NB6Plus4W Rev 2 Firmware Release Notes

Transcription

1 Information NetComm Product Name NB6Plus4W Rev 2 New Zealand NetComm Product Description ADSL2+ 4-port Wireless Modem Router with USB Firmware Version 4.24x_NZ Wireless Version DSL Version A2pB030a.d22k Official / Beta Firmware Official Release Candidate File Name cfe-nb6plus4w_rev2_nz-v424x_a2pb030a_d22k File Size 3.46 MB Date 1 st of November 2010 Upgrade Instruction 1. Connect the correct PSU into the Power port of the NB6Plus4W Rev 2 and power it On by pressing the Power button next to the Power port. 2. Connect the computer to any LAN socket on the NB6Plus4W Rev 2 and wait for about 2 minutes until the computer gets the proper IP address ( x, x=2-254) 3. On the computer, open any web browser and type in the NB6Plus4W Rev 2 IP address (by default is in the address bar and hit Enter. 4. Navigate to Management > Update Firmware 5. Click Browse and select the firmware file (cfe-nb6plus4w_rev2_nz-v424x_a2pb030a_d22k) and press Open. 6. Click Update Software. Warning: do not power off the NB6Plus4W Rev 2 during firmware Page 1 of 6

2 update process. The process should take about 3-5 minutes. 7. Once it is done, please check the bottom left corner of the Web UI and make sure the Firmware is 4.24x. 8. Navigate to Management > Reset Router, tick Reset to factory default settings if you decide to reset the configurations back to default settings. Support new DSL driver A2pB030a with PhYR forward error correction technology Changed default SSID to Netcomm Wireless Internet Time Zone is currently set to (GMT+10) Canberra, Melbourne, Sydney Version History 4.24w Fixed bug: CPE will restore the same config file Fixed bug: PPPoA cannot be triggered up after modification Fixed bug: full cone NAT is not working Fixed bug: issue with XML API Fixed bug: increase the time of web GUI time-out Fixed bug: Delete the Remove button if there is no entry in Layer 2 Interface list Page 2 of 6

3 4.24s New CLI command to control firewall (IP Filter): firewall ipfilter [enable disable show] Added --reboot option to wan add and wan edit Added External host IP address (single/subnet) in port forwarding New DSL driver d22k support since this release. Fixed bug: Wireless WPA/WPA2 not working Fixed bug: Default NZ 0/100 PPPoA PVC cannot access Internet Fixed bug: Auto provision on LAN is not working 4.24p Fixed bug: RTA1025W_Rev2_AU default Bridged PVC for IPTV is not working Fixed bug: P2P traffic run out of CPE memory causes CPE not stable and slow response on CPE GUI Fixed bug: firewall enable/ disable status on Internet connect is not consistent to IP filter configuration Fixed bug: CLI command QoS enable/ disable is not working 4.24k PPPoA PVC scan support Support PPP CLI command wan edit for WAN interface Command format: wan edit service <L2interfacename/(port_vpi_vci)> --protocol [<pppoe> <pppoa>] --wanl3ifname <ppp0 pppoa0> [--nat Page 3 of 6

4 <enable disable>] [--igmp <enable disable>] [--mtu <mtu value>] [- -username <username> --password <password>] For example: wan edit service atm0/0_0_100 --protocol pppoa --wanl3ifname pppoa0 nat disable --igmp disable --mtu username askey2 -- password askey2 Extended unanswered PPP echo request from 3 to 6 for P2P which causes PPP drops issue Fixed bug: When there is LAN activity, the WLAN LED will also flash at the same time intermittently Fixed bug: CPE needs rebooting for NAT configuration (enable/ disable) on GUI to take effect. Fixed bug: P2P causes CPE crashes 4.24f NB6Plus4W_Rev2_NZ new profile support since this release. Fixed bug: PPP CLI command should allow MTU to be 1500 on PPPoA mode Fixed bug: Static DNS GUI more mapping link does not work Fixed bug: time server changed to time.windows.com and time.nist.gov 4.24e Fixed bug: removed syntax error on WAN CLI output Fixed bug: Wireless key is not compatible to 4.22z series firmware Page 4 of 6

5 4.24a Compatibility to 4.22z series configuration file CLI support to create/ delete PPP connections Command usage example: wan delete service ppp0 wan delete interface atm wan add interface atm linktype PPPoA --qos enable -- encap vcmux wan add service atm0/(0_0_100) --protocol pppoa --igmp enable - -username askey1 --password askey1 --mtu 1492 Fixed bug: cannot associate to the AP with the wireless security default settings Fixed bug: wireless LED light is not working Fixed bug: some IP tables rules are duplicated when creating or removing Port Forwarding rules. 4.23y RTA1025W_Rev2_AU new default settings: 2PVCs and IGMP snooping enabled in blocking mode Auto provision on LAN support Fixed bug: Telnet session will show up the correct password on the command prompt 4.23b Broadcom codebase support RTA1025W_NZ IPv6 support Ethernet WAN support Page 5 of 6

6 Firmware downgrade from 4.23b to 3.6x then re-upgrade to 4.23b will brick the modem router Warning: The NB6Plus4W REV2 firmware and configuration file are not interchangeable with REV1 The NB6Plus4W REV2 configuration file backup from 4.24x cannot be restored to modem running firmware 4.22z code base. Page 6 of 6