EasyBuilder Pro V Added Daylight Saving Time (DST) feature in [System Parameters] and the

Size: px

Start display at page:

Download "EasyBuilder Pro V Added Daylight Saving Time (DST) feature in [System Parameters] and the"

Ethel Barton
6 years ago
Views:

Build 2015.04.02 Software Version:EasyBuilder Pro V5.01.03 New Features EasyBuilder Pro 1.

1 Build Software Version:EasyBuilder Pro V New Features EasyBuilder Pro 1. Added Daylight Saving Time (DST) feature in [System Parameters] and the relevant system registers are as follows. LB daylight saving time period (when ON) LW (16bit) : enable/disable the daylight saving time (DST) (0:disable, 1:enable) LW (16bit) : hour of the DST bias LW (16bit) : minute of the DST bias LW (16bit) : month of the year when DST starts LW (16bit) : week of the month when DST starts (1~5) LW (16bit) : day of the week when DST starts (0~ 6) LW (16bit) : hour of local time when DST starts LW (16bit) : minute of local time when DST starts LW (16bit) : month of the year when DST ends LW (16bit) : week of the month when DST ends (1~5) LW (16bit) : day of the week when DST ends (0~6) LW (16bit) : hour of local time when DST ends LW (16bit) : minute of local time when DST ends LW (16bit) : enable/disable time synchronization via NTP (Network Time Protocol) server (0:disable, 1:enable) LW (16bit) : execute time synchronization when HMI starts (0:disable, 1:enable) LW (16bit) : server response time has been adjusted in accordance with DST (0:disable, 1:enable) LW (16bit) : HMI time zone (unit : minute)

LW-11277 LW-11278 ~ LW-11281 LW-11282 ~ LW-11285 LW-11286 ~ LW-11289 LW-11290 ~ LW-11293 LW-11294 EasyBuilder Pro V5.01.

2 LW LW ~ LW LW ~ LW LW ~ LW LW ~ LW LW EasyBuilder Pro V (16bit) : server response time (server time zone) (unit : minute) (16bit) : IP 0 ~ IP 3 of network time server 1 (IP address = IP0:IP1:IP2:IP3) (16bit) : IP 0 ~ IP 3 of network time server 2 (IP address = IP0:IP1:IP2:IP3) (16bit) : IP 0 ~ IP 3 of network time server 3 (IP address = IP0:IP1:IP2:IP3) (16bit) : IP 0 ~ IP 3 of network time server 4 (IP address = IP0:IP1:IP2:IP3) (32bit) : update interval (time synchronization interval) (10 ~ 86400, unit : second) When DST ends, and the time falls back, the Trend Display object in Real-time mode will stop refreshing for the overlapping hour(s) when it just going back to standard time. However, historical data will not be affected. 2. Added Font Management feature that allows: a. Displaying the information of the fonts used in the project. b. Export the currently used font file for installing on other computers. c. Globally replace a font in the project at one time. 3. Added [Display with original size when a picture size is smaller than the object

distortion caused by enlarging the picture. 4.

3 size.] check box in Picture View object settings dialog box. When the size of the picture is smaller than the Picture View object, this setting helps to prevent distortion caused by enlarging the picture. 4. Added [ON=OFF (use state 0)] check box in the Label tab of Bit objects. If selected, both state 0 and 1 follow the settings of state Added tag name filter in Beckhoff TwinCAT PLC (Ethernet) - Free Tag Names driver.

6. Extended the range and increased the scroll speed of Alarm Bar to Speed 20. 7. The filename extension.txt can be added to the file name when using email function of Backup object.

4 6. Extended the range and increased the scroll speed of Alarm Bar to Speed The filename extension.txt can be added to the file name when using function of Backup object. This prevents the anti-virus software from blocking s. cmt Viewer 1. Upgraded cmt Viewer to Ver Trend Display object supports single touch to zoom-in/out 3. Start button (cmt-iv5) can be hidden in system setting. After it is hidden, press assigned area for 2 seconds for menu. 4. If user forgot cmt-iv5 system password, enter password default to reset password to This will reset all connection records for security reasons.

5 Corrections EasyBuilder Pro V EasyBuilder Pro 1. Allowed space in address tag names. 2. Fixed the problem where different symbols are used to denote line break in simulation and on HMI when using Recipe Import/Export. 3. Fixed the problem where a macro with space cannot be called when using SYNC_TRIG_MACRO and ASYNC_TRIG_MACRO. 4. Fixed the problem where system registers from LW to LW cannot work properly when using a cmt-svr model. 5. Fixed the problem where the system register [LB-12092: enable VNC (set ON), disable VNC (set OFF)] cannot be used by the Data Transfer object and remote HMI. 6. Fixed the problem where the mouse cursor is still displayed over keyboard when set to be hidden. 7. Fixed the problem where the ASCII Input object does not allow input by [bit control] if [Mask] feature is enabled. 8. Fixed the problem where the rectangle objects with rounded corners are misplaced by one pixel on HMI or PC. 9. Fixed the problem where the data format is forced to change to 32-bit when using Address Tag Library for objects. 10. Fixed the problem where the right-to-left texts cannot be correctly displayed in system messages. 11. Fixed the problem where the Calibri font cannot be correctly displayed on HMI. 12. Fixed the following problems regarding macros:

6 a. when an array variable with variable index is used in a conditional statement, an error may occur as the b[j] in the following example: b. when an array variable with variable index is passed to a function, an error may occur as the a[i] in the following example: c. when an array with variable index is placed in the brackets, an error may occur as shown in the following example: Recipe Editor 1. Added support for *.fmt file format of EasyBuilder Pro V3 or previous versions.

7 Drivers 1. DMX-K-SA Series driver is added. 2. FUJI SPH2000 (Ethernet) driver is added. 3. IDEC MicroSmart driver is added. 4. Added USB communication interface in VIGOR VS Series driver. 5. Modbus TCP/IP driver device types 0x_single_bit and 1x_single_bit are added to address non-consecutive addresses. 6. Added COV (Change of Value) feature in BACNet BACNet/IP driver. 7. Copley Digital Drives driver added support for multi-axial control. 8. Siemens S7-200 (Ethernet) driver device type VB is added. 9. Added [Timeout] setting for Barcode Reader. 10. Fixed the problem where IAI PCON-C-42PI driver device type SON cannot communicate properly. 11. Fixed the problem where Pass Through feature does not work with Siemens S7-200 PPI driver. 12. Renamed Siemens S (Ethernet) to Siemens S7-1200/1500 (absolute addressing) (Ethernet). This release has the following changes: a. Added device types: S5TIME_10Ms, S5TIME_100Ms, S5TIME_1S, S5TIME_10S b. Fixed the problem where device type Word-type Array is misread as Bit-type Array during import. c. Fixed the problem where SCL file with structure address type cannot be imported separately.

8 d. Fixed the problem where in TIA software, if the three consecutive addresses are: Real, Word, Real, the HMI will not be able to read/write the data in the last Real address. e. Added support for the following structure addresses: NREF, CREF, DTL, ErrorStruct, IEC_COUNTER, IEC_DCOUNTER, IEC_LCOUNTER, IEC_LTIMER, IEC_SCOUNTER, IEC_TIMER, IEC_UCOUNTER, IEC_UDCOUNTER, IEC_ULCOUNTER, IEC_USCOUNTER LDT f. Added support for the following device types: Date_And_Time, Date, EVENT_ANY, EVENT_ATT, EVENT_HWINT, HW_ANY, HW_DEVICE, HW_DPMASTE, HW_DPSLAVE, HW_HSC, HW_IEPORT HW_INTERFACE, HW_IO, HW_IOSYSTEM, HW_MODULE, HW_PTO, HW_PWM, HW_SUBMODULE, OB_ANY, OB_ATT, OB_CYCLIC, OB_DELAY, OB_DIAG, OB_HWINT, OB_PCYCLE, OB_STARTUP, OB_TIMEERROR, OB_TOD, PIP,PORT, RTM, S5Time, String, Time, Time_Of_Day 13. Renamed Siemens S (Ethernet) to Siemens S7-1200(Symbolic addressing) (Ethernet). This release has the following changes: a. Added support for space and the following symbols in tag names: -, [, ], {, } etc. b. The struct with the same name can be used in different DB. c. Tag verification can be executed upon completion of exporting address tag files or later. d. The *.db files can be imported to [Program blocks] as batch files and for several times. e. Added [Delete] setting in [Program blocks]. f. The *.db files generated by TIA 13 SP1 can be imported to [Program blocks].

9 g. Added PID_Compact, TO_Axis_PTO, PID_3Step device types for [Technology objects] to support PLCs with different firmware versions. h. Added [Delete], [Insert] settings for [Technology objects]. i. A status bar which indicates the import status will be displayed during tag import. j. A message dialog box will be displayed when importing and verifying a large amount of data. k. Prevents the program from appearing non-responsive during import and verification. l. Supports converting V3 project file to V4. m. Supports importing files that contains UDT. 14. Fixed the problem where the tags may not be completely imported in Beckhoff TwinCAT PLC (Ethernet) - Free Tag Names driver. 15. OMRON EtherNet/IP (NJ Series) or Rockwell EtherNet/IP (CompactLogix) - Free Tag Names or related Free Tag PLC drivers have the following changes: a. Fixed the problem where the index register of array-type address tag cannot be used. b. Fixed the problem where macros such as SetData(), SetDataEx(), GetData(), GetDataEx() may not work properly due to abnormal communication caused by using Data Transfer object. 16. LS Master-K Cnet and LS Master-K CPU Direct drivers have the following changes: a. TX, CX, SX, PW, KW device types are added. b. Renamed the bit addresses from ADR to ADDX. c. Renamed the word addresses from ADR_word to ADRW. (ADR represents the alphabet address name such as P, M, L, etc.)

10 17. LS XGK Cnet, LS XGK FEnet, LS XBM/XBC/XGK CPU DIRECT drivers have the following changes: a. Renamed the bit addresses from ADR_Bit to ADRX_Bit. b. Renamed the word addresses from ADR_word to ADRW. (ADR represents the alphabet address name such as P, M, L, etc.) 18. Siemens LOGO (Ethernet) driver has the following changes: a. NI, NAI, NQ, NAQ device types are added. b. Changed the address range of VD device type. c. Added support for 0BA8 PLC devices.

S Firmware V4.0 Connection Guide

S Firmware V4.0 Connection Guide Connection Guide Compatible with EB Pro V5.00.02 or later versions Table of Contents 1. Preparation... 1 Connecting HMI with PLC... 1 Exporting PLC Tags... 2 Exporting Data Block (DB)... 2 Function Block