SUNDE. User s Manual for NetPoint2.2 & H4S USER MANUAL FOR NETPOINT2.2 AND H4S 1

Transcription

1 SUNDE User s Manual for NetPoint2.2 & H4S USER MANUAL FOR NETPOINT2.2 AND H4S 1

2 2015 Huiyuan Co., Ltd. All rights reserved. THANK YOU FOR PURCHASING SUNDE NETWORK TERMINAL. PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. NOTE: All the information contained herein is the property of HUIYUAN. No part of this publication (whether in hardcopy or electronic form) may be reproduced or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of HUIYUAN. The software described in this document is furnished under license and may only be used or copied in accordance with the terms of such license. This publication and the information herein is furnished AS IS, is subject to change without notice, and should not be construed as a commitment by HUIYUAN. HUIYUAN assumes no responsibility or liability for any errors or inaccuracies, makes no warranty of any kind (express, implied, or statutory) with respect to this publication, and expressly disclaims any and all warranties of merchantability, fitness for particular purposes, and no infringement of third party rights. Any references to company names in sample templates are for demonstration purposes only and are not intended to refer to any actual organization. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. All other trademarks are the property of their respective owners. If this guide is distributed with software that includes an end user agreement, this guide, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by any such license, no part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of HUIYUAN. Please note that the content in this guide is protected under copyright law even if it is not distributed with software that includes an end user license agreement. The content of this guide is furnished for informational use only. It is subject to change without notice, and should not be construed as a commitment by HUIYUAN. HUIYUAN assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content continued in this guide. USER MANUAL FOR NETPOINT2.2 AND H4S 2

3 Contents 1. Introduction Components Recommended Server Configuration Connecting Software Installing Installing NetPoint2.2 Software Enabling Remote Desktop Uninstalling NetPoint2.2 Softwrae Setting up H4S Setting H4S IP Address Setting Server IP Address Setting Screen Resolution Auto Logon Advanced Settings Functions of NetPoint2.2 Management Console Terminal Information Monitoring Send Message User Accounts One-Key Broadcasting H4S Connecting to Windows or Linux Without NetPoint How to Mount USB flash drive in Linux USER MANUAL FOR NETPOINT2.2 AND H4S 3

4 1. Introduction SUNDE H4S Network Terminal is based on SOC with NetPoint2.2 tm software. It is designed to work in client-server networks and depends primarily on the central server for data processing. Its main job is to convey input and output between the user and the remote server. By using SUNDE H4S Network Terminal devices, a great deal hardware cost can be saved, much less software support is required, much less power is consumed, little desk space is occupied, and much less e-waste is generated. Based on RDP, H4S has its unique Speed-Up technology which enables it to deliver smooth HD movie playback on end user s desktop. H4S USER MANUAL FOR NETPOINT2.2 AND H4S 4

5 1.1 Components You can find the following items in the color box of the device: 1. H4S 2. Power Supply Adapter Please check to see if any part is missing or physically damaged. Contact the dealer immediately if anything is missing or damaged. Save the packaging for future use. For connecting H4S to the host (PC/Server), the following are essential: 1. An Ethernet RJ45 LAN port on the Host PC. 2. An Ethernet RJ45 cable of suitable length. 3. Ethernet switch or router is required to connect more than one Network Terminal or other network devices. Additional Ethernet cables will be required in this case. 1.2 Recommended Server Configuration You can find a detailed Server Configuration chart in H4S datasheet. Remember, the size chart is reference only. Since the workload may vary greatly in different environments, a test running is suggested if you need a more accurate server configuration data. 1.3 Connecting H4S Front H4S Back USER MANUAL FOR NETPOINT2.2 AND H4S 5

6 STEP 1. Connect your Keyboard/Mouse/Monitor/Speaker or Headphone as shown in the picture: STEP 2. Connect the Terminal to Host PC/Switch/Router using the Ethernet cable with RJ45 pins as shown below. CAUTION USE ONLY THE ORIGINAL POWER SUPPLY ADAPTER STEP 3. Connect the power adapter. USER MANUAL FOR NETPOINT2.2 AND H4S 6

7 2. Software Installing 2.1 Installing NetPoint2.2 Software Prior to installing NetPoint2.2, please make sure to DISABLE or UNINSTALL any AntiVirus or Firewall software that may be running in the background. Some Security software may interfere with the installation and operation of NetPoint2.2. They can be enabled or reinstalled after the installation of NetPoint2.2. Please visit for the latest version of NetPoint2.2. Find the location where you put NetPoint Installation Package2. In the example picture, it is put on the desktop of the host OS. Double click on it to run the installation. USER MANUAL FOR NETPOINT2.2 AND H4S 7

8 If below message pops up, choose Yes to continue: Click on Next to continue: Choose I accept the terms of the license agreement : USER MANUAL FOR NETPOINT2.2 AND H4S 8

9 Choose the installation location. Use the default destination folder. Click on Next to continue: USER MANUAL FOR NETPOINT2.2 AND H4S 9

10 Keep the default. Then Next : Now the software is installing: USER MANUAL FOR NETPOINT2.2 AND H4S 10

11 When this warning shows up, choose Install this driver software anyway : Installing virtual audio device: USER MANUAL FOR NETPOINT2.2 AND H4S 11

12 Installation is complete. Click Finish to restart the system: USER MANUAL FOR NETPOINT2.2 AND H4S 12

13 2.2 Enabling Remote Desktop We need to set the system to allow Remote Desktop so that SUNDE terminal can log on the system remotely. Take Windows 7 as the example: Go to Computer, then System properties. In the new window, click on Remote, then choose Allow connections from computers running any version of Remote Desktop. Click on OK to save. USER MANUAL FOR NETPOINT2.2 AND H4S 13

14 2.3 Uninstall NetPoint2.2 Software Click on the NetPoint Installation Package2 : Choose Remove and then click on Next to continue: USER MANUAL FOR NETPOINT2.2 AND H4S 14

15 When this pop up, choose OK to confirm uninstall: When uninstall process is finished, click on Finish to restart the system: USER MANUAL FOR NETPOINT2.2 AND H4S 15

16 3. Setting up H4S There are two kinds of IP addresses need to be set. One is terminal s Local IP, the other one is Server s IP. 3.1 Setting H4S IP Address GET DYNAMIC IP ADDRESS FROM DHCP SERVER "Dynamic Host Configuration Protocol (DHCP) is an IP standard designed to reduce the complexity of administering IP address configurations. A DHCP server would be set up with the appropriate settings for a given network. Such settings would include a set of fundamental parameters such as the gateway, DNS, subnet masks, and a range of IP addresses. Using DHCP on a network means administrators need not configure these settings individually for each client on the network. The DHCP would automatically distribute them to the clients. When the network terminal is connected to a Network having a DHCP server, the settings for the Terminals would be as follows. Click Setup, select Local tab, and choose Use Dynamic IP Address. Click Save to exit: USER MANUAL FOR NETPOINT2.2 AND H4S 16

17 Then H4S will obtain an IP address from DHCP server, and when this is successful, it will search over the network for available Servers. Results will be shown in the Host List USE STATIC IP ADDRESS FOR THE TERMINAL This would be an option exercised by users with no DHCP server environment. In a small office environment using less than 10 Terminals, this option would be more convenient. Turn on the Network terminal. Click the Setup In the Local IP tab, check Use Static IP Address. 1. IP Address: Give H4S an IP address of its own here. The easy way to do is to give it an IP address after adding 1 to the last number of IP address you gave to the Host PC. Then you can continue adding 2, 3... as you add more Terminals to the network. Each Terminal must have a Unique IP address. 2. Subnet Mask: For a C type IP address, normally it will be USER MANUAL FOR NETPOINT2.2 AND H4S 17

18 3. Gateway: Most often, this is the IP address of your Router. USER MANUAL FOR NETPOINT2.2 AND H4S 18

19 3.2 Setting Server s IP Address There are two ways to setup the server s IP address. SEARCH SERVERS IN LAN If the server is in the same subnet with the terminal, the terminal can search the network and find the server itself by set the server IP as Search servers in LAN. After save the settings, H4S will go back to Host List page, and then display all available servers (with NetPoint2.2) installed in the LAN. USER MANUAL FOR NETPOINT2.2 AND H4S 19

20 Now you can choose the right Host Server from the list and then click Connect button to connect. USE STATIC IP FOR SERVER You can setup the server using static IP address so that the terminal can logon the server directly after power on. For those Host servers that are not in the same subnet as H4S, you have to setup the IP address for the server in this way. Please be aware that, if you are connecting a H4S to a Host with NetPoint2.2, only the IP address of the host need to be supplied. If you are using the H4S to connect a Host without NetPoint2.2, the IP address plus RDP port (3389 by default) have to be typed in (see chapter 5). USER MANUAL FOR NETPOINT2.2 AND H4S 20

21 After save, the terminal will go to Host List page. After 5s counting down, H4S will try to connect to the designated Host server. 3.3 Setting Screen Resolution H4S supports 13 monitor resolutions. Please choose the correct resolution which matches best with the monitor. To change screen resolution: Click Setup, select Monitor tab. Under the Screen Resolution tab, select the desired screen resolution. Click Save. USER MANUAL FOR NETPOINT2.2 AND H4S 21

22 On this Monitor tab, you can also set the monitor to Turn off after 15 minutes or Keep monitor always on : USER MANUAL FOR NETPOINT2.2 AND H4S 22

23 3.4 Auto Logon H4S can be set to log on the host directly when power on. That means you do not need to type in user name and password each time. To set up H4S working in this way, the first step is to set H4S Server IP address as shown in the picture below. After that, go to Log On page: USER MANUAL FOR NETPOINT2.2 AND H4S 23

24 Type in User Name and Password. As for Domain Name, if H4S is being used in an Active Directory (Domain) environment, type in the Domain Name. Otherwise, just leave it open. Save the settings, and the H4S will go back to Host List page, start counting down and then log on the Host automatically using the specified username and password. If you want a certain program will run or a folder will open automatically when H4S set to auto Log On, check the Start the following program on connection and type in the full path of the program location. USER MANUAL FOR NETPOINT2.2 AND H4S 24

25 3.5 Advanced Settings To access Advanced Settings of H4S, click Setup, select Advanced tab. Here we can set up for H4S Password Protection, Firmware Update, USB ports, Sound Ports and Language. USB Ports Here you can choose to enable or disable USB ports for USB devices like USB flash drive, USB printer, etc. USB mouse and keyboard are not affected. Sound Ports You can choose to enable or disable SOUND function of H4S, both audio output and MIC input. Language Selection: Here you can select the language you prefer. Setting Password USER MANUAL FOR NETPOINT2.2 AND H4S 25

26 Password can be set to protect the settings of H4S. When password protection is enabled, you need to supply the correct password before you can access the settings page of H4S. To enable password protection, check "Enable Password Protection", type in the password that you are going to set, and then click "Save". When the below message pops up, click "OK" to take effect. Firmware Update The final part of "Advanced" setting page shown the firmware information of H4S. Here you can also update firmware of H4S. There are two ways to apply the update: by TFTP server or by USB flash drive. We have a manual on how to update firmware for SUNDE terminals by TFTP server, please refer to this manual if you want to update firmware by TFTP server. If you choose to update by USB flash drive, please copy the "n2update" folder containing firmware files (.enc /.bin) to the root of USB flash drive. After that, plug the USB drive to H4S, and click "Update Firmware": USER MANUAL FOR NETPOINT2.2 AND H4S 26

27 USER MANUAL FOR NETPOINT2.2 AND H4S 27

28 4. Functions of NetPoint2.2 Manager Console 4.1 Terminal Information In the NetPoint 2.2 Console, click on Terminal, and the console will list all H4S terminals. When click to select one H4S terminal, the desktop of this H4S will be shown in the middle. Down to the bottom, two options are available. Information displays H4S serial No., IP address, status, server IP and user account name. 4.2 Monitoring In the terminal page, a mini window of the corresponding H4S user is shown in the middle. On the right, 3 options Monitor, Message and Logout are available. Use Monitor option to have a full screen of monitoring user s desktop, Message to send message to user s desktop, and Logout to log out the user from the Host. USER MANUAL FOR NETPOINT2.2 AND H4S 28

29 Monitoring Window: User can use this monitoring function to monitor and control other accounts desktop on condition that the user must be the account Administrator and have logged in remotely. 4.3 Send Message In the terminal page, click on Dialog and you can see the txt space for typing in message. Type in your message, and then click Send. USER MANUAL FOR NETPOINT2.2 AND H4S 29

30 4.4 Account We can use the Account function of NetPont Console to set up user accounts for H4S users. Creating New Accounts: Creating one Creating multiple USER MANUAL FOR NETPOINT2.2 AND H4S 30

31 When finished: There two types of accounts can be created: Remote User (RDP) and Administrator. Now, we can go to the Local Users and Groups to check if the creation of Windows user accounts is successful. USER MANUAL FOR NETPOINT2.2 AND H4S 31

32 List of Accounts: We can also make amendments to accounts or delete accounts: USER MANUAL FOR NETPOINT2.2 AND H4S 32

33 4.5 One-Key Broadcasting Function: The One-Key Broadcasting Function is a very unique function: When Teacher H4S is input with key combination Ctrl+Alt+F10, the full desktop image of the Teacher will be broadcasted to all other H4S (students) that are connected to the same host as Teacher H4S. Audio is broadcasted at the same time. Note: the teacher account type must be Administrator and can be done only through H4S USER MANUAL FOR NETPOINT2.2 AND H4S 33

34 5. H4S Connecting to Windows or Linux without NetPoint2.2 H4S can also work alone without NetPoint2.2 being installed in the Host. In this way, H4S works as same as SUNDE another model H4, which means that the connection between H4S and the host is purely RDP, with no HD video acceleration. Steps to set H4S working without NetPoint2.2: Step1, make sure that the Host RDP (Widows) or XRDP (Linux) is enabled. Step2, go to Settings of H4S. In the server page, type in Server IP plus RDP port number. For example, :3389. Note: 3389 is the default port of RDP which can be changed manually. Save the settings, then H4S will start to connect to Host. When connection is successful, users can make use of the RDP session desktop, but with no sound and no support of other USB devices except USB flash drive. USER MANUAL FOR NETPOINT2.2 AND H4S 34

35 5.1 How to Mount USB Flash Drive in Linux When H4S is connected to a Linux host, its user can plug in USB flash drive to the H4S and use it in the Linux system by typing some commands. The command is: sudo mount //ip address of H4S/UDisk-0serial number of H4S /mnt -o username=root The below screen shot is an example as in Ubuntu host is IP address of the H4S is the serial number of the H4S (remember to and one 0 before the serial number. The serial number of H4S can be found on its product label). When the mounting process is successful, we can type in ls /mnt to check the result: USER MANUAL FOR NETPOINT2.2 AND H4S 35