Release Notes. VideoEdge 4.4 Patch 2

Transcription

1 Release Notes VideoEdge 4.4 Patch 2 Applicable Software VideoEdge NVR Software American Dynamics Hybrid Appliance V4.4.0 Patch 2 ( ) Product Data Visit the Network Video Recorders section of our web site to download datasheets and other documentation in PDF format. February, 2014 Note In case of discrepancy, the information in this document supersedes the information in any document referenced herein A0 Trademarked names are used throughout this document. Rather than place a symbol at each occurrence, trademarked names are designated with initial capitalization. Inclusion or exclusion is not a judgment on the validity or legal status of the term.

2 Table of Contents VideoEdge NVR Software V4.4 Patch 2 Update... 3 New VideoEdge NVR 4.4 Patch 2 (NVR_Update_Full x86_64.iso) Fixes... 3 Known Limitations... 3 Procedure for upgrading to this Patch Release... 4 Method 1: upgrade via Web GUI Method 2: upgrade via new Push Upgrade functionality (Tyco Update Utility) which is new to a victor/nvr 4.4 version release Appendix A A0

3 What s in This Patch Release VideoEdge NVR Software V4.4 Patch 2 Update New VideoEdge NVR 4.4 Patch 2 (NVR_Update_Full x86_64.iso) Fixes This patch release has the following update and fixes: New SUSE Kernel update to SUSE Version 11 SP3. Support for new VideoEdge recorders Support for the next release of the VideoEdge Hybrids (i.e. new CPU motherboards) Analog inputs on the VideoEdge Hybrids are now included when a template is created USB clip export finish message now works properly Changing the RTSP from port 554, now works with the VideoEdge Client Dry contact update to allow the duration of the dry contact to be recorded, not just the event (See Appendix A for details) Known Limitations - The upgrade paths supported for this patch release is from NVR general release or from NVR (Patch 1) Haswell motherboard release. Thus, older NVR versions must be upgraded to NVR 4.4 prior to performing this upgrade - If the RTSP port is changed, the VideoEdge Client must be stopped and restarted (i.e. performing just a Logout/Login operation will not pick up the new port value). Note: Please refer to the VideoEdge NVR & Hybrid software release notes for other details A0

4 Procedure for upgrading to this Patch Release The upgrade to this patch release can be performed in one of two methods. Method 1: upgrade via Web GUI. - Obtain the file update (NVR_Update_Full x86_64.iso) from American Dynamics website - Login into the NVR Admin Web GUI. - Go to System Update Software. - Browse and select the NVR_Update_Full x86_64.iso. - Click Upload and wait until completed. - Select the NVR_Update_Full x86_64.iso and now click Install. - Wait until the installation is completed. - Upon completion a dialog prompt appears to reboot the system. - Click OK and wait for the system to reboot. - The system will continue the installation and will reboot when complete. - System will now be patch version NVR Method 2: upgrade via new Push Upgrade functionality (Tyco Update Utility) which is new to a victor/nvr 4.4 version release. a. Download, install and deploy update packages. - Obtain push update package from American Dynamics website. - Copy the update package to the Site Manager machine (4.4 or above), ensuring there is enough free space for installation (installation will be blocked if Site Manager is not present). - Double click the update package to start the self-extraction and install process. - Follow on-screen instructions as they appear. Update will install to a default folder within the Update Server Repository folder on the Site Manager machine. b. Installing recorder push updates using victor client - Connect victor client machine (4.4 or above) to the site manager hosting the update. - Right click the VideoEdge recorder in the device list and select Check for Updates. A dialog displays informing that an update is available for that recorder. - Select Install on the dialog message to start the install. EULA displays. - Select Accept to Accept the EULA. The update download will then start followed by an automatic upgrade. victor s activity log monitors and informs of installation progress and success/failure status. - Once installed, the recorder reboots and the system will now be patch version NVR A0

5 Appendix A Dry contact Alarm Recording With this patch release, the ability now exists to record the duration of a dry contact while active. In the NVR Admin Web GUI, on the Devices Alarms Sensors Page when defining an action, two new options have been added to the Action pulldown options: Camera Recording Camera Start Recording New Camera Stop Recording New PTZ to Preset Camera Recording The Sensor will only be triggered by the selected Input State from the section above. If the Recording Mode is set to Record-Only-On-Alarm (orange triangle), recording will begin and will include only the following: Alarm Pre Buffer + selected Sensor Input State trigger time + Alarm Post Buffer After the configured Alarm Post Buffer, recording will turn off A0

6 Camera Start Recording Similar to Camera Recording above, the Sensor will only be triggered by the selected Input State. Recording (including Alarm Pre Buffer) will begin and will continue indefinitely. Camera Stop Recording The Sensor will only be triggered by the selected Input State. Video (including Alarm Post Buffer) will be recorded and then recording will turn off. When used in conjunction with the Camera Start Recording action, the following will be recorded: Alarm Pre Buffer + selected Sensor Input (High) State trigger time + selected Sensor Input (Low) State trigger time + Post Buffer Note: It is these two new actions that allow video recording to continue for as long as the Dry Contact is active PTZ-to-Preset When the configured Input State is triggered, the selected PTZ camera will move to the appropriate Preset position. This could be the same camera that the Dry Contact is enabled on, or it could be a different PTZ camera. Unless there is also an additional action created, recording will -not- be activated A0

7 Contact Information If you have any questions regarding this Release Notes, please contact American Dynamics Technical Services at: Toll Free , Option 2 International , Option 2 Fax adtechservices@tycoint.com Web Site Hours 08:00 20:00 EST In Europe, contact EMEA / APAC Technical Support at: Toll Free Local Direct Dial Numbers: Bahrain Belgium France Germany Greece Italy Spain Russia Turkey United Arab Emirates United Kingdom Technical Post-Sales Inquires emea.support@tycint.com Technical Pre-Sales Inquires emea.presales@tycoint.com Technical Training Inquires emea.training@tycoint.com Web Site Hours 08:00 18:00 CET Important Note: In case of discrepancy, the information in this document supersedes the information in any document referenced herein. Information furnished by American Dynamics is believed to be accurate and reliable. However, no responsibility is assumed by American Dynamics for its use, nor any infringements of other rights of third parties which may result from its use. No license is granted by implications or otherwise under any patent rights of American Dynamics A0