E-Series Converting the Protocol of E2800 Host Ports (New Systems)
|
|
- Whitney Flynn
- 5 years ago
- Views:
Transcription
1 E-Series Converting the Protocol of E2800 Host Ports (New Systems) October _A0
2
3 Table of Contents 3 Contents Converting the Protocol of E2800 Host Ports (New Systems)... 4 Obtaining the feature pack... 6 Changing the feature pack... 8 After converting the protocol of the host (new systems)... 9 Copyright information Trademark information How to send comments about documentation and receive update notifications... 12
4 4 Converting the Protocol of E2800 Host Ports (New Systems) If you have a new E2800 storage array with Fibre Channel (FC) host, you can use these instructions to convert the host port protocol to iscsi. Important: If you want to convert the host port protocol of a storage array that has already been in use, you must refer to Converting the Protocol of E2800 Host Ports instead. Before starting this procedure, make sure that you have completed the following tasks. Note: To complete these tasks, follow the procedures in the Installation and Setup Instructions provided in the box with the storage array. Installed the storage array and drives. Powered on the storage array and management host. Connected by Ethernet to the SANtricity System Manager GUI. Since you are working with a new E2800, you should not have made any data host connections or configured the array. The following figure shows the back of an E2800 controller that has two SFP+ (optical) baseboard host and four SFP+ (optical) HIC. Callout 1 2 Type of host Two-port SFP+ (optical) baseboard Four-port SFP+ (optical) HIC Note: A two-port HIC is also available. The baseboard host and the HIC can use the same host protocol or different host protocols. The table shows which host you can convert using a feature pack.
5 Converting the Protocol of E2800 Host Ports (New Systems) 5 These baseboard host... Two SFP+ (optical) Two RJ-45 (base-t) If you have... And these HIC... Two or four SFP+ (optical) Two or four SAS Two RJ-45 (base-t) None Two RJ-45 (base-t) None You can convert... All of the Only the baseboard host None of the Related information NetApp E-Series and EF-Series Systems Documentation Center NetApp Support
6 6 Obtaining the feature pack To obtain the feature pack, you need the serial number from the controller shelf, a Feature Activation Code, and the Feature Enable Identifier for the storage array. Steps 1. Locate the serial number and the controller submodel ID. a. From SANtricity System Manager, select Support > Support Center. b. With the Support Resources tab selected, scroll to the View top storage array properties section. c. Locate the Chassis Serial Number, and copy this value to a text file. 2. Locate the Controller submodel ID, and use that value to look up the Feature Activation Code that applies to your starting configuration and your desired ending configuration. Then, copy the Feature Activation Code to a text file. Starting configuration Ending configuration Feature Activation Code Control ler submod el ID Basebo ard HIC Control ler submod el ID Basebo ard HIC 318 FC FC 319 FC iscsi ZGW-4L2-Z36IJ 320 iscsi FC 4GZ-NL2-Z4NRP 321 iscsi iscsi TG2-7L2-Z5485
7 Obtaining the feature pack 7 Starting configuration Ending configuration Feature Activation Code Control ler submod el ID Basebo ard HIC Control ler submod el ID Basebo ard HIC 338 FC FC 339 FC iscsi PGC-RK2-ZREUT 340 iscsi FC MGF-BK2-ZSU3Z 341 iscsi iscsi NGR-1L2-ZZ8QC Note: If your submodel ID is not listed, contact NetApp Support. 3. In System Manager, locate the Feature Enable Identifier. a. Go to Settings > System. b. Scroll down to Add-ons. c. Under Change Feature Pack, locate the Feature Enable Identifer. d. Copy and paste this 32-digit number to a text file. 4. Go to NetApp License Activation: Storage Array Premium Feature Activation, and enter the information required to obtain the feature pack. Chassis serial number Feature Activation Code Feature Enable Identifier Important: The Premium Feature Activation web site includes a link to Premium Feature Activation Instructions. Do not attempt to use those instructions for this procedure. 5. Choose whether to receive the key file for the feature pack in an or download it directly from the site.
8 8 Changing the feature pack You can change the feature pack to convert the host protocol of the baseboard host, the HIC, or both types of. Steps 1. From SANtricity System Manager, select Settings > System. 2. Under Add-ons, select Change Feature Pack. 3. Click Browse, and then select the feature pack you want to apply. 4. Type CHANGE in the field. 5. Click Change. The feature pack migration begins. Both controllers automatically reboot twice to allow the new feature pack to take effect. The storage array returns to a responsive state after the reboot is complete. 6. Confirm the host have the protocol you expect. a. From SANtricity System Manager, select Hardware. b. Click Show back of shelf. c. Select the graphic for either Controller A or Controller B. d. Select View settings from the context menu. e. Select the Host Interfaces tab. f. Click Show more settings. g. Review the details shown for the baseboard and the HIC (labeled slot 1 ), and confirm that each type of port has the protocol you expect.
9 9 After converting the protocol of the host (new systems) After converting the protocol of the host, follow the instructions in the SANtricity System Manager Express Guide or SANtricity Power Guide for Advanced Users for your operating system to complete the setup for each protocol. Related information E-Series and EF-Series Systems Hardware Cabling Guide SANtricity System Manager Installing and Configuring for Linux Express Guide SANtricity System Manager Installing and Configuring for VMware Express Guide SANtricity System Manager Installing and Configuring for Windows Express Guide SANtricity Installing and Configuring for Linux Power Guide for Advanced Users SANtricity Installing and Configuring for VMware Power Guide for Advanced Users SANtricity Installing and Configuring for Windows Power Guide for Advanced Users NetApp Interoperability Matrix Tool
10 10 Copyright information Copyright NetApp, Inc. All rights reserved. Printed in the U.S. No part of this document covered by copyright may be reproduced in any form or by any means graphic, electronic, or mechanical, including photocopying, recording, taping, or storage in an electronic retrieval system without prior written permission of the copyright owner. Software derived from copyrighted NetApp material is subject to the following license and disclaimer: THIS SOFTWARE IS PROVIDED BY NETAPP "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED. IN NO EVENT SHALL NETAPP BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. NetApp reserves the right to change any products described herein at any time, and without notice. NetApp assumes no responsibility or liability arising from the use of products described herein, except as expressly agreed to in writing by NetApp. The use or purchase of this product does not convey a license under any patent rights, trademark rights, or any other intellectual property rights of NetApp. The product described in this manual may be protected by one or more U.S. patents, foreign patents, or pending applications. RESTRICTED RIGHTS LEGEND: Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS (October 1988) and FAR (June 1987).
11 11 Trademark information Active IQ, AltaVault, Arch Design, ASUP, AutoSupport, Campaign Express, Clustered Data ONTAP, Customer Fitness, Data ONTAP, DataMotion, Fitness, Flash Accel, Flash Cache, Flash Pool, FlexArray, FlexCache, FlexClone, FlexGroup, FlexPod, FlexScale, FlexShare, FlexVol, FPolicy, Fueled by SolidFire, GetSuccessful, Helix Design, LockVault, Manage ONTAP, MetroCluster, MultiStore, NetApp, NetApp Insight, OnCommand, ONTAP, ONTAPI, RAID DP, RAID-TEC, SANscreen, SANshare, SANtricity, SecureShare, Simplicity, Simulate ONTAP, Snap Creator, SnapCenter, SnapCopy, SnapDrive, SnapIntegrator, SnapLock, SnapManager, SnapMirror, SnapMover, SnapProtect, SnapRestore, Snapshot, SnapValidator, SnapVault, SolidFire, SolidFire Helix, StorageGRID, SyncMirror, Tech OnTap, Unbound Cloud, and WAFL and other names are trademarks or registered trademarks of NetApp, Inc., in the United States, and/or other countries. All other brands or products are trademarks or registered trademarks of their respective holders and should be treated as such. A current list of NetApp trademarks is available on the web.
12 12 How to send comments about documentation and receive update notifications You can help us to improve the quality of our documentation by sending us your feedback. You can receive automatic notification when production-level (GA/FCS) documentation is initially released or important changes are made to existing production-level documents. If you have suggestions for improving this document, send us your comments by . To help us direct your comments to the correct division, include in the subject line the product name, version, and operating system. If you want to be notified automatically when production-level documentation is released or important changes are made to existing production-level documents, follow Twitter You can also contact us in the following ways: NetApp, Inc., 495 East Java Drive, Sunnyvale, CA U.S. Telephone: +1 (408) Fax: +1 (408) Support telephone: +1 (888)
FlexArray Virtualization Implementation Guide for NetApp E-Series Storage
ONTAP 9 FlexArray Virtualization Implementation Guide for NetApp E-Series Storage June 2017 215-11151-C0 doccomments@netapp.com Updated for ONTAP 9.2 Table of Contents 3 Contents Where to find information
More informationReplacing a Drive in E2660, E2760, E5460, E5560, or E5660 Trays
E-Series Replacing a Drive in E2660, E2760, E5460, E5560, or E5660 Trays The Recovery Guru in SANtricity Storage Manager monitors the drives in the storage array and can notify you of an impending drive
More informationOnCommand Cloud Manager 3.2 Provisioning NFS Volumes Using the Volume View
OnCommand Cloud Manager 3.2 Provisioning NFS Volumes Using the Volume View April 2017 215-12036_B0 doccomments@netapp.com Table of Contents 3 Contents Logging in to Cloud Manager... 4 Creating NFS volumes...
More informationFlexArray Virtualization
Updated for 8.2.4 FlexArray Virtualization Implementation Guide for NetApp E-Series Storage NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501
More informationFlexArray Virtualization
Updated for 8.3.2 FlexArray Virtualization Implementation Guide for NetApp E-Series Storage NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501
More informationFlexArray Virtualization
FlexArray Virtualization Implementation Guide for NetApp E-Series Storage NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone:
More informationVolume Disaster Recovery Express Guide
ONTAP 9 Volume Disaster Recovery Express Guide December 2017 215-11188_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 Volume disaster
More informationSNMP Configuration Express Guide
ONTAP 9 SNMP Configuration Express Guide December 2017 215-11190_D0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 SNMP configuration
More informationReplacing a Power Canister in E5760 or E2860 Shelves
E-Series Replacing a Power Canister in E5760 or E2860 Shelves Each 60-drive controller shelf or drive shelf includes two power canisters for power redundancy. If a power canister fails, you must replace
More informationSnapCenter Software 3.0 Importing Data from SnapManager to SnapCenter
SnapCenter Software 3.0 Importing Data from SnapManager to SnapCenter July 2017 215-12093_A0 doccomments@netapp.com Table of Contents 3 Contents Deciding on whether to read this information... 4 Importing
More informationReplacing a Power-Fan Canister in E5700 or E2800 Shelves
E-Series Replacing a Power-Fan Canister in E5700 or E2800 Shelves Each 12-drive or 24-drive controller shelf or drive shelf includes two power supplies with integrated fans. These are referred to as power-fan
More informationClustered Data ONTAP 8.3
Clustered Data ONTAP 8.3 Volume Disaster Recovery Preparation Express Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone:
More informationReplacing a drive in E5724 shelves
E-Series Replacing a drive in E5724 shelves The Recovery Guru in SANtricity System Manager monitors the drives in the storage array and can notify you of an impending drive failure or an actual drive failure.
More informationInventory Collect Tool 1.4
Inventory Collect Tool 1.4 Host and Storage Information Collection Guide For Transition Assessment NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501
More informationDisaster Recovery for Enterprise Applications with ONTAP Cloud
Technical Report Disaster Recovery for Enterprise Applications with ONTAP Cloud Step-by-Step Guide Shmulik Alfandari, NetApp September 2016 TR-4554i Abstract This document describes the required steps
More informationNavigating VSC 6.1 for VMware vsphere
Navigating VSC 6.1 for VMware vsphere Virtual Storage Console for VMware vsphere works with the VMware vsphere Web Client and has dropped support for the VMware Desktop Client. This change means that VSC
More informationiscsi Configuration for Windows Express Guide
ONTAP 9 iscsi Configuration for Windows Express Guide December 2017 215-11180_D0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 iscsi
More informationNetApp Data ONTAP Edge on SoftLayer
Technical Report NetApp Data ONTAP Edge on SoftLayer Express Setup Guide Jarod Rodriguez, NetApp April 2016 TR-4502 Abstract This document provides instructions on how to quickly install NetApp Data ONTAP
More informationClustered Data ONTAP 8.3
Updated for 8.3.1 Clustered Data ONTAP 8.3 Using All Flash FAS with Clustered Data ONTAP NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support
More informationAll other components in the system must be functioning properly; if not, you must contact technical support.
62xx systems For all operating environments Replacing a chassis To replace the chassis, you must remove the controller module or modules and I/O expansion module, when present, from the old chassis, remove
More informationSMB/CIFS Configuration Express Guide
ONTAP 9 SMB/CIFS Configuration Express Guide November 2017 215-11170_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 SMB/CIFS configuration
More informationWindows Unified Host Utilities 7.0 Using Windows Hosts with ONTAP Storage
Windows Unified Host Utilities 7.0 Using Windows Hosts with ONTAP Storage March 2017 215-09444_B0 doccomments@netapp.com Table of Contents 3 Contents Preparing to use Windows hosts with ONTAP storage...
More informationReplacing a Failed Controller Canister in a E2760 Controller- Drive Tray
E-Series Replacing a Failed Controller Canister in a E2760 Controller- Drive Tray To replace a failed E2700 controller canister in a duplex configuration, you remove the controller canister from the E2760
More informationNFS Client Configuration for ESX Express Guide
ONTAP 9 NFS Client Configuration for ESX Express Guide December 2017 215-11183_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 NFS
More informationInventory Collect Tool 2.2
Inventory Collect Tool 2.2 Host and Storage Information Collection Guide For Transition Assessment NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501
More informationFC Configuration for ESX Express Guide
ONTAP 9 FC Configuration for ESX Express Guide March 2017 215-11179-C0 doccomments@netapp.com Updated for ONTAP 9.1 Table of Contents 3 Contents Deciding whether to use this guide... 4 FC configuration
More informationOnCommand Cloud Manager 3.2 Updating and Administering Cloud Manager
OnCommand Cloud Manager 3.2 Updating and Administering Cloud Manager April 2017 215-12037_B0 doccomments@netapp.com Table of Contents 3 Contents Updating Cloud Manager... 4 Enabling automatic updates...
More informationFC Configuration for Windows Express Guide
ONTAP 9 FC Configuration for Windows Express Guide December 2017 215-11173_D0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 FC configuration
More informationSolidFire and AltaVault
Technical Report SolidFire and AltaVault Back Up SolidFire Storage to the Cloud by Using AltaVault Mike Braden, NetApp August 2016 TR-4542 Abstract Effectively using storage at scale is how organizations
More informationOnCommand Cloud Manager 3.0 Administration Guide
OnCommand Cloud Manager 3.0 Administration Guide June 2016 215-11111_A0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this guide... 4 Backing up Cloud Manager... 5 Removing
More informationInstalling a Cisco Nexus 3132Q-V cluster switch and a passthrough panel in a NetApp cabinet
Installing a Cisco Nexus 332Q-V cluster switch and a passthrough panel in a NetApp cabinet You can install the Cisco Nexus 332Q-V switch and pass-through panel in a NetApp cabinet with the standard brackets
More informationNDMP in Clustered Data ONTAP for Tape Backup Software Applications
Technical Report NDMP in Clustered Data ONTAP for Tape Backup Software Applications Subhash Athri, NetApp June 2015 TR-4376 TABLE OF CONTENTS 1 NDMP Backups... 3 1.1 Tape Backup Topologies in Clustered
More informationiscsi Configuration for ESX Express Guide
ONTAP 9 iscsi Configuration for ESX Express Guide December 2017 215-11181_D0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 iscsi configuration
More informationReplacing a Drive Drawer in a 60-Drive Tray
E-Series Replacing a Drive Drawer in a 60-Drive Tray The steps to replace a failed drive drawer in an E-Series 60-drive tray depend on whether the volumes in the drawer are protected by Drawer Loss Protection.
More informationReplacing the chassis
AFF A200 systems Replacing the chassis Before you begin All other components in the system must be functioning properly; if not, you must contact technical support. About this task You can use this procedure
More informationNFS Configuration Express Guide
ONTAP 9 NFS Configuration Express Guide December 2017 215-11172_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 NFS configuration workflow...
More informationAll other components in the system must be functioning properly; if not, you must contact technical support.
80xx systems For all operating environments Replacing a chassis To replace the chassis, you must remove the power supplies, fan modules, and controller module or modules and I/O expansion module, when
More informationReplacing the chassis
FAS8200 systems Replacing the chassis To replace the chassis, you must move the power supplies, fans, and controller modules from the impaired chassis to the new chassis, and swap out the impaired chassis
More informationReplacing the chassis
FAS9000 and AFF A700 systems Replacing the chassis Before you begin All other components in the system must be functioning properly; if not, you must contact technical support. About this task You can
More informationReplacing a Cisco Nexus 5596 cluster switch
Replacing a Cisco Nexus 5596 cluster switch Replacing a defective Cisco Nexus 5596 cluster switch in a cluster network is a nondisruptive procedure (NDU). Before you begin The following conditions must
More informationReplacing a Battery in E2800 or E5700 Shelves
E-Series Replacing a Battery in E2800 or E5700 Shelves Each controller canister in an E5700 or E2800 storage array includes a battery that preserves cached data if the AC power fails. To protect your data,
More informationInstalling and Configuring for AIX
SANtricity System Manager 11.30 Installing and Configuring for AIX Express Guide August 2016 215-11221_A0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this Express Guide...
More informationReplacing Cisco Nexus 3132Q-V cluster switches
Replacing Cisco Nexus 3132Q-V cluster switches You must be aware of certain configuration information, port connections and cabling requirements when you replace Cisco Nexus 3132Q-V cluster switches. The
More informationCluster Switch Setup Guide for Cisco Switches. October _A0_ur005
Cluster Switch Setup Guide for Cisco Switches October 2017 215-06775_A0_ur005 doccomments@netapp.com Table of Contents 3 Contents Switches supported by ONTAP... 4 Setting up the switches... 5 Required
More informationReplacing an E5700 or E2800 Controller (Duplex Configuration)
E-Series Replacing an E5700 or E800 Controller (Duplex Configuration) Each controller canister contains a controller card, a battery, and, optionally, a host interface card (HIC). When you replace a controller
More informationAll Flash FAS SAN-Optimized Configuration
Technical Report All Flash FAS SAN-Optimized Configuration Michael Peppers, NetApp June 2016 TR-4480 Abstract This technical report provides details about the SAN-optimized configuration for NetApp All
More informationClustered Data ONTAP 8.3
Clustered Data ONTAP 8.3 FC Configuration for ESX Express Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone: +1 (888)
More informationSolidFire CLI Tools Release Notes
NetApp SolidFire CLI Tools Release Notes Version 1.5 November 2017 215-12706_A0_ur001 doccomments@netapp.com Table of Contents 3 Contents About these release notes... 4 New in this release... 5 Known
More informationHadoop Online NoSQL with NetApp FAS NFS Connector for Hadoop
Technical Report NetApp FAS and HBase Hadoop Online NoSQL with NetApp FAS NFS Connector for Hadoop Ankita Dhawale and Karthikeyan Nagalingam, NetApp September 2016 TR-4541 Abstract This document introduces
More informationCluster and SVM Peering Express Guide
ONTAP 9 Cluster and SVM Peering Express Guide December 2017 215-11182_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 Prerequisites
More information7-Mode Transition Tool 3.3 Installation and Setup Guide
7-Mode Transition Tool 3.3 Installation and Setup Guide September 2017 215-12329-A0 doccomments@netapp.com Table of Contents 3 Contents Transition to ONTAP by using the 7-Mode Transition Tool... 4 Comparison
More informationReplacing drives for SolidFire storage nodes
NetApp Replacing drives for SolidFire storage nodes You can hot-swap a failed solid-state disk (SSD) drive with a replacement drive. Before you begin You have a replacement drive. You have an electrostatic
More informationONTAP 9. Software Setup Guide. November _E0 Updated for ONTAP 9.3
ONTAP 9 Software Setup Guide November 2017 215-11142_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 Cluster setup workflows... 5 Setting
More informationNetApp SolidFire Element OS. Setup Guide. Version March _A0
NetApp SolidFire Element OS Setup Guide Version 10.2 March 2018 215-12911_A0 doccomments@netapp.com Table of Contents 3 Contents SolidFire system overview... 4 Configuring a storage node... 5 Configuring
More informationNetApp System Manager 1.1 Quick Start Guide
NetApp System Manager 1.1 Quick Start Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 USA Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone: +1 (888) 4-NETAPP Documentation
More informationVolume Move Express Guide
ONTAP 9 Volume Move Express Guide June 2018 215-11197_G0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this guide... 4 Volume move workflow... 5 Planning the method and timing
More informationOnCommand Unified Manager Reporting for Clustered Data ONTAP
Technical Report OnCommand Unified Manager Reporting for Clustered Data ONTAP Dhiman Chakraborty, NetApp October 2015 TR-4122i Abstract This technical report (TR) introduces the reporting features that
More informationUpgrade Express Guide
ONTAP 9 Upgrade Express Guide December 2017 215-11234_G0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide... 4 Cluster software update workflow...
More informationInstalling and Configuring for VMware
SANtricity System Manager 11.41 Installing and Configuring for VMware Express Guide December 2017 215-11894_B0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this Express
More informationSMB/CIFS and NFS Multiprotocol Configuration Express Guide
ONTAP 9 SMB/CIFS and NFS Multiprotocol Configuration Express Guide December 2017 215-11171_F0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use this guide...
More informationStorageGRID Webscale NAS Bridge Management API Guide
StorageGRID Webscale NAS Bridge 2.0.3 Management API Guide January 2018 215-12414_B0 doccomments@netapp.com Table of Contents 3 Contents Understanding the NAS Bridge management API... 4 RESTful web services
More informationAIX Host Utilities 6.0 Release Notes
IBM System Storage N series AIX Host Utilities 6.0 Release Notes GC53-1180-03 Contents AIX Host Utilities 6.0 Release Notes...................... 1 The 6.0 release of the AIX Host Utilities......................
More informationOptimizing SAP Lifecycle Management with NetApp Solutions for SAP HANA
Technical Report Optimizing SAP Lifecycle Management with NetApp Solutions for SAP HANA Nils Bauer, NetApp July 2015 TR-4439 Abstract This technical report describes the optimization of SAP lifecycle management
More informationInstalling and Configuring for Windows
SANtricity System Manager 11.41 Installing and Configuring for Windows Express Guide December 2017 215-11887_B0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this Express
More informationNetApp SANtricity Storage Replication Adapter 5.6 Best Practices Guide
NetApp SANtricity Storage Replication Adapter 5.6 Best Practices Guide September 2016 215-10052_C0 doccomments@netapp.com TABLE OF CONTENTS SRA DOWNLOAD... 2 INSTALLATION PROCEDURE... 2 PASSWORD PROTECTED
More informationInstalling and Configuring for Windows
SANtricity Storage Manager 11.40 Installing and Configuring for Windows Express Guide September 2017 215-11886_A0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this Express
More informationE-Series Cabling E-Series Hardware
E-Series Cabling E-Series Hardware September 2018 215-13049_A0 doccomments@netapp.com Table of Contents 3 Contents Overview and requirements... 4 Cabling your storage system... 5 Host cabling... 5 Cabling
More informationVolume Disaster Recovery Preparation Express Guide
ONTAP 9 Volume Disaster Recovery Preparation Express Guide August 2018 215-11187_F0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this guide... 4 Volume disaster recovery
More informationInstalling and Configuring for VMware
SANtricity Storage Manager 11.40 Installing and Configuring for VMware Express Guide September 2017 215-11892_A0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use this Express
More informationiscsi Configuration for ESXi using VSC Express Guide
ONTAP 9 iscsi Configuration for ESXi using VSC Express Guide May 2018 215-11181_E0 doccomments@netapp.com Updated for ONTAP 9.4 Table of Contents 3 Contents Deciding whether to use this guide... 4 iscsi
More informationReplacing a PCIe card
AFF A800 systems Replacing a PCIe card To replace a PCIe card, you must disconnect the cables from the cards, remove the SFP and QSFP modules from the cards before removing the riser, reinstall the riser,
More informationE-Series and EF-Series Systems
E-Series and EF-Series Systems Controller Upgrade Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone: +1 (888) 463-8277
More informationReplacing a PCIe card
AFF A700s systems Replacing a PCIe card To replace a PCIe card, you must disconnect the cables from the cards in the riser, remove the riser, replace the riser, and then recable the cards in that riser.
More informationHCI File Services Powered by ONTAP Select
Technical Report HCI File Services Powered by ONTAP Select Quick Start Guide Aaron Patten, NetApp March 2018 TR-4669 Abstract NetApp ONTAP Select extends the NetApp HCI product, adding a rich set of file
More informationNetApp SANtricity Cloud Connector 3.0 User Guide
NetApp SANtricity Cloud Connector 3.0 User Guide December 2017 215-12513_A0 doccomments@netapp.com Table of Contents Deciding whether to use this guide... 1 Understanding the SANtricity Cloud Connector...
More informationNetApp Storage Replication Adapter for E- Series Installation and User Guide
NetApp Storage Replication Adapter for E- Series Installation and User Guide NetApp, Inc. Telephone: +1 (408) 822-6000 Part number: 215-08653_A0 495 East Java Drive Fax: +1 (408) 822-4501 Release date:
More informationReplacing a Failed Power-Fan Canister in the E5612 or the E5624 Controller-Drive Tray
Replacing a Failed Power-Fan Canister in the E5612 or the E5624 Controller-Drive Tray To access this product, go to the NetApp Support Site at mysupport.netapp.com. Before you replace the power-fan canister
More informationStorageGRID Webscale 10.4 Swift Implementation Guide
StorageGRID Webscale 10.4 Swift Implementation Guide April 2017 215-11701_A0 doccomments@netapp.com Table of Contents 3 Contents OpenStack Swift API support in StorageGRID Webscale... 4 History of Swift
More informationReplacing a Failed Drive in the EF550 Flash Array
Replacing a Failed Drive in the EF550 Flash Array To access this product, go to the NetApp Support Site at support.netapp.com. You can determine whether you have a failed drive in two ways: The Recovery
More informationCluster Expansion Express Guide
ONTAP 9 Cluster Expansion Express Guide June 2017 215-11193-E0 doccomments@netapp.com Updated for ONTAP 9.2 Table of Contents 3 Contents Deciding whether to use this guide... 4 Cluster expansion workflow...
More informationReplacing a Failed Host Interface Card in the E5560 Controller- Drive Tray
Replacing a Failed Host Interface Card in the E5560 Controller- Drive Tray ATTENTION Possible equipment damage Only a qualified service technician should perform this procedure, or equipment damage might
More informationInstalling a Cisco Nexus 5596 cluster switch and passthrough panel in a NetApp cabinet
Installing a Cisco Nexus 5596 cluster switch and passthrough panel in a NetApp cabinet These instructions describe how to install the Cisco Nexus 5596 switch and pass-through panel in a NetApp cabinet.
More informationSimulate ONTAP 8.1 Installation and Setup Guide
Simulate ONTAP 8.1 Installation and Setup Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 USA Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone: +1 (888) 4-NETAPP Documentation
More informationAltaVault Cloud Integrated Storage Installation and Service Guide for Virtual Appliances
AltaVault Cloud Integrated Storage 4.4.1 Installation and Service Guide for Virtual Appliances April 2018 215-130007_B0 doccomments@netapp.com Table of Contents 3 Contents System requirements and supported
More informationReplacing a Failed Controller Battery in the E5560 Controller- Drive Tray
Replacing a Failed Controller Battery in the E5560 Controller- Drive Tray To access this product, go to the NetApp Support Site at support.netapp.com. You can determine whether you have a failed controller
More informationReplacing a Failed Controller Battery in the E2712 Controller- Drive Tray or the E2724 Controller-Drive Tray
Replacing a Failed Controller Battery in the E2712 Controller- Drive Tray or the E2724 Controller-Drive Tray To access this product, go to the NetApp support site at support.netapp.com. You can determine
More informationReplication between SolidFire Element OS and ONTAP
ONTAP 9 Replication between SolidFire Element OS and ONTAP August 2018 215-12645_D0 doccomments@netapp.com Table of Contents 3 Contents Deciding whether to use the Replication between SolidFire Element
More informationReplacing a Cisco Nexus 5010 cluster switch
Replacing a Cisco Nexus 5010 cluster switch Replacing a defective Cisco Nexus 5010 cluster switch in a cluster network is a nondisruptive procedure (NDU). Before you begin The following conditions must
More informationSnapDrive for Windows Release Notes
IBM System Storage N series SnapDrive 7.0.3 for Windows Release Notes GC26-7881-24 Contents New in this release............................ 1 Upgrade notes.............................. 1 Changed commands............................
More informationFPolicy Solution Guide for Clustered Data ONTAP: Veritas Data Insight
Technical Report FPolicy Solution Guide for Clustered Data ONTAP: Veritas Data Insight Brahmanna Chowdary Kodavali and Saurabh Singh, NetApp Himanshu Ashwani, Veritas Data Insight November 2015 TR-4473
More informationSUPPORTING CLUSTERED DATA ONTAP: NODE MANAGEMENT
OFFERED BY: CUSTOMER SUCCESS OPERATIONS KNOWLEDGE MANAGEMENT ADVANCED TECHNICAL TRAINING SUPPORTING CLUSTERED DATA ONTAP: NODE MANAGEMENT EXERCISE GUIDE Content Version: 0.9 This page left intentionally
More informationSANtricity Storage Manager Express Guide
SANtricity Storage Manager 11.25 Express Guide For VMware and Fibre Channel NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone:
More informationReplacing the NVDIMM battery
AFF A800 systems Replacing the NVDIMM battery To replace the NVDIMM battery, you must remove the controller module, remove the battery, replace the battery, and then reinstall the controller module. About
More informationFPolicy Solution Guide for Clustered Data ONTAP: Veritas Enterprise Vault
Technical Report FPolicy Solution Guide for Clustered Data ONTAP: Veritas Enterprise Vault Brahmanna Chowdary Kodavali and Saurabh Singh, NetApp Bhushan Pandit and David Scott, Veritas February 2016 TR-4488
More informationCluster Switch Setup Guide for Cisco Switches. May _A0_UR006
Cluster Switch Setup Guide for Cisco Switches May 2018 215-06775_A0_UR006 doccomments@netapp.com Table of Contents 3 Contents Switches supported by ONTAP... 4 Setting up the switches... 5 Required cluster
More informationSimulate ONTAP 9.3. Installation and Setup Guide. NetApp, Inc. 495 East Java Drive Sunnyvale, CA U.S.
Simulate ONTAP 9.3 Installation and Setup Guide NetApp, Inc. 495 East Java Drive Sunnyvale, CA 94089 U.S. Telephone: +1 (408) 822-6000 Fax: +1 (408) 822-4501 Support telephone: +1 (888) 463-8277 Web: www.netapp.com
More informationAntivirus Configuration Guide
ONTAP 9 Antivirus Configuration Guide November 2017 215-11140_E0 doccomments@netapp.com Updated for ONTAP 9.3 Table of Contents 3 Contents Deciding whether to use the Antivirus Configuration Guide...
More informationPerformance Characterization of ONTAP Cloud in Azure with Application Workloads
Technical Report Performance Characterization of ONTAP Cloud in NetApp Data Fabric Group, NetApp March 2018 TR-4671 Abstract This technical report examines the performance and fit of application workloads
More informationLearning About Cloud Manager and ONTAP Cloud
OnCommand Cloud Manager 3.3 Learning About Cloud Manager and ONTAP Cloud March 2018 215-12279_E0 doccomments@netapp.com Updated for Cloud Manager 3.3.3 Table of Contents 3 Contents OnCommand Cloud Manager
More informationReplacing a Failed Controller Canister in the E5660 Controller- Drive Tray
Replacing a Failed Controller Canister in the E5660 Controller- Drive Tray To access this product, go to the NetApp support site at mysupport.netapp.com. You can determine whether you have a failed controller
More information