Verify the Downloads This procedure includes checking the status of the PLC and PLCC program files to verify they were downloaded correctly and are active. 1. In the PEWin32Pro/Pro2 software, go to View Program/PLC Status (and Upload) to check the status of the uncompiled code. There should be a number of PLC and motion programs listed. In most cases, all will be active except PLC1. (We recommend making a list of the active ones on your project when the system is running correctly. That way you can compare them to the current code after a restore procedure). Figure 23 Upload Programs (Motion and PLC) Dialog Box UMAC Guide Page 33 of 40 PUB
34 2. To check the status of your compiled code, go to View PLCC Status. This brings up a window that shows the status of each of the compiled code modules. All of the PLCCs should be listed as active (not necessarily the numbers shown in the following figure). Figure 24 PLCC Program Status Dialog Box 3. There are a number of parameters associated with machine operation that may have changed since the backup was made (e.g., production rates). In the HMI, verify machine setup before putting the machine back into production. The UMAC processor is now set up correctly for proper system operation. 3 Controller Operation and Programming Details For detailed information about the PEWin32Pro software and the controller hardware, refer to the Delta Tau documentation CD included with your system. UMAC Guide Page 34 of 40 PUB
35 4 Configuring a Spare ControlNet UMAC Board Many AMS control systems implement the UMAC motion controller coupled with a PLC via a ControlNet network. The UMAC manages all the lower level motor control and precise synchronization operations, while the PLC handles the supervisory functions of start and stop signals, interfacing with the HMI, and general digital I/O manipulations. The ControlNet link is a vital interface between the UMAC and PLC controllers and is required for certain systems to operate. The UMAC interfaces to the ControlNet network via an ACC-72E ControlNet slave accessory board in the UMAC rack. This card relays information back and forth between the PLC on the ControlNet network and the UMAC CPU board across the UMAC backplane. In order for the data transfer to occur, the ACC-72E must have its own ControlNet configuration downloaded to it. This setup only needs to be downloaded once and is done at system commissioning by the AMS startup engineer. However, if the ACC-72E board were to fail and you replaced it with a spare, the new board would need to be configured before the system could become operational. To set up a new ACC-72E board: 1. Install the SyCon configuration setup/download program if it is not already on your computer. This software is provided with the AMS system documentation on the ACC-72E CD from Delta Tau. 2. Run the SyCon software and go to File Open to open the ControlNet configuration file for the ACC-72E. This file was provided with the system backup code at commissioning and has a.cn file extension (e.g., Sycon UMAC GW Config 215.cn ). UMAC Guide Page 35 of 40 PUB
36 Figure 25 Opening the ControlNet File from SyCon 3. Double-click on the ControlNet icon on the left side of the screen to bring up the ControlNet Device Configuration window as shown in Figure 26. UMAC Guide Page 36 of 40 PUB
37 Figure 26 ControlNet Device Configuration Window 4. Make sure all the settings match the settings shown in Figure 26. The MAC ID is the node of the card on the ControlNet. Input and Output lengths should be left at 215 words each, the maximum possible for the ACC-72E. 5. Attach a 9-pin straight-through serial cable between your laptop serial port and the front of the ACC-72E card. Your specific UMAC rack may or may not contain the other cards shown in Figure 27. UMAC Guide Page 37 of 40 PUB
38 Figure 27 Serial Port on the ACC-72E Card 6. Now download the configuration file to the ACC-72E by selecting Online Download. Choose the CIF Serial Driver when prompted, then click OK. Figure 28 Driver Select Window Note: Make sure that RSLinx is not running in the background. It often uses the same PC COM port and will prevent the SyCon software from using the port to download the configuration. 7. When the Device Assignment CIF Serial Driver window opens, select the Connect COM button to the COM port that the serial cable is connected to (typically COM 1). UMAC Guide Page 38 of 40 PUB
39 Check the associated box on the left and press OK. This should open communications with the ACC-72E and begin the configuration file download. If the communications don t start and you get a -51 error, you may have a cross-over or null modem serial cable attached. Figure 29 Device Assignment CIF Serial Driver Window 8. A Download window will appear with a progress bar. Wait for the complete configuration to be transferred, then close SyCon and remove the serial cable. This completes the setup of the ACC-72E. Figure 30 Download Progress Bar UMAC Guide Page 39 of 40 PUB
40 Technical Support We make every effort to ensure that your system works properly. If you experience a problem with your system, please do not hesitate to contact us at (360) at any time of day or night. If you are calling after business hours, dial extension 240 to be connected to our 24-hour emergency voice mailbox. Please be sure to leave the following information in your message: Your name Plant location and line or shop number Phone number Description of AMS equipment requiring technical support Brief description of the problem For calls received after business hours, the on-duty dispatcher will return your call within fifteen minutes and contact the engineer best capable of handling your issue. The engineer will then contact you directly. The emergency mailbox automatically pages the on-duty dispatcher and a backup dispatcher every five minutes until someone checks the message. In the rare event that no one returns your call within 30 minutes, please call the emergency dispatcher directly at (360) Thank you for choosing Applied Motion Systems. We appreciate your business. UMAC Guide Page 40 of 40 PUB
UMAC Guide PUB NE 60th Way Vancouver, WA Voice Fax
UMAC Guide PUB-0001-06 12000 NE 60th Way Vancouver, WA 98682 Voice 360.253.4810 Fax 360.253.4818 www.appliedmotionsystems.com 2007 Applied Motion Systems, Inc. All rights reserved. No part of this document
More informationCT Unidrive SP Guide PUB NE 60th Way Vancouver, WA Voice (360) Fax (360)
CT Unidrive SP Guide PUB-0064-04 12000 NE 60th Way Vancouver, WA 98682 Voice (360) 253-4810 Fax (360) 253-4818 www.appliedmotionsystems.com 2008-2009 Applied Motion Systems, Inc. All rights reserved. No
More information8 TS4-DDH T i g e r S t o p M a n u a l D a t a D o w n l o a d i n g. May 2006 Version 3.5 ~ 4.72 Hardware
8 TS4-DDH T i g e r S t o p M a n u a l D a t a D o w n l o a d i n g May 2006 Version 3.5 ~ 4.72 Hardware Installation & User s Guide ESC Ethernet-to-Serial Converter SX Serial Extender IMPORTANT! TigerStop
More information^2 Accessory 55E DeviceNet Option
1^ USER MANUAL ^2 Accessory 55E DeviceNet Option ^3 Universal Field Bus Adapter Network (UNET) ^4 3A0-603485-DUxx ^5 October 23, 2003 Single Source Machine Control Power // Flexibility // Ease of Use 21314
More informationCanlan INSTALLATION MANUAL
Canlan INSTALLATION MANUAL August 2014 Table of Contents Introduction... 4 Overview... 5 RJ45 Connector and Status LEDs... 5 Power Input... 6 RS232 / RS485 Connectors... 7 Installing the Canlan Software...
More informationN30 Supervisory Controller Quick Start
Issue Date June 30, 2004 TECHNICAL BULLETIN N30 Supervisory Controller Quick Start N30 Supervisory Controller Quick Start...2 Introduction... 2 Key Concepts... 3 Using This Document... 3 Related Information...
More informationProduct Family: Networking Hardware Number: AN-NH-012
APPLICATION NOTE THIS INFORMATION PROVIDED BY AUTOMATIONDIRECT.COM TECHNICAL SUPPORT These documents are provided by our technical support department to assist others. We do not guarantee that the data
More informationfactory field upgrade
CK721-A Network Controller factory field upgrade version 3.1 build 25 24-10025-75 Revision B October, 2013 Copyright 2013 Johnson Controls, Inc. All Rights Reserved No part of this document may be reproduced
More informationProcessLogix R510.0 Server Installation Instructions
ProcessLogix R510.0 Server Installation Instructions Installation Instructions Before you begin... This publication guides you through the remaining processes required to initialize a ProcessLogix Server.
More informationEQ7000. User Manual. Rev 1.00
EQ7000 User Manual Rev 1.00 www.equustek.com Revision 1.00 February 27, 2009 Contents INTRODUCTION...4 ABOUT THIS MANUAL...4 INTENDED AUDIENCE...4 HARDWARE SPECIFICATIONS...5 PHYSICAL SPECIFICATIONS...5
More information# Byrne Rd, Burnaby, BC, V5J 3J1, Canada Phone: or
EQ7000 User Manual Rev 1.04 www.equustek.com Revision 1.04 Feb 20th, 2017 #286-5489 Byrne Rd, Burnaby, BC, V5J 3J1, Canada Phone: 888-387-3787 or 604-266-8547 www.equustek.com Page 1 Contents INTRODUCTION...4
More informationACE Operation Manual
ACE Operation Manual Elecsys Director ACE Operation Manual Product Information Full information about other Elecsys products is available on our website at www.elecsyscorp.com Useful Contact Information
More informationFloBoss S600+ Field Upgrade Guide
Form Number A6299 Part Number D301668X412 February 2011 FloBoss S600+ Field Upgrade Guide Remote Automation Solutions FloBoss S600+ Field Upgrade Guide Revision Tracking Sheet February 2011 This manual
More informationMagnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual
Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual February 2006 Part Number: 140-10350 Copyright 2006 Magnetek Material Handling 2005 MAGNETEK MATERIAL HANDLING All rights reserved.
More informationQuick Setup & Getting Started
Quick Setup & Getting Started HP Compaq Business PC Copyright 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft, Windows, and
More informationProgramming Manual KX-TVA50 KX-TVA200. Voice Processing System. Model
Voice Processing System Programming Manual Model KX-TVA50 KX-TVA200 Thank you for purchasing a Panasonic Voice Processing System. Please read this manual carefully before using this product and save this
More informationApplication Note (Revision NEW) Original Instructions EGCP-3 LS Using an EGCP-3 in a Single-Phase Zig Zag Generator Application
Application Note 51247 (Revision NEW) Original Instructions EGCP-3 LS 8406-113 Using an EGCP-3 in a Single-Phase Zig Zag Generator Application General Precautions Read this entire manual and all other
More informationCommLink IV Technical Guide
www.wattmaster.com CommLink IV Technical Guide Table of Contents General Information... 3 CommLink IV Overview...3 Optional IP Module Kit...3 Optional Remote Link II...3 Installing CommLink IV ONLY...3
More informationPanelViewt 1200 Transfer Utility User Manual
User Manual Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State
More informationEthernet DHX Driver Help Ethernet DHX Driver for Allen-Bradley TCP/IP Networks
Ethernet DHX Driver Help Ethernet DHX Driver for Allen-Bradley TCP/IP Networks Version 9 ETHERNET DHX DRIVER HELP Ethernet DHX Driver for Allen-Bradley TCP/IP Networks Version 9 Copyright 1994-2017, Cyberlogic
More informationAdvanced Graphical Interface, AGI 100
APPLICATION NOTES Advanced Graphical Interface, AGI 100 The AGI communication ports Modbus details Specific DEIF driver Example of project creation Document no.: 4189340746A DEIF Screen Designer 1.293
More informationAgilent Technologies. Connectivity Guide. USB/LAN/GPIB Interfaces. Agilent Technologies
Agilent Technologies USB/LAN/GPIB Interfaces Connectivity Guide Agilent Technologies Notices Agilent Technologies, Inc. 2003-2006 No part of this manual may be reproduced in any form or by any means (including
More informationRedirector User Guide
Redirector User Guide Revision B November 04, 2005 Part Number GC-800-235 Copyright and Trademark Copyright 2004, Grid Connect, Inc. All rights reserved. No part of this manual may be reproduced or transmitted
More informationDHX Driver Help DHX Driver for A-B and SST Network Adapters
DHX Driver for A-B and SST Network Adapters Version 9 DHX DRIVER HELP DHX Driver for Allen-Bradley DH, DH+, DH-485 Networks Version 9 Copyright 1994-2017, Cyberlogic Technologies Inc. All rights reserved.
More informationPower Xpert Meter 2000 Series
Quick Start Guide IM02601002E Effective April 2017 PXM 2250 PXM 2260 PXM 2270 PXM 2280 PXM 2290 Power Xpert Meter 2000 Series Contents Description Page Mechanical Installation... 1 Electrical Wiring....
More informationDBS Manager. User Guide. Panasonic VB Please read these instructions completely before using DBS Manager.
DBS Manager User Guide Panasonic VB-43993 Please read these instructions completely before using DBS Manager. Section 550 Part Number 552X00201 Issued April 2000 The contents of this manual are subject
More informationB5021 Ethernet Base Supplemental User Guide
B5021 Ethernet Base Supplemental User Guide Overview This is a supplemental user guide for the B5021 Ethernet Base and covers the differences between the B5011 and the B5021. Refer to the B5011 manual
More informationInstallation Guide. DVI Net ShareStation GDIP201 PART NO. M1048
Installation Guide DVI Net ShareStation 1 GDIP201 PART NO. M1048 2 Table of Contents Package Contents 4 Hardware Installation 5 USB Server software installation - XP 10 DisplayLink software installation
More informationProgramming Manual KX-TVA50 KX-TVA200. Voice Processing System. Model
Voice Processing System Programming Manual Model KX-TVA50 KX-TVA200 Thank you for purchasing a Panasonic Voice Processing System. Please read this manual carefully before using this product and save this
More informationIDEA. User s Guide. Part No IDE02 Issue 1-0, April 1995 Printed in U.S.A. (183)
IDEA User s Guide Part No. 17500IDE02 Issue 1-0, April 1995 Printed in U.S.A. (183) 4 FOREST PARKWAY, SHELTON, CONNECTICUT 06484 TEL: 203-926-5400 FAX: 203-929-0535 This manual has been developed by Nitsuko
More informationSerial DHX Driver Help Serial DF1 Protocol Driver for Allen-Bradley Networks
Serial DHX Driver Help Serial DF1 Protocol Driver for Allen-Bradley Networks Version 8 SERIAL DHX DRIVER HELP Serial DF1 Protocol Driver for Allen-Bradley Networks Version 8 for Windows 8/7/Vista/XP/Server
More informationTo upgrade to the i-vu v6.0 application
i-vu Application Upgrade Guide to v6.0 CARRIER CORPORATION 2014 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-493-01 3/21/2014 Table of Contents To upgrade
More information1Developer's. Quick Start Power PMAC NC 2014
1Developer's Quick Start Power PMAC NC 2014 Delta Tau Data Systems, Inc. June, 2015 1 COPYRIGHT INFORMATION Software: 2014 Delta Tau Data Systems, Inc. All rights reserved. Software User Manual: 2014 Delta
More informationEthernet MBX Driver Help Ethernet MBX Driver for Modbus TCP Networks
Ethernet MBX Driver Help Ethernet MBX Driver for Modbus TCP Networks Version 9 ETHERNET MBX DRIVER HELP Ethernet MBX Driver for Modbus TCP Networks Version 9 Copyright 1994-2017, Cyberlogic Technologies
More informationPreparing Your Computer for OPL. User Guide Version 3.0. Information and Communications Technologies
Version 3.0 Information and Communications Technologies 2008 Department of Education. All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmitted,
More informationTofino CMP Installation & Upgrade Guide Tofino CMP Version Tofino Firmware Version 1.7.0
Tofino CMP Installation & Upgrade Guide Tofino CMP Version 1.7.0 Tofino Firmware Version 1.7.0 March 9, 2012 Copyright Information By res Security Inc and MT L Instrum ents While this information is presented
More informationVisionTouch 5 Software
User Manual VisionTouch 5 Software Greengate Contents Contents Description General Information.... 3 Hardware and Software Requirements.... 3 Hardware Requirements.... 3 Software Requirements... 3 VisionTouch
More informationNVM-Professional NVM-Server NVM-Server Desktop NVM-Server XL. Windows 2000 Platform Description and Installation Instructions
NVM-Professional NVM-Server NVM-Server Desktop NVM-Server XL Windows 2000 Platform Description and Installation Instructions This manual has been developed by NEC America, Inc. It is intended for the use
More informationEGCP-3 LS Revision R Software Revision M. Application Note (Revision NEW, 6/2009) Original Instructions
Application Note 51361 (Revision NEW, 6/2009) Original Instructions EGCP-3 LS 8406-113 Revision R Software 5418-144 Revision M Explanation of Software Changes Made for the EGCP-3 LS Control General Precautions
More informationAdvantech Studio Quick Start Manual
Advantech Studio Quick Start Manual Advantech Studio Quick Start Manual Initial Setup The WebOIT offers an easy setup feature: It takes three easy steps for your initial setup before use. Take out the
More informationSIMATIC/SINAMICS. Getting started with SINAMICS V90 PN on S Motion Control. Fundamental safety instructions 1. Introduction
Fundamental safety instructions 1 Introduction 2 SIMATIC/SINAMICS Getting started with SINAMICS V90 PN on S7-1500 Motion Control Getting Started Prepare the configuration 3 Create a project 4 Creating
More informationControlLogix Gateway Driver Help Gateway Driver for A-B ControlLogix Networks
ControlLogix Gateway Driver Help Gateway Driver for A-B ControlLogix Networks Version 9 CONTROLLOGIX GATEWAY DRIVER HELP ControlLogix Gateway Driver for Allen-Bradley ControlLogix Networks Version 9 Copyright
More informationPanelMate epro PS Family Restore Factory Image Load
PanelMate epro PS Family Restore Factory Image Load Introduction The restore factory image load kits provides a simple way for users to reset the load of the internal CompactFlash, that holds the Operating
More informationSIMATIC HMI. Software RemoteOperate V2. Preface. Overview 1. Range of functions of the RemoteOperate software. Hardware and software requirements
Preface SIMATIC HMI Software SIMATIC HMI Software Programming Manual Overview 1 Range of functions of the RemoteOperate software 2 Hardware and software requirements 3 Installing RemoteOperate 4 Server
More informationSiemens Spares. Setting up security in STEP 7. Professional SIMATIC NET. Industrial Ethernet Security Setting up security in STEP 7 Professional
Setting up security in STEP 7 Professional SIMATIC NET Industrial Ethernet Security Setting up security in STEP 7 Professional Preface 1 User interface and menu commands 2 Basic configuration 3 Firewall
More informationMagnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual
Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual March 2013 Part Number: 140-10350 R6 Copyright 2013 Magnetek Material Handling 2013 MAGNETEK MATERIAL HANDLING All rights reserved.
More informationRC-SV Configuration Guide (Rev 4)
Kramer Electronics, Ltd. RC-SV Configuration Guide (Rev 4) Software Version 2.1.2.69 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version, go
More informationUSB to Serial Converter User s Guide
USB to Serial Converter User s Guide Important Note! In order to minimize possible installation problems and/or resource conflicts: Read Me First! About This User s Guide This User s Guide is designed
More informationDocuPrint C55/C55mp Quick Network Install Guide
DocuPrint C55/C55mp Quick Network Install Guide Windows for Workgroups / Windows 95 Peer-to-Peer Network Windows NT 3.5X Network Windows NT 4.X Network Macintosh EtherTalk/TokenTalk Network Novell NetWare
More informationConfiguration Guide for Microsoft Internet Connection Sharing
Configuration Guide for Microsoft Internet Connection Sharing HUB INTERNET HOST CLIENTS Copyright 2002 Hughes Network Systems, Inc., a wholly owned subsidiary of Hughes Electronics Corporation. All rights
More informationSerial MBX Driver Help Serial MBX Driver for Modbus Networks
Serial MBX Driver Help Serial MBX Driver for Modbus Networks Version 8 Serial MBX Driver for Modbus Networks SERIAL MBX DRIVER HELP Version 8 for Windows 8/7/Vista/XP/Server 2012/Server 2008/Server 2003
More informationAllen-Bradley. User Manual. PanelView e Transfer Utility. (Cat. No. 2711E ND7)
Allen-Bradley PanelView e Transfer Utility User Manual (Cat. No. 2711E ND7) Important User Information Because of the variety of uses for the products described in this publication, those responsible for
More informationIndustrialPro Routers (SN/RAM Series) Wireless Modems
Wireless Modems Including SN/RAM-67xx LTE and RAM-9000 families Migration and Advanced Firmware Update Procedures Version 3.20/4.20 February 2015 CHANGE HISTORY Version Date Description 3.20 February 17,
More informationManagement Security Switch SGSD-1022 / SGSD-1022P SGSW-2840 / SGSW-2840P. Quick Installation Guide
Management Security Switch SGSD-1022 / SGSD-1022P SGSW-2840 / SGSW-2840P Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements... 4 3. Terminal Setup... 5 4. Logon to the Console...
More informationDS800 Development Suite Quick Start Guide for the FloBoss 107
Form A6267 Part Number D301597X012 January 2009 DS800 Development Suite Quick Start Guide for the FloBoss 107 Version 1.0 Remote Automation Solutions Revision Tracking Sheet January 2009 This manual may
More informationFERGUSON BEAUREGARD. RTU-5000 Configurator User Manual
FERGUSON BEAUREGARD RTU-5000 Configurator User Manual FERGUSON BEAUREGARD RTU-5000 Configurator User Manual The Ferguson Beauregard RTU-5000 Configurator program and manuals are Copyright 1997-2004 by
More informationGetting Started. HP Business PCs
Getting Started HP Business PCs Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Windows is a U.S. registered trademark of
More informationSERVICE INSTRUCTION. Updating the firmware and software on the RCS-2
SERVICE INSTRUCTION SI-09-04.1 Replaces (SI-09-04) March 2013 SERVICE INSTRUCTION Updating the firmware and software on the RCS-2 Important Note: It is highly recommended that all parameter data be backed
More informationPROMISE ARRAY MANAGEMENT ( PAM) USER MANUAL
PROMISE ARRAY MANAGEMENT ( PAM) USER MANUAL Copyright 2002, Promise Technology, Inc. Copyright by Promise Technology, Inc. (Promise Technology). No part of this manual may be reproduced or transmitted
More informationAllen-Bradley Motors
Installation Instructions Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers Purpose Firmware Update Kit Contents Hardware and Software Requirements This
More informationCodeLoader. Users Guide. P/N: Rev: OCT04
CodeLoader Users Guide P/N: 3100788 Rev: 1.0 04OCT04 DEVELOPED BY COPYRIGHT NOTICE TRADEMARKS CREDITS Edwards Company 6411 Parkland Drive Sarasota FL 34243 (941) 739-4300 Copyright 2004 Edwards Company
More informationUpgrading Einstein Using the Einstein 1.5 Upgrade Kit. An EAB board with Production Einstein 1.5 Software EEPROM Chips.
TECHNICAL BULLETIN Upgrading Einstein Using the Einstein 1.5 Upgrade Kit This bulletin explains how to use the components of the CPC Upgrade Kit to upgrade a pre-1.5 version Einstein unit to the latest
More informationCTC Load Utility TM User Guide
CTC Load Utility TM User Guide Doc. No. MAN-1050 Copyright 1998 Control Technology Corporation All Rights Reserved. Printed in USA The information in this document is subject to change without notice.
More informationCitectSCADA Batch Tutorial
CitectSCADA Batch Tutorial Version 1.0.8 Citect Pty Ltd 3 Fitzsimmons Lane Gordon NSW 2072 Australia www.citect.com 2 DISCLAIMER Citect Pty. Limited makes no representations or warranties with respect
More informationinstallation manual SALES AND ADMINISTRATION (toll free)
installation manual SALES AND ADMINISTRATION 800.637.2645 (toll free) 217.442.0611 sales@timeomatic.com TECHNICAL SUPPORT 866.637.2645 (toll free) service@timeomatic.com www.watchfiresigns.com Quick Start-Up
More informationConfiguring TwinCAT 3 for use with the Class 6 EtherCAT SmartMotor
Copyright Notice 2012-2016, Moog Inc., Animatics. Configuring TwinCAT 3 for use with the Class 6 EtherCAT SmartMotor,. This document, as well as the software described in it, is furnished under license
More informationLocate your Advanced Tools and Applications
File Manager allows you to take full control of your website files. You can copy, move, delete, rename and edit files, create and remove directories, change file permissions and upload files from your
More informationeth1000_large.jpg Using ICC ETH-1000 EtherNet/IP Interface with Mitsubishi iq PLC
eth000_large.jpg Using ICC EtherNet/IP Interface with Mitsubishi iq PLC Contents Contents... i FURTHER READING REFERENCE LIST... ii Chapter Chapter Chapter... -... -... -. Changing the IP Address of the
More informationAvnet Zynq Mini Module Plus Embedded Design
Avnet Zynq Mini Module Plus Embedded Design Version 1.0 May 2014 1 Introduction This document describes a Zynq standalone OS embedded design implemented and tested on the Avnet Zynq Mini Module Plus. 2
More informationCHAPTER 17 COMPILING/SIMULATING/DOWNLOADING A PANEL APPLICATION
COMPILING/SIMULATING/DOWNLOADING A PANEL APPLICATION 17.1. Compiling an Application... 1 17.1.1. Compiling an Application...1 17.1.2. Building a Panel Runtime Package...1 17.1.3. Build a List Window...2
More informationSilex SD-320AN-03 Serial Server
GE Healthcare Silex SD-320AN-03 Serial Server Firmware Upgrade Instructions 2106794-001 Revision B Silex SD-320AN-03 Serial Server English 2018 General Electric Company. All Rights Reserved. Publication
More informationPMEUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA
PMEUCM Hardware Manual PMEUCM Hardware Installation Manual This manual covers the PMEUCM hardware features and installation procedures. Effective: August 10, 2017 Niobrara Research & Development Corporation
More informationConnectPort X2 Wireless M Bus Development Kit. Getting Started Guide
ConnectPort X2 Wireless M Bus Development Kit Getting Started Guide 90001223 _B September 9, 2011 2011 Digi International, Inc. All rights reserved. Digi, idigi, Digi International, the Digi and idigi
More informationMachineShop Supplemental Installation
MachineShop Supplemental Installation Welcome to the MachineShop Supplemental Installation. This document explains how to install network communication software for MachineShop, including TCP/IP, a modem,
More informationAllen-Bradley. User Manual. DeviceView Configurator (2707-DNC)
Allen-Bradley DeviceView Configurator (2707-DNC) User Manual Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety
More informationCopley Indexer 2 Program User Guide
Copley Indexer 2 Program User Guide P/N 95-00744-000 Revision 2 June 2008 Copley Indexer 2 Program User Guide TABLE OF CONTENTS About This Manual... 6 1: Introduction... 9 1.1: Copley Controls Indexer
More informationSIMATIC. S7/HMI SIMATIC Automation Tool V3.1 SP1 product information. SIMATIC Automation Tool features 1. Known problems. Product Information
SIMATIC Automation Tool features 1 Known problems 2 SIMATIC S7/HMI SIMATIC Automation Tool V3.1 SP1 product information Product Information V3.1 SP1, 05/2018 A5E43714043-AA Legal information Warning notice
More informationUser Guide. Illustra Connect Version C0
User Guide Illustra Connect Version.0 8200-114-01 C0 Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications
More informationOWC Mercury On-The-Go Pro USER GUIDE
OWC Mercury On-The-Go Pro USER GUIDE TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 MINIMUM SYSTEM REQUIREMENTS 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.2 PACKAGE CONTENTS 1.3 ABOUT THIS MANUAL
More informationCONTENT PLAYER 9.6_CA_BBP_EN_1.0
CONTENT PLAYER 9.6_CA_BBP_EN_1.0 COPYRIGHT Copyright 1998, 2009, Oracle and/or its affiliates. All rights reserved. Oracle is a registered trademark of Oracle Corporation and/or its affiliates. Other names
More informationProLiant CL380 Software User Guide. Fourth Edition (December 2000) Part Number Compaq Computer Corporation
ProLiant CL380 Software User Guide Fourth Edition (December 2000) Part Number 157839-004 Compaq Computer Corporation Notice 2000 Compaq Computer Corporation COMPAQ and the Compaq logo, Compaq Insight Manager,
More informationTo upgrade to the i-vu v6.5 application
i-vu Application CARRIER CORPORATION 2017 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-546-01 3/10/2017 Verify that you have the most current version of this
More informationVME-Pro. Application Notes VERSION 1 JUNE, 2005
VME-Pro Application Notes VERSION 1 JUNE, 2005 NOTICE No part of this document may be reproduced or transmitted in any form or by any means (electronic, photocopying, recording, or otherwise) without the
More informationInstallation and Configuration Guide
Installation and Configuration Guide Trademark Notices Comtrol, NS-Link, and DeviceMaster are trademarks of Comtrol Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation.
More informationNetwork USB over IP Server With 1-USB2.0 Port. User Manual V1.0
Network USB over IP Server With 1-USB2.0 Port User Manual V1.0 1 2 TABLE OF CONTENTS COPYRIGHT...4 1. INTRODUCTION...5 PRODUCT OVERVIEW...5 COMPONENTS AND FEATURES...5 HARDWARE INSTALLATION...5 2. THE
More informationUpgrade Guide. BCM Business Communications Manager
Upgrade Guide BCM50 2.0 Business Communications Manager Document Status: Standard Document Number: NN40020-401 Document Version: 01.01 Part Code: N0107119 Date: October 2006 Copyright 2006 Nortel Networks,
More informationSCOPIA 100 MCU Quick Start
SCOPIA 100 MCU Quick Start Version 5.6 Multipoint Conferencing Unit NOTICE 2000-2008 RADVISIONLtd. All intellectual property rights in this publication are owned by RADVISION Ltd and are protected by Italy
More informationE-Series Troubleshooting Guide
E-Series Troubleshooting Guide Contents Troubleshooting by means of the System-OK-LED status... 5 Troubleshooting Hardware... 11 Troubleshooting Operation of the Device... 15 Troubleshooting Parameter
More information48-Port 10/100/1000Base-T with 4 Shared SFP. Managed Gigabit Switch WGSW Quick Installation Guide
48-Port 10/100/1000Base-T with 4 Shared SFP Managed Gigabit Switch WGSW-48000 Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements... 4 3. Terminal Setup... 5 4. Logon to
More informationSmartDispatch Installation Guide
SmartDispatch Installation Guide Copyright Information Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited. (the Company) in PRC and/or other countries or areas.
More informationPF31XX FAMILY FIRMWARE UPDATE GUIDE. v1.2 Revised Nov 29, 2016
PF31XX FAMILY FIRMWARE UPDATE GUIDE Revised Table of Contents 1 Overview... 1 2 Firmware Update Process... 2 3 Document Revision History... 5 Page i 1 Overview This document will assist a user in completing
More informationRC-SV Configuration Guide Revision 3
Kramer Electronics, Ltd. RC-SV Configuration Guide Revision 3 Software Version 2.1.2.32 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version,
More informationD0 DEVNETS and Allen Bradley Set up. RSNetworx
D0 DEVNETS and Allen Bradley Set up RSNetworx G 2 Setup D0 DEVNETS with Allen Bradley RSNetWorx For those who are using the D0 DEVNETS as a slave with an Allen Bradley PLC, the examples on the following
More informationBCOM-USB Device. User Manual.
BCOM-USB Device User Manual www.kalkitech.com Version 2.1.2, December 2017 Copyright Notice 2017 Applied Systems Engineering, Inc. All Rights reserved. This user manual is a publication of Applied Systems
More informationStreetWise Partner. Version 3.0. Naztec Operations Manual. April For. Published by:
Naztec Operations Manual For StreetWise Partner Version 3.0 April 2003 Published by: Naztec, Inc. 820 Park Two Drive Sugar Land, Texas 77478 Phone: (281) 240-7233 Fax: (281) 240-7238 Copyright 2003 Naztec,
More information^2 Laser Compensation
^1 USER MANUAL ^2 Laser Compensation ^3 Laser Compensation Software ^4 3AO-LASERC-xUxx ^5 October 22, 2003 Single Source Machine Control Power // Flexibility // Ease of Use 21314 Lassen Street Chatsworth,
More informationQuick KVM 1.1. User s Guide. ClearCube Technology, Inc.
Quick KVM 1.1 User s Guide ClearCube Technology, Inc. Copyright 2005, ClearCube Technology, Inc. All rights reserved. Under copyright laws, this publication may not be reproduced or transmitted in any
More informationProcomm Plus Installation Guide. Prophet 21 FASPAC 4.1
Procomm Plus Installation Guide Prophet 21 FASPAC 4.1 The documentation in this publication is provided pursuant to a Sales and Licensing Contract for the Prophet 21 System entered into by and between
More informationThe Connector. Version 1.2 Microsoft Project to Atlassian JIRA Connectivity. User Manual
The Connector Version 1.2 Microsoft Project to Atlassian JIRA Connectivity User Manual Ecliptic Technologies, Inc. Copyright 2008 www.the-connector.com Page 1 of 86 Copyright and Disclaimer All rights
More informationDCP585CW Windows Network Connection Repair Instructions
Difficulty printing from your PC can occur for various reasons. The most common reason a networked Brother machine may stop printing, is because the connection between the computer and the Brother machine
More information